| 241 |
MORTH-5th revision 2013 -Wet Mix Macadam Sub-base/base - Specifications for Road and Bridge Works |
Specifications for Road and Bridge Works |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 406.2.1.1 (Water absorption) |
1000.0 |
|
| 406.2.1.1 (Soundness) |
2000.0 |
|
| 406.2.1.1 Table 400.12.1 (Los Angeles Abrasion value) |
1500.0 |
|
| 406.2.1.1 Table 400.12.1 (Aggregate Impact value) |
1500.0 |
|
| 406.2.1.1 Table 400.12.2 (Combined Flakiness and Elongation Indices (Total)) |
3000.0 |
|
| 406.2.1.2 Table 400.13 (Grading Requirements of Aggregates for Wet Mix Macadam) |
5000.0 |
|
| 406.2.1.2 (Plasticity Index (PI)) |
1000.0 |
|
| 406.2.1.2 (Liquid Limit) |
1000.0 |
|
| 406.2.1.2 (Plastic Limit) |
1000.0 |
|
|
| 242 |
IS 16415 (2015) - Composite cement - Specification |
Composite cement - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.1 (Alkali Content) |
1200.0 |
|
| 6.1 (Chloride content) |
1200.0 |
|
| 6.1 (Loss on ignition) |
1200.0 |
|
| 6.1 (Sulphide sulphur (S)) |
1200.0 |
|
| 6.1 (Total Sulphur content calculated as sulphuric anhydride(SO3)) |
1200.0 |
|
| 6.1 (Magnesia) |
1200.0 |
|
| 6.1 (Insoluble residue) |
1200.0 |
|
| 13 (Test for Consistency) |
500.0 |
|
| Table 3,i (Fineness) |
1000.0 |
|
| Table 3,ii,a (Soundness-by Le-chatelier method) |
500.0 |
|
| Table 3,ii,b (Soundness -by Autoclave method) |
500.0 |
|
| Table 3,iii,a (Setting Time-Initial) |
250.0 |
|
| Table 3,iii,b (Setting Time-Final) |
250.0 |
|
| Table-3 (Compressive strength - 24 h (±) 30 min) |
1000.0 |
|
| Table-3,iv,b (Compressive strength-168(±)2 h) |
1000.0 |
|
| Table-3,iv,c (Compressive strength-672(±)4 h) |
1000.0 |
|
| Table-3,v (Drying shrinkage) |
1000.0 |
|
| Table-3,iv,a (Compressive strength-72(±)1 h) |
1000.0 |
|
|
| 243 |
IRC 105:2019 (DBM+BC)/(ASTM D 2041/AASHTO T 166/ASTM D2172/ASTM D 6307) - Specification for Dense Bituminous Macadam and Bituminous content for airfield Pavements |
Specification for Dense Bituminous Macadam and Bituminous content for airfield Pavements |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of DBM core (Aashto T 166/ASTM D 2041)) |
3000.0 |
|
| 2 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of BC core (Aashto T 166/ASTM D 2041)) |
3000.0 |
|
| 3 (Bitumen content/Binder content of DBM core(ASTM D2172/ASTM 6307)) |
3000.0 |
|
| 4 (Bitumen content/Binder content of BC core(ASTM D2172/ASTM 6307/(IRC-SP-20-2002)) |
3000.0 |
|
| - (Binder content/Bitumen content -DBM(IRC-SP-20-2002)) |
3000.0 |
|
| - (Binder content/Bitumen content -DAC(IRC-SP-20-2002)) |
3000.0 |
|
| - (Binder content/Bitumen content -SDAC(IRC-SP-20-2002)) |
3000.0 |
|
| 1 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of DAC core (Aashto T 166/ASTM D 2041)) |
3000.0 |
|
| 1 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of SDAC core (Aashto T 166/ASTM D 2041)) |
3000.0 |
|
|
| 244 |
IRC 111-2009 (DBM) & AASHTO T 166 - Specifications for Dense graded Bituminous mixes-(DBM) |
Specifications for Dense graded Bituminous mixes-(DBM) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Test for Density/Bulk density/ Theoretical Maximum specific gravity/Bulk specific gravity:(Aaashto-T 166/ASTM D 2041)) |
3000.0 |
|
| 2 (Test for Bitumen/Binder content (ASTM 2172/ASTM D 6307/IRC:SP:20 (2002))) |
3000.0 |
|
|
| 245 |
IS 2720 (Soil) (1987) - Method of Test for Soil. |
Method of Test for Soil. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 246 |
IS 14543 (2024) - Packaged Drinking Water (other than Packaged Natural Mineral Water) - Specification |
Packaged Drinking Water (other than Packaged Natural Mineral Water) - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5.2.9 (Vibrio parahaemolyticus) |
1200.0 |
|
| 5.2.9 (Vibrio cholerae) |
1200.0 |
|
| 5.2.8 (Shigella) |
1200.0 |
|
| 5.2.8 (Salmonella) |
1200.0 |
|
| 5.2.7 (Yeast & Mould) |
1200.0 |
|
| 5.2.6 (Aerobic microbial count/ ml at 37° ± 1° C in 24 hours) |
1200.0 |
|
| 5.2.6 (Aerobic microbial count/ ml at 20-22 °C in 72 hours) |
1200.0 |
|
| 5.2.5 (Pseudomonas aeruginosa) |
1200.0 |
|
| 5.2.4 (Sulphite reducing Anaerobes) |
1200.0 |
|
| 5.2.3 (Staphylococcus aureus) |
1200.0 |
|
| 5.2.3 (Faecal Streptococci) |
1200.0 |
|
| 5.2.2 (Coliform) |
1200.0 |
|
| 5.2.1 (Escherichia coli) |
1200.0 |
|
| 5.3 (Total dissolved solids) |
1000.0 |
|
| 5.3 (Bromate (as BrO3)) |
1200.0 |
|
| 5.3 (Sulphate (as SO4)) |
1200.0 |
|
| 5.3 (Lead (as Pb)) |
1000.0 |
|
| 5.3 (Zinc (as Zn)) |
1000.0 |
|
| 5.3 (Aluminium (as Al)) |
1000.0 |
|
| 5.4.1 (Annex D) (o, p-DDT) |
5000.0 |
|
| 5.3 (Iron (as Fe)) |
1200.0 |
|
| Custom (Total Aerobic microbial count at 37 °C in 48 hrs or 72 hrs) |
1000.0 |
|
| Custom (Total Aerobic microbial count at 30 °C in 72 hrs) |
1000.0 |
|
| 5.3 (Copper (as Cu)) |
1200.0 |
|
| 5.3 (Manganese (as Mn)) |
1200.0 |
|
| 5.3 (Selenium (as Se)) |
1000.0 |
|
| 5.3 (Chromium (as Cr)) |
1000.0 |
|
| 5.3 (Nickel (as Ni)) |
1000.0 |
|
| 5.3 (Cadmium (as Cd)) |
1000.0 |
|
| 5.3 (Mercury (as Hg)) |
2000.0 |
|
| 5.3 (Colour, true colour units) |
1200.0 |
|
| 5.3 (Odour) |
1000.0 |
|
| 5.3 (Turbidity) |
1000.0 |
|
| 5.3 (pH) |
1000.0 |
|
| 5.3 (Barium (as Ba)) |
1000.0 |
|
| 5.3 (Nitrate (as NO3)) |
1000.0 |
|
| 5.3 (Nitrite (as NO2)) |
1000.0 |
|
| 5.3 (Fluoride (as F)) |
1000.0 |
|
| 5.3 (Silver (as Ag)) |
1000.0 |
|
| 5.3 (Chloride (as Cl)) |
1000.0 |
|
| 5.3 (Alkalinity (as HCO3)) |
1000.0 |
|
| 5.3 (Calcium (as Ca)) |
1000.0 |
|
| 5.3 (Magnesium (as Mg)) |
1000.0 |
|
| 5.3 (Sodium (as Na)) |
1000.0 |
|
| 5.3 (Residual free chlorine) |
1000.0 |
|
| 5.3 (Phenolic compounds (as C6H5OH)) |
1000.0 |
|
| 5.3 (Sulphide (as H2S)) |
1000.0 |
|
| 5.3 (Antimony (as Sb)) |
1000.0 |
|
| 5.3 (Borates (as B)) |
1000.0 |
|
| 5.3 (Arsenic (as As)) |
2000.0 |
|
| 5.3 (Cyanide (as CN)) |
2000.0 |
|
| 5.3 (Taste) |
1000.0 |
|
|
| 247 |
IS 1293 (2019) - Plugs and socket- outlets of rated Voltage up to and inculding 250 Volts and rated current up to and inculding 16 amperes-Specification(Fourth Revision) |
Plugs and socket- outlets of rated Voltage up to and inculding 250 Volts and rated current up to and inculding 16 amperes-Specification(Fourth Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 31.1 (Type Test (6A)) |
7000.0 |
|
| 31.1 (Type Test (16A)) |
10000.0 |
|
| 31.1 (Type Test (6A & 16A)) |
12000.0 |
|
| 31.2 (Acceptance Test (6A)) |
5000.0 |
|
| 31.2 (Acceptance Test (16A)) |
7000.0 |
|
| 31.2 (Acceptance Test (6A & 16A)) |
9000.0 |
|
|
| 248 |
MORTH-5th revision/ASTM (BC/DBM/BC+DBM Cores) - MORTH-5th revision/ASTM (BC/DBM/BC+DBM Cores) |
MORTH-5th revision/ASTM (BC/DBM/BC+DBM Cores) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 505.3.5 (Density(ASTM-D2726)) |
2000.0 |
|
| 505.3.5 (Binder content(ASTM-D 2172)) |
5000.0 |
|
|
| 249 |
CUS/SR/MECH-20 (2023) - Specification for Hanger Shackle, dia 25 mm for PGCIL |
Specification for Hanger Shackle, dia 25 mm for PGCIL |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Visual examination) |
1000.0 |
|
| 2.0 (Dimensions, mm) |
2000.0 |
|
| 3.1 (Tensile load, kN) |
1500.0 |
|
| 3.2 (Proof load, kN) |
1500.0 |
|
| 4.0 (Hardness) |
3000.0 |
|
| 7.0 (Chemical composition, % by mass) |
5000.0 |
|
| 5.1 (Thickness of Zinc coating) |
2000.0 |
|
| 5.2 (Mass of Zinc coating) |
2000.0 |
|
| 5.3 (Uniformity of Zinc coating) |
1000.0 |
|
| 9.1 (Grain size) |
3000.0 |
|
| 9.2 (Grain flow) |
3000.0 |
|
| 10.0 (Inclusion rating) |
4000.0 |
|
| 6.0 (Adhesion test) |
1000.0 |
|
| 8.0 (Magnetic particle inspection (after stripping of galvanization)) |
2000.0 |
|
|
| 250 |
IS 17876 (2022) - Stainless Steel Welded Pipes and Tubes for General Services - Specification |
Stainless Steel Welded Pipes and Tubes for General Services - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Clauses 8.1 and 8.2 (Carbon (as C)) |
1000.0 |
|
| Clauses 8.1 and 8.2 (Silicon (as Si)) |
1000.0 |
|
| Clauses 8.1 and 8.2 (Manganese (as Mn)) |
1000.0 |
|
| Clauses 8.1 and 8.2 (Nickel (as Ni)) |
1000.0 |
|
| Clauses 8.1 and 8.2 (Chromium (as Cr)) |
1000.0 |
|
| Clauses 8.1 and 8.2 (Molybdenum (as Mo)) |
1000.0 |
|
| Clauses 8.1 and 8.2 (Sulphur (as S)) |
1000.0 |
|
| Clauses 8.1 and 8.2 (Phosphorus (as P)) |
1000.0 |
|
| Customer request (Weight per meter, kg/m) |
1000.0 |
|
| 10.1 (Tensile Strength, MPa) |
1000.0 |
|
| 10.1 (Yield Strength, MPa) |
1000.0 |
|
| 10.1 (Percent Elongation, %) |
1000.0 |
|
| 24 (Outside Diameter, mm) |
1000.0 |
|
| 24 (Wall Thickness, mm) |
1000.0 |
|
| 8 (Chemical Composition - Ladle Analysis as per IS 228 and its relevant parts or any other established instrumental/chemical method) |
5000.0 |
|
|
| 251 |
IS 17875 (2022) - Stainless Steel Seamless Pipes and Tubes for General Services |
Stainless Steel Seamless Pipes and Tubes for General Services |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8.1 & 8.2 (Carbon) (Carbon (as C)) |
1000.0 |
|
| 8.1 & 8.2 (Silicon) (Silicon (as Si)) |
1000.0 |
|
| 8.1 & 8.2 (Manganese) (Manganese (as Mn)) |
1000.0 |
|
| 8.1 & 8.2 (Nickel) (Nickel (as Ni)) |
1000.0 |
|
| 8.1 & 8.2 (Chromium) (Chromium (as Cr)) |
1000.0 |
|
| 8.1 & 8.2 (Molybdenum) (Molybdenum (as Mo)) |
1000.0 |
|
| 8.1 & 8.2 (Sulphur) (Sulphur (as S)) |
1000.0 |
|
| 8.1 & 8.2 (Phosphorus) (Phosphorus (as P)) |
1000.0 |
|
| 10.1 (Tensile Strength) |
1000.0 |
|
| 10.1 (Yield Strength) |
1000.0 |
|
| 10.1 (Percent Elongation) |
1000.0 |
|
| 12 (HARDNESS TEST FOR TUBES) |
2000.0 |
|
| 8 (Chemical Composition) |
5000.0 |
|
|
| 252 |
IS 13730 : Part 27 (2018) - Specifications for Particular Types of Winding Wires Part 27 Paper Tape Covered Rectangular Copper Wire ( First Revision ) |
Specifications for Particular Types of Winding Wires Part 27 Paper Tape Covered Rectangular Copper Wire ( First Revision ) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.1 (Dimension of the conductor) |
500.0 |
|
| 5 (Conductor Resistance) |
1500.0 |
|
| 6 (Elongation) |
3000.0 |
|
| 4.4 (Increase in Diameter (Double paper covering)) |
500.0 |
|
| 3.2.2 (Grade of covering) |
- |
|
| 4.5 (Overall Dimension (Double paper covering)) |
500.0 |
|
|
| 253 |
Customer Specification - WPC - Customer Specification - WPC |
Customer Specification - WPC |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Customer Specified Test parameters (WPC)) |
14500.0 |
|
| 2 (Lead Content (by AAS method)) |
1000.0 |
|
| 3 (Surface Hardness Test (Indentation Test)) |
1000.0 |
|
| 4 (Vicat Softening Temperature, deg.C) |
1500.0 |
|
| 5 (Izod Impact Strength) |
2000.0 |
|
| 6 (Charpy Impact Strength) |
2000.0 |
|
| 7 (Compression Strength test) |
2000.0 |
|
| 8 (Shore (A/D) Hardness Test) |
1000.0 |
|
|
| 254 |
IS 3601 (2006) - Steel tubes for mechanical and general engineering purposes - Specification (Second Revision) |
Steel tubes for mechanical and general engineering purposes - Specification (Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 13.2 (Flattening test) |
1000.0 |
|
| 13.5 (Drift Expansion) |
1500.0 |
|
| 8 (Straightness) |
- |
|
| 6 (Visual examination) |
1000.0 |
|
| 13.1 (Tensile strength, MPa) |
1000.0 |
|
| 13.1 (Yield stress, MPa) |
1000.0 |
|
| 13.1 (% Elongation) |
1000.0 |
|
| 4 (Chemical composition, % by mass) |
2500.0 |
|
| 10 (Outside diameter, mm) |
1000.0 |
|
| 10 (Thickness, mm) |
1000.0 |
|
| 10 (Weight, kg/m) |
- |
|
|
| 255 |
IS 4923 (2017) - Hollow steel sections for structural use - Specification (Third Revision) |
Hollow steel sections for structural use - Specification (Third Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 10.4 (Concavity and Convexity) |
1000.0 |
|
| 15 (Tensile Strength for Hot formed sections, MPa) |
1000.0 |
|
| 15 (Yield Strength for Hot formed sections, MPa) |
1000.0 |
|
| 15 (Percentage of elongation for Hot formed sections, %) |
1000.0 |
|
| 9.1 (Weight, kg/m) |
1000.0 |
|
| 10.2 (Outside Dimension (B), mm) |
500.0 |
|
| 10.2 (Outside Dimension (H), mm) |
- |
|
| 10.3 (Thickness, mm) |
500.0 |
|
| 10.5 (Squareness of sides, degree) |
1000.0 |
|
| 10.7 (Straightness and Twist) |
1000.0 |
|
| 7 (Chemical Composition % by mass) |
1500.0 |
|
| 15.2 (Elongation, %) |
1000.0 |
|
| 15.2 (Yield Strength, MPa) |
1000.0 |
|
| 15.2 (Tensile Strength, MPa) |
1000.0 |
|
| TR-1 (Presence of Zinc) |
1000.0 |
|
| TR-2 (Coating thickness of inner and outer layers) |
2000.0 |
|
|
| 256 |
IS 10262 (2019) - Concrete Mix Proportioning — Guidelines ( Second Revision ) |
Concrete Mix Proportioning — Guidelines ( Second Revision ) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4 (Concrete Mix Design (IS 10262:2019)) |
35000.0 |
|
| 1 (Concrete Mix Proportioning — Guidelines (without admixture)) |
30000.0 |
|
|
| 257 |
28095 - TNTB & ESC Technical Specification for Wollen Sweater (Boys/Girls)- 2023 |
TNTB & ESC Technical Specification for Wollen Sweater (Boys/Girls)- 2023 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.1 (Test results (RPPT)) |
13900.0 |
|
| 1.2 (Test Results (Chemical)) |
9000.0 |
|
|
| 258 |
28085 - Customised Specification (Sika) for APP Membrane |
Customised Specification (Sika) for APP Membrane |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Test Results) |
29000.0 |
|
|
| 259 |
28087 - TNTB Technical Specification for Raincoat (Unisex)- 2023 |
TNTB Technical Specification for Raincoat (Unisex)- 2023 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Raincoat Test Results) |
4680.5 |
|
|
| 260 |
CUS/SR/MECH-19 (2023) - Manila Rope Slings |
Manila Rope Slings |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Breaking load) |
3000.0 |
|
|
| 261 |
CUS/SR/MECH-18 (2023) - Wooden step |
Wooden step |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Breaking load) |
3000.0 |
|
|
| 262 |
School Bag Cust TNTB & ESC (2023) - School Bag Cust TNTB & ESC (2023) |
School Bag Cust TNTB & ESC (2023) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (School Bag Test Result) |
10980.0 |
|
| 4.3.6 (Zip Material-Runner Handle base) |
540.0 |
|
| 4.3.7 (Runner Coating Thickness-Handle, micron) |
900.0 |
|
| 4.3.5 (Runner Coating Thickness -Head, micron) |
900.0 |
|
| 4.3.4 (Zip Material-Runner Head base) |
540.0 |
|
|
| 263 |
NTH/WI/MC (on the lines of IS 4169) 11 (2014) - Metallic Materials - calibration of force-proving instruments used for the verification of uniaxial testing machines |
Metallic Materials - calibration of force-proving instruments used for the verification of uniaxial testing machines |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.1 (Force (above 1000 kN to 2000 kN) and deflection measurement calibration) |
25000.0 |
|
|
| 264 |
Customer Specification-Paper (2023) - Cust Spfn Results of the Tests |
Cust Spfn Results of the Tests |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (GSM, g/sq.m) |
1000.0 |
|
| 2 (Burst Index Test) |
2000.0 |
|
| 3 (Tear Index Test) |
2000.0 |
|
| 4 (Tensile Index Test) |
2000.0 |
|
|
| 265 |
2595 (2008) - INDUSTRIAL RADIOGRAPHIC TESTING —CODE OF PRACTICE |
INDUSTRIAL RADIOGRAPHIC TESTING —CODE OF PRACTICE |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.1 (Radiographic Examination) |
2000.0 |
|
|
| 266 |
IS 4748 (2021) - Steels - Micrographic determination of the apparent grain size (Third Revision) |
Steels - Micrographic determination of the apparent grain size (Third Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| IS 4748 (Grain Size) |
3500.0 |
|
|
| 267 |
Customized Specification for EPDM Rubber (2023) - Customized Specification for EPDM Rubber |
Customized Specification for EPDM Rubber |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.1 (Hardness Shore A) |
1000.0 |
|
| 1.2 (Polymer Identification (FTIR Method)) |
2000.0 |
|
|
| 268 |
IS 4454 : Part 1 (2001) - Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision) |
Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 10.3 (Torsion Test) |
1000.0 |
|
|
| 269 |
IS 516 (Part 1/Sec 1) : 2021 (3 set CC cubes) - Hardened Concrete —Methods of Test
(Part 1 Testing of Strength of Hardened Concrete)
(Section 1 Compressive, Flexural and Split Tensile Strength) |
Hardened Concrete —Methods of Test
(Part 1 Testing of Strength of Hardened Concrete)
(Section 1 Compressive, Flexural and Split Tensile Strength) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3 (Compressive strength,MPa) |
3600.0 |
|
|
| 270 |
IS 17545: 2021 (2021) - WHITE CEMENT BASED POLYMERIC PUTTY |
WHITE CEMENT BASED POLYMERIC PUTTY |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.5 Table 1(iii) (Initial Setting time-Annex D in minutes) |
200.0 |
|
| 4.5 Table 1(iii) (Final Setting time-Annex D
in minutes) |
200.0 |
|
| 4.6 Optional requirement (Compressive strength, 28 days in N/mm2
(IS 4031 (Part 6))) |
3000.0 |
|
|
