| 121 |
IS 9862 (2017) - Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision) |
Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.2 (Lead Restriction as metallic lead) |
1500.0 |
|
| 4.3 table 1(i) (Drying time a) Hard dry) |
1500.0 |
|
| 4.3 table 1(ii) (Consistency) |
1000.0 |
|
| 4.3 table 1(iii) (Finish) |
500.0 |
|
| 4.3 table 1(iv) (Wet opacity meter square per liter) |
500.0 |
|
| 4.3 table 1(v) (Mass, kg/10 Litres,) |
1000.0 |
|
| 4.3 table 1(vi) (Colour) |
200.0 |
|
| 4.3 table 1(vii) (Flexibility and adhesion (bend test of the film with 6.25 dia Mandrel in type 1 apparatus)) |
1000.0 |
|
| 4.3 table 1(viii) (Stripping test ( By scratch hardness tester)) |
1000.0 |
|
| 4.3 table 1(ix) (Flash point deg.C) |
1000.0 |
|
| 4.3 table 1(x) (Volatile matter content, percent by mass,) |
1000.0 |
|
| 4.3 table 1(xi) (Resistance to humidity under conditions of condensation) |
2000.0 |
|
| 4.3 table 1(xii) (Resistance to water) |
1000.0 |
|
| 4.3 table 1(xiii) (Resistance to acid (Dilute Sulphuric Acid 1: 20 (v/v)) |
1500.0 |
|
| 4.3 table 1(xiv) (Resistance to alkali (Sodium Carbonate 5 % m/v Solution)) |
1500.0 |
|
| 4.3 table 1(xv) (Resistance to chlorine
(0.05 percent of chlorine (m/v).) |
1000.0 |
|
| 4.3 table 1(xvi) (Water content (if water is suspected to be present), percent by mass,) |
1500.0 |
|
| 4.3 table 1(xvii) (Keeping properties(12 Months)) |
5000.0 |
|
|
| 122 |
TI/SPC/OHE/CAT(Cd-Cu)/0971 - Technical specification for Cadmium Copper for Overhead Electrical Traction |
Technical specification for Cadmium Copper for Overhead Electrical Traction |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.1.1 (Chemical composition, percent by mass) |
5000.0 |
|
| 8.3.5 (Electrical Resistance) |
5000.0 |
|
| 4.8 (Mass, kg/m) |
1000.0 |
|
| 8.3.2 (Measurement of diameter, mm) |
2000.0 |
|
| 8.3.4 (Lay length and Lay ratio, mm) |
3000.0 |
|
| 8.3.6 (Tensile strength for individual 19 wires) |
9500.0 |
|
| 8.3.7 (Wrapping test) |
1000.0 |
|
| 9.1.1 (Visual examination) |
1000.0 |
|
| 9.1.2 (Diameter of Stranded conductor) |
1000.0 |
|
|
| 123 |
IS 4020(Parts 1 to 16):1998 RA 2018 - Door shutters-Methods of Tests |
Door shutters-Methods of Tests |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 2-2.1 (Dimension: Height(mm) (IS 4020 (part 2) : 1998)) |
250.0 |
|
| 2-2.2 (Dimension:Width (IS 4020 (part 2) : 1998)) |
250.0 |
|
| 2-2.3 (Diemension:Thickness (IS 4020 (part 2) : 1998)) |
250.0 |
|
| 10 (Slamming Test (IS 4020 (part 10) : 1998)) |
1000.0 |
|
| 8 (Shock resistance Test (IS 4020 (part 8) : 1998)) |
1500.0 |
|
| 7 (Edge Loading Test ( IS 4020 (part 7) : 1998)) |
1500.0 |
|
|
| 124 |
IS 2645:2003 (RA 2017) - Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification |
Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.4 (Chloride content) |
2000.0 |
|
| - (pH) |
1000.0 |
|
|
| 125 |
IRC 137-2022 (2022) - Guideline on use of Fibre-reinforced polymer bars in road projects |
Guideline on use of Fibre-reinforced polymer bars in road projects |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 11.2.5.1 (Mean measured cross sectional area ASTM D7205) |
1000.0 |
|
| 4.1 (Guaranteed Ultimate tensile strength, ASTM D 7205) |
3000.0 |
|
| 0 (Mean Tensile Modulus of Elasticity, ASTM D 7205) |
2000.0 |
|
| 4.1 (Mean Ultimate Tensile Strain, ASTM D 7205) |
3000.0 |
|
| 0 (Guuaranteed Transeverse Shear Strength, ASTM D 7617) |
5000.0 |
|
| 0 (Guuaranteed Bond Strength, ASTM D 7913) |
10000.0 |
|
| 0 (Mean moisture Absorption to Saturation, ASTM D570) |
1000.0 |
|
|
| 126 |
Cable tray - Cable tray |
Cable tray |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Dimension Tests) |
1000.0 |
|
| 2 (Thickness Test) |
1000.0 |
|
| 3 (Perforation area) |
1000.0 |
|
| 4 (Galvanization Thickness Test) |
2000.0 |
|
| 5 (Load Test with applying 1.7 times SWL) |
3000.0 |
|
| 6 (Material Composition Test) |
3000.0 |
|
| 2 (Salt Spray Test, 24 hours) |
960.0 |
|
|
| 127 |
Junction Box - Junction Box |
Junction Box |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Dimensional Tests) |
1000.0 |
|
| 2 (Thickness Test) |
1000.0 |
|
| 3 (Mass of Zinc Coating) |
2000.0 |
|
| 4 (Vertical Load Test) |
3000.0 |
|
|
| 128 |
Race Way - Race Way |
Race Way |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 0 (Dimensional Tests) |
1000.0 |
|
| 1 (Thickness Test) |
1000.0 |
|
| 2 (Mass of Zinc Coating) |
2000.0 |
|
| 3 (Material Composition Test) |
3000.0 |
|
| 4 (Vertical Load Test) |
3000.0 |
|
|
| 129 |
781 (1984) - SPECIFICATION FOR CAST COPPER ALLOY SCREW DOWN BIB TAPS AND STOP VALVES FOR WATER SERVICES |
SPECIFICATION FOR CAST COPPER ALLOY SCREW DOWN BIB TAPS AND STOP VALVES FOR WATER SERVICES |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5 (Dimension, mm) |
2000.0 |
|
| 4 (Chemical Composition) |
5000.0 |
|
| 0 (Measurement of Weight) |
1000.0 |
|
| 0 (Hydrostatic Test of Body) |
5000.0 |
|
|
| 130 |
IS 1060 - METHODS OF SAMPLING AND TEST FOR PAPER AND ALLIED PRODUCTS |
METHODS OF SAMPLING AND TEST FOR PAPER AND ALLIED PRODUCTS |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| IS 1060 (Part.6/Sec.3) (Folding Endurance (MD)) |
1000.0 |
|
| IS 1060 (Part.6/Sec.3) (Folding Endurance (CD)) |
1000.0 |
|
| IS 1060 (Part.5/Sec.8) (Stiffness) |
2000.0 |
|
| IS 1060 (Part5/Sec5) (Substance (Grammage)) |
1000.0 |
|
| IS 1060 (Part 5/Sec 6) (Tensile Index, MD) |
1000.0 |
|
| IS 1060 (Part 5/Sec 6) (Tensile Index, CD) |
1000.0 |
|
| IS 1060 (Part 6/Sec 1) (Tear Index, CD) |
1000.0 |
|
| IS 1060 (Part 6/Sec 1) (Tear Index, MD) |
1000.0 |
|
| IS 1060 (Part 6/Sec 3) (Double Fold, MD) |
750.0 |
|
| IS 1060 (Part 6/Sec 3) (Double Fold, CD) |
750.0 |
|
| IS 1060 (Part 6/Sec 2) (Bursting Strength) |
2000.0 |
|
| IS 1060 (Part 5/Sec 4) (One Minute Cobb) |
2000.0 |
|
| IS 1060 (Part 5/Sec 20) (Smoothness (Bendsten)) |
1000.0 |
|
| IS 1060 (Part 5/Sec 20) (Porosity (Bendsten)) |
1000.0 |
|
| IS/ISO 2471 (Opacity) |
2000.0 |
|
| IS 1060 (Part 4/Sec 13) (Brightness) |
2000.0 |
|
| IS 1060 (Part 5/Sec 12) (Gloss) |
1500.0 |
|
| IS 1060 (Part 5/Sec 2) (Moisture Content) |
1000.0 |
|
| IS 1060 (Part 4/Sec 3) (Ash Content) |
2000.0 |
|
| IS 1060 (Part 3) (Wax Pick) |
2000.0 |
|
| IS 1060 (Part 5/Sec 3) (Thickness) |
1000.0 |
|
| IS 1060 (Part 4/ Sec 7) (pH Value) |
1000.0 |
|
| IS 1060 (Part 3) (Surface pH) |
1000.0 |
|
| Firm's Requirement (Surface Sizing) |
3000.0 |
|
|
| 131 |
Custom Paper Test (2022) - Method of Test for Paper on the lines of IS 1060 |
Method of Test for Paper on the lines of IS 1060 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| IS 1060 (Part.5/Sec.8) (Stiffness) |
2000.0 |
|
|
| 132 |
IEC 60076 - Power Transformers - General |
Power Transformers - General |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Lightning Impulse Voltage Withstand Test (Lightning Impulse Voltage Withstand Test) |
500000.0 |
|
|
| 133 |
NTH/NR/XR/PUF Insulation (2023) - Polyurethane Insulation Block |
Polyurethane Insulation Block |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Firm's Requirement (Density) |
1000.0 |
|
| Firm's Requirement (Dimensions) |
1000.0 |
|
| Firm's Requirement (Flammability Test (Horizontal Direction)) |
5000.0 |
|
| Firm's Requirement (Compression load at 25% deflection) |
2000.0 |
|
|
| 134 |
Custom NR HV - As per Customer Test Request |
As per Customer Test Request |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 0 (Test Results as per Customer Test Request) |
15000.0 |
|
|
| 135 |
IS-516-(Part-11)-2020 - Hardened Concrete-Determination of Portland cement Content of Hardened Hydraulic Cement Concrete |
Hardened Concrete-Determination of Portland cement Content of Hardened Hydraulic Cement Concrete |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Clause no.6 (Ratio of Cement : Concrete) |
6000.0 |
|
|
| 136 |
IS 516 : Part 5 : Sec 1 (2018) - Hardened Concrete -Methods of Test Part 5 Non-destructive Testing of Concrete Section 1 Ultrasonic Pulse Velocity Testing ( First Revision ) |
Hardened Concrete -Methods of Test Part 5 Non-destructive Testing of Concrete Section 1 Ultrasonic Pulse Velocity Testing ( First Revision ) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 137 |
DIN 48 201 (1981) - Bronze (Bz) conductors used for suspended wiring. |
Bronze (Bz) conductors used for suspended wiring. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3 (Dimensions, mm) |
1000.0 |
|
| 3 (Weight, kg/km) |
1000.0 |
|
| 3 (Breaking Strength, kN) |
3000.0 |
|
| 5.1 (Direction of lay) |
1000.0 |
|
| 5.2 (Lay Ratio) |
1000.0 |
|
|
| 138 |
DIN EN 50149 (2013-02) - Electric traction – Copper and copper alloy grooved contact wires |
Electric traction – Copper and copper alloy grooved contact wires |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4 (Chemical Composition) |
5000.0 |
|
| 4.6 (Electrical properties) |
3000.0 |
|
| 4.7 (Tensile strength, MPa) |
2000.0 |
|
| 4.7 (Percentage elongation after fracture, %) |
1000.0 |
|
| 4.7 (Breaking load, kN) |
3000.0 |
|
| 5.3 (Profiles and dimensions) |
2000.0 |
|
|
| 139 |
NTH/NR/CHEM/CUSTOM/FRP 01 - FIRE RETARDANT PAINT & COATED CABLE ANALYSIS |
FIRE RETARDANT PAINT & COATED CABLE ANALYSIS |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Table 1 (Circuit Integrity for 4 Hours ( as per customer specification)) |
2000.0 |
|
| Table 1 (FIRE RETARDANT TEST) |
2000.0 |
|
| IS 101 (PART 5/SEC 2) (FLEXIBILITY & ADHESION - SCRATCH HARDNESS) |
1500.0 |
|
| IS 101 (PART 5/SEC 2) (FLEXIBILITY & ADHESION - BEND TEST) |
1500.0 |
|
| Table 1 (RESISTANCE TO ACID) |
1500.0 |
|
| Table 1 (RESISTANCE TO ALKALI) |
1500.0 |
|
|
| 140 |
NTH/NR/XR/EVA (2023) - Ethylene Vinylene Acetate (EVA) Material Specification |
Ethylene Vinylene Acetate (EVA) Material Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Firm's Requirement (Density) |
1000.0 |
|
| Firm's Requirement (Melt Flow Index) |
2000.0 |
|
|
| 141 |
NCD 1427 Issue 1 - Specification for mineral wool marine board for thermal & acoustic insulation |
Specification for mineral wool marine board for thermal & acoustic insulation |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Appendix B, Table -B1(b)(i) (Compression) |
2000.0 |
|
| Appendix B,Table (b) (ii) (Recovery) |
1000.0 |
|
| Appendix B ,Table-B1(e) (Water Absorption) |
2000.0 |
|
| Appendix B ,Table-B1(d) (Inter laminar Adhesion) |
2000.0 |
|
| Appendix A, Clause-3 (Ability to Bend) |
1000.0 |
|
| Appendix B, Table -B1(a) (Percent Alkalinity (As Na2O)) |
1000.0 |
|
| Appendix B ,Table-B1(f) (Shot Content) |
2000.0 |
|
| Appendix B ,Table-B1(C) (Puncture Resistance) |
2000.0 |
|
| Appendix A , Clause No 2.1 (Weight of Glass Cloth Facing) |
1000.0 |
|
| Appendix A , Clause No 2.2 (Thickness of Glass Cloth Facing) |
1000.0 |
|
| Appendix A , Clause No 2.3.1 (Warp ends/10cm) |
1000.0 |
|
| Appendix A , Clause No 2.3.2 (Weft ends/10cm) |
1000.0 |
|
| Appendix A , Clause 2.5.1 (Breaking Strength (Warp)) |
2000.0 |
|
| Appendix A, Clause- 2.5.2 (Breaking Strength (Weft)) |
2000.0 |
|
| Appendix-C, 3(h) (Bond Strength) |
1500.0 |
|
| Appendix-C, 3(g) (Initial Tack Test) |
1500.0 |
|
|
| 142 |
9295 (1983) - SPECIFICATION FOR STEEL TUBES FOR IDLERS FOR BELT CONVEYORS |
SPECIFICATION FOR STEEL TUBES FOR IDLERS FOR BELT CONVEYORS |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7.1 (Chemical composition, % by mass (Sulphur)) |
750.0 |
|
| 7.1 (Chemical composition, % by mass (Phosphorus)) |
750.0 |
|
| 8.1 (Tensile strength, N/mm2) |
1000.0 |
|
| 8.1 (Yield stress, N/mm2) |
1000.0 |
|
| 8.1 (Percent Elongation) |
1000.0 |
|
| 8.3 (Flattening Test) |
1000.0 |
|
| 9.1 (Dimension (Outside diameter), mm.) |
1000.0 |
|
| 9.1 (Dimension (Thickness), mm.) |
1000.0 |
|
| 9.1 (Mass, kg/m) |
1000.0 |
|
|
| 143 |
IS 3601 (2006) - Steel tubes for mechanical and general engineering purposes - Specification (Second Revision) |
Steel tubes for mechanical and general engineering purposes - Specification (Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.1 (Sulphur) |
1250.0 |
|
| 4.1 (Phosphorus) |
1250.0 |
|
| 13.1 (Tensile strength, MPa) |
1000.0 |
|
| 13.1 (Yield stress, MPa) |
1000.0 |
|
| 13.1 (% Elongation) |
1000.0 |
|
| 13.2 (Flattening test) |
1000.0 |
|
| 10 (Outside diameter, mm) |
1000.0 |
|
| 10 (Thickness, mm) |
1000.0 |
|
| 10 (Weight, kg/m) |
- |
|
|
| 144 |
IEC 61537 (2006) - Cable Management-Cable tray system of Pre-galvanised steel sheet/ Stainless Steel |
Cable Management-Cable tray system of Pre-galvanised steel sheet/ Stainless Steel |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Table 1 (Chemical composition, % by mass) |
5000.0 |
|
| 3 (Dimensions, mm) |
1000.0 |
|
| 3 (Thickness, mm) |
1000.0 |
|
| 3 (Bend test) |
1000.0 |
|
| 3 (0.2% Proof Stress, N/mm2) |
1000.0 |
|
| 3 (Tensile strength, N/mm2) |
1000.0 |
|
| 3 (Percent Elongation) |
1000.0 |
|
| 4 (Mass of Zinc Coating, GSM) |
2000.0 |
|
| 7.2 (Uniformity of Zinc coating) |
1000.0 |
|
| 7.3 (Adhesion Test) |
1000.0 |
|
| 5 (Safe Working Load test) |
3000.0 |
|
|
| 145 |
IS 739 (1992 (RA 2022)) - WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS - WIRE FOR GENERAL ENGINEERING* PURPOSES - SPECIFICATION |
WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS - WIRE FOR GENERAL ENGINEERING* PURPOSES - SPECIFICATION |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8.1 (Chemical composition, % by mass, (As per IS 2590)) |
5000.0 |
|
| 9.2 (Tensile strength, N/mm2) |
3000.0 |
|
| 9.3 (Wrapping test) |
1000.0 |
|
|
| 146 |
IS 2590 - SPECIFICATION FOR PRIMARY ALUMINIUM INGOTS FOR REMELTING FOR GENERAL ENGINEERING PURPOSES |
SPECIFICATION FOR PRIMARY ALUMINIUM INGOTS FOR REMELTING FOR GENERAL ENGINEERING PURPOSES |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 147 |
BS 1474 (1987) - Specification for Wrought aluminium, and aluminium alloys for general engineering purposes: bars, extruded round tubes and sections |
Specification for Wrought aluminium, and aluminium alloys for general engineering purposes: bars, extruded round tubes and sections |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6 (Tensile strength, N/mm2) |
1000.0 |
|
| 4 (Chemical composition, % by mass) |
5000.0 |
|
| 6 (Percent Elongation) |
1000.0 |
|
| 7 (Dimensions, mm) |
1000.0 |
|
| 0 (Anodic Coating) |
2000.0 |
|
| 6 (0.2% Proof Stress, N/mm2) |
1000.0 |
|
|
| 148 |
NTH/NR/CHEM/CUSTOM/PU PRIMER & TOP COAT - SURFACE PU PRIMER & TOP COAT |
SURFACE PU PRIMER & TOP COAT |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Table 1 (PU Based Floor Coating PRIMER (Please see Annexure)) |
8000.0 |
|
| Table 1 (PU PRIMER TOP COAT ( Please see Annexure)) |
8000.0 |
|
|
| 149 |
NTH/NR/CHEM/CUSTOM/CONDENSER CHILLEDWATER - CONDENSER AND CHILLED WATER AS PER CUSTOMER REQUIREMENT |
CONDENSER AND CHILLED WATER AS PER CUSTOMER REQUIREMENT |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Table 1 (chilled water (Please see Annexure0) |
7000.0 |
|
| Table 1 (CONDENSER WATER ( Please see Annexure)) |
7000.0 |
|
|
| 150 |
ASTM A240 (2020) - Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5 (Tensile Strength) |
1000.0 |
|
| 5 (Yield Strength) |
1000.0 |
|
| 5 (Elongation in 50mm) |
1000.0 |
|
| 5 (Hardness) |
2000.0 |
|
| 4 (Chemical composition, % by mass) |
5000.0 |
|
| 0 (Dimension, mm) |
2000.0 |
|
| 0 (Load Test, kN) |
1000.0 |
|
|
