NTH - Management Information System

National Test House (NR), Ghaziabad

Kamla Nehru Nagar, Ghaziabad, Uttar Pradesh - 201002, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

7003775955 director-gzb[at]nth[dot]gov[dot]in

Scope List

Reset

591 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

511

IS 1500 : Part 1 (2019) - Metallic materials - Brinell hardness test: Part 1 test method (Fifth Revision)

Metallic materials - Brinell hardness test: Part 1 test method (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Hardness)	2000.0

512

IS 513 : Part 2 (2016) - Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Yield stress)	1000.0
7.2 (Bend Test)	1000.0
10 (Thickness)	1000.0

513

IS 2062 Part 1 (2025) - Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10 (Tensile Strength - IS 1608 (Part 1): 2022)	1000.0
10 (Yield Stress - - IS 1608 (Part 1): 2022.)	1000.0
10 (% Elongation - IS 1608 (Part 1): 2022.)	1000.0
11 (Bend Test - IS 1599: 2019.)	1500.0
12 (Impact Test (For Specified Quality Grade))	5000.0
8.2 (Carbon)	500.0
8.2 (Sulphur)	500.0
8.2 (Phosphorus)	500.0
8.2 (Manganese)	500.0
8.2 (Silicon)	500.0
8.2 (Carbon Equivalent, %)	500.0
0 (Percent elongation test, %)	3000.0
0 (Yield strength Test, N/mm2)	3000.0
0 (Tensile strength & Yield Strength Test, N/mm2)	5000.0
0 (Thickness)	500.0
0 (Coating Thickness)	2000.0
0 (Mass of Zinc Coating)	2000.0
0 (Uniformity of Coating)	1000.0
0 (Salt Spray Test)	60000.0
0 (Overall Weight)	1500.0
0 (Dimensions)	1000.0
12 (Impact Test)	5000.0
7 (Freedom from Defects)	1000.0
0 (Adhesion Test)	1000.0

514

IS 1786 (2008) - High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.7 (5) (Percentage increase in Bond Stress of Deformed Bar against corresponding Plain Bar at 0.25 mm slip (For size up to 12 mm), % - IS 2770(Part 1))	1250.0
4.2 (17) (Chemical Composition without micro alloying elements, % by mass.)	2000.0
9.4 (1) (Rebend test (32 to 40mm)- IS 1786: 2008)	1500.0
9.3 (Bend test - IS 1599: 2023.)	1000.0
7.2 (Mass per metre run, kg/m - IS 1786: 2008)	1000.0
9.2 (1) (TS/ YS Ratio - (IS 1786: 2008/ IS 1608 (Part 1): 2022).)	-
9.2 (2) (Elongation Percent on gauge length of 5.65 Square Root of Crosss- Sectional Area, % - IS 1608 (Part 1): 2022.)	1000.0
9.2 (6) (Tensile Strength (32 to 40 mm), N/mm² - IS 1608 (Part 1): 2022.)	1500.0
4.2 (2) (Carbon, % by mass (As per ASTM E 415/ IS 8811/IS 228).)	500.0
4.2 (3) (Sulphur, % by mass (As per ASTM E 415/ IS 8811/IS 228))	500.0
4.2 (4) (Phosphorus, % by mass (As per ASTM E 415/ IS 8811/IS 228))	500.0
4.2 (5) (Sulphur+ Phosphorus, % by mass.)	500.0
9.2 (4) (Tensile Strength (up to 12 mm), N/mm² - IS 1608 (Part 1): 2022.)	-
9.2 (5) (Tensile Strength (16 to 28 mm), N/mm² - IS 1608 (Part 1): 2022.)	1000.0
9.2 (6) (Tensile Strength (32 to 40 mm), N/mm² - IS 1608 (Part 1): 2022.)	1500.0
9.4 (Rebend test (0 - 28 mm) - IS 1786: 2008)	1000.0
9.3 (Bend test - IS 1599: 2023.)	1000.0
9.2 (2) (Elongation Percent on gauge length of 5.65 Square Root of Crosss- Sectional Area, % - IS 1608 (Part 1): 2022.)	1000.0
9.2 (Yield Stress/ 0.2 % Proof Stress. N/mm² -- IS 1608 (Part 1): 2022.)	1000.0
9.2 (3) (Total Elongation at Maximum Force on gauge length of 5.65 Square Root of Crosss- Sectional Area, % - IS 1608 (Part 1): 2022.)	-
9.1.1 (Tensile Strength)	3000.0
9.1.2 (Yield/0.2% Proof Stress)	3000.0
9.1.3 (Percentage Elongation)	3000.0
4.2 (1) (Carbon Equivalent (CE), , % by mass.(As per ASTM E 415/ IS 8811/IS 228/IS 3025))	2000.0
0 (Salt spray test 48hrs as per ASTM B117)	2000.0
0 (Test for thickness of coating)	3000.0
5.7 (Pull out test upto 32mm)	15000.0

515

IS 513 : Part 1 (2016) - Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Thickness)	1000.0
8.1 (Yield stress)	1000.0
8.3 (Hardness Test)	2000.0
8.1 (Tensile strength)	1000.0
8.1 (% Elongation)	1000.0
8.4 (Bend Test)	1000.0

516

IS 277 (2018) - Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Tensile strength, MPa)	1000.0
8.1 (Yield Strength, MPa)	1000.0
8.1 (Percentage Elongation, %)	1000.0
8.2 (Bend Test)	1000.0
14 (Total coated thickness, mm)	1000.0
8.1 (Mass of Zn coating)	2000.0
5.1 (Phosphorus)	500.0
5.1 (Sulphur)	500.0
5.1 (Manganese)	500.0
5.1 (Carbon)	500.0
0 (Thickness of Paint coating at side 1)	1000.0
0 (Thickness of Paint coating at side 2)	1000.0
0 (Base metal thickness, mm)	1000.0
15 (Dimensions of Corrugated sheet)	1000.0
12 (Freedom from defects)	1000.0
0 (Pencil Hardness Test as per IS 14246)	1000.0

517

IBR 1950 (2023) - Qualified Boiler Welder's Certificate

Qualified Boiler Welder's Certificate

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IBR-1950, Chapter -XIII (Welder Test - Plate)	3000.0
NTH Additional Charges for Testing (Scientist Charges)	5000.0
IBR-1950, Chapter -XIII (IBR Welder Test - Tube/Pipe (MMAW)- Horizontally Fixed)	3500.0
IBR-1950, Chapter -XIII (IBR Welder Test - Tube/Pipe (MMAW)- Vertically Fixed)	3500.0
IBR-1950, Chapter -XIII (IBR Welder Test - Tube/Pipe (GTAW+ MMAW)- Horizontally Fixed)	4500.0
IBR-1950, Chapter -XIII (IBR Welder Test - Tube/Pipe (GTAW+ MMAW)- Vertically Fixed)	4500.0
0 (Scientist charge 2)	5000.0

518

ASME ASME (2021) - Performance test ( Plate & electrodes not supplied by NTH)

Performance test ( Plate & electrodes not supplied by NTH)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASME (Welding procedure qualification)	7000.0
QB 484 (Brazing Performance Test)	5000.0

519

ASME ASME Section IX (2021) - Preparation of welding procedure specification (WPS) as per ASME Section IX

Preparation of welding procedure specification (WPS) as per ASME Section IX

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASME Section IX (Welding procedure Specification)	10000.0

520

ASME Section IX (2019) - 2019 Boiler and Pressure Vessel Code

2019 Boiler and Pressure Vessel Code

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
QW 191 (Radiography Test -Pipe)	3200.0
QW 191 (Radiography Test -Plate)	1200.0

521

IS 6012 (1992) - Measurement of coating thickness by eddy current method (First Revision)

Measurement of coating thickness by eddy current method (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 6012 (Coating thickness)	2000.0

522

IS 2595 (2008) - Industrial radiographic testing - Code of practice (Second Revision)

Industrial radiographic testing - Code of practice (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 2595 (Radiography)	2000.0

523

IS 5523 (1983) - Methods of testing anodic coatings on aluminium and its alloys (First Revision)

Methods of testing anodic coatings on aluminium and its alloys (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 5523 (Coating thickness)	2000.0

524

13683 (2006) - Ring Spun Grey Cotton Yarn

Ring Spun Grey Cotton Yarn

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

525

IS 10733 (1983) - Tanker Hose of Rubber

Tanker Hose of Rubber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

526

IS 8329 (2000) - Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1.1 (External diameter)	1000.0
10.1.1 (Tensile Strength)	2000.0
10.1.1 (Percent Elongation)	1500.0
10.2 (Brinell Hardness)	2000.0
16.2 (C-2.3) (Bituminous Coating Test)	1000.0
15.3 (Ovality of pipe)	1000.0
16.3 (Thickness of Cement mortar lining of pipe)	1000.0
13.3 (Wall Thickness of pipe)	1000.0
13.2 (Bore Clearance of mortar lining in ductile iron pipe)	1000.0

527

CBIP 317 (2013) - Central Board of Irrigation & Power-Manual No-317- Single Phase Transformer

Central Board of Irrigation & Power-Manual No-317- Single Phase Transformer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Sec BB (3) (Magnetic Balance Test)	2000.0
Sec BB (3) (Measurement of unbalanced current)	2000.0
Sec BB (3) (Polarization lndex)	5000.0
Sec BB (3) (Voltage)	3000.0
Sec BB (3) (Unbalanced Current)	3000.0
17.3.2 (Permanent Deflection)	10000.0
17.3.1 (Permanent Deflection)	8000.0

528

IS 335 (1993) - NEW INSULATING OILS- SPECIFICATION

NEW INSULATING OILS- SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.5.2.6 (Measurernent of Break Down Voltage of trransformer Oil)	10000.0

529

IS 15652 (2006) - Insulating mats for electrical purposes - Specification

Insulating mats for electrical purposes - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.2.1 (Insulation Resistance with Water)	4000.0
8.2.2 (Leakage Current Test)	2500.0
8.2.3 (AC Dielectric Strength)	7000.0
8.2.4 (AC Proof Voltage)	3000.0
6.3 (Thickness)	500.0
8.4.2 (Low Temperature Resistance & High Voltage test)	4000.0
8.6 (Extreme low temperature test)	6000.0
8.1 (Tensile Strength and Elongation at Break)	1500.0
8.3 (Tensile Strength and Elongation at break After Ageing)	4000.0
8.5 (After Acid/Alkalis and Oil Resistance)	4500.0
8.4.1 (Flame Retardance)	2000.0
6.2 (Dimensions)	1000.0

530

IS 15769 (2008) - Flux Cored (Tubular) Electrodes for Gas Shielded and Self Shielded Metal welding of Carbon or Carbon Manganese Steel

Flux Cored (Tubular) Electrodes for Gas Shielded and Self Shielded Metal welding of Carbon or Carbon Manganese Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Diameter of Core Wire)	500.0
4.2 (Temper)	1000.0
4.2 (Cast)	500.0
4.2 (Helix)	500.0
4.3 (Uniformity)	500.0
4.4.3 (Spools, Overall Diameter A)	500.0
4.4.3 (Spools, Overall Width, B)	500.0
4.4.3 (Spools, Inner Diameter, C)	500.0
4.4.3 (Spools, Distance Between Axes D)	500.0
4.4.3 (Spools, Driving Hole Diameter E)	500.0
4.4.3 (Spools, Weight, Max)	500.0
5.8 (Chemical Analysis)	5000.0
5.2 (Radiographic Examination)	1500.0
5.3 (Tensile Test)	3000.0
5.4 (Charpy Impact Test)	3000.0
5.1.3.2 (Fillet Weld Fracture)	4000.0
5.1.3.2 (Dimension of Fillet Weld)	500.0
5.5 (Transverse Tensile Test)	3000.0
5.6 (Longitudinal Guided Bend Test)	1000.0
5.7 (Diffusible Hydrogen Test)	5000.0

531

IS 2026 : Part 1 (2011) - Power Transformers: Part 1 General (Second Revision)

Power Transformers: Part 1 General (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1.2(a) (Temperatur Rise)	20000.0
10.1.1(a) (Measurement of windlng Resistance)	1600.0
10.1.1(b) (Voltage ratio & Phase Displacement)	3200.0
10.1.1 (C) (% impedance and load loss)	12800.0
10.1.1(d) (No Load loss and current)	9600.0
10.1.1(e) (Separate source AC voltage withstand test)	4000.0
10.1.1(e) (Induced Overvoltage)	6400.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	500000.0
10.1.3(d) (Measurement of Zero phase sequence impedance for 3 Phase transformer)	3000.0
10.1.3(g) (% Harmonics)	10000.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
10.1.3 (f) (Noise Level)	10000.0
7 (Rating Plate Details)	-
17.3.1 (a) of CBIP Pub. No. 317 (Pressure Test Routine (Deflection))	8000.0
17.3.2 (a) of CBIP Pub. No. 317 (Vacuum Test - Type (Deflection))	10000.0
17.3.2 (b) of CBIP Pub. No. 317 (Oil Leakage Test (Pressure Test - Type))	10000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	3000.0
As per IS : 335 (Breakdown Voltage Test)	10000.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0
10.1.2 (b) (Lightning Impulse Voltage Withstand Test upto 11 KV & 500 KVA Rating)	40000.0
10.1.2 (b) (Lightning Impulse Voltage Withstand Test upto 11 KV & 1000 KVA Rating)	50000.0
10.1.2 (b) (Lightning Impulse Voltage Withstand Test upto 11 KV & 2500 KVA Rating)	65000.0
10.1.2 (b) (Lightning Impulse Voltage Withstand Test For Power Transformers of 33 KV Class upto 20 MVA)	250000.0
10.1.3 (Measurement of Dissipation Factor (Tan Delta) & Capacitance)	30000.0

532

IS 2713 : PART 1 TO 3 (1980) - Tubular Steel Poles for Overhead Power Lines

Tubular Steel Poles for Overhead Power Lines

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.4 (Weight of Pole)	1000.0
15.1 (Dimension of Base Plate)	1000.0
8.1 (Outside Diameter (Top, Middle , Bottom Section of Pole))	3000.0
8.3 (Length (Overall Length, Top, Middle , Bottom Section of Pole))	4000.0
8.2 (Thickness (Top, Middle , Bottom Section of Pole))	3000.0
8.5 (Straightness)	1000.0
7 (Freedom from defect)	1000.0
10.1.3 (Deflection Test)	1000.0
10.1.4 (Permanent Set Test)	1500.0
10.1.5 (Drop Test)	1000.0
6 (Chemical Composition (Top, Middle , Bottom Section of Pole))	4500.0
11.2 of IS 1161: 2014 (Tensile Test (Top, Middle , Bottom Section))	9000.0
11.3.2 of IS 1161: 2014 (Flattening test (Top, Middle , Bottom Section of Pole))	3000.0
13.2 (Protection against corrosion (Galvanized Test))	2000.0

533

2026 (Part-11) (2021) - Specification for dry - Type power transformers

Specification for dry - Type power transformers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13.1.(a) (Measurement of Winding Resistance)	1000.0
13.1.(b) (Measurement of Voltage ratio & voltage vector relationship test)	2000.0
13.1.(c) (Measurement of lmpedance Voltage ,Short Circuit lmpedance and Load Loss)	8000.0
13.1.(d) (Measurement of No Load Loss & Current)	6000.0
13.1.(e) (Separate source Voltage withstand test)	2500.0
13.1.(f) (lnduced Over voltage withstand test)	4000.0
13.1(g) (Lightning Impulse Test)	65000.0
13.1.(h) (Temperature Rise Test)	40000.0
13.3.(b) (Measurement of acoustic sound Level)	7000.0

534

IS 4454 : Part 1 (2001) - Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 (Tensile Strength)	3000.0
9 (Dimensions)	1000.0

535

IS 15622 (2017) - Pressed Ceramic Tiles - Specification (First Revision)

Pressed Ceramic Tiles - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6, Tables 5 to 9, Sl No (iii), (a) (Resistance to staining IS 13630(8)/(7):2019)	1000.0
6, Tables 5 to 9, Sl No (iii), (b) (Resistance to household chemicals swimming pools, and water cleansers except to cleansing agents containing hydrofluoric acid and its compounds IS 13630(8)/(7):2019)	1000.0
6, Tables 5 to 9, Sl No (iii), (c) (Resistance to acid and alkalies (with exception of hydrofloric acid and its compounds-IS 13630(8)/(7):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (f) (Surface Quality-IS13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (a) (Dimensions-Length-IS13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (a) (Dimensions-Width -IS:13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (b) (Dimension-Thickness-Deviation in percent from work size -IS: 13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (d) (Rectangularity-Maximum deviation in percent to corresponding work size-IS: 13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (c) (Straightness of sides(Facial sides)Maximum deviation in percent to corresponding work size- IS13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (e-1,2,3) (Surface Flatness-Maximum deviation in percent from flatness-(Centre curvature, Edge curvature & warpage) -IS: 13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (ii), (a) (Water Absorption-IS13630 (Part 2):2019)	1000.0
6, Tables 5 to 9, Sl No (ii), (b) (Modulus of rupture in N/mm²- IS13630 (Part6):2019)	2000.0
6, Tables 5 to 9, Sl No (ii), (c) (Breaking of strength in N- IS13630 (Part 6):2019)	2000.0
6, Tables 5 to 9, Sl No (ii), (e) (Scratch Hardness of surface (Mohs' Scale)-IS13630 (Part 13):2019)	2000.0
6, Tables 5 to 9, Sl No (ii), (j) (Crazing Resistance- IS13630 (Part 9):2019)	1500.0
6, Tables 5 to 9, Sl No (ii), (k) (Impact resistance-Coefficient of Restitution-IS13630 (Part 14):2019)	1000.0
6, Tables 8 and 9, Sl No (ii), (q) (Bulk Density-IS13630 (Part 2):2019)	1000.0
6, Table 9, Sl No (iii), (a, b, c)-1(Part 8) (Chemical properties-glazed- IS13630 (Part 8):2019)	5000.0

536

IS 1237 (2012) - Cement Concrete Flooring Tiles - Specification

Cement Concrete Flooring Tiles - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.6 (Wet transverse strength-Annex F of IS 1237:2012)	2000.0
12.5 (Water Absorption-Annex E of IS 1237:2012)	1000.0
12.4 (Straightness-Annex D of IS 1237:2012)	500.0
12.3 (Perpendicularity-Annex C of IS 1237:2012)	500.0
10 (General Quality-IS 1237:2012)	100.0
8.3 & Table2 (The thickness of Wearing Layer-IS 1237:2012)	100.0
7, 8.2 & Table1 (Thickness & Tolerances-IS 1237:2012)	100.0
7 & 8.1, Table1 (Dimensions & Tolerances-IS 1237:2012)	200.0
12.7 (Resistance to wear-Annex G of IS 1237:2012)	2500.0

537

IS 10262 (2019) - Concrete Mix Proportioning — Guidelines ( Second Revision )

Concrete Mix Proportioning — Guidelines ( Second Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Concrete Mix design (IS 10262:2019) with Admixture)	35000.0
1 (Concrete Mix Proportioning — Guidelines (without admixture))	30000.0

538

IS 1489 : Part 2 (2015) - Portland - Pozzolana cement - Specification: Part 2 calcined clay based

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7, Table 2, Sl No 6 (Drying Shrinkage IS 4031(10):1988)	1000.0
7, Table 2, Sl No 4c (28 Days Compressive strength, MPa- IS 4031(6):1988)	1000.0
7, Table 2, Sl No 4b (7 Days Compressive strength,168±2 h, MPa- IS 4031(6):1988)	1000.0
7, Table 2, Sl No 4a (3 Days Compressive strength,72±1 , MPa- IS 4031(6):1988)	1000.0
7, Table 2, Sl No 3b (Setting time-Final, IS 4031(5):1988)	250.0
7, Table 2, Sl No 3a (Setting time- Initial IS 4031(5):1988)	250.0
7, Table 2, Sl No 2b (Soundness-autoclave method IS 4032(3):1988)	1000.0
7, Table 2, Sl No 2a (Soundness-Lechatlier method IS 4032(3):1988)	500.0
6, Table 1, Sl No 6 (Alkali content IS 4032:1985)	2000.0
6, Table 1, Sl No 5 (Chloride content IS 4032:1985)	800.0
6, Table 1, Sl No 4 (Loss on Ignition IS 4032:1985)	800.0
6, Table 1, Sl No 3 (Total Sulphur content IS 4032:1985)	800.0
6, Table 1, Sl No 2 (Magnesia IS 4032:1985)	800.0
6, Table 1, Sl No 1 (Insoluble residue IS 4032:1985)	800.0

539

IS 16227 : Part 1 (2016) - Instrument transformers: Part 1 general requirements

Instrument transformers: Part 1 general requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2.3.2 (Multi chopped (100) Lightning Impulse Voltage Test (CT / PT ) 220 KV Class)	150000.0
7.2.3.2 (Multi chopped (100) Lightning Impulse Voltage Test (CT / PT ) 132 KV Class)	100000.0

540

IS 1489 (Part 1) (2015) - Portland pozzolana cement - Specification: Part 1 Fly Ash Based

Portland pozzolana cement - Specification: Part 1 Fly Ash Based

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7, Table 2, Sl No 1 (Fineness IS 4031(2):1999)	1000.0
7, Table 2, Sl No 6 (Drying Shrinkage IS 4031(10):1988)	1000.0
7, Table 2, Sl No 4c (28 Days Compressive strength, IS 4031(6):1988)	1000.0
7, Table 2, Sl No 4b (7 Days Compressive strength, IS 4031(6):1988)	1000.0
7, Table 2, Sl No 4a (3 Days Compressive strength, IS 4031(6):1988)	1000.0
7, Table 2, Sl No 3b (Setting time-Final IS 4031(5):1988)	250.0
7, Table 2, Sl No 3a (Setting time-Initial IS 4031(5):1988)	250.0
7, Table 2, Sl No 2b (Soundness-autoclave method IS 4031(3):1988)	1000.0
7, Table 2, Sl No 2a (Soundness-Lechatlier method IS 4031(3):1988)	500.0
6, Table 1, Sl No 6 (Alkali content IS 4032:1985)	2000.0
6, Table 1, Sl No 5 (Chloride content, IS 4032:1985)	800.0
6, Table 1, Sl No 4 (Loss on ignition IS 4032:1985)	800.0
6, Table 1, Sl No 3 (Total Sulphur content IS 4032:1985)	800.0
6, Table 1, Sl No 2 (Magnesia IS 4032:1985)	600.0
6, Table 1, Sl No 1 (Insoluble residue, IS 4032:1985)	600.0
13 (Consistency of Cement)	500.0