| 151 |
NTH/NR/RPPT/2023/Sealant Component-B/01 (2023) - Sealant Component-B |
Sealant Component-B |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| ASTM D 792 (Relative Density) |
2000.0 |
|
| ASTM D 2240 (Hardness, Shore D) |
1000.0 |
|
| ASTM D 1002 (Lap Shear Strength) |
3000.0 |
|
| ASTM D 695 (Compression Strength) |
3000.0 |
|
| ASTM D 638 (Tensile Strength) |
3000.0 |
|
| Firm's Requirement (Full Cure, Maximum) |
1000.0 |
|
| NCD 1410 (Critical Oxygen Index) |
5000.0 |
|
| NCD 1411 (Smoke Index) |
10000.0 |
|
| On the lines of BS 476 Part-7 (Fire Test) |
8000.0 |
|
|
| 152 |
NTH/NR/RPPT/2023/Filler Component-A/01 (2023) - Filler Component-A |
Filler Component-A |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| ASTM D 1084 (Viscosity of the Mixture) |
2000.0 |
|
| Firm's Requirement (Full Cure, Maximum) |
1000.0 |
|
| Firm's Requirement (Expansion, Minimum) |
3000.0 |
|
| Firm's Requirement (Critical Oxygen Index (After curing of the compound)) |
5000.0 |
|
| Firm's Requirement (Smoke Index (After curing of the compound)) |
10000.0 |
|
| On the lines of BS 476 Part-7 (Fire Test) |
8000.0 |
|
|
| 153 |
IS 13757-1993 RA 2011 (1993 RA 2011) - Burnt Clay Fly Ash Building Bricks-specification |
Burnt Clay Fly Ash Building Bricks-specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.0 Dimensions and Tolerances (Length, Width, Height mm) |
1000.0 |
|
| 7.1 Compressive strength (Compressive strength) |
2000.0 |
|
| 7.2 Water Absorption (Water absorption, %) |
1000.0 |
|
| 7.3 Efflorescence (Efflorescence) |
1000.0 |
|
|
| 154 |
ETI/OHE/50(6/97) re-designated to TI/SPC/OHE/CAT(Cu-Cd)/0971 (2021) - Technical specification for Cadmium copper conductors for over head Electric Traction |
Technical specification for Cadmium copper conductors for over head Electric Traction |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8.2.1 (Visual examination) |
1000.0 |
|
| 8.2.2 (Chemical composition) |
2000.0 |
|
| 8.2.3 (Measurement of diameter of individual wire and stranded conductor) |
2000.0 |
|
| 8.2.4 (Measurement of weight of wire and conductor) |
2000.0 |
|
| 8.2.5 (Measurement of lay length and lay ratio of each layer of stranded conductor) |
5000.0 |
|
| 8.2.6 (Measurement of Electrical resistance of wire and stranded conductor) |
15000.0 |
|
| 8.2.7 (Tensile test on wires) |
32000.0 |
|
| 8.2.8 (Wrapping test on wires) |
5000.0 |
|
|
| 155 |
ETI/OHE/76(6/97) - Technical specification for Hard Drawn Grooved Contact wire for Electric traction |
Technical specification for Hard Drawn Grooved Contact wire for Electric traction |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.1 (Chemical Composition) |
6000.0 |
|
| 8.5.1 (Visual Examination) |
1000.0 |
|
| 8.5.2 (Measurement of Dimensions) |
2000.0 |
|
| 8.5.3 (Compression Test) |
3000.0 |
|
| 8.5.4 (Tensile Strength) |
2000.0 |
|
| 8.5.4 (Elongation Test) |
1000.0 |
|
| 8.5.6 (Micro-structure Examination) |
3000.0 |
|
| 9.5.8 (Bending Test) |
1000.0 |
|
| 9.5.6 (Brinell Hardness Test) |
1.0 |
|
| 9.5.10 (Electrical Resistance Test) |
2000.0 |
|
| 9.5.5 (Measurement of Weight) |
1000.0 |
|
|
| 156 |
TI/SPC/OHE/CAT (Cu-Mg)/0150 (2016) - Hard drawn stranded Magnesium Copper Conductors |
Hard drawn stranded Magnesium Copper Conductors |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5.1 (Copper Content, % by Mass) |
1000.0 |
|
| 5.1 (Magnesium Content, % by Mass) |
1000.0 |
|
| 5.1 (Chemical composition, % by Mass) |
5000.0 |
|
| 12.2 (Diameter, mm) |
1000.0 |
|
| Weight per Kilometre (Weight per Kilometre, kg) |
1000.0 |
|
| 12.2 (Resistance per km at 20 deg. C) |
2000.0 |
|
| 12.2 (Breaking load of individual wire) |
19000.0 |
|
| 12.2 (Tensile strength of wire) |
3000.0 |
|
| 0 (Lay length and Lay ratio) |
1000.0 |
|
| 0 (Wrapping test) |
1000.0 |
|
|
| 157 |
IS 13498- 2017 (2017) - BATHING BAR SPECIFICATION (for NR) |
BATHING BAR SPECIFICATION (for NR) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Clauses 5.1, 7.3 and 8.1, Table 1 (Please see the annexure.) |
10000.0 |
|
|
| 158 |
IS 7884 (2023) - Shampoo - Specification |
Shampoo - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| CL-3.4, Table 1 (Please see Annexure.) |
8000.0 |
|
|
| 159 |
IS 13114 (1991) - forged brass gate, globe and check valves for water works purposes |
forged brass gate, globe and check valves for water works purposes |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7 (Dimensions) |
1000.0 |
|
| 9.2 (Materials) |
2000.0 |
|
| 9.3 (Shell Test (Hydrostatic Test)) |
2500.0 |
|
| 9.3 (Seat & Backseat Test (Hydrostatic Test)) |
2500.0 |
|
|
| 160 |
IS 13095 (2020) - Butterfly Valves for General Purposes ( First Revision ) |
Butterfly Valves for General Purposes ( First Revision ) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 10 (Face to Face Dimensions) |
1000.0 |
|
| 17.2 (Hydrostatic Test of Body) |
2500.0 |
|
| 17.3 (Hydrostatic Test of Seat) |
2500.0 |
|
| 15 (Materials) |
2000.0 |
|
| 17.4 (Hydrostatic Test of Disc Strength) |
2500.0 |
|
| 17.1 (Performance Test) |
5000.0 |
|
|
| 161 |
IS 1065 : Part 1 (2019) - Stable bleaching powder - Specification: Part 1 household and industrial use (Third Revision) |
Stable bleaching powder - Specification: Part 1 household and industrial use (Third Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5.3 (Available Chlorine) |
2500.0 |
|
|
| 162 |
IS 13213 (2018) - Polyurethane full gloss enamel (Two Pack) - Specification (First Revision) |
Polyurethane full gloss enamel (Two Pack) - Specification (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Cl 1 Table 1 (Please see Annexure (All possible Tests)) |
60000.0 |
|
| Cl 1 Table 1 (Please see Annexure Durability ( Outdoor exposure only) + Keeping properties) |
30000.0 |
|
|
| 163 |
IS 14946 (2001) - Zinc ethyl silicate primer, two components - Specification |
Zinc ethyl silicate primer, two components - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Cl 1 Table 1 (Please see Annexure (All possible tests)) |
90000.0 |
|
| Cl 1 Table 1 (Please see Annexure for Salt spray & Protection against corrosion test) |
70000.0 |
|
|
| 164 |
IS 13213 (2018) - Polyurethane Full Gloss Enamel (Two Pack) — Specification |
Polyurethane Full Gloss Enamel (Two Pack) — Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Polyurethane Full Gloss Enamel (Two Pack) — Specification (Please refer annexure for tests result) |
46000.0 |
|
|
| 165 |
NTH/NR/RPPT/HDPE Membrane (2023) - HDPE Membrane for Waterproofing |
HDPE Membrane for Waterproofing |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Firm's Requirement (Puncture Resistance) |
3000.0 |
|
| Firm's Requirement (Tensile Strength) |
2000.0 |
|
| Firm's Requirement (Elongation) |
2000.0 |
|
| Firm's Requirement (Peel Adhesion to Concrete) |
3000.0 |
|
|
| 166 |
IS 1776 (1989) - Folding box board, uncoated - Specification (First Revision) |
Folding box board, uncoated - Specification (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5.2 (Substance (Grammage)) |
1000.0 |
|
| Table 1 (Burst Index) |
2000.0 |
|
| Table-1 (pH (both sides)) |
1000.0 |
|
| Table-1 (Ash Content) |
2000.0 |
|
| Table-1 (One Minute Cobb Test (Front)) |
2000.0 |
|
| Table-1 (One Minute Cobb Test (Back)) |
2000.0 |
|
| Table-1 (Moisture Content (As received)) |
1000.0 |
|
| Table-1 (Brightness of White Boards, Front Side only) |
2000.0 |
|
| Table-1 (Stiffness Factor) |
1000.0 |
|
| Table-1 (Wax Pick (Front)) |
2000.0 |
|
| Table-1 (Wax Pick (Back)) |
2000.0 |
|
| Table-1 (Smoothness) |
2000.0 |
|
|
| 167 |
Custom/Civil/Misc/2023-24 - . |
. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4 (Rebound Hammer per segment) |
1500.0 |
|
| 3 (Scientists charge) |
10000.0 |
|
| 1 (Hardness of Stone) |
1000.0 |
|
| 2 (Dimensions of Sanitary Fittings) |
2000.0 |
|
| 5 (Thickness of Board) |
1000.0 |
|
| 6 (Thickness of Laminate of Board) |
1000.0 |
|
| 7 (Thickness of Board with Laminate) |
1000.0 |
|
| - (Vetting of Specification-consultancy) |
10000.0 |
|
|
| 168 |
IS 2508 (2016) - Low Density Polyethylene Films |
Low Density Polyethylene Films |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5.2 (Thickness) |
4000.0 |
|
|
| 169 |
IS 516 : Part 5 : Sec 4 (2020) - Hardened Concrete Methods of Test Part 5 Non-Destructive Testing of Concrete Section 4 Rebound Hammer Test ( First Revision ) |
Hardened Concrete Methods of Test Part 5 Non-Destructive Testing of Concrete Section 4 Rebound Hammer Test ( First Revision ) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 0 (Rebound hammer test (field test) -per Ten locations) |
15000.0 |
|
| - - (Scientist charges (2 Scientists) for site testing / inspection) |
10000.0 |
|
| - (Rebound Hammer test) |
3000.0 |
|
|
| 170 |
IS:309-2005 - COMPRESSED OXYGEN GAS — SPECIFICATION |
COMPRESSED OXYGEN GAS — SPECIFICATION |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| CLAUSE-4,Table-1 (Purity of compressed oxygen gas) |
4000.0 |
|
| CLAUSE-4,Table-1 (DEW POINT) |
2000.0 |
|
| CLAUSE-4,Table-1 (Volume Fraction of Carbonmonoxide and Carbondioxide) |
2000.0 |
|
| CLAUSE-4,Table-1 (Volume Fraction of Hydrocarbons) |
2000.0 |
|
|
| 171 |
IS 341 (2016) - Black japan, types a, b and c - Specification (Second Revision) |
Black japan, types a, b and c - Specification (Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| x) (Keeping properties) |
5000.0 |
|
| ix) (Flash point) |
1200.0 |
|
| viii) (Resistance to heat (for 2 h) (for Type C)) |
1200.0 |
|
| vii) (Resistance to kerosene for Types B and C)) |
1500.0 |
|
| vi) (Stripping test) |
1200.0 |
|
| b) (Scratch hardness (load 1 000g)) |
1500.0 |
|
| a) (Bend test (with 6.25 mm dia mandrel and in type 1 apparatus)) |
1500.0 |
|
| iv) (Ash content percent by mass) |
1200.0 |
|
| iii) (Volatile matter content, percent by mass, Max) |
2000.0 |
|
| ii) (Finish) |
1200.0 |
|
| 5.6 Table i) b) (b) Hard dry) |
1500.0 |
|
| 5.6 Table i) a) (a) surface dry) |
1200.0 |
|
| 5.6 Table i) (Drying time) |
1500.0 |
|
| 5.5 (Durability) |
8000.0 |
|
| 5.4 (Lead Restriction) |
2500.0 |
|
| 5.3 (Reaction with Varnish, Exterior) |
1200.0 |
|
| 5.2 (Reaction with White Paint) |
1000.0 |
|
| 5.1 (Composition) |
2000.0 |
|
|
| 172 |
IS 5206 (1983) - Specification for covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels (First Revision) |
Specification for covered electrodes for manual metal arc welding of stainless steel and other similar high alloy steels (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 9.2 (Tensile Strength) |
2000.0 |
|
| 9.2 (Elongation) |
1000.0 |
|
| 9.2 (preparation of Butt Weld assembly) |
4000.0 |
|
| 5.3 (Length of Electrodes) |
500.0 |
|
| 6.1 (Bare Length-Contact End) |
500.0 |
|
| 6.2 (Bare Length-Arc stricking end) |
500.0 |
|
| 6.3 (Flux Covering) |
500.0 |
|
| 9.1 (Copper) |
500.0 |
|
| 9.1 (Molybdenum) |
500.0 |
|
| 9.1 (Chromium) |
500.0 |
|
| 9.1 (Nickel) |
500.0 |
|
| 9.1 (Phosphorus) |
500.0 |
|
| 9.1 (Sulphur) |
500.0 |
|
| 9.1 (Manganese) |
500.0 |
|
| 9.1 (Silicon) |
500.0 |
|
| 9.1 (Carbon) |
500.0 |
|
| 9.3 (preparation of Fillet weld assembly) |
3000.0 |
|
| 1 (Macro examination) |
1000.0 |
|
| 0 (Preparation of Weld piece) |
3000.0 |
|
|
| 173 |
Custom/NDT/NR - - |
- |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 174 |
AWS specification - Specification for Fracture Test |
Specification for Fracture Test |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Fracture Test) |
9000.0 |
|
|
| 175 |
Fastener as per ISO/EN/BS EN - Mechanical properties of Fastener as per ISO 898 (Part- 1, 2), EN 14399 (P-3,5,9), ISO 10683 |
Mechanical properties of Fastener as per ISO 898 (Part- 1, 2), EN 14399 (P-3,5,9), ISO 10683 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7.1 (Proof Load, kN) |
3000.0 |
|
| 7.2 (Hardness) |
2000.0 |
|
| 7.3 (Surface Integrity) |
2000.0 |
|
| 7.4 (Depth of Decarburisation) |
2000.0 |
|
| 7.5 (Coating Thickness, micron) |
2000.0 |
|
| 7.6 (Adhesion test) |
1000.0 |
|
| 6 (Chemical composition, % by mass) |
2500.0 |
|
| 5.1 (Wedge Load Test) |
3000.0 |
|
| 5.2 (Tensile test- TS, YS, %E and RoA) |
4000.0 |
|
| 5.4 (Charpy Impact Test, At -20 deg C) |
3000.0 |
|
| 5.5 (Compression load Test) |
3000.0 |
|
| 5.5 (Dimensions, mm) |
2000.0 |
|
|
| 176 |
IS 9862 (2017) - Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision) |
Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.2 (Lead Restriction as metallic lead) |
1500.0 |
|
| 4.3 table 1(i) (Drying time a) Hard dry) |
1500.0 |
|
| 4.3 table 1(ii) (Consistency) |
1000.0 |
|
| 4.3 table 1(iii) (Finish) |
500.0 |
|
| 4.3 table 1(iv) (Wet opacity meter square per liter) |
500.0 |
|
| 4.3 table 1(v) (Mass, kg/10 Litres,) |
1000.0 |
|
| 4.3 table 1(vi) (Colour) |
200.0 |
|
| 4.3 table 1(vii) (Flexibility and adhesion (bend test of the film with 6.25 dia Mandrel in type 1 apparatus)) |
1000.0 |
|
| 4.3 table 1(viii) (Stripping test ( By scratch hardness tester)) |
1000.0 |
|
| 4.3 table 1(ix) (Flash point deg.C) |
1000.0 |
|
| 4.3 table 1(x) (Volatile matter content, percent by mass,) |
1000.0 |
|
| 4.3 table 1(xi) (Resistance to humidity under conditions of condensation) |
2000.0 |
|
| 4.3 table 1(xii) (Resistance to water) |
1000.0 |
|
| 4.3 table 1(xiii) (Resistance to acid (Dilute Sulphuric Acid 1: 20 (v/v)) |
1500.0 |
|
| 4.3 table 1(xiv) (Resistance to alkali (Sodium Carbonate 5 % m/v Solution)) |
1500.0 |
|
| 4.3 table 1(xv) (Resistance to chlorine
(0.05 percent of chlorine (m/v).) |
1000.0 |
|
| 4.3 table 1(xvi) (Water content (if water is suspected to be present), percent by mass,) |
1500.0 |
|
| 4.3 table 1(xvii) (Keeping properties(12 Months)) |
5000.0 |
|
|
| 177 |
TI/SPC/OHE/CAT(Cd-Cu)/0971 - Technical specification for Cadmium Copper for Overhead Electrical Traction |
Technical specification for Cadmium Copper for Overhead Electrical Traction |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.1.1 (Chemical composition, percent by mass) |
5000.0 |
|
| 8.3.5 (Electrical Resistance) |
5000.0 |
|
| 4.8 (Mass, kg/m) |
1000.0 |
|
| 8.3.2 (Measurement of diameter, mm) |
2000.0 |
|
| 8.3.4 (Lay length and Lay ratio, mm) |
3000.0 |
|
| 8.3.6 (Tensile strength for individual 19 wires) |
9500.0 |
|
| 8.3.7 (Wrapping test) |
1000.0 |
|
| 9.1.1 (Visual examination) |
1000.0 |
|
| 9.1.2 (Diameter of Stranded conductor) |
1000.0 |
|
|
| 178 |
IS 4020(Parts 1 to 16):1998 RA 2018 - Door shutters-Methods of Tests |
Door shutters-Methods of Tests |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 2-2.1 (Dimension: Height(mm) (IS 4020 (part 2) : 1998)) |
250.0 |
|
| 2-2.2 (Dimension:Width (IS 4020 (part 2) : 1998)) |
250.0 |
|
| 2-2.3 (Diemension:Thickness (IS 4020 (part 2) : 1998)) |
250.0 |
|
| 10 (Slamming Test (IS 4020 (part 10) : 1998)) |
1000.0 |
|
| 8 (Shock resistance Test (IS 4020 (part 8) : 1998)) |
1500.0 |
|
| 7 (Edge Loading Test ( IS 4020 (part 7) : 1998)) |
1500.0 |
|
|
| 179 |
IS 2645:2003 (RA 2017) - Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification |
Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.4 (Chloride content) |
2000.0 |
|
| - (pH) |
1000.0 |
|
|
| 180 |
IRC 137-2022 (2022) - Guideline on use of Fibre-reinforced polymer bars in road projects |
Guideline on use of Fibre-reinforced polymer bars in road projects |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 11.2.5.1 (Mean measured cross sectional area ASTM D7205) |
1000.0 |
|
| 4.1 (Guaranteed Ultimate tensile strength, ASTM D 7205) |
3000.0 |
|
| 0 (Mean Tensile Modulus of Elasticity, ASTM D 7205) |
2000.0 |
|
| 4.1 (Mean Ultimate Tensile Strain, ASTM D 7205) |
3000.0 |
|
| 0 (Guuaranteed Transeverse Shear Strength, ASTM D 7617) |
5000.0 |
|
| 0 (Guuaranteed Bond Strength, ASTM D 7913) |
10000.0 |
|
| 0 (Mean moisture Absorption to Saturation, ASTM D570) |
1000.0 |
|
|
