NTH - Management Information System

National Test House (SR), Chennai

CSIR Road, Tharamani, Chennai - 600113, Chennai, Chennai, Tamil Nadu, 600113

9444380435 director-chn[at]nth[dot]gov[dot]in

Scope List

Reset

597 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

271

IS 8183:1993 - Bonded Mineral Wool

Bonded Mineral Wool

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1. (Description)	1000.0
4.2 (Bulk density (IS 3144 ))	1000.0
4.3 (Recovery after Compression(IS 3144))	1500.0
4.5 (Moisture content (IS 3144))	1000.0
4.5 (Moisture Absorption (IS 3144))	1000.0
4.8 (Sulphur content(IS 3144))	1000.0
4.9 (Dimension)	1000.0
4.10.2 (Odour emission test (IS 3144))	1000.0
4.10.6 (Alkalinity ( IS 3144))	1000.0

272

IS 9537 : Part 3 (1983) - Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

273

Custom-RVNL-TI/MI/040 (wef 05/04/2005) (2005) - Special Maintenance Instruction (SMI) to Measure the Severity of Pollution by Brush Wash Method

Special Maintenance Instruction (SMI) to Measure the Severity of Pollution by Brush Wash Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Salt deposit density (in mg/cm2))	2500.0

274

IS 1367 : Part 6 (2018) - Technical Supply Conditions for Threaded Steel Fasteners Part 6 Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel — Nuts with Specified Property Classes — Coarse Thread and Fine Pitch Thread

Technical Supply Conditions for Threaded Steel Fasteners Part 6 Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel — Nuts with Specified Property Classes — Coarse Thread and Fine Pitch Thread

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

275

IS 1367 : Part 6 (2018) - Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Hardness Test)	2000.0
7 (Proof Load)	3000.0
6 (Chemical composition, % by mass)	2500.0
7, Table 6 (Rockwell hardness, HRC)	2000.0

276

900173-Custom RO Salt (2023) - Customer Requirement on RO Salt Sample Analysis

Customer Requirement on RO Salt Sample Analysis

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (a) (Loss on Ignition (at 450 deg C) after 1 hour)	1200.0
1 (b) (Colour (after LoI at 450 deg C for 1 hour))	1200.0
2 (a) (Loss on Ignition (at 450 deg C) after 2 hours)	1200.0
2 (b) (Colour (after LoI at 450 deg C for 2 hours))	1200.0

277

Relevant Standards (2023) - Custom Tests Aluminium Composite

Custom Tests Aluminium Composite

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Weight (as such))	1000.0
2 (Dimension, Panel Width, mm)	500.0
3 (Dimension Panel Length, mm)	500.0
4 (Panel Thickness, mm)	1000.0
5 (Density at 27degC, g/cc)	1000.0
6 (Tensile Strength, kg/sq.mm)	1000.0
7 (Tensile Yield Strength, kg/sq.mm)	500.0
8 (Elongation, %)	500.0
9 (Flexural Strength, Kg/sq.mm)	2000.0
10 (Compressive Strength, MPa)	2000.0
11 (Water Absorption, %)	1000.0

278

DIN EN 12467 (July 2018) - Fibre-Cement Flat Sheets-Product specification and test methods

Fibre-Cement Flat Sheets-Product specification and test methods

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1.2 (Appearance & finish)	2000.0
5.2 (Classification)	2000.0
5.3.2 (Dimension : Nominal length)	1000.0
5.3.2 (Dimension : Nominal Width)	1000.0
5.3.3 (Dimension : Thickness)	1000.0
5.3.5.1 (Shape-Straightness of edges)	1000.0
5.3.5.2 (Shape-Squareness of edges)	1000.0
5.4.2 (Apparent density)	1000.0
5.4.3 (Moisture movement)	3000.0
5.4.4 (Mechanical characteristics-Bending strength(MOR))	4000.0
5.4.4 (Mechanical Characteristics-Modulus of elasticity(MOE))	4000.0
5.4.5 (Water impermeability)	4000.0
5.5.2 (Freeze-thaw)	25000.0
5.5.3 (Heat-rain)	100000.0
5.5.4 (Warm water)	25000.0
5.5.5 (Soak-dry)	25000.0

279

IS 14871:2000 - PRODUCTS IN FIBRE REINFORCED CEMENT —LONG CORRUGATED OR ASYMMETRICAL SECTION SHEETS AND FITTINGS FOR ROOFING AND CLADDING

PRODUCTS IN FIBRE REINFORCED CEMENT —LONG CORRUGATED OR ASYMMETRICAL SECTION SHEETS AND FITTINGS FOR ROOFING AND CLADDING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.5.1.1. & B1 (Distance Between Extreme Complete Corrugation Pitch, a)	500.0
5.5.1.1. & B1 (Measurement of Corrugation Height, h)	500.0
B2 (Dimension-Length)	500.0
B2 (Dimension-width)	500.0
B3 (Dimension-Thickness)	1000.0
B4 (Dimension: Squareness)	500.0
B5 (Dimension: Height of Edges)	500.0
5.5.1.2 (Mechanical characteristics: Breaking Load)	5000.0
5.5.1.2 (Apparent density)	1000.0
5.5.2.b. (Impermeability)	4000.0

280

IS 14862:2000 - Fibre cement flat sheets-Specification

Fibre cement flat sheets-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Dimensional and Geometrical Characteristics)	2000.0
5.2.1 (Mechanical and Physical Characteristics-Bending strength)	4000.0
5.2.2 (Mechanical and Physical Characteristics-Apparent density)	1000.0
6.1 (Type characteristics-Bending strength)	8000.0
6.2 (Type characteristics-Water impermeability)	4000.0
6.3 (Type characteristics-Frost Resistance)	25000.0
6.4 (Type characteristics-Warm water)	25000.0
6.6 (Type characteristics- Heat rain test)	100000.0
6.5 (Type characteristics-soak- dry test)	25000.0

281

IS 16714:2018 - Ground Granulated Blast Furnace Slag for Use in Cement, Mortar and Concrete

Ground Granulated Blast Furnace Slag for Use in Cement, Mortar and Concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 Table 1 (Chemical Requirements of GGBS)	5000.0
5.2 (Moisture content of GGBS)	1000.0
6,Table 2 (Physical requirements)	5000.0

282

IS 4020(Parts 1 to 16):1998 RA 2018 - Door shutters-Methods of Tests

Door shutters-Methods of Tests

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2-2.1 (Dimension: Height(mm) (IS 4020 (part 2) : 1998))	250.0
2-2.2 (Dimension:Width (IS 4020 (part 2) : 1998))	250.0
2-2.3 (Diemension:Thickness (IS 4020 (part 2) : 1998))	250.0
2-2.4 (Squareness (IS 4020 (part 2) : 1998))	250.0
3-2.1 (General Flatness: Twist(IS 4020 (part 3) : 1998))	500.0
3-2.2 (General flatness:Warping (IS 4020 (part 3) : 1998))	250.0
3 -2.2 (General flatness:Cupping (IS 4020 (part 3) : 1998))	250.0
4 (Local Planeness Test: IS 4020 (part 4) : 1998)	1000.0
5 (Impact Indentation Test (IS 4020 (part 5) : 1998))	1000.0
7 (Edge Loading Test ( IS 4020 (part 7) : 1998))	1500.0
8 (Shock resistance Test (IS 4020 (part 8) : 1998))	1500.0
9 (Buckling resistance test (IS 4020 (part 9) : 1998))	1500.0
10 (Slamming Test (IS 4020 (part 10) : 1998))	1000.0
11 (Misuse Test(IS 4020 (part 11) : 1998))	1000.0
13 (End Immersion Test: IS 4020 (part 13) : 1998)	1000.0
14 (Knife Test :IS 4020 (part 14) : 1998)	1000.0
15 (Glue adhesion Test (IS 4020 (part 15) : 1998))	1000.0
16 (Screw Withdrawal resistance test:(IS 4020 (part 16) : 1998))	1000.0
custom (Dimension)	1000.0
custom (Density)	1000.0
custom (Moisture content (% ))	1000.0
custom (Water absorption (%))	1000.0
custom (Thickness swelling (%))	1000.0
6 (Flexure Test-IS 4020 (Part 6):1998)	1000.0

283

ETI/OHE/11(5/89) (2018) - Specification for Steel Tube

Specification for Steel Tube

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
14 (Tensile Strength)	1000.0
14 (Yield Strength)	1000.0
14 (% Elongation)	1000.0
7 (Sulphur)	500.0
7 (Phosphorus)	500.0
12 (Mass of Zinc coating)	2000.0

284

CUS/SR/MECH-41 (2022) - Relish Burni

Relish Burni

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0

285

CUS/SR/MECH-40 (2022) - Relite Container

Relite Container

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0

286

CUS/SR/MECH-39 (2022) - Water Jug

Water Jug

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0

287

CUS/SR/MECH-38 (2022) - Butter Dish

Butter Dish

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0

288

CUS/SR/MECH-37 (2022) - Plain Handi

Plain Handi

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Inside diameter)	1000.0

289

CUS/SR/MECH-36 (2022) - Storage Drum

Storage Drum

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0

290

CUS/SR/MECH-35 (2022) - Serving Plate

Serving Plate

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Dimension)	1000.0

291

CUS/SR/MECH-34 (2022) - Feeding Bottle

Feeding Bottle

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0

292

CUS/SR/MECH-33 (2022) - Smart Steamer

Smart Steamer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1200.0

293

CUS/SR/MECH-32 (2022) - Lunch Box/Lunch Kit

Lunch Box/Lunch Kit

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1200.0
2.0 (Capacity)	800.0

294

CUS/SR/MECH-31 (2022) - Designer Dryfruit Set

Designer Dryfruit Set

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1200.0

295

CUS/SR/MECH-30 (2022) - Tiffin Carrier

Tiffin Carrier

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1200.0
1.0 (Dimension & Visual Examination)	2500.0
2.0 (Chemical Composition, % by mass)	4000.0

296

CUS/SR/MECH-29 (2022) - Milk Boiler

Milk Boiler

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0

297

CUS/SR/MECH-28 (2022) - Oil Dispenser

Oil Dispenser

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0

298

CUS/SR/MECH-27 (2022) - Stainless Steel Kadai

Stainless Steel Kadai

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Inside diameter)	1000.0

299

CUS/SR/MECH-26 (2022) - Stainless Steel Saucepan

Stainless Steel Saucepan

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Inside diameter)	1000.0

300

CUS/SR/MECH-25 (2022) - Luxuria Tea Urn

Luxuria Tea Urn

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Capacity)	1000.0