NTH - Management Information System

National Test House (SR), Chennai

CSIR Road, Tharamani, Chennai - 600113, Chennai, Chennai, Tamil Nadu, 600113

9444380435 director-chn[at]nth[dot]gov[dot]in

Scope List

Reset

597 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

181

IS 14246 (2024) - Continuously Pre-Painted Galvanized Steel Sheets and Strips

Continuously Pre-Painted Galvanized Steel Sheets and Strips

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Total coated thickness (As received condition), mm)	500.0
4.2 (Mass of Zinc Coating)	2000.0
4.3 (Paint Coating Thickness)	2000.0
4 (% Elongation)	1000.0
4 (Yield Stress, MPa)	1000.0
4 (Tensile Strength, MPa)	1000.0
4 (Chemical Analysis (As per IS 513 (Part-1):2016 including Aluminium and Silicon))	3000.0
9 (Base Metal Thickness, mm)	500.0
6.2 (Bend Test)	1000.0
6.3 (Pencil Hardness Test)	1000.0
6.4 (Impact Resistance Test)	1000.0
8.3 (Hardness, HRB (As per Cl. 8.3 of IS 513))	2000.0
6.5 (Cross Hatch Test)	1000.0

182

CUS/SR/MECH-51 (2024) - Gas Trolley

Gas Trolley

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions)	2000.0
2.0 (Weight)	500.0
3.0 (Load Capacity test)	2000.0

183

IS 516 (Part-11) (2020) - Hardened Concrete - Determination of Portland cement Content of Hardened Hydraulic Cement Concrete

Hardened Concrete - Determination of Portland cement Content of Hardened Hydraulic Cement Concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Portland cement content of a sample of hardened hydraulic cement concrete - IS 516 (Part 11) : 2020)	5000.0
Custom (Cement : Sand ratio by weight (considering the submitted mortar sample contains Sand & OPC only))	1000.0

184

IS 2629 (1985 (Reaffirmed 2021)) - Recommended Practice for Hot-Dip Galvanizing of Iron and Steel – Specification

Recommended Practice for Hot-Dip Galvanizing of Iron and Steel – Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Freedom From Defect as per IS 2629)	1250.0
6.3 (Mass of Coating)	2000.0
6.2 (Uniformity in Thickness)	1000.0
6.4.1 (Pivoted Hammer Test for Zinc Coated Fabricated Product)	3000.0
6.4.3 (Bend Test)	1000.0
6.4.1 (Pivoted Hammer Test)	1000.0
6.4.2 (Knife Test)	1000.0
TDS-1 (Coating thickness test (as per IS 6012))	1500.0
6.2 (Uniformity of zinc coating (as per IS 2633))	1000.0
TDS-2 (Dimension, mm)	1000.0
TDS-3 (Tensile Strength (As per IS 1608), N/mm²)	1000.0
TDS-4 (Yield Strength (As per IS 1608), N/mm²)	1000.0
TDS-5 (Percentage Elongation (As per IS 1608), %)	1000.0
TDS-6 (Bend Test (As per IS 1599))	1500.0
6.3 (Mass of zinc coating (as per IS 6745), g/m²)	2000.0

185

CUS/SR/Chem (2024) - Custom Standard for Metal Samples

Custom Standard for Metal Samples

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon)	1000.0
2 (Manganese)	1000.0
3 (Sulphur)	1000.0
4 (Phosphorous)	1000.0
5 (Silicon)	1000.0
6 (Copper (as Cu))	1000.0
7 (Nickel (as Ni))	1000.0
Custom (Chemical composition - IS 9879:1998.)	5000.0
Custom (Chemical Composition for Metal samples)	5000.0

186

CUS/SR/NDT/CUSTOM/001 (2024) - Welding wire

Welding wire

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Size of Wire)	1000.0
2.0 (Type of Wire)	2000.0

187

CUS/SR/NDT/ICF/001 (2024) - Plate Spring

Plate Spring

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Chemical composition % by mass)	4500.0
2.0 (Rockwell hardness, (HRC))	2000.0
3.0 (Depth of Decarburization)	3000.0

188

IS 2095 (Part 1) (2023) - Gypsum Plaster Board, Part 1 - Plain Gypsum Plaster Boards

Gypsum Plaster Board, Part 1 - Plain Gypsum Plaster Boards

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1.1 (Dimensions - Length, mm)	500.0
7.1.1 (Dimensions - Width, mm)	500.0
7.1.1 (Dimensions - Thickness, mm)	500.0
7.1.2.1 (Straightness of Edge,)	500.0
7.1.2.1 (Squareness of Edge, mm)	500.0
7.1.3 (Edge & End Profile, Depth of Taper)	500.0
7.1.3 (Edge & End Profile, Width of Taper)	500.0
7.2 (Density)	1000.0
7.1.3.1 (Edge and End profile)	500.0
7.1.3.1 (Flexural Breaking Load, in Transverse Direction)	2000.0
7.1.3.1 (Flexural Breaking Load, in longitudinal Direction)	2000.0

189

Custom Standard/NTHSR/Chemical & Microbiology - Chemical & Microbiology testing of Miscelleneous Types of Samples

Chemical & Microbiology testing of Miscelleneous Types of Samples

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Bio-chemical oxygen demand (BOD), Method: IS 3025 (Part 44) : 2023 / As per relevant standard)	3000.0
2 (Chemical oxygen demand (COD), Method: IS 3025 (Part 58) : 2023 / As per relevant standard)	2000.0
3 (Total dissolved solids (TDS), Method: IS 3025 (Part 16))	1000.0
4 (pH value, Method: IS 3025 (Part 11))	1000.0
5 (Sulphate (as SO4), Method: IS 3025 (Part 24)/Any relevant standard)	1000.0
6 (Total alkalinity as calcium carbonate, Method: IS 3025 (Part 23)/Any relevant standard)	1000.0
7 (Total hardness (as CaCO3), Method: IS 3025 (Part 21)/Any relevant standard)	1000.0
8 (Calcium (as Ca), mg/l, Method: IS 3025 (Part 40))	1000.0
Custom (pH of Soil sample - IS 2720 (Part 26):1987)	1200.0
Custom (Total viable fungal count per gram of agarbatti material - As per standard method)	2500.0

190

IS 2380(Part I to XXIII) - Methods of Test for Wood Particle boards and boards from other lignocellulosic materials

Methods of Test for Wood Particle boards and boards from other lignocellulosic materials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Accuracy of dimensions of boards:(IS 2380 -Part II))	3000.0

191

IS 3097 (2006) - Veneered Particle Boards -Specification

Veneered Particle Boards -Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.1 h (Determination of deflection under sustained load-IS 2380 (Part 13):1977)	1500.0
9.1 g (Modulus of Rupture and Modulus of Elasticity-IS 2380 (Part 4):1977)	2500.0
9.1 f (Adhesion of Plies-IS 3097:2006)	500.0
9.1 e (Swelling in Water-IS 2380 (Part 17):1977)	2000.0
9.1 d (Water Resistance Test--IS 3097:2006)	1000.0
9.1 c (Water Absorption-IS 2380 (Part 16):1977)	1000.0
9.1 b (Moisture Content-IS 2380 (Part 3):1977)	1000.0
9.1 a (Density-IS 2380 (Part 3):1977)	500.0
7 (Dimensions and Tolerances-IS 3097:2006, Annex C)	500.0
6.3 (Finish-IS 3097:2006)	500.0

192

IS 12823 (2015) - Wood Products - Prelaminated Particle Boards -Specification

Wood Products - Prelaminated Particle Boards -Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.14 (Resistance to Stain-IS 12823:2015 Annex G)	1500.0
10.13 (Resistance to Cigarette Burn-IS 12823:2015 Annex F)	500.0
10.12 (Resistance to Crack-IS 12823:2015 Annex E)	500.0
10.11 (Resistance to Steam-IS 12823:2015 Annex D)	500.0
10.9, Table 2, Sl No (viii) (Screw Withdrawal Strength -IS 2380 (Part 14):1977)	1500.0
10.8, Table 2, Sl No (vii) (Tensile strength perpendicular to surface after ageing-IS 12823:2015 &-IS 2380 (Part 5):1977)	2000.0
10.7 Table 2, Sl No (vi) (Tensile strength perpendicular to surface-IS 2380 (Part 5):1977)	2000.0
10.6Table 2, Sl No (v) (Modulus of Rupture & Modulus of Elasticity-IS 2380 (Part 4):1977)	2500.0
10.5 Table 2, Sl No (iv) (Swelling in Water-IS 2380 (Part 17):1977)	1000.0
10.4 Table 2, Sl No (iii) (Water Absorption-IS 2380 (Part 16):1977)	1000.0
10.3 (Moisture Content-IS 2380 (Part 3):1977)	1000.0
10.2, Table 2, Sl No (i) & (ii) (Density-IS 2380 (Part 3):1977)	500.0
8 (Dimension & Tolerances-IS 12823:2015 Annex B)	500.0
7 (Finish-IS 12823:2015)	1000.0
- (Nail Withdrawal strength (IS 2380-XIV):)	1500.0
- (Falling hammer Impact test:(IS 2380-X):)	2000.0
- (Compression Parallel to surface:(IS 2380-VIII))	2000.0
- (Compression Perpendicular to plane of the board:(IS 2380-Part VII))	2000.0

193

Water based Emulsion (2023) - Custom standard for Water based Emulsion

Custom standard for Water based Emulsion

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volatile organic compounds)	2000.0

194

IS 4250 (1980) - Specification for domestic electric food - Mixers (Liquidizers And Grinders) (First Revision)

Specification for domestic electric food - Mixers (Liquidizers And Grinders) (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
38.1 (Type tests)	20000.0
38.2 (Acceptance tests)	15000.0

195

IS 1060(Part 1):1966 - Paper

Paper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

196

IS 1060 - METHODS OF SAMPLING AND TEST FOR PAPER AND ALLIED PRODUCTS

METHODS OF SAMPLING AND TEST FOR PAPER AND ALLIED PRODUCTS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

197

CUS/SR/MECH-50 (2024) - Perforated Metal Sheet

Perforated Metal Sheet

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimension, mm)	2000.0
2.0 (Percentage of perforated area, %)	2000.0
3.0 (Mass of Zinc coating)	2000.0
4.0 (Powder Coating Thickness, micron)	2000.0

198

CUS/SR/CH/CPWD-Chennai - Custom standard for Sulphates in Ground Water and Soil

Custom standard for Sulphates in Ground Water and Soil

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test results (Borehole 1))	13000.0
2 (Test results (Borehole 2))	13000.0

199

IS 1130 (Marble) (1969) - Marble

Marble

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

200

IS 1130 (1969) - Marble (blocks, Slabs And Tiles)

Marble (blocks, Slabs And Tiles)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

201

IS 208 (2020) - Door Handles - Specification ( Sixth Revision )

Door Handles - Specification ( Sixth Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Dimensions)	2000.0
7 (Anodizing)	2000.0
8.1 (Pencil Hardness Test)	1000.0
8.2 (Corrosion Test)	2000.0
8.3 (Quenching Test)	2000.0

202

IS 204 (1992) - Tower Bolts

Tower Bolts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Dimensions)	2000.0
7 (Anodizing)	2000.0

203

IS 2681 (1993) - Non-ferrous metal sliding door bolts (Aldrops) for use with padlocks

Non-ferrous metal sliding door bolts (Aldrops) for use with padlocks

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Dimensions)	2000.0
8.2 (Anodizing)	2000.0

204

IS 205 (1992) - Non Ferrous Metal Butt Hinges

Non Ferrous Metal Butt Hinges

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Dimensions)	2000.0
6.3 (Dimension measurement & Visual Observation)	2000.0
7.2 (Anodizing)	2000.0

205

IS 1708(Parts 1-18)1986: RA 2020 - METHODS OF TESTING OF SMALL CLEAR SPECIMENS OF TIMBER

METHODS OF TESTING OF SMALL CLEAR SPECIMENS OF TIMBER

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Moisture content (IS 1708(1):1986))	1000.0
2 (Specific gravity (IS 1708(2):1986))	500.0
3 (Volumetric Shrinkage (IS 1708(3)1986))	1000.0
5 (Static bending strength (IS 1708(5):1986) 1.Fibre stress at limit of proportionality(FS at LP) 2.Equivalent fibre stress at maximum load(MOR) 3.Modulus of Elasticity( M of E) 4.Horizontal shear(HS)stress on neutral plan at LP 5.Horizontal shear stress at maximum load(ML) 6.Wk to LP 7.Wk to ML)	3000.0
15 (Screw holding power(IS 1708(15):1986))	1500.0
8 (Compressive strength-Parallel to grain(IS 1708(8)1986))	1500.0
9 (Compressive strength-Perpendicular to grain(IS 1708(9):1986))	1500.0
12 (Tensile strength -Parallel to grain(IS 1708(12):1986))	2000.0
15 (Nail holding Power (IS 1708(15):1986))	1500.0
5 (Static bending strength-Equivalent fibre stress at maximum load ( modulus of rupture - M of R ) & Modulus of elasticity ( M of E ))	2000.0
custom (Dimension)	1000.0
custom (Shear strength Parallel to Grain (IS 1708 ( Part 12 ) • 1986))	1500.0

206

CUS/SR/MECH-49 (2024) - FRP Coated SS Plate

FRP Coated SS Plate

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Peel off test)	2500.0
2.0 (Shrinkage test)	2500.0

207

TI/SPC/OHE/CW/0971 - Hard drawn grooved copper(HDGC) contact Wire for Electrical Traction (Drawn out of continuous Cast copper wire Rod) .

Hard drawn grooved copper(HDGC) contact Wire for Electrical Traction (Drawn out of continuous Cast copper wire Rod) .

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.1.1 (Visual Examination)	1000.0
9.1.2 (Dimension)	2000.0
9.1.3 (Weight)	1500.0
9.1.4 (Resistance/km at 20 Deg. C)	3000.0
9.1.5 (Brinell Hardness)	2000.0
9.1.6 (Tensile Strength)	2000.0
9.1.7 (Elongation at Gauge Length 200 mm)	1000.0
9.1.8 (Bending Test)	1000.0
9.1.9 ((Cu+Ag))	2000.0
9.1.10 (Micro structure Examination)	3000.0

208

RDSO/TI/SPC/OHE/CAT(Cd-Cu)/0971 - Technical specification for Cadmium Copper for Overhead Electrical Traction-Cu-Cd

Technical specification for Cadmium Copper for Overhead Electrical Traction-Cu-Cd

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1.1 (Chemical composition, percent by mass (Cu+Ag))	5000.0
8.2.1 (Visual examination)	1000.0
8.2.3 (Measurement of diameter of individual wires and stranded conductors, mm)	2000.0
8.2.4 (Measurement of weight of wire and conductor, kg/km)	1000.0
8.2.5 (Measurement of Lay length and lay ratio of each layer of stranded conductor)	3000.0
8.2.6 (Measurement of Electrical resistance of wire and stranded conductor)	5000.0
8.2.7 (Tensile test on wires -3 wires)	3000.0
8.2.7 (Tensile test on wires -7 wires)	3500.0
8.2.7 (Tensile test on wires -19 wires)	9500.0
8.2.7 (Tensile test on wires -37 wires)	18500.0
8.2.8 (Wrapping test on wires)	1000.0

209

IEC 62271-102:2018 (2018) - High-voltage switch gear and control gear - Part 102: Alternating current disconnectors and earthing switches.

High-voltage switch gear and control gear - Part 102: Alternating current disconnectors and earthing switches.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.106 (Mechanical Endurance Test M0 Class on DBCR Isolator (1000 Operation))	20000.0
7.5 (Temperature Rise Test as per IEC62271-102:2018)	20000.0
Cl.no 7.2.7.3 of IS/IEC 62271-102 (Lightning Impulse Voltage Dry Test)	50000.0
Cl.no 7.2.7.2 of IS/IEC 62271-102 (Power Frequency Voltage Dry Test)	2500.0
Cl.no 7.2.7.2 of IS/IEC 62271-102 (Power Frequency Voltage Wet Test)	2500.0

210

CUS/SR/MECH-48 - Bi-Cycle - Girls

Bi-Cycle - Girls

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions and visual examination)	20000.0
2.0 (Chemical composition, % by mass)	5000.0

First
Prev
6
7
8
9
Next
Last