NTH - Management Information System

National Test House (NR), Ghaziabad

Kamla Nehru Nagar, Ghaziabad, Uttar Pradesh - 201002, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

7003775955 director-gzb[at]nth[dot]gov[dot]in

Scope List

Reset

608 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

571

IS 2202 : Part 1 (2023) - Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

Wooden flush door shutters (Solid Core Type) - Specification: Part 1 plywood face panels (Sixth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.15 (Screw Withdrawal Resistance Test-IS 4020 (Part 16):1998)	1500.0
11.14 (Glue Adhesion Test-IS 4020 (Part 15):1998 for BWP and (60± 2)°C for MR)	1000.0
11.13 (Knife test-IS 4020 (Part 14):1998)	1000.0
11.12 (End Immersion Test-IS 4020 (Part 13):1998 for BWP and 3cycle for MR)	1000.0
11.11 (Varying Humidity Test-IS 4020 (Part 12):1998)	3000.0
11.10 (Misuse Test-IIS 4020 (Part 11):1998)	1000.0
11.9.2 or 11.9.3 (Slamming Test-Cl 2.1 or 3.1 of IS 4020 (Part 10):1998)	1000.0
11.8 (Buckling Test-IS 4020 (Part 9):1998)	1500.0
11.7.1 and 11.7.2 (Shock Resistance test- Cl 2.1 & 3.1 of IS 4020 (Part 8):1998)	1500.0
11.6 (Edge loading test-IS 4020 (Part 7):1998)	1500.0
11.5 (Flexure Test-IS 4020 (Part 6):1998)	1000.0
11.4 (Impact Indentation-IS 4020 (Part 5):1998)	1000.0
11.3 (Local planeness Test-IS 4020 (Part 4):1998)	1000.0
11.2 (General Flatness-IS 4020 (Part 3):1998)	1000.0
11.1 (Dimensions and Squareness-IS 4020 (Part 2):1998)	2000.0
9 (Workmanship and Finish-IS 2202 (Part 1):1999)	1000.0

572

303 (2024) - Plywood for General Purpose

Plywood for General Purpose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.3.2 (Mycological Test)	1500.0
11.3.1 (a) (Glue Adhesion - Water Resistance Test)	2000.0
11.5 (Static Bending Test along the Grain direction (Modulus of Rupture & Modulus of Elasticity), N/mm^2)	1500.0
11.4 (Moisture Content, in %)	1000.0
9 (Workmanship and finish,)	2000.0
5 (Classification by Appearance)	1500.0
8.1 (Length, in mm)	400.0
8.1 (Width, in mm)	400.0
8.2 (Thickness, in mm)	400.0
8.3 (Squareness, in mm/m)	400.0
8.3 (Edge Straightness, in mm/m)	400.0
11.6 (Formaldehyde Content Test, in mg/100g)	3000.0
11.5 (Static Bending Test across the Grain direction (Modulus of Rupture & Modulus of Elasticity), N/mm^2)	1500.0
11.5 (Static Bending Strength (Modulus of Rupture -Along), in N/mm^2)	750.0
11.5 (Static Bending Strength (Modulus of Rupture - Across), in N/mm^2)	750.0
11.5 (Static Bending Strength (Modulus of Elasticity-Along), in N/mm^2)	750.0
11.5 (Static Bending Strength (Modulus of Elasticity- Across), in N/mm^2)	750.0
11.5 (Static bending Strength along the grain direction [IS 1734 (Part 11)])	1500.0
11.5 (Static bending Strength across the grain direction [IS 1734 (Part 11)])	1500.0

573

IS 4990 (2011) - Plywood for concrete shuttering works - Specification (Third Revision)

Plywood for concrete shuttering works - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 (Workmanship & Finish- IS 4990:2011,)	1000.0
10.1.8, Table 3 (Wet Bending Strength--IS 4990:2011 & IS 1734 (Part 11):1983)	2000.0
10.1.7, Table 2 (Static Bending Strength-IS 1734 (Part 11):1983)	2000.0
10.1.6 (Tensile Strength-IS 1734 (Part 9):1983)	2500.0
10.1.5.2 (Glue Adhesion, after Mycological Test-IS 1734 (Part 7):1983 & IS 1734 (Part 5):1983 -)	500.0
10.1.5.1 (Glue Shear Strength, after Mycological Test-IS 1734 (Part 7):1983 & IS 1734 (Part 4):1983)	2000.0
10.1.3.1.2 (Glue Adhesion, after, after water resistance-IS 4990:2011 & IS 1734 (Part 5):1983)	500.0
10.1.3.1.1 (Glue Shear Strength, after Water Resistance-IS 4990:2011 & IS 1734 (Part 4):1983)	2000.0
10.1.2.2 (Adhesion of Plies in dry state-IS 1734 (Part 5):1983)	1000.0
10.1.2.1 (Glue Shear Strength in dry state-IS 1734 (Part 4):1983)	2000.0
10.1.1 (Moisture content-IS 4990:2011 & IS 1734 (Part 1):1983)	1000.0
7 (Dimension and Tolerances- IS 4990:2011, Annex C)	1000.0

574

IS 1659 (2004) - Block boards - Specification (Fourth Revision)

Block boards - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1.3 (Defects--IS 1659:2004, Clause 6.3.3 and IS 303 / IS 1328)	1000.0
9.2.6 (Spot Test-IS 1659:2004, Clause 8.2.3 & Annex K)	2000.0
9.2.5 (Modulus of Rupture & Modulus of Elasticity-IS 1659:2004, Clause 8.2.3 & Annex J)	2000.0
9.2.4 (Mycological Tests-IS 1659:2004, Clause 8.2.3 & Annex H)	2000.0
9.2.3 (Adhesion of Plies-IS 1659:2004, Clause 8.2.3 & Annex G)	1000.0
9.2.2 (Water Resistance Test -IS 1659:2004, Clause 8.2.3 & Annex F and G)	2000.0
9.2.1 (Dimensional Changes caused by Humidity-IS 1659:2004, Clause 8.2.3 & Annex E)	1000.0
7, 8.1.4, and 8.1.5 (Dimension & Tolerances-IS 1659:2004, Annex D)	1000.0
4.5 (Moisture content)	1000.0

575

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA) [1100 kVA to 2 500 kVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.3(b) (Temperatur Rise Test)	40000.0
21.2(a) (Measurement of Winding Resistance)	1000.0
21.2(b) (Measurement of voltage ratio and,check ofvoltage vector relationship)	2000.0
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	20000.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	5000.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	7000.0
21.2(c) (Measurement of impedance voltage (principal tapping), shortcurcuit impedance and load loss (At 50% and 100% load))	8000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	20000.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	1500.0
21.2(d) (Measurement of no Load and loss and current)	6000.0
21.2(f) (lnduced Over Voltage withstand test)	4000.0
21.4(a) (Determination of sound levels)	7000.0
21.4( e) (BDV of Oil in the tranformer)	10000.0
21.3(a) (Impulse Voltage)	35000.0
21.2(g) (AC High Voltage Withstand Test)	2500.0
21.3(a) (Impulse Voltage)	35000.0
21.3(a) (lmpulse Voltage)	65000.0
21.3(a) (lmpulse Voltage)	50000.0
21.3(a) (lmpulse Voltage)	40000.0
As per CBIP Pub No. 317 Cl. 3.17 (Magnetic Balance Test)	5000.0
As per CBIP Manual No. 317 Cl. (Harmonics of No-load Current)	15000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	5000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	5000.0
N.A. (Unbalance Current)	5000.0

576

IS 516 : Part 1 : Sec 1 (2021) - Hardened concrete methods of test part 1 testing of strength of hardened concrete section 1 compressive,flexucal and split tensile strength (First Revision)

Hardened concrete methods of test part 1 testing of strength of hardened concrete section 1 compressive,flexucal and split tensile strength (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

577

IS 9103 (1999) - Specification for Concrete Admixtures -

Specification for Concrete Admixtures -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.2.1 (Comparative Compressive strength for one duration of concrete)	5000.0
7.2.1 (Slump of Control Concrete Mix at 15 Minutes)	2000.0
9 (pH)	1000.0
9 (Chloride ion content)	1000.0
9 (Relative density)	1000.0
9 (Ash content)	1000.0
9 (Dry Material content)	1000.0
7.2.3 (Setting time of concrete additive allowable Deviation from control sample)	2000.0
Cl. 9 (Please see the Annexure (Customer Requirement))	11000.0
8.2.1 (Comparative Compressive strength for one duration of concrete)	5000.0
7.2.5 (Water content of Concrete additive)	1000.0
8.2.1 (Comparative Compressive strength for three duration of concrete)	10000.0

578

IS 6911 (2017) - Stainless steel plate, sheet and strip - Specification (Second Revision)

Stainless steel plate, sheet and strip - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10 (Tensile strength)	1000.0
10 (Hardness )	2000.0
10 (Elongation)	1000.0
10 (Yield Stress)	1000.0
6 (Visual examination)	1000.0
7 (Chemical Analysis (PLEASE SEE THE ANNEXURE))	5000.0
0 (Dimensions)	1000.0
0 (Mass per metre, kg)	1000.0
7.1&7.2,Table 1 (Chemical Analysis (Please see Annexure)- NON NABL)	1000.0
0 (Hydrostatic Pressure Test)	5000.0

579

FCO -1985 (1985) - The Fertiliser (Control) Order 1985 (as amended upto Nov 2023)

The Fertiliser (Control) Order 1985 (as amended upto Nov 2023)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Schedule I Part A (Matter insoluble in water)	1000.0
Schedule I Part A (Sodium (as NaCl) on dry basis)	1000.0
Schedule I Part A (Water soluble Zinc (as Zn EDTA))	1000.0
Schedule I Part A (Water soluble potash (as K2O))	1000.0
Schedule I Part A (Water soluble phosphate (as P2O5))	1000.0
Schedule I Part A (Ammoniacal nitrogen)	1000.0
Schedule I Part A (Nitrate nitrogen)	1000.0
Schedule I Part A (Total nitrogen)	1000.0
Schedule I Part A (Moisture)	1000.0
Schedule I Part A (Sulphur (as S))	1000.0
Schedule I Part A (Sodium as NaCl)	1000.0
Schedule I Part A (Zinc (as Zn))	1000.0
Schedule I Part A (Boron (as B))	1000.0
Schedule I Part A (Neutral ammonium citrate soluble phosphates (as P2O5))	1000.0
Schedule I Part A (Arsenic (as As))	1000.0
Schedule I Part A (Magnesium as MgO)	1000.0
Schedule I Part A (pH)	1000.0
Schedule I Part A (Lead (as Pb))	1000.0
Schedule I Part A (Total chloride (as Cl) (On dry basis))	1000.0
Schedule I Part A (Available Phosphorous (as P2O5))	1000.0
Schedule I Part A (Sulphate Sulphur (as S))	1000.0
Schedule I Part A (Free Phosphoric Acid (as P2O5))	1000.0
Schedule I Part A (Cadmium (as Cd) percent by weight)	1000.0
Schedule I Part A (Iron (as Fe) percent by weight)	1000.0
Schedule I Part A (Neutral ammonium citrate soluble phosphate (as P2O5) )	1000.0
Schedule I Part A (Magnesium (as Mg))	1000.0
Schedule I Part A (Copper (as Cu))	1000.0
Schedule I Part A (Iron content (expressed as Fe) in the form of Fe-EDTA)	1000.0
Schedule I Part A (pH (5 % solution))	1000.0
Schedule 1 Part A (Total phosphorus (as P2O5))	1000.0
Schedule I Part A (Water Soluble Calcium Oxide (CaO))	1000.0
Schedule I Part A (Water Soluble Magnesium Oxide (MgO)- 5.5%)	1200.0
Schedule I Part A (Manganese (as Mn))	1000.0
Schedule I Part A (Urea nitrogen)	1000.0
Schedule I Part A (Total Elemental Sulphur (as S))	1000.0
Schedule I Part A (Total Nitrogen in the form of Urea percent by weight)	1000.0
Schedule I Part A (ALL TESTS AS PER FCO-1985 -(PLEASE SEE THE ANNEXURE)-NABL)	7000.0
Schedule I Part A (Biuret)	1000.0
Schedule I Part A (Particle size – Not less than 90 per cent of the material shall pass through 4 mm IS sieve and retained on 1mm IS sieve. Not more than 5 per cent shall be below 1 mm IS sieve.)	1000.0
Schedule I Part A (Free flowing – crystalline form)	1000.0
Schedule I Part A (Calcium nitrate)	1000.0
Schedule I Part A (ALL TESTS AS PER FCO-1985 -(PLEASE SEE THE ANNEXURE) NON NABL)	7000.0
Custom (7-above) (Test Results (as per Annexure/Form L; Non-NABL))	7000.0

580

IS 9537 : Part 2 (1981) - Specification for conduits for electrical installations: Part 2 rigid steel conduits

Specification for conduits for electrical installations: Part 2 rigid steel conduits

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2 (Checking the Maximum outside diameter)	750.0
7.2 (Checking the Minimum outside diameter.)	750.0
7 (Outside Diameter)	500.0
7 (Wall thickness)	500.0
9.3 (Compression Test)	3000.0
13 (External Influence Test (With Seam on the Outside of the Bend))	1000.0
13 (External Influence Test (With Seam on the flank))	1000.0
9.2 (Bending Test (With Seam on the flank))	500.0
9.2 (Bending Test (With Seam on the Outside of flank))	500.0
0.1 (Mass of Zn Coating)	2000.0
0.2 (Free bore test)	1000.0
0.3 (Uniformity of Zn Coating)	1000.0
0.4 (Adhesion Test)	1000.0

581

IS 269 (2015) - Ordinary portland cement - Specification (Sixth Revision)

Ordinary portland cement - Specification (Sixth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1, Table2, Sl No 8 (Alkali content IS 4032:1985)	1000.0
6.1, Table2, Sl No 7 (Chloride content IS 4032:1985)	500.0
6.1, Table2, Sl No 6 (Loss on ignition IS 4032:1985)	600.0
6.1, Table2, Sl No 5 (Total Sulphur content percent by mass, IS 4032:1985)	500.0
6.1, Table2, Sl No 4 (Magnesia IS 4032:1985)	600.0
6.1, Table2, Sl No 3 (Insoluble residue, IS 4032:1985)	600.0
6.1, Table2, Sl No 2 (Ratio of percentage of alumina to that of iron oxide IS 4032:1985)	600.0
6.1, Table2, Sl No 1 (Ratio of percentage of lime to percentages of silica, alumina and iron oxide, IS 4032 : 1985)	600.0
7, Table 3, Sl No 4c (Compressive strength, MPa (c) 672 ± 4 h IS 4031 (Part 6):1988)	1000.0
7, Table 3, Sl No 4b (Compressive strength, MPa (b) 168 ± 2 h IS 4031 (Part 6):1988)	1000.0
7, Table 3, Sl No 4a (Compressive strength, MPa-(a) 72 ± 1 h IS 4031 (Part 6):1988)	1000.0
7, Table 3, Sl No 3b (Setting time: b) Final, IS 4031 (Part 5):1988)	250.0
7, Table 3, Sl No 3a (Setting time: a) Initial IS 4031 (Part 5):1988)	250.0
7, Table 3, Sl No 2b (Soundness b) By autoclave test method IS 4031 (Part 3):1988)	1000.0
7, Table 3, Sl No 2a (Soundness: a) By Le-Chatelier method, IS 4031 (Part 3):1988)	500.0
7, Table 3, Sl No 1 (Fineness IS 4031 (Part 2):1999)	1000.0
4031 Part (4) (Consistency, %)	500.0

582

BSEN 13348 (2016) - Copper and Copper Alloy - Seamless Round Copper Tube for Medical Gases or vacuum

Copper and Copper Alloy - Seamless Round Copper Tube for Medical Gases or vacuum

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2 (Tensile Strength)	2000.0
6.1 (Cu + Ag)	4000.0
6.1 (Phosphorus (% by mass))	1000.0
6.2 (Elongation)	1000.0
6.2 (Hardness)	2000.0

583

IS 8110 (2019) - Water well screens and slotted pipes - Specification (Third Revision)

Water well screens and slotted pipes - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3.6 (Visual)	1000.0
5 (Chemical Analysis)	5000.0
8.3.4 (Tensile load)	5000.0
2 (Slotting arrangement)	1000.0
7.2 (Diameter of screen)	1000.0
8.1 (Thickness of pipe)	1000.0
3.1 (Sulphur (% by mass))	700.0
3.1 (Phosphorous (% by mass))	700.0

584

IS 4270 (2001) - Steel tubes used for water wells specification (Third Revision)

Steel tubes used for water wells specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
14 (Workmanship)	1000.0
5.2 (Sulphur)	1250.0
9 (Outside diameter)	3000.0
6.2 (Flattening)	1000.0
6.1 (Tensile test)	3000.0
7 (Weight in kg/m)	1000.0
7 (Thickness)	250.0
14 (Visual examination)	1000.0
6.1 (Yield Strength)	1000.0
6.1 (% Elongation)	1000.0
5.2 (Phosphorus)	1250.0

585

IS 1239 : Part 1 (2004) - Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12 (Galvanising (Mass of Zinc Coating))	2000.0
7 (Chemical Analysis ( As per Annexure))	3000.0
14.3 (Flattening Test on tube above 50 mm NB)	1000.0
14.2 (Bend test on tube (upto and including 50 mm NB))	1000.0
8.1 (Mass per meter)	1000.0
8 (Dimensions (Thickness), mm.)	1000.0
14.1.1(a) (% Elongation)	1000.0
14.1 (Tensile Strength)	2000.0
15 (Workmanship)	500.0
13 (Leak proof test)	2500.0
12 (Uniformity of Coating)	500.0
8 (Dimension (Outside diameter), mm.)	1000.0

586

IS 15138 (2010) - Textiles – Jute bags for packing 50 kg sugar – Specification (first revision)

Textiles – Jute bags for packing 50 kg sugar – Specification (first revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

587

IS 9537 : Part 1 (1980) - Specification for conduits for electrical installations: Part 1 general requirements

Specification for conduits for electrical installations: Part 1 general requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Compression Test (Compression Force: 1250 N))	3000.0

588

IS 6956 (2001) - Cover Paper

Cover Paper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3 (Grammage)	1000.0
4.2 (pH)	1000.0
4.2 (Tensile Index (MD))	1000.0
4.2 (Tensile Index (CD))	1000.0
4.2 (One Minute Cobb)	1000.0
4.2 (Opacity)	2000.0
4.2 (Brightness, %)	2000.0
4.2 (Burst Index)	2000.0
4.2 (Wax Pick)	2000.0
4.2 (Smoothness Bendsten)	2000.0
4.2 (Folding Endurance, CD)	750.0
4.2 (Folding Endurance, MD)	750.0
4.2 (Bending Stiffness Index, CD)	1000.0
4.2 (Bending Stiffness Index, MD)	1000.0
Firm's Requirement (Tear Index (CD))	1000.0
Firm's Requirement (Tear Index (MD))	1000.0
Firm's Requirement (Gloss)	1500.0
Firm's request (Thickness (Caliper))	1000.0
Firm's request (Bulk)	1000.0
4.1 (General)	1000.0
4.2 (Wax Pick)	2000.0

589

IS 16208 (2015) - Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

590

IS 14252 (2015) - Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

591

IS 11652 (2017) - Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

592

IS 10228 (1982) - Specification for school bag

Specification for school bag

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

593

IS 13592 (2013 (RA 2018)) - Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3 (Dimension of Grooved Socket)	500.0
7.1 (Average Wall Thickness)	500.0
7.1 (Minimum outside diameter at any point)	500.0
7.1 (Maximum outside diameter at any point)	500.0
7.1 (Mean Outside Diameter)	500.0
7.1 (Outside diameter at any point)	1000.0
5 (Colour)	500.0
7 (Dimensions (Outside Diameter, Wall thickness))	1000.0
8.1 (Visual Appearance)	1000.0
8.2 (Reversion test)	2000.0
8.3 (Stress relief test)	2000.0
8.4 (Vicat Softening Temperature)	1500.0
8.5 (Effect of Sunlight)	3000.0
9 (Resistance to Sulphuric Acid)	2000.0
10.1 (Impact Strength)	2000.0
10.2 (Tensile strength)	2000.0
10.3 (Axial Shrinkage)	2000.0

594

IS 15778 (2007) - Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Diameter)	1000.0
7.1.1 (Diameter at any point )	1000.0
7.1.2 (Wall Thickness)	1000.0
7.1.3 (Length)	1000.0
9.2 (Opacity)	2000.0
9.4 (Reversion Test)	2000.0
9.5 (Vicat Softening Temperature)	1500.0
9.6 (Density)	1000.0
10.1 (Hydrostatic Characteristics)	5000.0
10.4 (Flattening Test)	2000.0
10.3 (Resistance to External Blows)	2000.0
10.5 (Tensile Strength )	2000.0

595

IS 16098 Part 1 (2013) - Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

596

IS 14930 : Part 2 (2001) - Conduit Systems for Electrical Installations - Part 2 : Particular Requirements - Conduit Systems Burried Underground

Conduit Systems for Electrical Installations - Part 2 : Particular Requirements - Conduit Systems Burried Underground

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 8 (Dimensions)	2000.0
Clause 10.2 (Compression Test)	2000.0
Clause 10.3 (Impact Test)	2000.0

597

IS 9537 : Part 3 (1983) - Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (-)	-
7.4 (Uniformity of Wall Thickness)	1000.0
9.3 (Compression Test)	2000.0
9.4 (Impact Test)	2000.0
9.2 (Bending Test at Room Temp)	500.0
9.5 (Collapse Test)	1000.0

598

IS 4658 (2019) - Specification for coated paper and board (Art And Chromo) (Second Revision)

Specification for coated paper and board (Art And Chromo) (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Thickness)	1000.0
5.3 (Substance (Grammage))	1000.0
5.4 (Size and Tolerance )	1000.0
5.5 (Burst Index )	2000.0
5.5 (Cobb Value)	1000.0
Firm's requirement (Smoothness)	2000.0
5.5 (Bulk)	1000.0
5.5 (Gloss)	1500.0
5.5 (Surface pH)	1000.0
Firm's requirement (Tensile Index)	2000.0
5.5 (Stiffness Factor)	1000.0
Firm's requirement (Tear Index(CD))	1000.0
Firm's requirement (Tear Index (MD))	1000.0
Firm's Requirement (Opacity, %)	2000.0
Firm's requirement (Smoothness)	2000.0
5.5 (Brightness)	2000.0
5.5 (Wax Pick)	2000.0
Firm's requirement (Double Fold (CD))	750.0
Firm's Requirement (Double Fold (MD))	750.0

599

IS 1848 : Part 2 (2018) - Writing and printing papers - Specification: Part 2 air mail/manifold, cartridge drawing and cartridge white, duplicating absorbent and duplicating semi - Absorbent and poster machine glazed types (Fifth Revision)

Writing and printing papers - Specification: Part 2 air mail/manifold, cartridge drawing and cartridge white, duplicating absorbent and duplicating semi - Absorbent and poster machine glazed types (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

600

IS 1848 : Part 1 (2018) - Writing and printing papers - Specification: Part 1 account book, azure lead, bond, cream laid and cream wove/printing white/printing coloured/printing offset, printing maplitho, printing white super calendered and typewriting types (Fifth Revision)

Writing and printing papers - Specification: Part 1 account book, azure lead, bond, cream laid and cream wove/printing white/printing coloured/printing offset, printing maplitho, printing white super calendered and typewriting types (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Substance (Grammage), g/sq.m)	1000.0
4.6 (i) (Tensile Index (MD))	1000.0
4.6 (i) a (Tensile Index (CD))	1000.0
4.6(ix) (Tear Index (CD))	1000.0
4.6 (ix) (Tear index(MD))	1000.0
4.6 (Opacity, %)	2000.0
4.6 (One Minute Cobb)	1000.0
4.6 (v) b (Double fold (CD))	750.0
4.6 (v) a (Double Fold (MD))	750.0
4.6 (Brightness, %)	2000.0
4.5 (pH (Hot Extract))	1000.0
4.6(viii) (Smoothness Bendsten)	2000.0
4.6 (vii) (Wax Pick)	2000.0
Firm's Requirement (Ash Content)	2000.0
Firm's Requirement (Resistance to Feathering)	1000.0
Firm's Requirement (Breaking Length (MD))	1000.0
Firm's Requirement (Breaking Length (CD))	1000.0
Firm's Requirement (Type of Pulp)	2000.0
Firm's Requirement (Color of Paper)	1000.0
Firm's Requirement (Surface Sizing)	1000.0
4.3 (Thickness)	1000.0
Firm's Requirement (Porosity (Gurley))	2000.0
Firm's Requirement (Yellowness)	1000.0
Firm's Requirement (L*)	500.0
Firm's Requirement (a*)	500.0
Firm's Requirement (b*)	500.0
Firm's Requirement (Bulk)	1000.0
4.4 (Sizes)	500.0
Firm's requirement (Moisture Content)	1000.0
4.6 (Test results - Annexure attached)	5000.0