NTH - Management Information System

National Test House (NR), Ghaziabad

Kamla Nehru Nagar, Ghaziabad, Uttar Pradesh - 201002, Ghaziabad, Ghaziabad, Uttar Pradesh, 201002

7003775955 director-gzb[at]nth[dot]gov[dot]in

Scope List

Reset

608 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

541

13683 (2006) - Ring Spun Grey Cotton Yarn

Ring Spun Grey Cotton Yarn

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

542

IS 10733 (1983) - Tanker Hose of Rubber

Tanker Hose of Rubber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

543

IS 8329 (2000) - Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1.1 (External diameter)	1000.0
10.1.1 (Tensile Strength)	2000.0
10.1.1 (Percent Elongation)	1500.0
10.2 (Brinell Hardness)	2000.0
16.2 (C-2.3) (Bituminous Coating Test)	1000.0
15.3 (Ovality of pipe)	1000.0
16.3 (Thickness of Cement mortar lining of pipe)	1000.0
13.3 (Wall Thickness of pipe)	1000.0
13.2 (Bore Clearance of mortar lining in ductile iron pipe)	1000.0

544

CBIP 317 (2013) - Central Board of Irrigation & Power-Manual No-317- Single Phase Transformer

Central Board of Irrigation & Power-Manual No-317- Single Phase Transformer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Sec BB (3) (Magnetic Balance Test)	2000.0
Sec BB (3) (Measurement of unbalanced current)	2000.0
Sec BB (3) (Polarization lndex)	5000.0
Sec BB (3) (Voltage)	3000.0
Sec BB (3) (Unbalanced Current)	3000.0
17.3.2 (Permanent Deflection)	10000.0
17.3.1 (Permanent Deflection)	8000.0

545

IS 335 (1993) - NEW INSULATING OILS- SPECIFICATION

NEW INSULATING OILS- SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.5.2.6 (Measurernent of Break Down Voltage of trransformer Oil)	10000.0

546

IS 15652 (2006) - Insulating mats for electrical purposes - Specification

Insulating mats for electrical purposes - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.2.1 (Insulation Resistance with Water)	4000.0
8.2.2 (Leakage Current Test)	2500.0
8.2.3 (AC Dielectric Strength)	7000.0
8.2.4 (AC Proof Voltage)	3000.0
6.3 (Thickness)	500.0
8.4.2 (Low Temperature Resistance & High Voltage test)	4000.0
8.6 (Extreme low temperature test)	6000.0
8.1 (Tensile Strength and Elongation at Break)	1500.0
8.3 (Tensile Strength and Elongation at break After Ageing)	4000.0
8.5 (After Acid/Alkalis and Oil Resistance)	4500.0
8.4.1 (Flame Retardance)	2000.0
6.2 (Dimensions)	1000.0

547

IS 15769 (2008) - Flux Cored (Tubular) Electrodes for Gas Shielded and Self Shielded Metal welding of Carbon or Carbon Manganese Steel

Flux Cored (Tubular) Electrodes for Gas Shielded and Self Shielded Metal welding of Carbon or Carbon Manganese Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Diameter of Core Wire)	500.0
4.2 (Temper)	1000.0
4.2 (Cast)	500.0
4.2 (Helix)	500.0
4.3 (Uniformity)	500.0
4.4.3 (Spools, Overall Diameter A)	500.0
4.4.3 (Spools, Overall Width, B)	500.0
4.4.3 (Spools, Inner Diameter, C)	500.0
4.4.3 (Spools, Distance Between Axes D)	500.0
4.4.3 (Spools, Driving Hole Diameter E)	500.0
4.4.3 (Spools, Weight, Max)	500.0
5.8 (Chemical Analysis)	5000.0
5.2 (Radiographic Examination)	1500.0
5.3 (Tensile Test)	3000.0
5.4 (Charpy Impact Test)	3000.0
5.1.3.2 (Fillet Weld Fracture)	4000.0
5.1.3.2 (Dimension of Fillet Weld)	500.0
5.5 (Transverse Tensile Test)	3000.0
5.6 (Longitudinal Guided Bend Test)	1000.0
5.7 (Diffusible Hydrogen Test)	5000.0

548

IS 2026 : Part 1 (2011) - Power Transformers: Part 1 General (Second Revision)

Power Transformers: Part 1 General (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1.2(a) (Temperatur Rise)	20000.0
10.1.1(a) (Measurement of windlng Resistance)	1600.0
10.1.1(b) (Voltage ratio & Phase Displacement)	3200.0
10.1.1 (C) (% impedance and load loss)	12800.0
10.1.1(d) (No Load loss and current)	9600.0
10.1.1(e) (Separate source AC voltage withstand test)	4000.0
10.1.1(e) (Induced Overvoltage)	6400.0
10.1.2(b) (Lightning lmpulse Voltage test, Chopped impulse voltage test, Multi chopped irnpulse voltage test)	500000.0
10.1.3(d) (Measurement of Zero phase sequence impedance for 3 Phase transformer)	3000.0
10.1.3(g) (% Harmonics)	10000.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
10.1.3 (f) (Noise Level)	10000.0
7 (Rating Plate Details)	-
17.3.1 (a) of CBIP Pub. No. 317 (Pressure Test Routine (Deflection))	8000.0
17.3.2 (a) of CBIP Pub. No. 317 (Vacuum Test - Type (Deflection))	10000.0
17.3.2 (b) of CBIP Pub. No. 317 (Oil Leakage Test (Pressure Test - Type))	10000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	3000.0
As per IS : 335 (Breakdown Voltage Test)	10000.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0
10.1.2 (b) (Lightning Impulse Voltage Withstand Test upto 11 KV & 500 KVA Rating)	40000.0
10.1.2 (b) (Lightning Impulse Voltage Withstand Test upto 11 KV & 1000 KVA Rating)	50000.0
10.1.2 (b) (Lightning Impulse Voltage Withstand Test upto 11 KV & 2500 KVA Rating)	65000.0
10.1.2 (b) (Lightning Impulse Voltage Withstand Test For Power Transformers of 33 KV Class upto 20 MVA)	250000.0
10.1.3 (Measurement of Dissipation Factor (Tan Delta) & Capacitance)	10000.0

549

IS 2713 : PART 1 TO 3 (1980) - Tubular Steel Poles for Overhead Power Lines

Tubular Steel Poles for Overhead Power Lines

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.4 (Weight of Pole)	1000.0
15.1 (Dimension of Base Plate)	1000.0
8.1 (Outside Diameter (Top, Middle , Bottom Section of Pole))	3000.0
8.3 (Length (Overall Length, Top, Middle , Bottom Section of Pole))	4000.0
8.2 (Thickness (Top, Middle , Bottom Section of Pole))	3000.0
8.5 (Straightness)	1000.0
7 (Freedom from defect)	1000.0
10.1.3 (Deflection Test)	1000.0
10.1.4 (Permanent Set Test)	1500.0
10.1.5 (Drop Test)	1000.0
6 (Chemical Composition (Top, Middle , Bottom Section of Pole))	4500.0
11.2 of IS 1161: 2014 (Tensile Test (Top, Middle , Bottom Section))	9000.0
11.3.2 of IS 1161: 2014 (Flattening test (Top, Middle , Bottom Section of Pole))	3000.0
13.2 (Protection against corrosion (Galvanized Test))	2000.0

550

2026 (Part-11) (2021) - Specification for dry - Type power transformers

Specification for dry - Type power transformers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13.1.(a) (Measurement of Winding Resistance)	1000.0
13.1.(b) (Measurement of Voltage ratio & voltage vector relationship test)	2000.0
13.1.(c) (Measurement of lmpedance Voltage ,Short Circuit lmpedance and Load Loss)	8000.0
13.1.(d) (Measurement of No Load Loss & Current)	6000.0
13.1.(e) (Separate source Voltage withstand test)	2500.0
13.1.(f) (lnduced Over voltage withstand test)	4000.0
13.1(g) (Lightning Impulse Test)	65000.0
13.1.(h) (Temperature Rise Test)	40000.0
13.3.(b) (Measurement of acoustic sound Level)	7000.0

551

IS 4454 : Part 1 (2001) - Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 (Tensile Strength)	3000.0
9 (Dimensions)	1000.0

552

IS 15622 (2017) - Pressed Ceramic Tiles - Specification (First Revision)

Pressed Ceramic Tiles - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6, Tables 5 to 9, Sl No (iii), (a) (Resistance to staining IS 13630(8)/(7):2019)	1000.0
6, Tables 5 to 9, Sl No (iii), (b) (Resistance to household chemicals swimming pools, and water cleansers except to cleansing agents containing hydrofluoric acid and its compounds IS 13630(8)/(7):2019)	1000.0
6, Tables 5 to 9, Sl No (iii), (c) (Resistance to acid and alkalies (with exception of hydrofloric acid and its compounds-IS 13630(8)/(7):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (f) (Surface Quality-IS13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (a) (Dimensions-Length-IS13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (a) (Dimensions-Width -IS:13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (b) (Dimension-Thickness-Deviation in percent from work size -IS: 13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (d) (Rectangularity-Maximum deviation in percent to corresponding work size-IS: 13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (c) (Straightness of sides(Facial sides)Maximum deviation in percent to corresponding work size- IS13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (e-1,2,3) (Surface Flatness-Maximum deviation in percent from flatness-(Centre curvature, Edge curvature & warpage) -IS: 13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (ii), (a) (Water Absorption-IS13630 (Part 2):2019)	1000.0
6, Tables 5 to 9, Sl No (ii), (b) (Modulus of rupture in N/mm²- IS13630 (Part6):2019)	2000.0
6, Tables 5 to 9, Sl No (ii), (c) (Breaking of strength in N- IS13630 (Part 6):2019)	2000.0
6, Tables 5 to 9, Sl No (ii), (e) (Scratch Hardness of surface (Mohs' Scale)-IS13630 (Part 13):2019)	2000.0
6, Tables 5 to 9, Sl No (ii), (j) (Crazing Resistance- IS13630 (Part 9):2019)	1500.0
6, Tables 5 to 9, Sl No (ii), (k) (Impact resistance-Coefficient of Restitution-IS13630 (Part 14):2019)	1000.0
6, Tables 8 and 9, Sl No (ii), (q) (Bulk Density-IS13630 (Part 2):2019)	1000.0
6, Table 9, Sl No (iii), (a, b, c)-1(Part 8) (Chemical properties-glazed- IS13630 (Part 8):2019)	5000.0

553

IS 1237 (2012) - Cement Concrete Flooring Tiles - Specification

Cement Concrete Flooring Tiles - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.6 (Wet transverse strength-Annex F of IS 1237:2012)	2000.0
12.5 (Water Absorption-Annex E of IS 1237:2012)	1000.0
12.4 (Straightness-Annex D of IS 1237:2012)	500.0
12.3 (Perpendicularity-Annex C of IS 1237:2012)	500.0
10 (General Quality-IS 1237:2012)	100.0
8.3 & Table2 (The thickness of Wearing Layer-IS 1237:2012)	100.0
7, 8.2 & Table1 (Thickness & Tolerances-IS 1237:2012)	100.0
7 & 8.1, Table1 (Dimensions & Tolerances-IS 1237:2012)	200.0
12.7 (Resistance to wear-Annex G of IS 1237:2012)	2500.0

554

IS 10262 (2019) - Concrete Mix Proportioning — Guidelines ( Second Revision )

Concrete Mix Proportioning — Guidelines ( Second Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Concrete Mix design (IS 10262:2019) with Admixture)	35000.0
1 (Concrete Mix Proportioning — Guidelines (without admixture))	30000.0

555

IS 1489 : Part 2 (2015) - Portland - Pozzolana cement - Specification: Part 2 calcined clay based

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7, Table 2, Sl No 6 (Drying Shrinkage IS 4031(10):1988)	1000.0
7, Table 2, Sl No 4c (28 Days Compressive strength, MPa- IS 4031(6):1988)	1000.0
7, Table 2, Sl No 4b (7 Days Compressive strength,168±2 h, MPa- IS 4031(6):1988)	1000.0
7, Table 2, Sl No 4a (3 Days Compressive strength,72±1 , MPa- IS 4031(6):1988)	1000.0
7, Table 2, Sl No 3b (Setting time-Final, IS 4031(5):1988)	250.0
7, Table 2, Sl No 3a (Setting time- Initial IS 4031(5):1988)	250.0
7, Table 2, Sl No 2b (Soundness-autoclave method IS 4032(3):1988)	1000.0
7, Table 2, Sl No 2a (Soundness-Lechatlier method IS 4032(3):1988)	500.0
6, Table 1, Sl No 6 (Alkali content IS 4032:1985)	2000.0
6, Table 1, Sl No 5 (Chloride content IS 4032:1985)	800.0
6, Table 1, Sl No 4 (Loss on Ignition IS 4032:1985)	800.0
6, Table 1, Sl No 3 (Total Sulphur content IS 4032:1985)	800.0
6, Table 1, Sl No 2 (Magnesia IS 4032:1985)	800.0
6, Table 1, Sl No 1 (Insoluble residue IS 4032:1985)	800.0

556

IS 16227 : Part 1 (2016) - Instrument transformers: Part 1 general requirements

Instrument transformers: Part 1 general requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2.3.2 (Multi chopped (100) Lightning Impulse Voltage Test (CT / PT ) 220 KV Class)	150000.0
7.2.3.2 (Multi chopped (100) Lightning Impulse Voltage Test (CT / PT ) 132 KV Class)	100000.0

557

IS 1489 (Part 1) (2015) - Portland pozzolana cement - Specification: Part 1 fly Ash Based

Portland pozzolana cement - Specification: Part 1 fly Ash Based

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7, Table 2, Sl No 1 (Fineness IS 4031(2):1999)	1000.0
7, Table 2, Sl No 6 (Drying Shrinkage IS 4031(10):1988)	1000.0
7, Table 2, Sl No 4c (28 Days Compressive strength, IS 4031(6):1988)	1000.0
7, Table 2, Sl No 4b (7 Days Compressive strength, IS 4031(6):1988)	1000.0
7, Table 2, Sl No 4a (3 Days Compressive strength, IS 4031(6):1988)	1000.0
7, Table 2, Sl No 3b (Setting time-Final IS 4031(5):1988)	250.0
7, Table 2, Sl No 3a (Setting time-Initial IS 4031(5):1988)	250.0
7, Table 2, Sl No 2b (Soundness-autoclave method IS 4031(3):1988)	1000.0
7, Table 2, Sl No 2a (Soundness-Lechatlier method IS 4031(3):1988)	500.0
6, Table 1, Sl No 6 (Alkali content IS 4032:1985)	2000.0
6, Table 1, Sl No 5 (Chloride content, IS 4032:1985)	800.0
6, Table 1, Sl No 4 (Loss on ignition IS 4032:1985)	800.0
6, Table 1, Sl No 3 (Total Sulphur content IS 4032:1985)	800.0
6, Table 1, Sl No 2 (Magnesia IS 4032:1985)	600.0
6, Table 1, Sl No 1 (Insoluble residue, IS 4032:1985)	600.0
13 (Consistency of Cement)	500.0

558

IS 15658 (2021) - Concrete Paving Blocks - Specification ( First Revision )

Concrete Paving Blocks - Specification ( First Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3, Table 3, Sl No (iii) (Abrasion Resistance-(Wet condition)-IS 15658:2021, Annex E)	4000.0
7.3, Table 3, Sl No (iii) (Abrasion Resistance-(Dry condition)-IS 15658:2021, Annex E)	4000.0
7.3, Table 3, Sl No (iv) (Tensile Splitting Strength-IS 15658:2021, Annex F)	4000.0
7.3, , Table 3, Sl No (v) (Flexural strength-IS 15658:2021, Annex G)	4000.0
7.3, Table 3, Sl No (i) (Water Absorption-IS 15658:2021, Annex C)	1000.0
7.3, Table 3, Sl No (ii) (Compressive Strength-IS 15658:2021, Annex D)	4000.0
7.1 (General quality & Finish-IS 15658:2021)	1000.0
7.2, Table2 (Dimensions & Tolerances-IS 15658:2021, Annex B)	3000.0
3.2 (Thickness (Average Value), mm)	1000.0

559

IS 516 : Part 4 (2018) - Hardened Concrete -Methods of Test -Part 4, Sampling, Preparing and Testing of Concrete Cores ( First Revision ) ( IS 516 :(Part 4):2018)

Hardened Concrete -Methods of Test -Part 4, Sampling, Preparing and Testing of Concrete Cores ( First Revision ) ( IS 516 :(Part 4):2018)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 (Equivalent Cube Strength of core samples with preparation, N/mm^2)	5000.0

560

IS 13801 (2013) - Chequered Cement Concrete Tiles -

Chequered Cement Concrete Tiles -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.6 (Resistance to wear)	2000.0
12.5 (Wet transverse strength)	2000.0
12.4 (Water Absorption)	1000.0
12.3 (Straightness)	500.0
12.2 (Perpendicularity)	500.0
12.1 (Flatness)	500.0
10 (General Quality)	100.0
8.3 (Thickness of Wearing Layer)	500.0
7 (Dimension: Thickness)	1000.0
7.1,Table 1,Column 2 (Dimensions -Length)	300.0

561

IS 4000 (1992) - Code for practice for High strength bolts in steel structures

Code for practice for High strength bolts in steel structures

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.4.1 (Slip Factor - Surface Not Treated - consideration of 3 Specimens)	18000.0

562

IS 2074 (2015) - Ready Mixed Paint, Air Drying, Red Oxide - Zinc Chrome, Priming - Specification

Ready Mixed Paint, Air Drying, Red Oxide - Zinc Chrome, Priming - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.6, xii (Keeping properties)	5000.0
5.6,xi (Accelerated storage stability test)	200.0
5.1.1.a (chromic anhydride)	1000.0
5.1.1.b (Synthetic red oxides of iron red oxide (as Fe2O3))	1000.0
5.1.a (Pigment, percent by mass)	1200.0
5.1.1.a (zinc oxide)	500.0
5.6,vi (Colour)	50.0
5.6,i. a (Consistency)	200.0
5.6,iii.a (Drying: Surface dry)	100.0
5.6,iii.b (Drying: hard dry)	100.0
5.6,v (Fineness of grind, microns)	100.0
5.6,vii.b (Flexibility and adhesion: Scratch hardness (load 1000g))	100.0
5.6,iv.b (Gloss, 60º)	100.0
5.6,ii (Mass, kg/10litre)	200.0
5.6,i. b (Viscosity by Ford cup No. 4 at 27 ± 2°C)	200.0
5.6,viii (Flash point)	500.0
5.6,ix (Volume solids)	200.0
5.6,vii.a (Flexibility and adhesion:Bend test (with 6.25 mm dia mandrel and in type 1 apparatus))	100.0
5.6,x.c (Resistance to salt spray)	500.0
5.6,x.a (Resistance to humidity)	2500.0
5.5 (Lead Restriction)	200.0

563

IS 1077 (1992) - Common burnt clay building bricks - Specification (Fifth Revision)

Common burnt clay building bricks - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3 (Efflorescence IS 3495 (Part 3) : 2019)	1000.0
7.2 (Water Absorption IS 3495 (Part 2) : 2019)	1000.0
7.1 (Compressive Strength-IS 3495 (Part 1) : 2019)	2000.0
6 (DIMENSIONS AND TOLERANCES-IS 1077 : 1992)	500.0
5 (GENERAL QUALITY IS 1077 : 1992)	500.0

564

IS 745 (2021) - Textiles: Handloom cotton bed sheets

Textiles: Handloom cotton bed sheets

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (pH)	1000.0
5.2 (Scouring Loss)	2000.0
5.1 (Breaking Strength - Warp)	1500.0
5.1 (Mass)	1000.0
5.1 (Ends/dm)	500.0
4.1 (Composition of Yarn)	3000.0
5.1 (Breaking Strength - Weft)	1500.0
5.1 (Picks/dm)	500.0
Firm's Requirement (Water Soluble Matter)	2000.0
Firm's Requirement (Residual Starch Content)	2000.0

565

IS 1161 (2014) - Steel tubes for structural purposes - Specification (Fifth Revision)

Steel tubes for structural purposes - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.2 (Tensile Strength, MPa)	1000.0
11.2 (Yield Strength, MPa)	1000.0
11.2 (Percentage Elongation, %)	1000.0
6 (Mass per meter, kg/m)	1000.0
6 (Dimension)	1000.0
11.3.1 (Cold Bend Test up to 50 mm NB)	1000.0
11.3.2 (Flattening Test above 50 mm NB)	1000.0
7 (Workmanship)	1000.0
8 (Coating thickness, micron)	2000.0
5 (Chemical Composition)	2500.0
0 (Adhesion Test)	1000.0
0 (Mass of Zinc Coating)	2000.0
0 (Salt Spray Test)	60000.0

566

IS 1182 (1983) - Recommended - Practice for radiographic examination of fusion welded butt joints in steel plates (Second Revision)

Recommended - Practice for radiographic examination of fusion welded butt joints in steel plates (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 9.1 (Preparation of Weld assembly for Radiography test)	4000.0
Clause 9.1 of IS 814:2004 (Weld Assembly Preparation For Radiography Test)	5000.0
9.6 (Radiographic Test)	2000.0

567

IS 814:2004 - Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.6 (Radiographic Test-IS 1182)	1000.0
9.1.1 (Preparation of Weld assembly)	4000.0
9.1.1 (Preparation of Weld Assembly (For Radiography Test))	5000.0
8.2 (Combined limit for Mn+Ni+Cr+Mo+V)	500.0
8.2 (Vanadium)	500.0
8.2 (Molybdenum)	500.0
8.2 (Chromium)	500.0
8.2 (Nickel)	500.0
8.2 (Phosphorus)	500.0
8.2 (Sulphur)	500.0
8.2 (Manganese)	500.0
8.2 (Silicon)	500.0
8.2 (Carbon)	500.0
9.5 (Diffusible Hydrogen Evaluation Test-IS 11802)	5000.0
5.1.2 (Efficiency (EE) as per IS 13043)	4000.0
9.2 (Butt Weld Bend Test -IS 1599)	8000.0
9.1.3 (Impact Strength-Annex F)	3000.0
9.1.2 (Percentage Elongation on Gauge Length-Annex F)	1000.0
9.1.2 (Yield Stress -Annex F)	1000.0
9.1.2 (Ultimate Tensile Strength -Annex F)	1000.0
7.3 (Concentricity of Flux Covering With Core Wire)	250.0
7.2.2 (Arc striking End)	500.0
7.2.1 (Contact End)	500.0
7.1.2 (Length of Electrode)	500.0
9.5 (Diffusible Hydrogen Evaluation Test-IS 11802)	5000.0
7.4 (Defects of Core Wire and Coverings)	250.0
B7 (Coating Ratio)	500.0
9.3 (Running Performance Test)	2000.0

568

IS 14587 (1998) - Prelaminated Medium Density Fibre Board -specification

Prelaminated Medium Density Fibre Board -specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.14 (Resistance to Stain-IS 14587:1998 Annex F)	1500.0
10.13 (Resistance to Cigarette Burn-IS 14587:1998 Annex E)	500.0
10.12 (Resistance to Crack-IS 14587:1998 Annex D)	500.0
10.11 (Resistance to Steam-IS 14587:1998 Annex C)	500.0
10.10, Table 1, Sl No 1.9 (Resistance to Surface Abrasion-IS 14587:1998 Annex B)	5000.0
10. 9, Table 1, Sl No 1.8 (Screw Withdrawal Test -IS 2380 (Part 14):1977)	1500.0
10. 8, Table 1, Sl No 1.7 (Tensile strength perpendicular to surface after ageing-IS 14587:1998 & -IS 2380 (Part 5):1977)	2000.0
10.7, Table 1, Sl No 1.6 (Tensile strength perpendicular to surface-IS 2380 (Part 5):1977)	2000.0
10.6, Table 1, Sl No 1.4 & 1.5 (Modulus of Rupture and Modulus of Elasticity-IS 2380 (Part 4):1977)	2500.0
10.5,Table 1, Sl No 1.3 (Thickness swelling-IS 2380 (Part 17):1977)	1500.0
10.4, Table 1, Sl No 1.2 (Water Absorption-IS 2380 (Part 16):1977)	1000.0
10.3 (Moisture Content-IS 2380 (Part 3):1977)	1000.0
10.2, Table 1, Sl No 1.1 (Density-IS 2380 (Part 3):1977)	500.0
8 (Dimension & Tolerances-IS 12406)	500.0

569

IS 12823 (2015) - Wood Products - Prelaminated Particle Boards -Specification

Wood Products - Prelaminated Particle Boards -Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.14 (Resistance to Stain-IS 12823:2015 Annex G)	1500.0
10.13 (Resistance to Cigarette Burn-IS 12823:2015 Annex F)	500.0
10.12 (Resistance to Crack-IS 12823:2015 Annex E)	500.0
10.11 (Resistance to Steam-IS 12823:2015 Annex D)	500.0
10.10 Table 2, Sl No (ix) (Abrasion Resistance-IS 12823:2015 Annex C)	5000.0
10.9, Table 2, Sl No (viii) (Screw Withdrawal Strength -IS 2380 (Part 14):1977)	1500.0
10.8, Table 2, Sl No (vii) (Tensile strength perpendicular to surface after ageing-IS 12823:2015 &-IS 2380 (Part 5):1977)	2000.0
10.7 Table 2, Sl No (vi) (Tensile strength perpendicular to surface-IS 2380 (Part 5):1977)	2000.0
10.6Table 2, Sl No (v) (Modulus of Rupture & Modulus of Elasticity-IS 2380 (Part 4):1977)	2500.0
10.5 Table 2, Sl No (iv) (Swelling in Water-IS 2380 (Part 17):1977)	1000.0
10.4 Table 2, Sl No (iii) (Water Absorption-IS 2380 (Part 16):1977)	1000.0
10.3 (Moisture Content-IS 2380 (Part 3):1977)	1000.0
10.2, Table 2, Sl No (i) & (ii) (Density-IS 2380 (Part 3):1977)	500.0
8 (Dimension & Tolerances-IS 12823:2015 Annex B)	500.0

570

IS 3087 (2005) - Practicle boards of wood and other lingnocellulosic materials (medium density) for general purposes -Specification

Practicle boards of wood and other lingnocellulosic materials (medium density) for general purposes -Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.9.1, Table 1, Sl No.(ix), a & b (Tensile strength perpendicular to surface after cyclic/accelerated water resistance test-IS 2380 (Part 5):1977)	2000.0
11.10, Table 1, Sl No.(x) (Screw Withdrawal Strength-IS 2380 (Part 14):1977)	1500.0
11.9, Table 1, Sl No.(viii) (Tensile strength perpendicular to surface-IS 2380 (Part 5):1977)	2000.0
11.8, Table 1, Sl No.(vi) & (vii) (Modulus of Rupture and Modulus of Elasticity-IS 2380 (Part 4):1977)	2500.0
9.6 (Workability-IS 3087:2005)	2000.0
9.5 & 11.7Table 1, Sl No.(v) , (Swelling due to surface absorption-IS 2380 (Part 17):1977)	2000.0
9.4 & 11.6, Table 1, Sl No.(iii) & (iv) (Swelling in water-IS 2380 (Part 17):1977)	1500.0
9.3 & 11.5, Table 1, Sl No.(ii) (Water Absorption-IS 2380 (Part 16):1977)	1000.0
9.2 & 11.4 (Moisture content-IS 2380 (Part 3):1977)	1000.0
9.1 & 11.3, Table 1, Sl No.(i) (Density-IS 2380 (Part 3):1977)	500.0
8 and 11.2 (Dimensions and Tolerances-IS 2380 (Part 2):1977)	500.0