NTH - Management Information System

National Test House (NR), Ghaziabad

Kamla Nehru Nagar, Ghaziabad, Uttar Pradesh - 201002, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

7003775955 director-gzb[at]nth[dot]gov[dot]in

Scope List

Reset

616 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

241

IS 13757-1993 RA 2011 (1993 RA 2011) - Burnt Clay Fly Ash Building Bricks-specification

Burnt Clay Fly Ash Building Bricks-specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.0 Dimensions and Tolerances (Length, Width, Height mm)	1000.0
7.1 Compressive strength (Compressive strength)	2000.0
7.2 Water Absorption (Water absorption, %)	1000.0
7.3 Efflorescence (Efflorescence)	1000.0

242

ETI/OHE/50(6/97) re-designated to TI/SPC/OHE/CAT(Cu-Cd)/0971 (2021) - Technical specification for Cadmium copper conductors for over head Electric Traction

Technical specification for Cadmium copper conductors for over head Electric Traction

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.2.1 (Visual examination)	1000.0
8.2.2 (Chemical composition)	2000.0
8.2.3 (Measurement of diameter of individual wire and stranded conductor)	2000.0
8.2.4 (Measurement of weight of wire and conductor)	2000.0
8.2.5 (Measurement of lay length and lay ratio of each layer of stranded conductor)	5000.0
8.2.6 (Measurement of Electrical resistance of wire and stranded conductor)	15000.0
8.2.7 (Tensile test on wires)	32000.0
8.2.8 (Wrapping test on wires)	5000.0

243

ETI/OHE/76(6/97) - Technical specification for Hard Drawn Grooved Contact wire for Electric traction

Technical specification for Hard Drawn Grooved Contact wire for Electric traction

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Chemical Composition)	6000.0
8.5.1 (Visual Examination)	1000.0
8.5.2 (Measurement of Dimensions)	2000.0
8.5.3 (Compression Test)	3000.0
8.5.4 (Tensile Strength)	2000.0
8.5.4 (Elongation Test)	1000.0
8.5.6 (Micro-structure Examination)	3000.0
9.5.8 (Bending Test)	1000.0
9.5.6 (Brinell Hardness Test)	1.0
9.5.10 (Electrical Resistance Test)	2000.0
9.5.5 (Measurement of Weight)	1000.0

244

TI/SPC/OHE/CAT (Cu-Mg)/0150 (2016) - Hard drawn stranded Magnesium Copper Conductors

Hard drawn stranded Magnesium Copper Conductors

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Copper Content, % by Mass)	1000.0
5.1 (Magnesium Content, % by Mass)	1000.0
5.1 (Chemical composition, % by Mass)	5000.0
12.2 (Diameter, mm)	1000.0
Weight per Kilometre (Weight per Kilometre, kg)	1000.0
12.2 (Resistance per km at 20 deg. C)	2000.0
12.2 (Breaking load of individual wire)	19000.0
12.2 (Tensile strength of wire)	3000.0
0 (Lay length and Lay ratio)	1000.0
0 (Wrapping test)	1000.0

245

IS 13498- 2017 (2017) - BATHING BAR SPECIFICATION (for NR)

BATHING BAR SPECIFICATION (for NR)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clauses 5.1, 7.3 and 8.1, Table 1 (Please see the annexure.)	10000.0

246

IS 7884 (2023) - Shampoo - Specification

Shampoo - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
CL-3.4, Table 1 (Please see Annexure.)	8000.0

247

IS 13114 (1991) - forged brass gate, globe and check valves for water works purposes

forged brass gate, globe and check valves for water works purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Dimensions)	1000.0
9.2 (Materials)	2000.0
9.3 (Shell Test (Hydrostatic Test))	2500.0
9.3 (Seat & Backseat Test (Hydrostatic Test))	2500.0

248

IS 13095 (2020) - Butterfly Valves for General Purposes ( First Revision )

Butterfly Valves for General Purposes ( First Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10 (Face to Face Dimensions)	1000.0
17.2 (Hydrostatic Test of Body)	2500.0
17.3 (Hydrostatic Test of Seat)	2500.0
15 (Materials)	2000.0
17.4 (Hydrostatic Test of Disc Strength)	2500.0
17.1 (Performance Test)	5000.0

249

IS 1065 : Part 1 (2019) - Stable bleaching powder - Specification: Part 1 household and industrial use (Third Revision)

Stable bleaching powder - Specification: Part 1 household and industrial use (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.3 (Available Chlorine)	2500.0

250

IS 13213 (2018) - Polyurethane full gloss enamel (Two Pack) - Specification (First Revision)

Polyurethane full gloss enamel (Two Pack) - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 1 Table 1 (Please see Annexure (All possible Tests))	60000.0
Cl 1 Table 1 (Please see Annexure Durability ( Outdoor exposure only) + Keeping properties)	30000.0

251

IS 14946 (2001) - Zinc ethyl silicate primer, two components - Specification

Zinc ethyl silicate primer, two components - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 1 Table 1 (Please see Annexure (All possible tests))	90000.0
Cl 1 Table 1 (Please see Annexure for Salt spray & Protection against corrosion test)	70000.0

252

IS 13213 (2018) - Polyurethane Full Gloss Enamel (Two Pack) — Specification

Polyurethane Full Gloss Enamel (Two Pack) — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Polyurethane Full Gloss Enamel (Two Pack) — Specification (Please refer annexure for tests result)	46000.0

253

NTH/NR/RPPT/HDPE Membrane (2023) - HDPE Membrane for Waterproofing

HDPE Membrane for Waterproofing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's Requirement (Puncture Resistance)	3000.0
Firm's Requirement (Tensile Strength)	1500.0
Firm's Requirement (Elongation)	1500.0
Firm's Requirement (Peel Adhesion to Concrete)	3000.0
Firm's Requirement (Thickness)	1000.0
Firm's Requirement (Lap Adhesion)	2000.0

254

IS 1776 (1989) - Folding box board, uncoated - Specification (First Revision)

Folding box board, uncoated - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Substance (Grammage))	1000.0
Table 1 (Burst Index)	2000.0
Table-1 (pH (both sides))	1000.0
Table-1 (Ash Content)	2000.0
Table-1 (One Minute Cobb Test (Front))	2000.0
Table-1 (One Minute Cobb Test (Back))	2000.0
Table-1 (Moisture Content (As received))	1000.0
Table-1 (Brightness of White Boards, Front Side only)	2000.0
Table-1 (Stiffness Factor)	1000.0
Table-1 (Wax Pick (Front))	2000.0
Table-1 (Wax Pick (Back))	2000.0
Table-1 (Smoothness)	2000.0

255

Custom/Civil/Misc/2023-24 - .

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Rebound Hammer per segment)	1500.0
3 (Scientists charge)	10000.0
1 (Hardness of Stone)	1000.0
2 (Dimensions of Sanitary Fittings)	2000.0
5 (Thickness of Board)	1000.0
6 (Thickness of Laminate of Board)	1000.0
7 (Thickness of Board with Laminate)	1000.0
- (Vetting of Specification-consultancy)	10000.0

256

IS 2508 (2016) - Low Density Polyethylene Films

Low Density Polyethylene Films

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Thickness)	4000.0

257

IS 516 : Part 5 : Sec 4 (2020) - Hardened Concrete Methods of Test Part 5 Non-Destructive Testing of Concrete Section 4 Rebound Hammer Test ( First Revision )

Hardened Concrete Methods of Test Part 5 Non-Destructive Testing of Concrete Section 4 Rebound Hammer Test ( First Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Rebound hammer test (field test))	15000.0
- - (Scientist charges (2 Scientists) for site testing / inspection)	10000.0
- (Rebound Hammer test)	3000.0

258

IS:309-2005 - COMPRESSED OXYGEN GAS — SPECIFICATION

COMPRESSED OXYGEN GAS — SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
CLAUSE-4,Table-1 (Purity of compressed oxygen gas)	3000.0
CLAUSE-4,Table-1 (DEW POINT)	2000.0
CLAUSE-4,Table-1 (Volume Fraction of Carbonmonoxide and Carbondioxide)	2000.0
CLAUSE-4,Table-1 (Volume Fraction of Hydrocarbons)	2000.0

259

IS 341 (2016) - Black japan, types a, b and c - Specification (Second Revision)

Black japan, types a, b and c - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
x) (Keeping properties)	5000.0
ix) (Flash point)	1200.0
viii) (Resistance to heat (for 2 h) (for Type C))	1200.0
vii) (Resistance to kerosene for Types B and C))	1500.0
vi) (Stripping test)	1200.0
b) (Scratch hardness (load 1 000g))	1500.0
a) (Bend test (with 6.25 mm dia mandrel and in type 1 apparatus))	1500.0
iv) (Ash content percent by mass)	1200.0
iii) (Volatile matter content, percent by mass, Max)	2000.0
ii) (Finish)	1200.0
5.6 Table i) b) (b) Hard dry)	1500.0
5.6 Table i) a) (a) surface dry)	1200.0
5.6 Table i) (Drying time)	1500.0
5.5 (Durability)	8000.0
5.4 (Lead Restriction)	2500.0
5.3 (Reaction with Varnish, Exterior)	1200.0
5.2 (Reaction with White Paint)	1000.0
5.1 (Composition)	2000.0

260

IS 5206 (1983) - Specification for covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels (First Revision)

Specification for covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2 (Tensile Strength)	2000.0
9.2 (Elongation)	1000.0
9.2 (preparation of Butt Weld assembly)	4000.0
5.3 (Length of Electrodes)	500.0
6.1 (Bare Length-Contact End)	500.0
6.2 (Bare Length-Arc stricking end)	500.0
6.3 (Flux Covering)	500.0
9.1 (Copper)	500.0
9.1 (Molybdenum)	500.0
9.1 (Chromium)	500.0
9.1 (Nickel)	500.0
9.1 (Phosphorus)	500.0
9.1 (Sulphur)	500.0
9.1 (Manganese)	500.0
9.1 (Silicon)	500.0
9.1 (Carbon)	500.0
9.3 (preparation of Fillet weld assembly)	3000.0
1 (Macro examination)	1000.0
0 (Preparation of Weld piece)	3000.0

261

Custom/NDT/NR - -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

262

AWS specification - Specification for Fracture Test

Specification for Fracture Test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Fracture Test)	9000.0

263

Fastener as per ISO/EN/BS EN - Mechanical properties of Fastener as per ISO 898 (Part- 1, 2), EN 14399 (P-3,5,9), ISO 10683

Mechanical properties of Fastener as per ISO 898 (Part- 1, 2), EN 14399 (P-3,5,9), ISO 10683

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Proof Load, kN)	3000.0
7.2 (Hardness)	2000.0
7.3 (Surface Integrity)	2000.0
7.4 (Depth of Decarburisation)	2000.0
7.5 (Coating Thickness, micron)	2000.0
7.6 (Adhesion test)	1000.0
6 (Chemical composition, % by mass)	2500.0
5.1 (Wedge Load Test)	3000.0
5.2 (Tensile test- TS, YS, %E and RoA)	4000.0
5.4 (Charpy Impact Test, At -20 deg C)	3000.0
5.5 (Compression load Test)	3000.0
5.5 (Dimensions, mm)	2000.0

264

IS 9862 (2017) - Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision)

Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Lead Restriction as metallic lead)	1500.0
4.3 table 1(i) (Drying time a) Hard dry)	1500.0
4.3 table 1(ii) (Consistency)	1000.0
4.3 table 1(iii) (Finish)	500.0
4.3 table 1(iv) (Wet opacity meter square per liter)	500.0
4.3 table 1(v) (Mass, kg/10 Litres,)	1000.0
4.3 table 1(vi) (Colour)	200.0
4.3 table 1(vii) (Flexibility and adhesion (bend test of the film with 6.25 dia Mandrel in type 1 apparatus))	1000.0
4.3 table 1(viii) (Stripping test ( By scratch hardness tester))	1000.0
4.3 table 1(ix) (Flash point deg.C)	1000.0
4.3 table 1(x) (Volatile matter content, percent by mass,)	1000.0
4.3 table 1(xi) (Resistance to humidity under conditions of condensation)	2000.0
4.3 table 1(xii) (Resistance to water)	1000.0
4.3 table 1(xiii) (Resistance to acid (Dilute Sulphuric Acid 1: 20 (v/v))	1500.0
4.3 table 1(xiv) (Resistance to alkali (Sodium Carbonate 5 % m/v Solution))	1500.0
4.3 table 1(xv) (Resistance to chlorine (0.05 percent of chlorine (m/v).)	1000.0
4.3 table 1(xvi) (Water content (if water is suspected to be present), percent by mass,)	1500.0
4.3 table 1(xvii) (Keeping properties(12 Months))	5000.0

265

TI/SPC/OHE/CAT(Cd-Cu)/0971 - Technical specification for Cadmium Copper for Overhead Electrical Traction

Technical specification for Cadmium Copper for Overhead Electrical Traction

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1.1 (Chemical composition, percent by mass)	5000.0
8.3.5 (Electrical Resistance)	5000.0
4.8 (Mass, kg/m)	1000.0
8.3.2 (Measurement of diameter, mm)	2000.0
8.3.4 (Lay length and Lay ratio, mm)	3000.0
8.3.6 (Tensile strength for individual 19 wires)	9500.0
8.3.7 (Wrapping test)	1000.0
9.1.1 (Visual examination)	1000.0
9.1.2 (Diameter of Stranded conductor)	1000.0

266

IS 4020(Parts 1 to 16):1998 RA 2018 - Door shutters-Methods of Tests

Door shutters-Methods of Tests

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2-2.1 (Dimension: Height(mm) (IS 4020 (part 2) : 1998))	250.0
2-2.2 (Dimension:Width (IS 4020 (part 2) : 1998))	250.0
2-2.3 (Diemension:Thickness (IS 4020 (part 2) : 1998))	250.0
10 (Slamming Test (IS 4020 (part 10) : 1998))	1000.0
8 (Shock resistance Test (IS 4020 (part 8) : 1998))	1500.0
7 (Edge Loading Test ( IS 4020 (part 7) : 1998))	1500.0

267

IS 2645:2003 (RA 2017) - Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.4 (Chloride content)	2000.0
- (pH)	1000.0

268

IRC 137-2022 (2022) - Guideline on use of Fibre-reinforced polymer bars in road projects

Guideline on use of Fibre-reinforced polymer bars in road projects

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.2.5.1 (Mean measured cross sectional area ASTM D7205)	1000.0
4.1 (Guaranteed Ultimate tensile strength, ASTM D 7205)	3000.0
0 (Mean Tensile Modulus of Elasticity, ASTM D 7205)	2000.0
4.1 (Mean Ultimate Tensile Strain, ASTM D 7205)	3000.0
0 (Guuaranteed Transeverse Shear Strength, ASTM D 7617)	5000.0
0 (Guuaranteed Bond Strength, ASTM D 7913)	10000.0
0 (Mean moisture Absorption to Saturation, ASTM D570)	1000.0

269

Cable tray - Cable tray

Cable tray

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension Tests)	1000.0
2 (Thickness Test)	1000.0
3 (Perforation area)	1000.0
4 (Galvanization Thickness Test)	2000.0
5 (Load Test with applying 1.7 times SWL)	3000.0
6 (Material Composition Test)	3000.0
2 (Salt Spray Test, 24 hours)	960.0

270

Junction Box - Junction Box

Junction Box

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimensional Tests)	1000.0
2 (Thickness Test)	1000.0
3 (Mass of Zinc Coating)	2000.0
4 (Vertical Load Test)	3000.0