NTH - Management Information System

National Test House (NR), Ghaziabad

Kamla Nehru Nagar, Ghaziabad, Uttar Pradesh - 201002, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

7003775955 director-gzb[at]nth[dot]gov[dot]in

Scope List

Reset

616 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

481

IS 1367 : Part 3 (2017) - Technical Supply Conditions for Threaded Steel Fasteners Part 3 Mechanical Properties of Fasteners Made of Carbon Steel and Bolts, Screws and Studs

Technical Supply Conditions for Threaded Steel Fasteners Part 3 Mechanical Properties of Fasteners Made of Carbon Steel and Bolts, Screws and Studs

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Chemical Composition, % by mass)	2500.0
6 (Vanadium, % by mass)	500.0
6 (Molybdenum, % by mass)	500.0
6 (Nickel, % by mass)	500.0
6 (Chromium, % by mass)	500.0
6 (Lead, % by mass)	500.0
9.1.4 (Wedge Load test as per IS 1367 Part 3)	3000.0
1.2 (Uniformity of Zn coating)	1000.0
1.1 (Mass of Zinc Coating)	2000.0
9.7.1b (Percentage Elongation after fracture on Machined test piece, %.)	1000.0
9.7.1a (Yield Strength on Machined test piece, MPa.)	1000.0
9.7.1 (Tensile Strength on Machined test piece, MPa.)	1000.0
7 (Mechanical and physical properties (Hardness,Vickers))	2000.0
7 (Mechanical and physical properties (Proof load test))	2000.0
6 (Chemical Composition, % by mass)	2500.0
0 (Shear Strength Test)	3000.0
6 (Silicon)	500.0
6 (Manganese)	500.0
2 (Dimensions)	1000.0

482

ASTM B117 - Salt spray for 3000 hrs ASTM B117

Salt spray for 3000 hrs ASTM B117

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASTM B 117 (Salt Fog Test 5% Nacl solution(for 96 hrs) ASTM 117B/IEC 60512-11-6 AS PER CLAUSE NO. 7.4.9 FOR INTER VEHICULAR COUPLER UNIT 500AMP AS PER RDSO SPEC. NO. RDSO/PE/SPEC/AC/0177-(REV-01)-2013)	5000.0
ASTM D 3359 (Cross Cut Test on Painted or Coated Specimen)	2000.0
ASTM B 117 (Salt Fog Test 5% Nacl solution(for 96 hrs) ASTM 117B/IEC 60512-11-6 AS PER CLAUSE NO. 7.4.9 FOR INTER VEHICULAR COUPLER UNIT 500AMP AS PER RDSO SPEC. NO. RDSO/PE/SPEC/AC/0177-(REV-01)-2013)	5000.0
ASTM D 3359 (Cross Cut Test on Painted or Coated Specimen)	2000.0

483

ASTM D6637 (2015) - Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method

Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Method-A (Tensile Strength)	1500.0
Method-A (Elongation at break)	1500.0
Firm's Requirement (Secant Modulus)	2000.0

484

AASHTO T 166 (2021) - AASHTO T 166-Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated Surface-Dry Specimens

AASHTO T 166-Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated Surface-Dry Specimens

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
AASHTO T 166 (Bulk specific gravity)	2000.0

485

MORTH : Part 5 (2013) - SPECIFICATIONS FOR ROAD AND BRIDGE WORKS/ASTM

SPECIFICATIONS FOR ROAD AND BRIDGE WORKS/ASTM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.4,5.2&4.2.1 (Combined BITUMEN CONTENT of each specimens)	6000.0
505 (Density / Bulk Specific Gravity of DBM (AASHTO T 166))	2000.0
507 (Density / Bulk Specific Gravity of BC ( AASHTO T 166 (21)),)	2000.0
505 (Binder Content of DBM, in %)	3000.0
507 (Bitumen Content of BC, in %)	3000.0
CLAUSE-1,Table-1 (Cutting & Preparation of Core sample-Single Stage)	1000.0
505 (Density of DBM Layer-I (Grade-I))	2000.0
505 (Density of DBM Layers-II (Grade-II))	2000.0
Misc (Density of SMA Bituminous Core.)	2000.0
Clause 1 Table 1 (Cutting & Preparation of Core sample -Double Stage)	1000.0
505 (Binder Content of DBM Layers -I, %)	3000.0
505 (Binder Content of DBM Layers-II, %)	3000.0
Misc (Binder Content of SMA Bituminous Core, %)	3000.0
Thickness of core (Thickness of core)	1000.0
Density DAC (Density of Dense Asphaltic Concrete.)	2000.0
Density of SDAC (Density of Semi Dense Asphaltic Concrete)	2000.0
Binder Content DAC (Binder content of Dense Asphaltic Concrete)	3000.0
Binder Content of SDAC (Binder content of Semi Dense Asphaltic Concrete)	3000.0

486

IS 1367 : Part 6 (2018) - Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Proof Load)	3000.0
7 (Hardness Test)	2000.0
6 (Carbon, % by mass)	500.0
6 (Phosphorus, % by mass)	500.0
6 (Sulphur, % by mass)	500.0
6 (Manganese, % by mass)	500.0
7 (Surface Integrity)	1200.0
0 (Mass of Zinc Coating)	2000.0
0 (Uniformity of coating)	1000.0
1.1 (Dimensions)	1500.0

487

IS 1367 : Part 3 (2017) - Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Tensile load, N.)	3000.0
7 (Proof Load, N.)	3000.0
7 (Hardness Test)	2000.0
5 (Surface Integrity)	1200.0
6 (Carbon, % by mass)	500.0
6 (Phosphorus, % by mass)	500.0
6 (Sulphur, % by mass)	500.0
6 (Boron, % by mass)	625.0
9.14 (Impact Strength at (-) 20⁰C)	5000.0
1 (% Reduction in Area)	1000.0
2 (Uniformity test)	1000.0
3 (Mass of Zinc Coating)	2000.0
4 (Dimensions of the Bolts)	2000.0
9.7.1 (Tensile Strength on Machined Test Piece, MPa.)	1000.0
9.7.1a (Yield Strength on Machined Test Piece, MPa.)	1000.0

488

IS 14223 : Part 1 (1995) - Polished Building Stones: Part 1 Granite

Polished Building Stones: Part 1 Granite

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Specific gravity)	1000.0
5 (Water absorption)	1000.0
5 (Hardness)	2000.0
5 (Moisture content)	500.0
5 (Dry density )	1000.0

489

IS 3622 (1977) - Sandstone (slabs And Tiles)

Sandstone (slabs And Tiles)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Water Absorption)	1000.0
4.1 (Transverse Strength)	2000.0

490

IS 1536 (2001) - Centrifugally cast (Spun) iron pressure pipes for water, gas and sewage - Specification (Fourth Revision)

Centrifugally cast (Spun) iron pressure pipes for water, gas and sewage - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13 (Dimensions)	1000.0
11.3 (Brinell hardness)	1500.0
13.5 (Mass)	1000.0
15 (Coating)	1000.0
0 (Thickness)	500.0
0 (Tensile Test)	3000.0
0 (Ring Test)	3000.0
0 (Ovality)	1000.0
0 (Class of Pipe)	-
0 (Marking)	-
0 (Straightness)	-
0 (Visual Check & Hammer test)	1000.0

491

NTH/NR/RPPT/Rubber & Rubber Products (2025) - Rubber Sheets and Rubber Products

Rubber Sheets and Rubber Products

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 3400 (Part 1) (Tensile Strength)	2000.0
IS 3400 (Part 1) (Elongation at Break)	1000.0
IS 3400 (Part 1) (Tensile strength after heat aging)	3000.0
IS 3400 (Part 1) (Elongation at break after heat ageing)	2000.0
- (Shore 'A' Hardness)	1000.0
IS 3400 (Part /10/Sec.1) (Compression Set)	2000.0
IS 3400 (Part 17) (Tear Strength)	2000.0
- (Shore 'A' Hardness)	1000.0
IS 3400 (Part 2) (Hardness, IRHD)	1000.0
IS 3400 (Part 3) (Abrasion Resistance)	2000.0
IS 3400 (Part 4) (Accelerated Ageing and Heat Resistance)	3000.0
IS 3400 (Part 5) (Adhesion of rubbers to textile fabrics)	3000.0
IS 3400 (Part 6) (Determination of the Effect of Liquids)	5000.0
IS 3400 (Part 16) (Flexing Resistance)	3000.0
IS 3400 (Part 15) (Volume Resistivity)	2000.0
Firm's Requirement (Thickness)	1000.0
Firm's request (Dimensions)	1000.0
Firm's request (Hardness-IRHD)	1000.0
As per DIN 53516 (Abrasion Resistance)	5000.0

492

IS 12235 : Part 1 to 19 (2004) - Thermoplastics Pipes and Fittings - Methods of Test

Thermoplastics Pipes and Fittings - Methods of Test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Part 5 (Longitudinal Reversion)	2000.0
Part 8 (Resistance to Internal Hydrostatic Pressure)	5000.0

493

IS 1285 (2023) - Wrought Aluminium and Aluminium Alloys — Extruded Round Tube and Hollow Sections for General Engineering Purposes

Wrought Aluminium and Aluminium Alloys — Extruded Round Tube and Hollow Sections for General Engineering Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Chemical Analysis (as per IS 733))	5000.0
10 (Tensile Strength (as per IS 733))	1000.0
8 (Dimension)	1000.0
10 (0.2 % Proof Stress (as per IS 733))	1000.0
10 (% Elongation (as per IS 733))	1000.0
6 (Freedom from Defect)	1000.0
4 (Mass per meter)	1000.0
10.1 (Tensile strength test as per IS 1608 (Part 1):2022, N/mm2)	3000.0
4 (Anodic coating thickness, micron)	2000.0

494

IS 4923 (2017) - Hollow steel sections for structural use - Specification (Third Revision)

Hollow steel sections for structural use - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Sulphur, % by mass)	500.0
15.2 (Elongation, %)	1000.0
15.2 (Yield Strength, MPa)	1000.0
15.2 (Tensile Strength, MPa)	1000.0
9.1 (Dimension, mm)	1000.0
9.1 (Weight, kg/m)	1000.0
10.4 (Concavity and Convexity)	1000.0
10.5 (Squareness of sides, degree)	1000.0
7.1 (Phosphorus, % by mass)	500.0
15 (Tensile Strength for Hot formed sections, MPa)	1000.0
15 (Yield Strength for Hot formed sections, MPa)	1000.0
0 (Tensile strength test & Yield Strength Test, MPa)	5000.0
0 (Charpy Impact Test)	5000.0

495

IS 3316 (1974) - Structural Granite

Structural Granite

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Water Absorption)	1000.0
3.2 (Specific Gravity)	1000.0

496

IS 2185 : Part 3 (1984) - Concrete Masonry Units Part 3 Autoclaved Cellular Aerated Concrete Blocks

Concrete Masonry Units Part 3 Autoclaved Cellular Aerated Concrete Blocks

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.4 (Compressive Strength, in N/mm²)	12000.0
8.3 (Block Density, kg/m³)	1000.0
8.2 (Dimensions (Length, width and thickness))	3000.0
5 (Moisture Content (as received condition), on the lines of IS 6441, %)	1000.0
8.6 (Drying Shrinkage, in %)	1000.0
8.5 (Thermal Conductivity)	5000.0

497

NTH/NR/RPPT/CSD/Plastic (2022) - CSD-specification for Plastic Products

CSD-specification for Plastic Products

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.1 (Nomenclature of the Item)	1000.0
1.2 (Dimensions)	1000.0
1.3 (Colour)	1000.0
1.4 (Design)	1000.0
1.5 (Identification of Plastic)	5000.0
Firm's Requirement (Thickness)	1000.0

498

IS 5382 (1985) - Rubber Sealing Rings for Gas Mains, Water Mains and Sewers

Rubber Sealing Rings for Gas Mains, Water Mains and Sewers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.7.2 (Tensile Strength)	1000.0
3.7.2 (Elongation @Break)	1000.0
3.7.3 (Compression Set @70°C for 24 hrs.)	3000.0
3.7.3 (Compression Set @23°C for 72)	1999.0
3.7.3 (Compression Set @-10°C for 72 hrs.)	2999.0
3.7.4 (Change in Hardness after ageing at 70°C for 168 hrs.)	2000.0
3.7.4 (%Change in Tensile Strength after ageing at 70°C for 168 hrs.)	1500.0
3.7.4 (%Change in Elongation at break after ageing at 70°C for 168 hrs.)	1500.0
3.7.5 (Water Immersion Test)	3000.0
3.7.1 (IRHD Hardness)	1000.0

499

IS:8362Cl:4.1 Table 1 (1977) - Copper & Copper Alloy Rolled Platesfor Condensors & Heat Exchangers

Copper & Copper Alloy Rolled Platesfor Condensors & Heat Exchangers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS:8362 Cl 4.1 Table 1 (Please see Annexure.)	10000.0

500

ANSI B16.5 (2020) - Pipe Flanges and Flanged Fittings

Pipe Flanges and Flanged Fittings

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Thickness)	1000.0
6 (Bore Diameter)	1000.0
5 (Chemical Composition)	2500.0

501

ASTM A234 (2018) - Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service

Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 (Chemical Composition)	-
9 (Tensile strength)	1000.0
9 (Yield Stress)	1000.0
9 (Elongation Percent)	1000.0
13 (Outside diameter)	1000.0
13 (Thickness)	1000.0

502

ASTM 106 (2010) - Standard specification for Seamless Carbon Steel Pipe for high temperature service

Standard specification for Seamless Carbon Steel Pipe for high temperature service

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Chemical Composition)	5000.0
9 (Yield Stress)	1000.0
9 (Percent elongation at 5.65 of sq. root of Area)	1000.0
10 (Brinell Hardness test)	2000.0
9 (Tensile Strength)	1000.0

503

NTH/NR/CHEM/CUST-01 BATTERY PLATES (2022) - BATTERY PLATES FOR Lead TESTING

BATTERY PLATES FOR Lead TESTING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.1 (Lead Oxide in formed positive plate)	1200.0
1.2 (Free Lead Content)	1200.0
1.3 (Lead Sulphate content)	1200.0

504

IS 456 (2000) - Plain and reinforced concrete - WATER FOR CONSTRUCTION (Fourth Revision)

Plain and reinforced concrete - WATER FOR CONSTRUCTION (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.4 (pH)	500.0
5.4 (Volume (in ml) of 0.02 (N) H2SO4 required for Neutralization of 100 ml water using mixed indicator.)	500.0
5.4 (Volume (in ml) of 0.02 (N) NaOH required for Neutralization of 100 ml water using phenolphthalein as an indicator.)	500.0
5.4 (Suspended Matter)	500.0
5.4 (Chlorides (as Cl))	1000.0
5.4 (Sulphates ( as SO3))	1000.0
5.4 (Total Inorganic Solids)	500.0
5.4 (Total Organic Solids)	500.0
5.4.1.2 (Test for Compressive strength (IS 516))	4000.0
5.4.1.3 (Initial setting time of test block with sample water compared with distilled water(IS 4031 (Part 5):1988)	2000.0

505

NTH/NR/RPPT/CSD/Fabric (2022) - Fabric or Textiles Finished Product Specification

Fabric or Textiles Finished Product Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.1 (Nomenclature of the item)	1000.0
1.2 (Dimensions)	1000.0
1.3 (Design)	1000.0
1.4 (Identification)	1000.0
1.5 (Color)	1000.0
1.7 (Count of Yarn)	2000.0
1.8 (Ends and Picks)	999.0
1.12 (Dimensional Changes)	2000.0
1.9 (Color Fastness to Light)	3000.0
1.10 (Color Fastness to Washing)	2000.0
1.11 (Color Fastness to Perspiration)	2000.0
1.6 (Blend Composition)	3000.0
1.14 (Type of Yarn)	1000.0
1.15 (Weight)	1000.0
1.16 (pH of Aqueous Extract)	1000.0
Firm's Requirement (Thermal Insulation Resistance Test)	5000.0

506

IS 2312 (1967) - Specification for propeller type AC ventilating fans (First Revision)

Specification for propeller type AC ventilating fans (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Terminology)	-
3 (Sizes)	-
4 (Rated Voltage)	100.0
5 (Rated Frequency)	100.0
6 (Design and General Construction)	100.0
7 (Finish)	100.0
8 (Insulating Materials)	-
9 (Speed Regulators)	100.0
10 (Starting)	100.0
11 (Interchangeability)	100.0
12 (Silent Operation)	100.0
13 (Marking)	100.0
14.2 (Air Delivery Test at 230 V, AC,50 Hz. , Air delivery in m³/hr)	7500.0
14.3 (Temperature Rise Test )	2000.0
14.11 (Test for speed and Input at 230 V, 50 Hz.)	1000.0
14.11 ((i) Input in watts )	500.0
14.6 ((ii) Power factor )	500.0
14.12 ((iii) Maximum speed in r.p.m )	500.0
14.7 (Leakage current Test Leakage Current measured in µA)	600.0
14.8 (High Voltage Test At 1500 volts rms 50Hz for one minutes for Motor between live parts and body.)	1000.0
14.9 (Insulation Resistance test At 500 V DC Insulation Resistance between point of application of high voltage Fan motor.)	1000.0
14.1 (Test for Earthing connection Measured earth resistance in ohms)	500.0
14.13 (Flash Test)	-

507

9738 (2003) - Polyethylene bag for general purpose

Polyethylene bag for general purpose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3 (Average thickness)	1000.0
5 (Printing Ink Adhesion test)	1000.0

508

IS 778 (1984) - Specification for 2010 copper alloy gate, globe and check valves for waterworks purposes (Fourth Revision)

Specification for 2010 copper alloy gate, globe and check valves for waterworks purposes (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 Table 1 IS: 318 (Chemical Composition (Please see Annexure. NABL))	8000.0
8.1 Table 1 IS: 319 (Chemical Composition (Please see Annexure. NABL))	8000.0
IS:1264 Cl 7.1 Table 1 (Chemical Composition (Please see Annexure. NABL))	9000.0
IS:1264 ;IS: 7.1 Table 1 Chemical Composition (Chemical Composition (Please see Annexure.NON- NABL))	1.0
IS:318 ;3.1 Table 1 Chemical Composition (Chemical Composition (Please see Annexure.NON- NABL))	1.0
8.1 Table 1 IS: 319 Chemical Composition (Chemical Composition (Please see Annexure.) NON NABL)	1.0

509

IS 694 (2010) - Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 1100 v (Fourth Revision)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 1100 v (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Acceptance Tests (Conductor resistance test,Test for thickness of insulation,Tensile strength and elongation at break of insulation,Insulation resistance test,High voltage test ,Flammability test ,Oxygen index test ,Test for temperature index , Test for halogen acid gas evaluation and Test for smoke density rating ))	30000.0
5 (The insulation shall be of polyvinyl chloride compound of a) Type A — Cables for fixed installation b) Type C — Heat-resistant cables (HR) c) Type D — Flexible cables and cords The insulation shall be so applied that it fits closely on the conductor. It shall be possible to remove it without damage to the insulation itself, to the conductor)	-
6 (Filler: Material & Application The fillers shall be composed of one of the following or of any combination of the following: a) A compound based on unvulcanized rubber or plastics; or b) Natural or synthetic textiles; or c) Paper; or d) PVC)	-
7 (Binder tape (Binder tape shall consist of plastic or proof textile material.))	-
8 (Sheath: Material, Colour & application of sheath The sheath shall be polyvinyl chloride compound of the type specified for each type of cable as given below: a) Type ST1 — cables for fixed installations b) Type ST2 — cables sheathed with 85°C HRPVC compound c) Type ST3 — flexible cables)	-
9 (Ovality)	-
12 (Core identification)	-
13 (Cable code)	-
15 (Packing and Marking)	-
Table 1. iii. a. 1 (Annealing test for copper (core 1))	500.0
Table 1. iii. a. 2 (Tensile test for Aluminium(core 1))	500.0
Table 1. iii. a. 3 (Wrapping test for Aluminium)	500.0
Table 1. iii. a. 4 (Conductor resistance test (core 1))	1500.0
Table 1. iii. a. 5 (Persulphate test (for tinned copper conductor only))	1000.0
Table 1. iii. b (Test for overall dimension and thickness of insulation/sheath)	1000.0
Table 1. iii. b(2) (Minimum thickness of insulation (Core 1))	500.0
Table 1. iii. b(3) (Average thickness of sheath)	-
Table 1. iii. b(4) (Minimum thickness of sheath)	-
Table 1. iii. b(5) (Overall dimension)	500.0
Table 1. iii. c.1(1) (Tensile strength for insulation(Core 1))	1000.0
Table 1. iii. c.1(2) (Percentage elongation for insulation (Core 1))	1000.0
Table 1. iii. c.2 (Loss of mass test for insulation (Core 1))	500.0
Table 1. iii. c.3(1) (Tensile strength test after ageing for insulation(Core 1))	500.0
Table 1. iii. c.3(2) (Percentage elongation after ageing for insulation(Core 1))	500.0
Table 1. iii. c.3(3) (Variation of tensile strength after ageing for insulation(Core 1))	-
Table 1. iii. c.3(4) (Variation in percentage elongation after ageing for insulation (Core 1))	-
Table 1. iii. c.4 (Shrinkage test for insulation(Core 1))	500.0
Table 1. iii. c.5 (Heat shock test for insulation(Core 1))	250.0
Table 1. iii. c.6 (Hot deformation test for insulation(Core 1))	250.0
Table 1. iii. c.7 (Thermal stability test for insulation(Core 1))	500.0
Table 1. iii. c.8 (Cold bend test for insulation(Core 1))	1000.0
Table 1. iii. c.9 (Cold impact test for insulation(Core 1))	1000.0
Table 1. iii. c.10(1) (Flammability test for insulation-Unaffected portion from the lower edge the top clamp(Core 1))	500.0
Table 1. iii. c.10(2) (Flammability test for insulation-Period of burning (Core 1))	750.0
Table 1. iii. c.11 (The Oxygen index for insulation(Core 1))	5000.0
Table 1. iii. c.12 (Test temperature index for insulation(Core 1))	5000.0
Table 1. iii. c.13 (Test for halogen acid gas evaluation for insulation (Core 1))	5000.0
Table 1. iii. c.14 (Smoke density test for insulation (Core 1))	5000.0
Table 1. iii. d.1(1) (Tensile strength for sheath)	-
Table 1. iii. d.1(2) (Elongation test for sheath)	-
Table 1. iii. d.2 (Loss of mass test for sheath)	-
Table 1. iii. d.3(1) (Tensile strength after ageing for sheath)	-
Table 1. iii. d.3(2) (Percentage Elongation after ageing for sheath)	-
Table 1. iii. d.3(3) (Variation in tensile strength after ageing for sheath)	-
Table 1. iii. d.3(4) (Variation in percentage elongation after ageing for sheath)	-
Table 1. iii. d.4 (Shrinkage test for sheath)	-
Table 1. iii. d.5 (Heat shock test for sheath)	-
Table 1. iii. d.6 (Hot deformation test for sheath)	-
Table 1. iii. d.7 (Thermal stability for sheath)	-
Table 1. iii. d.8 (Oxygen index for sheath)	5000.0
Table 1. iii. d.9 (Test for temperature index for sheath)	5000.0
Table 1. iii. d.10 (Test for halogen acid gas evaluation for sheath)	5000.0
Table 1. iii. d.11 (Smoke density rating for sheath)	5000.0
Table 1. iii. d.12 (Cold bend test for sheath)	-
Table 1. iii. d.13 (Cold impact test(for sheath))	-
Table 1. iii. e.1(1) (High voltage test (water immersion test))	3000.0
Table 1. iii. e.1(2) (High voltage test DC (Core 1))	1000.0
Table 1. iii. e.3 , ii.g (Insulation resistance test)	2000.0
Table 1. iii. e.3 , ii.g (Insulation resistance test)	2000.0
Table 1. iii. e.3 , ii.g (Insulation resistance test)	2000.0
Table 1. iii. e.3 , ii.g (Insulation resistance test)	2000.0
Table 1. iii. e.4 (High voltage test (Cl. 10.2)(at room temperature))	1500.0
Table 1. iii. e.4(1) (Flammability Test on complete cable -Period of burning)	500.0
Table 1. iii. e.4(2) (Flammability test on complete cable-Unaffected portion)	750.0
Table 1. iii. e.5 (Additional Ageing Test (for Cables for Outdoor Use))	3000.0
Table 1. iii. e.5(1) (High Voltage Test after additional ageing)	-
Table 1. iii. e.5(2) (Cold bend or cold impact test after additional ageing)	-
Table 1. iii. (Type tests)	40000.0
Table-1,Sl.No(ii) (Core identification,Cable code,Packing and Marking,Conductor resistance test,Test for thickness of insulation,High voltage test AC (water immersion test) and Insulation resistance test.)	7500.0
-- (ILC Tests)	-
Sl.No.(ii),(g) (Insulation Resistance Test)	6000.0
SlNo(ii)(g) (Insulation Resistance Test-Single Core)	2000.0
-- (Insulation Resistance and Flammability)	2500.0
Tests (Conductor Resistance and Insulation Resistance Test)	3500.0
Tests (Tests)	20000.0
Insulation Resistance Test & Tensile strength and elongation at break (Insulation Resistance Test and Tensile strength and elongation at break)	3500.0
Test (Insulation Resistance and High Voltage Test)	5000.0
DAMB Tests (Tests)	29000.0
Test (Insulation Resistance Test)	8000.0
--- (Insulation Resistance and Flammability Tests)	6500.0
Tests (Conductor resistance test, Test for overall dimension and thickness of insulation/sheath, Test for halogen acid gas evaluation for insulation, Smoke density test for insulation, Insulation Resistance and High Voltage Test.)	17500.0
Additional Core(3core) (---)	6000.0
Type Tests,Category-01. (Tests)	20998.0

510

IS 428 (2013) - Washable distemper - Specification (Third Revision)

Washable distemper - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.7 i. (b) (Drying time b) Hard dry)	1500.0
6.7 ix (ix)Acc storage stability)	1500.0
6.7 viii (viii) Resistance to alkali)	1000.0
6.7 Vii (vii) Recoating properties)	1000.0
6.7 Vi (vi) Residue on sieve % by mass)	200.0
6.7 iii (iii)Finish)	500.0
6.7 ii (ii) Consistency)	1000.0
6.7 i. (a) (Drying time a) surface dry)	1500.0
6.7 iv (iv) Colour)	500.0
Clause 6.5 Table 1 (Please see Annexure)	10000.0