NTH - Management Information System

National Test House (NR), Ghaziabad

Kamla Nehru Nagar, Ghaziabad, Uttar Pradesh - 201002, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

7003775955 nthnr-ca@nic.in

Scope List

Reset

571 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

361

CUSTOMER SPEC : EIL SOW & SPEC Vol 2 (Civil) P-4 - Etch Primer/Wash Primer

Etch Primer/Wash Primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 6.0 Table-2 (Please see Annexure)	40000.0

362

CUSTOMER SPEC : EIL SOW & SPEC Vol 2 (Civil)F-2 - Acrylic Polyurethane Finish Paint

Acrylic Polyurethane Finish Paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 6.0 Table-2 (Please see Annexure)	40000.0

363

CUSTOMER SPEC : EIL SOW & SPEC Vol 2 (Civil) F-3 - Chlorinated Rubber Based Finish paint

Chlorinated Rubber Based Finish paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 6.0 Table-2 (Please see Annexure)	40000.0

364

CUSTOMER SPEC : EIL SOW & SPEC Vol 2 (Civil) F-6A/B - Epoxy-High Build Coating

Epoxy-High Build Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 6.0 Table-2 (Please see Annexure)	40000.0

365

CUSTOMER SPEC : EIL SOW & SPEC Vol 2 (Civil) F-6C - Solvent less epoxy coating

Solvent less epoxy coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 6.0 Table-2 (Please see Annexure)	40000.0

366

CUSTOMER SPEC : EIL SOW & SPEC Vol 2 (Civil) P-6 - Epoxy Zinc Phosphate Primer

Epoxy Zinc Phosphate Primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 6.0 Table-2 (Please see Annexure)	40000.0

367

IS 1161 (2014) - Steel Tube for Structural Purposes

Steel Tube for Structural Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Outside Diameter)	500.0
6.1 (Thickness)	500.0
6.1 (Weight)	1000.0
7 (Workmanship)	1000.0
9 (Straightness)	1000.0
11.2 (Tensile Strength, MPa)	1000.0
11.2 (Yield strength, MPa)	1000.0
11.2 (Percent Elongation, %)	1000.0
11.3 (Cold Bend test)	-
11.3 (Bend Test / Flattening test)	1000.0
8 (Mass of Zinc Coating)	2000.0
0 (Coating Thickness, micron)	2000.0
0 (Uniformity of Coating)	1000.0
0 (Overall Length)	1000.0
0 (Adhesion test)	1000.0
0 (Salt Spray Test)	60000.0

368

RDSO SPEC M&C/PCN/103/2020 (2020) - SPECIFICATION FOR EPOXY BASED MICACEOUS IRON OXIDE (TWO- PACK)

SPECIFICATION FOR EPOXY BASED MICACEOUS IRON OXIDE (TWO- PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 3 & 4 (Table-I & II) (Please see Annexures (All physico mechanical & Chemical tests))	40000.0

369

IS 428 - Washable Distemper

Washable Distemper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl.6.5 Sr. No.(i) (Drying time)	1500.0

370

JIS K 5552:2010 (2010) - ZINC RICH PRIMER

ZINC RICH PRIMER

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 5 Table 1 (Please see Annexure)	25000.0

371

JIS K 5553 : 2002 (2002) - HIGH BUILD TYPE ZINC RICH PAINT

HIGH BUILD TYPE ZINC RICH PAINT

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 5 ,Table 1 (Please see Annexure)	30000.0

372

JIS K 5551:2008 (2008) - HEAVY DUTY ANTICORROSIVE PAINTS FOR METAL STRUCTURES

HEAVY DUTY ANTICORROSIVE PAINTS FOR METAL STRUCTURES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 5 Table 2 (Please see Annexure)	30000.0

373

IS 455 (2015) - Portland slag cement - Specification

Portland slag cement - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

374

Custom-4-NTH-LM - Omega Clamp/Profile Plate

Omega Clamp/Profile Plate

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Length)	500.0
2 (Width)	500.0
3 (Thickness)	500.0
4 (Weight)	1000.0
5 (Mass of Zinc Coating)	2000.0
6 (Uniformity of Coating)	1000.0
7 (Powder Coating Thickness)	1000.0
8 (Salt Spray Test for 1440 Hours)	72000.0

375

Custom-3-NTH-LM - Concertina coil/PTCC

Concertina coil/PTCC

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 (Carbon)	500.0
8 (Sulphur)	500.0
8 (Phosphorus)	500.0
8 (Chromium)	1000.0
8 (Manganese)	500.0
8 (Nickel)	500.0
8 (Silicon)	500.0
1 (Diameter of wire, mm)	1000.0
2 (Blade Length)	1000.0
3 (Center to center distance between blade)	1000.0
4 (Thickness of Blade)	1000.0
5 (Tensile Strength of wire)	3000.0
6 (Yield Stress of wire)	1000.0
7 (Percentage Elongation of wire)	1000.0
9 (Mass of Zinc Coating of wire)	1000.0
10 (Salt Spray Test for 1440 Hours)	72000.0
0 (Chemical Composition of Razor blade &wire(SS304))	6000.0
1 (Coil Diameter, mm)	1000.0

376

IS 7887 (1992) - Mild steel wire rod for general engineering purposes - Specification (First Revision)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Silicon)	2000.0
6.1 (Aluminium)	1000.0
6.1 (Phosphorus)	1000.0
6.1 (Sulphur)	1000.0
6.1 (Manganese)	1000.0
6.1 (Carbon)	1000.0
0 (Tensile strength, N/mm2)	1000.0
0 (Yield stress, N/mm2)	1000.0
0 (% Elongation)	1000.0

377

IS 432 : Part 2 (1982) - Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1.1 (Chemical Analysis (Sulphur))	500.0
3.1.1 (Chemical composition (Phosphorus))	500.0

378

IS 432 : Part 1 (1982) - Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Chemical composition)	2500.0
9.2 (Ultimate Tensile Stress)	1000.0
9.2 (Yield Strength)	1000.0
9.2 (% Elongation)	500.0
9.3 (Bend test)	1000.0

379

IS 319 (2007) - Free cutting brass bars, rods and section - Specification (Fifth Revision)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Zinc)	1200.0
8.1 (Iron)	1200.0
8.1 (Lead)	1200.0
8.1 (Copper)	1200.0
8.1 (Zinc)	1200.0
8.1 (Iron)	1200.0
8.1 (Lead)	1200.0
8.1 (Copper)	1200.0
Cl. 8.1 Table-1 (Grade-I or Grade-II) NABL (Cl. 8.1 Table -1 (Grade-I or Grade-II) (Pl. see Annexure)-NABL)	5000.0
Cl.no8.1,Table 1 (Chemical Composition( Please see the Annexure) NON NABL)	5000.0

380

IS 318 (1981) - Specification for leaded tin bronze ingots and castings (Second Revision)

Specification for leaded tin bronze ingots and castings (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 3 Chemical Composition (Chemical Analysis- (Please see Annexure - NON NABL))	2000.0
Table 3 Chemical Composition (Chemical Analysis- (Please see Annexure -NABL))	5000.0
0 (Hardness test)	2000.0

381

IS 278 (2009) - Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.2.1 (Zinc Coating of Line wire)	2000.0
6 (Chemical composition)	2500.0
12.1 (Breaking Load of Completed Barbed Wire)	1000.0
12.1 (Tensile Strength of Line Wire)	1000.0
5 (Dimension/ Sizes)	1000.0
9 (Freedom from Defects)	500.0

382

IS 21 (1992) - Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Chemical composition, Aluminium)	350.0
4.2 (Chemical composition, Copper)	350.0
4.2 (Chemical composition, Magnesium)	350.0
4.2 (Chemical composition, Silicon)	350.0
4.2 (Chemical composition, Iron)	350.0
4.2 (Chemical composition, Manganese)	350.0
4.2 (Chemical composition, Zinc)	350.0
4.2 (Chemical composition, Titanium)	350.0
4.2 (Chemical composition, Chromium)	350.0
4.2 (Chemical composition, Lead)	350.0
4.2 (Chemical composition, Cu+Mg+Si+Fe+Mn+Zn for Designation 19000)	-
4.2 (Chemical composition, Cu+Si+Fe+Mn+Zn for Designation 19500)	-
4.2 (Chemical composition, Cu+Mg+Si+Fe+Mn+Zn for Designation 19600)	-
4.2 (Chemical composition, % by mass)	3500.0

383

IS 13428 (2005) - Packaged Natural Mineral Water - Specification (Second Revision)

Packaged Natural Mineral Water - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.3 (Isoproturon)	5000.0

384

IS 3589 (2001) - Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Carbon)	500.0
9.2 (Flattening test)	1000.0
9.1 (Elongation)	1000.0
9.1 (Yield Strength)	1000.0
9.1 (Tensile Strength)	1000.0
12.5 (Straightness)	1000.0
14 (Visual Inspection, Apperance and Workman ship)	1000.0
11 (Weight)	1000.0
11 (Dimension (Diameter))	1000.0
11 (Thickness, mm)	1000.0
16.2 (Adhesion Test)	1000.0
6.1 (Uniformity of Zn Coating)	1000.0
3 (Mass of Zinc Coating)	2000.0
8.1 (Manganese)	1000.0
8.1 (Sulphur)	500.0
8.1 (Phosphorus)	500.0

385

Custom/Mech/2022 (2022) - Specification for Customer Test request.

Specification for Customer Test request.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Adhesion Test)	1000.0
0 (Coating Thickness)	2000.0
0 (Uniformity of Coating)	1000.0
0 (Mass of Zinc Coating)	2000.0
0 (Compression Test)	3000.0
0 (Chemical Composition)	4000.0
0 (Test results)	10000.0
0 (Breaking Load)	3000.0
0 (Percent Reduction of Area)	1000.0
0 (Microstructure analysis)	3000.0
0 (Impact test, J)	3000.0
C3 (Tensile Strength (MPa))	1000.0
C2 (Brinell/ Vickers/ Rockwell Hardness)	2000.0
M1 (Shear Strength test, MPa)	3000.0
8 (Dimensions)	2500.0
0 (Yield Stress/0.2% proof stress, MPa)	1000.0
0 (Proof Load)	3000.0
0 (Bend test)	1000.0
0 (Percent Elongation)	1000.0
0 (Yield Stress/0.2% proof stress, MPa)	1000.0
0 (Load test of Wedge on the lines of IS 14268)	3000.0
0 (Test results Chemical as per annexure)	10000.0
0 (Test results as per annexure)	61200.0
0 (Salt Spray test, 1440 Hrs.)	60000.0
0 (Tensile strength test, N/mm2)	5000.0
0 (Decarburization test)	3000.0
0 (Load Test)	5000.0
0 (Dimensions of Bolt Nut and washer)	2000.0
0 (Chemical Analysis(SS 304/SS 316) of Bolt, Nut and washers)	8000.0

386

IS 14930 : Part 1 (2001) - Conduit systems or electrical installations: Part 1 general requirements

Conduit systems or electrical installations: Part 1 general requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 (Dimensions)	2000.0
10.2 (Compression Test)	2000.0
10.3 (Impact Test)	2000.0

387

IS 1730 (1989) - Dimensions for steel plates,sheets strips and flats for general engineering purposes

Dimensions for steel plates,sheets strips and flats for general engineering purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Length of Cover Plate)	1000.0
5 (Thickness of Cover Plate)	1000.0
6 (Width of Cover Plate)	1000.0
7 (Thickness of Omega Clamp)	1000.0
4.2 (Width of Omega Clamp)	1000.0
4.3 (Length of Omega Clamp)	1000.0
9 (Mass of Zinc Coating)	2000.0
4.1 (Measurement of Dimensions)	2000.0
0 (Mass)	1000.0
0 (Chemical Composition)	3000.0
0 (Coating Thickness)	2000.0
0 (Uniformity of Coating)	1000.0
0 (Length)	1000.0
5.2 (Width)	1000.0
0 (Adhesion test)	1000.0
0 (Salt Spray Test, 1440 Hrs)	60000.0
5.1 (Thickness)	1000.0

388

IS 280 (2006) - Mild steel wire for general engineering purposes (Fourth Revision)

Mild steel wire for general engineering purposes (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2 (Wrapping Test)	1000.0
9.1 (Tensile Strength)	3000.0
0 (Mass of Zinc Coating)	2000.0
6 (Chemical composition)	2500.0
0 (Mass of Zinc Coating)	2000.0
0 (Uniformity of Coating)	1000.0
0 (Coating Thickness)	2000.0
0 (Weight)	1000.0
0 (Tensile Strength of Wire)	1000.0
0 (Weld Shear Strength)	3000.0
7.1 (Wire Diameter)	1000.0
7.1 (Wire Diameter)	1000.0
0 (Adhesion Test)	1000.0
13 (Freedom From Defects)	1000.0
0 (Salt Spray Test, 1000 hrs)	42000.0
0 (Dimension, mm)	1000.0
NA (Salt Spray Test, 1440 hrs)	57600.0
0 (Visual Examination)	1000.0

389

BSEH/OMR Sheet (2022) - Board of School Education-OMR Sheet

Board of School Education-OMR Sheet

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Grammage (GSM))	2000.0
2 (Size of OMR Sheet)	2520.0
3 (Perforation)	1500.0
4 (Numbering)	1500.0
5 (Stitching)	2000.0
6 (Color (Front Page))	2000.0
7 (Color (Back Page))	2000.0
8 (Bar Code Printing)	1500.0
9 (Time Bar Printing)	1500.0

390

BSEH/Answer Book (2022) - Board of School Education-Answer Book

Board of School Education-Answer Book

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Grammage of Inner Pages (GSM))	1000.0
2 (Tensile Index Machine Direction (Nm/g))	3000.0
3 (Tensile Index Cross Direction (Nm/g))	3000.0
4 (One Minute Cobb Test)	3000.0
5 (Brightness (%))	2000.0
6 (Opacity (%))	2000.0
7 (Number of Leaves)	2520.0