NTH - Management Information System

National Test House (NR), Ghaziabad

Kamla Nehru Nagar, Ghaziabad, Uttar Pradesh - 201002, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

7003775955 director-gzb[at]nth[dot]gov[dot]in

Scope List

Reset

616 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

301

IS 2046 NR CIVIL (1995 Reaffirmed 2005) - Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.5 (Resistance to Surface Wear)	5000.0
5.5 (Resistance to Crazing)	1500.0
5.5 (Flexural Strength)	4000.0
5.5 (Tensile Strength)	4000.0
5.5 (Resistance to Steam)	2000.0
5.5 (Resistance to Cigaretee Burns)	2000.0
5.5 (Resistance to Staining)	2000.0
5.5 (Resistance to Cracking)	2000.0
5.5 & 5.3 (Dimensions-Length, Width, Thickness, Wraping (Flatness), Reverse Side Bonding)	4000.0
5.5 (Resistance to Immersion in Boiling Water (Mass increase, Thickness increase, Appearance))	3500.0
5.5 (Resistance to dry heat at 180 degree centigrade)	2000.0
5.4 (Surface Defects)	1000.0
5.4.2 (Edge Defects)	1000.0
5.4.3 (Broken Corners)	1000.0
5.4.4 (Sanding Defects)	1000.0
5.4.8 (Squareness)	1000.0
5.5 (Dimensional Stability at Elevated Temperature (L, T))	1500.0
5.5 (Resistance to Scratch)	2000.0

302

IS 15573 (2018) - Polyaluminium Chloride

Polyaluminium Chloride

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Aluminium as Al2O3)	1200.0
4.2 (Relative Basicity)	1200.0
4.2 (Chloride as Cl)	700.0
4.2 (Sulphate as SO4)	700.0
4.2 (pH of 5 percent solution)	1200.0
4.2 (Insoubles)	1200.0
4.2 (Specific gravity at 25 deg C)	500.0
4.2 (Dynamic viscosity at 20 deg C)	500.0
4.2 (Mercury (as Hg,)	700.0
4.2 (Arsenic (as As))	700.0
4.2 (Cadmium (as Cd))	500.0
4.2 (Lead (as Pb))	700.0
4.2 (Iron (as Fe))	500.0
4.2 (Manganese (as Mn))	500.0
4.2 (Chromium (as Cr))	500.0
4.2 (Selenium (as Se))	500.0

303

Custom NDT NR - -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
NA (Chemical Composition)	3000.0
NA (Tensile Strength)	1000.0
NA (Yield Strength)	1000.0
NA (% Elongation)	1000.0
NA (Hardness)	2000.0
NA (Bend Test)	1000.0
NA (Charpy Impact Test)	3000.0
NA (Dimension)	1000.0
NA (Microstructure Analysis)	3000.0
NA (Grain Size)	3000.0
NA (Inclusion Rating)	3000.0
NA (Depth of Decarburization)	3000.0
0 (Magnetic Particle Inspection Test)	2000.0
0 (Ultrasonic Test)	4000.0
0 (Visual Inspection)	1000.0
1 (Proof Load Test)	3000.0
0 (Macro each Test)	3000.0

304

IS 2547 : Part 1 (1976) - Specification for gypsum building plaster: Part 1 excluding premixed lightweight plasters

Specification for gypsum building plaster: Part 1 excluding premixed lightweight plasters

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 1 Clause 4.1 (Loss of Ignition , percent by mass)	1000.0
Table 1 Clause 4.1 (Free Lime , Percent by mass)	1000.0
Table 1 Clause 4.1 (Sodium Soluble Salts, expressed as percentage of Na2O)	1000.0
Table 1 Clause 4.1 (Soluble Magnesium salts, expressed as percentage of MgO)	1500.0
Table 1 Clause 4.1 (CaO, Percent by mass)	1500.0
Table 1 Clause 4.1 (SO3, Percent by mass)	1000.0

305

IS:16353-2015 -CLINKER - PORTLAND CEMENT CLINKER

PORTLAND CEMENT CLINKER

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 1 Cl 5 (Ratio of percentage of Alumina to that of Iron Oxide)	1000.0
Table 1 Cl 5 (Ratio of percentage of lime to percentages of silica, alumina and iron oxide)	1000.0
Table 1 Cl 5 (Total sulphur content calculated as sulphuric anhydride (SO3))	500.0
Table 1 Cl 5 (Free lime, percent by mass,)	1500.0
Table 1 Cl 5 (Chloride content, percent by mass,)	200.0
Table 1 Cl 5 (Magnesia (as MgO), percent by mass)	1500.0
Table 1 Cl 5 (Insoluble residue, percent by mass)	500.0
Table 1 Cl 5 (Total loss on ignition , Percent by mass)	500.0
Table 1 Cl 5 (Silica (as SiO2), Percent by mass)	500.0
Table 1 Cl 5 (Aluminium Oxide (as Al2O3), Percent by mass)	500.0
Table 1 Cl 5 (Iron Oxide (as Fe2O3), Percent by mass)	500.0
Table 1 Cl 5 (Alkali content (as Na2O), percent by mass)	500.0
Table 1 Cl 5 (Alkali Content (as K2O). Percent by mass)	500.0
Table 1 Cl 5 (Calcium Oxide (as CaO), Percent by mass)	1000.0

306

11087. (1986) - Specification For Paper For Magnetic Ink Character Recognition Cheque Printing.

Specification For Paper For Magnetic Ink Character Recognition Cheque Printing.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.4 (Thickness)	1000.0
3.3 (Substance)	1000.0
3.6 (Smoothness)	1000.0
3.6 (Porosity)	1000.0
3.6 (Opacity)	2000.0
3.6 (Wax pick)	2000.0
3.6 (Tearing Strength)	2000.0
3.6 (Stiffness)	1000.0
3.9 (Chemical Sensitize Test)	10000.0
Firm's Requirement (Ash Content)	2000.0
Firm's Requirement (Moisture Content)	1000.0
3.8 (Watermark)	1000.0
Clause 3.1 (Description (Visual and workmanship requirements))	1000.0
Firm's Requirement (Colour of Paper)	1000.0

307

Custom - EN rod DIN1651

EN rod DIN1651

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon)	1200.0
2 (Manganese)	1200.0
3 (Sulphur)	1200.0
4 (Phosphorus)	1200.0
5 (Silicon)	1200.0
6 (Lead)	1200.0

308

IS 15622 Reaffirmed (2017) - Pressed ceramic tiles [All Tests IS 13630]

Pressed ceramic tiles

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6, Table 5 to 9, Sl.(iii),(a) (Resistance to Staining IS 13630 (8):2019)	1000.0
6, Table 5 to 9, Sl.(iii),(b) (Resistance to house hold chemicals swimming pools and water cleansing agents containing hydrofluoric acid and its compounds (IS 13630 (8):2019)	1500.0
6, Table 5 to 9, Sl.(iii),(c) (Resistance to Acid and Alkalies (with exception of hydrofloric acid and its compounds) IS 13630 (8):2019)	1500.0
6, Table 9, Sl.(iii),(a,b,c) (Chemical properties - unglazed Tiles - IS 13630 (7):2019)	3000.0
6, Table 5 to 9, Sl.(iii),(a,b,c) (Chemical properties - Glazed Tiles - IS 13630 (8):2019)	3000.0
iii (Chemical Properties [as per IS 13630 (Part 8- Glazed tiles)/ (Part 7 - Unglazed Tiles)])	2500.0
4.2 (Water Absorption, %)	1000.0
4.2 (Crazing)	1500.0
6, Table 5 (Impact Resistance)	1000.0
6, Table 5 (Dimensions-Length)	1000.0
6, Table 5 (Dimensions-Breadth)	1000.0
6, Table 5 (Dimensions-Thickness)	1000.0
6, Table 5 (Modulus of Rupture)	2000.0
6, Table 5 (Breaking Strength)	2000.0
6, Table 5 (Scratch Hardness)	2000.0
6, Table 8 & 9 (Bulk Density)	1000.0
6, Table 5 (Rectangularity)	500.0
6, Table 5 (Straightness)	500.0
6, Table 5 (Flatness)	500.0
6, Table 5 (Modulus of Rupture without Breaking strength)	3000.0
6, Table 5 (Breaking Strength without MoR)	3000.0

309

IS 809 (1992) - Rubber flooring materials for general purposes - Specification (First Revision)

Rubber flooring materials for general purposes - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Appearance)	500.0
4.2 (Colour)	500.0
5.1 (Thickness)	500.0
5.2 (Tile Size)	500.0
5.2 (Squareness)	1000.0
6.1 (Hardness)	2000.0
6.1.1 (Tolerance on Hardness)	500.0
6.2 (Water Absorption)	1000.0
6.3 (Compression Set)	2000.0

310

IS 383 (2016) - Coarse and Fine Aggregate for Concrete - Specification (Third Revision) [All Tests 2386]

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (IS:2386(Pt.-1)_Size and Grading of Aggregates-Sieve Analysis)	2000.0
5.6 (Alkali aggregate reactivity, m.mol/lit.)	3000.0
5.4.3 (IS:2386(Pt.-4)_Abrasion Value, %)	1500.0
5.4.2 (IS:2386(Pt.-4)_Impact Value, %)	1500.0
5.4.1 (IS:2386(Pt.-4)Crushing Value)	1500.0
5.3 (Combined Elongation Index and Flakiness Index)	3000.0
5.2 (Deleterious materials)	2000.0
5.5 (IS:2386(Pt.-5)_Soundness)	2000.0

311

NTH/NR/XR/HDPE Sheathing (2023) - Specification for HDPE Sheathing

Specification for HDPE Sheathing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Density)	1000.0
2 (Dimensions)	1000.0
3 (Wall Thickness)	1000.0
3 (Tensile Strength)	1000.0
4 (Elongation)	1000.0
5 (Shore Hardness)	1000.0
6 (Melt Flow Index)	2000.0
Firm's Requirement (Charpy Impact Strength)	3000.0

312

IS 14543 (2024) - Packaged Drinking Water (other than Packaged Natural Mineral Water) - Specification

Packaged Drinking Water (other than Packaged Natural Mineral Water) - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl No. 5 (Test parameters as per attached Annexure B)	5000.0
Cl No. 5 Table 1, 2 & 3 (Test parameters as per attached Annexure A)	15000.0
Cl no 5 Table 3 (All Microbiological parameters (PLEASE SEE THE ANNEXURE)- NABL))	5000.0
Cl no 5 Table 3 (All Microbiological Parameters (PLEASE SEE THE ANNEXURE)- NON NABL))	1.0

313

MORTH 803 Thermoplastic Road Marking Material MORTH-5th Revision 2013 (2013) - Ministry of Road Transport and Highways - Specifications form Road And Bridge Works 803.4.2

Ministry of Road Transport and Highways - Specifications form Road And Bridge Works 803.4.2

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
803.4.2.3 (Free flowing properties)	500.0
803.4.2.3 (Roundness)	1000.0
803.4.2.3 (Gradation (Type 2) - below 180 micron(BS 6088))	700.0
803.4.2.3 (Gradation (Type 2) - 180 micron (BS 6088))	500.0
803.4.2.3 (Gradation (Type 2) - 300 micron (BS 6088))	600.0
803.4.2.3 (Gradation (Type 2) - 600 micron (BS 6088))	600.0
803.4.2.3 (Gradation (Type 2) - 850 micron (BS 6088))	600.0
803.4.2.3 (Gradation (Type 1) - 180 micron (BS 6088))	750.0
803.4.2.3 (Gradation (Type 1) - 425 micron (BS 6088))	750.0
803.4.2.3 (Gradation (Type 1) - 850 micron (BS 6088))	750.0
803.4.2.3 (Gradation (Type 1) 1.18mm (BS 6088))	750.0
803.4.2.3 (Appearance)	500.0
803.4.2 (Yellowness Index)	1000.0
803.4.1.2 (Flow resistance (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Softening point (BS 3262 (Part 1)) ASTM D 36)	1200.0
803.4.1.2 (Cracking Resistance (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Skid Resistance)	1000.0
803.4.1.2 (Drying Time)	1200.0
803.4.1.2 (Luminance (Yellow))	1200.0
803.4.1.2 (Luminance (White) (Daylight luminance at 45 degrees))	1200.0
803.4.1.2 (Calcium carbonate and Inert fillers (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Binder Content % by mass (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Colour)	1200.0
803.4.1.2 (Titanium Dioxide, as TiO2 % by mass (BS 3262 (Part 1)))	1200.0
803.4.1.2 (Glass Bead content % (BS 3262 (Part 1)))	1200.0

314

IS 1264 (1997) - Brass gravity die castings - Specification (Fourth Revision)

Brass gravity die castings - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 Table 1 (Copper)	1000.0
7.1 Table 1 (Tin)	500.0
7.1 Table 1 (Lead)	500.0
7.1 Table 1 (Nickel)	500.0
7.1 Table 1 (Iron)	500.0
7.1 Table 1 (Aluminium)	500.0
7.1 Table 1 (Manganese)	500.0
7.1 Table 1 (Silicon)	500.0
7.1 Table 1 (Total Impurities (excluding Ni+Pb+Al))	500.0
7.1 Table 1 (Zinc)	1000.0

315

IS-9537(Part-II)-1981 Reaff. 2017 - Conduits for Electrical Installations- Rigid Steel Conduits

Conduits for Electrical Installations- Rigid Steel Conduits

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

316

IS 9537:Part 3 (1983) - Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating materials

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating materials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Dimensions)	1000.0
7.4 (Uniformity of Thickness)	1000.0
8 (Construction)	1000.0
9.2 (Bending Test)	2000.0
9.3 (Compression Test)	2000.0
9.4 (Impact Test)	2000.0
9.5 (Collapse Test)	2000.0
11 (Resistance to Burning)	2000.0

317

WD-01-HLS-94(Rev-03) (Amdt. No.4 of Oct 2020 Para No: 2.4) - Metallurgical Test of Spring Steel

Metallurgical Test of Spring Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Chemical Composition As per IS 3195)	4500.0
- (Metallurgical Test)	23500.0

318

IS 16172 (2023) - Reinforcement couplers for mechanical splices of bars in concrete - Specification

Reinforcement couplers for mechanical splices of bars in concrete - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2 (Tensile Strength as per IS 1608(Part 1):2022)	1500.0
9.2 (Percentage Elongation as per IS 1608(Part 1):2022)	1500.0
9.2 (Visual Observation for Nature & Location of failure of spliced specimen (With Coupling).)	1000.0
8 (Chemical composition, % by mass)	3000.0

319

NTH/NR/RPPT/Polycarbonate Sheet - Customized specification for Polycarbonate Sheet

Customized specification for Polycarbonate Sheet

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's Requirement (Length)	500.0
Firm's Requirement (Width)	500.0
Firm's Requirement (Thickness)	1000.0
Firm's Requirement (Melt Flow Index)	2000.0
Firm's Requirement (Luminous Transmittance)	2000.0
Firm's Requirement (Density)	1000.0
Firm's Requirement (Tensile Strength at Yield)	1000.0
Firm's Requirement (Tensile Modulus)	1000.0
Firm's Requirement (Flexural Strength)	2000.0
Firm's Requirement (UV Layer (Top & Bottom))	2000.0

320

NTH/NR/RPPT/Miscellaneous/01 (2023) - Testing of Miscellaneous Items

Testing of Miscellaneous Items

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's Requirement (Result of Tests)	5000.0
Firm's Requirement (Results of Test (Mechanical))	20000.0
Firm's Requirement (Results of Test (Electrical))	10000.0
Firm's Requirement (Results of Test (Chemical))	5000.0
Firm's Requirement (Density)	2000.0
Firm's Requirement (Thickness)	1000.0
Firm's Requirement (Dimensions)	5000.0
Firm's Requirement (Weight)	1000.0

321

IS 9755 (2021) - Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Visual Inspection Test)	500.0
Table-1 (Dimensions)	1000.0
Table-1 (Ends/dm)	500.0
Table-1 (Picks/dm)	500.0
Table-1 (Mass of Fabric)	1000.0
Table-1 (Mass of Sack)	500.0
Table-1 (Breaking Strength (Lengthwise))	750.0
Table-1 (Breaking Strength (Widthwise))	750.0
Table-1 (Breaking Strength (Widthwise) of Laminated joint (for laminated sacks))	1000.0
Table-1 (Breaking Strength of bottom seam)	1000.0
Table-1 (Elongation@break of fabric (Lengthwise))	750.0
Table-1 (Elongation@break of fabric (Widthwise))	750.0
Table-1 (Ash Content)	2000.0

322

IS 7834 (Part-1) (1987) - INJECTION MOULDED PVC SOCKET FITTINGS WITH SOLVENT CEMENT JOINTS FOR WATER SUPPLIE

INJECTION MOULDED PVC SOCKET FITTINGS WITH SOLVENT CEMENT JOINTS FOR WATER SUPPLIE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Size of Fitting)	500.0
4 (Minimum Thickness)	500.0
5.1 (Socket Length)	500.0
5.1.2 (Minimum ID at Mid-Point)	500.0
5.1.2 (Maximum ID at Mid-Point)	500.0
6.1 (Stress Relief Test)	5000.0
6.2 (Opacity (%))	1000.0
6.4 (Short Term Hydraulic Test)	5000.0
6.3 (Effect on Water)	2000.0

323

NTH/NR/Cust Spec/T-Shirt/2023/01 - NTH/NR/Cust Spec/T-Shirt/2023/01

NTH/NR/Cust Spec/T-Shirt/2023/01

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Mass)	1000.0
2.0 (Fiber Composition)	3000.0

324

IS 15852 (2009) - Textiles – Polyester blended woven shirting for uniforms

Textiles – Polyester blended woven shirting for uniforms

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Mass)	2000.0
4 (Fibres composition)	2000.0

325

Custom-Mech-NR - Custom-Mech-NR

Custom-Mech-NR

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
NA (Proof Load Test)	3000.0
NA (Magnetic Particle Test)	4000.0
NA (Ultrasonic Test)	4000.0
NA (Visual Inspection Test)	1000.0
NA (Chemical Composition)	5000.0
NA (Hydrostatic Test)	5000.0
NA (Pneumatic Test)	5000.0
NA (Tensile Test)	3000.0
NA (Test of Polymer)	8000.0
- (Radiography Test)	2000.0
- (Coating Test)	8000.0

326

IRSM 28 (2017) - Indian Railway Standard Specification For Classification, Testing And Acceptance Criteria Of Manual Metal Arc Welding Electrodes And Gas Welding Rods

Indian Railway Standard Specification For Classification, Testing And Acceptance Criteria Of Manual Metal Arc Welding Electrodes And Gas Welding Rods

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
As Per IRSM 28:2017 (Testing of Stainless Steel Flux covered Electrode)	16500.0
NA (Weld Assembly Preparation)	5000.0
6.2.2 (Table-5) (Transverse Bend Test)	3000.0

327

NTH/NR/Cust Spec/UPVC Profile/2023/01 - Customer Specification for UPVC Profiles and Sections

Customer Specification for UPVC Profiles and Sections

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Vicat Softening Temperature)	1500.0
2 (Heat Reversion Test)	2000.0
3 (Titanium Di-oxide)	1500.0
4 (Calcium Carbonate)	1500.0

328

Cust Spfn UPVC Windows/Doors Profile - UPVC Windows/Doors Profile

UPVC Windows/Doors Profile

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Vicat Softening Temperature at 5kg load)	1500.0
18 (Heat Reversion Test)	2000.0
19 (Titanium Di-oxide)	2000.0
20 (Calcium Carbonate)	2000.0

329

1537 - Specification for Vertically cast iron pressure pipes for water, gas and sewage.

Specification for Vertically cast iron pressure pipes for water, gas and sewage.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Tensile Strength)	3000.0
4.2 (Brinell Hardness Test)	2000.0
6 (Hydrostatic Test)	5000.0
7 (Dimensions)	1000.0
9 (Mass)	1000.0
10.4 (Coating Test)	1000.0

330

1124-1974 RA 2003 (1974 RA 2003) - Method of test for Water absorption, Apparent Specific Gravity and Porosity of Natural Building Stone

Method of test for Water absorption, Apparent Specific Gravity and Porosity of Natural Building Stone

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 of 1124 (Water Absorption)	1000.0
4.2 (Specific Gravity)	500.0