| 151 |
IS 12701 (1996) - Rotational moulded polyethylene water storage tanks - specification (First Revision) |
Rotational moulded polyethylene water storage tanks - specification (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3,4,5,6&7 (Water Storage Tank Test Results) |
14000.0 |
|
| 7.6 (Overall Migration) |
3000.0 |
|
| 9.1 (Carbon Black content) |
2000.0 |
|
| 9.1 (Carbon Black Dispersion) |
1000.0 |
|
| 4.2.3.a (Carbon Black Content) |
2000.0 |
|
| 4.2.3.b (Carbon Black Dispersion) |
2000.0 |
|
|
| 152 |
CUSTOM/SCRIM REINFORCED POLYETHYLENE WITH MANO FILAMENT/2025 - SCRIM REINFORCED POLYETHYLENE WITH MANO FILAMENT |
SCRIM REINFORCED POLYETHYLENE WITH MANO FILAMENT |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Mass per unit area) |
1000.0 |
|
| 2.0 (Tensile Force (MD)) |
1000.0 |
|
| 3.0 (Tensile Force (CD)) |
1000.0 |
|
|
| 153 |
IS 17190:2020 - GROUTS FOR FILLING OF JOINTS OF TILES AND STONES |
GROUTS FOR FILLING OF JOINTS OF TILES AND STONES |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Clause 4,Table 1 (Linear shrinkage) |
2000.0 |
|
| Clause 4,Table 1 (Water absorption) |
1000.0 |
|
| Clause 4,Table 1 (Compressive strength) |
4000.0 |
|
| Clause 4,Table 1 (Flexural strength) |
4000.0 |
|
| Clause 4,Table 1 (Abrasion resistance) |
5000.0 |
|
| Clause 4,Table 1 (Transverse deformation) |
2000.0 |
|
| custom (GROUTS FOR FILLING OF JOINTS OF TILES AND STONES-(CEMENTITIOUS & RESIN GROUTS)) |
18000.0 |
|
| custom (Custom-Chemical resistance properties) |
2500.0 |
|
|
| 154 |
IS 458:2021 - PRECAST CONCRETE PIPES(WITH AND WITHOUT REINFORCEMENT) |
PRECAST CONCRETE PIPES(WITH AND WITHOUT REINFORCEMENT) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8.1 & 8.2 (Dimensions & Tolerances) |
1000.0 |
|
| 9 (Workmanship and Finish) |
1000.0 |
|
| 10.2(b) (Three-edge bearing test) |
5000.0 |
|
| 10.2(c) (Permeability test) |
3000.0 |
|
|
| 155 |
14276 (2016) - Cement Bonded Particle Boards —
Specification |
Cement Bonded Particle Boards —
Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6 (Finish) |
500.0 |
|
| 7 (Dimensions and Tolerances) |
1000.0 |
|
| 10.3 (Density) |
1000.0 |
|
| 10.4 (Moisture Content) |
1000.0 |
|
| 10.5 (Water Absorption) |
1000.0 |
|
| 10.6 (Swelling in water) |
1000.0 |
|
| 10.7 (Modulus of Rupture (MOR)) |
1500.0 |
|
| 10.8 (Modulus of Elasticity (MOE)) |
1500.0 |
|
| 10.9 (Tensile Strength perpendicular surface) |
1500.0 |
|
| 10.10 (Screw withdrawal strength) |
1000.0 |
|
| 8.5 (Workability) |
500.0 |
|
| custom (Surface alkalinity, pH) |
1200.0 |
|
| custom (Compressive strength (Perpendicular to surface)) |
2000.0 |
|
| Table 1 (Clauses 8.2, 8.3, 8.4,10.1 and 10.3 to 10.10) (Requirements of Physical & Mechanical Properties for Cement Bonded Particle Boards) |
11000.0 |
|
|
| 156 |
GFRC - on the lines of ASTM C947-03 - Glass Fiber Reinforced Concrete |
Glass Fiber Reinforced Concrete |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| custom (Dry Density, Water absorption, Bending strength-LOP/MOE & MOR) |
10000.0 |
|
|
| 157 |
IS 2633 (1986) - Uniformity of Coating on Zinc Coated Articles |
Uniformity of Coating on Zinc Coated Articles |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Uniformity of Coating - IS 2633) |
1000.0 |
|
|
| 158 |
IS 2046 (1995) - Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets |
Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5.1 (Colour and pattern) |
500.0 |
|
| 5.2.1 (Surface Finish) |
500.0 |
|
| 5.3 (Thickness) |
1000.0 |
|
| 5.4.1 (Surface Defects) |
1000.0 |
|
| 5.4.2 (Edge Defects) |
1000.0 |
|
| 5.4.3 (Broken Corners) |
1000.0 |
|
| 5.4.4 (Sanding Defects) |
1000.0 |
|
| 5.4.5 (Warping (Flatness)) |
1000.0 |
|
| 5.4.6 (Length and Width) |
1000.0 |
|
| 5.4.7 (Straightness of Edges) |
1000.0 |
|
| 5.4.8 (Squareness of laminates) |
1000.0 |
|
| 5.5 (Resistance to suface wear) |
3000.0 |
|
| 5.5 (Resistance to immersion in Boiling water(mass increase)) |
1000.0 |
|
| 5.5 (Resistance to immersion in Boiling water(thickness increase)) |
1000.0 |
|
| 5.5 (Resistance to immersion in boiling water (Appearance)) |
500.0 |
|
| 5.5.3 (Resistance to Dry Heat at 180 degC.) |
2000.0 |
|
| 5.5 (Dimensional Stability at Elevated Temperature (L)) |
1500.0 |
|
| 5.5 (Dimensional Stability at Elevated Temperature(T)) |
1500.0 |
|
| 5.5 (Dimensional Stability at 20 degC(L)) |
1000.0 |
|
| 5.5 (Dimentional Stability at 20 degC(T)) |
1000.0 |
|
| 5.5 (Resistance to Cracking) |
2000.0 |
|
| 5.5 (Resistance to Scratching) |
2000.0 |
|
| 5.5 (Resistance to Staining) |
5000.0 |
|
| 5.5 (Resistance to colour change in Xenon arc light) |
3000.0 |
|
| 5.5 (Resistance to Cigarate Burns) |
2000.0 |
|
| 5.5 (Resistance to Steam) |
2000.0 |
|
| 5.5 (Tensile strength) |
2000.0 |
|
| 5.5 (Flexural Strength) |
2000.0 |
|
| 5.5 (Resistance to crazing) |
1500.0 |
|
| 5.5 (Resistance to surface wear) |
5000.0 |
|
| 5.5 (Resistance to Impact by small diameter ball) |
2000.0 |
|
| 5.5 (Flexural Modulus) |
2000.0 |
|
|
| 159 |
IS 7809 : Part 3 : Sec 1, IS 7809 : Part 2 & IS 7809 : Part 1 (1986) - Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 3 requirements or individual materials: Sec 1 plasticized polyvinylchloride tapes with non - Thermosetting adhesive (First Revision) & Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 1 General requirements & Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 2 Test Methods. |
Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 3 requirements or individual materials: Sec 1 plasticized polyvinylchloride tapes with non - Thermosetting adhesive (First Revision) & Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 1 General requirements & Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 2 Test Methods. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.2 (Width) |
500.0 |
|
| 3.3 (Length) |
500.0 |
|
| 3.4 (Thickness) |
1000.0 |
|
| 4.1 (Tensile Strength) |
1500.0 |
|
| 4.0 (Appearance) |
500.0 |
|
| 5.0 (Freedom from Defects) |
500.0 |
|
| 6.1 (Core Diameter) |
1000.0 |
|
| 9.0 (Elongation) |
500.0 |
|
|
| 160 |
IS 2690(1):2023 - IS 2690(1):2023 INDIAN STANDARD SPECIFICATION FOR "BURNT CLAY FLAT TERRACING TILES-MACHINE MADE" |
IS 2690(1):2023 INDIAN STANDARD SPECIFICATION FOR "BURNT CLAY FLAT TERRACING TILES-MACHINE MADE" |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4 (General Quality) |
250.0 |
|
| 5.1.1 (Dimension-Length) |
250.0 |
|
| 5.1.2 (Dimension-Width) |
250.0 |
|
| 5.1.3 (Dimension-Thickness) |
250.0 |
|
| 5.2.1 (Warpage) |
250.0 |
|
| 6 (Water Absorption-Average value) |
500.0 |
|
| 6 (Water Absorption-Max Individual value) |
500.0 |
|
| 7 (Flexural Strength-Modulus of Rupture(Average value)) |
1000.0 |
|
| 7 (Flexural Strength-Modulus of Rupture(Minimum Individual Value)) |
1000.0 |
|
| 9 (Marking) |
250.0 |
|
|
| 161 |
IS 8041 (1990) - Rapid hardening portland cement - Specific4tion (Second Revision) |
Rapid hardening portland cement - Specific4tion (Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.1 (Fineness) |
1000.0 |
|
| 6.2 (Soundness-Lechatlier method) |
500.0 |
|
| 6.3 (Setting time Initial) |
250.0 |
|
| 6.3 (Setting time,Final) |
250.0 |
|
| 6.4 (Compressive strength-(24 hours ±30 minutes)) |
2000.0 |
|
| 6.4 (Compressive strength-(72 hours ±1hour)) |
2000.0 |
|
| 5.1,Table 1 (Chemical requirements:) |
4000.0 |
|
|
| 162 |
IS 12436:1988 - Specification for Preformed Rigid Polyurethane (PUR) and Polyisocyanurate(PIR) foams for thermal insulation |
Specification for Preformed Rigid Polyurethane (PUR) and Polyisocyanurate(PIR) foams for thermal insulation |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| A-2 (Density(as per IS 7888:1976):) |
1000.0 |
|
|
| 163 |
IS 1719 (2000) - Industrial Textiles - Pressed Wool Felts |
Industrial Textiles - Pressed Wool Felts |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.2 & 6.2.1 (pH value of aqueous extract - Method IS 1390) |
1200.0 |
|
| 6.2 & 6.2.1 (Water soluble matter - Test method: IS 3456) |
1500.0 |
|
| 6.2 & 6.2.1 (Ash content - Test method: IS 199) |
1200.0 |
|
|
| 164 |
RDSO Specification .No. WD-01-HLS-94 (Rev.4) (2022) - Specification for Hot Coiled / Cold Coiled Helical Springs |
Specification for Hot Coiled / Cold Coiled Helical Springs |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Brinell Hardness, HBW) |
2000.0 |
|
| 2.0 (Chemical composition, % by mass) |
5000.0 |
|
|
| 165 |
on the lines of IS 1734 / ASTM D-2240 /IS 13630 - PVC BOARD / WPC DOOR SHUTTER/FRAME |
PVC BOARD / WPC DOOR SHUTTER/FRAME |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| custom (Density) |
1000.0 |
|
| custom (Hardness (Shore)-ASTM D 2240) |
1000.0 |
|
| custom (Tensile strength (IS 1734(9):1983)) |
2500.0 |
|
| custom (Screw holding Power-on face & End surface {IS 1734(19)}) |
1500.0 |
|
| custom (Lead content extracted from surface: {On the lines of IS 13630(16)}) |
2000.0 |
|
| custom (Compressive strength (IS 1734(10):1983)) |
1500.0 |
|
|
| 166 |
IS 4956 (2020) - Synthetic Detergents for Industrial Purposes — Specification |
Synthetic Detergents for Industrial Purposes — Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (TEST RESULTS (Test method: As referred in IS 4956)) |
6000.0 |
|
|
| 167 |
IS 2888 (2004) - TOILET SOAP - Specification |
TOILET SOAP - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (TEST RESULTS (Test method: As mentioned in IS 2888)) |
5000.0 |
|
|
| 168 |
IS 1838(Part 1):1983 - Preformed fillers for expansion joint in Concrete Pavement and Structures(Non extruding and resilient type) ;Part 1-Bitumen Impregnated Fibre -Specification |
Preformed fillers for expansion joint in Concrete Pavement and Structures(Non extruding and resilient type) ;Part 1-Bitumen Impregnated Fibre -Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4 (Dimension (mm)- Length, Width & Thickness) |
500.0 |
|
| 5.1(i) (Resistance to handling) |
500.0 |
|
| 5.1(ii) (Recovery) |
1000.0 |
|
| 5.1(iii)b (Loss in bitumen) |
3000.0 |
|
| 5.1(iv) (Extrusion) |
1000.0 |
|
| 5.1(v) (Water absorption) |
1000.0 |
|
| 5.1(vi) (Density) |
500.0 |
|
| 5.1(vii) (Bitumen Content) |
2500.0 |
|
| 5.1(viii)a (Weathering) |
1500.0 |
|
| 5.1(viii)b.1 (Recovery test after weathering:) |
500.0 |
|
| 5.1(viii)b.2 (Compression Test after weathering:) |
500.0 |
|
| 5.1(viii)b.3 (Extrusion after weathering) |
1500.0 |
|
| 5.1(ix) (Penetration of the recovered Bitumen:) |
3000.0 |
|
|
| 169 |
IS 516(Part 4):2018 - Hardened Concrete Methods of Test-Sampling ,Preparing and Testing of Concrete Cores |
Hardened Concrete Methods of Test-Sampling ,Preparing and Testing of Concrete Cores |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8 (Compression Test-Equivalent cube strength N/sqmm) |
10000.0 |
|
|
| 170 |
IS 1838 : Part 1 (1983) - preformed fillers for expansion joint in concrete pavement and structures (non extruding and resilient type): Part 1 Bitumen impregnated fibre - Specification |
preformed fillers for expansion joint in concrete pavement and structures (non extruding and resilient type): Part 1 Bitumen impregnated fibre - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4 (Dimensions) |
500.0 |
|
| 4.1(b) (Width) |
1000.0 |
|
| 4.1(c) (Thickness) |
1000.0 |
|
| 5.1(i) (Resistance to handling) |
1000.0 |
|
| 5.1(ii) (Recovery) |
1000.0 |
|
| 5.1(iii)a (Compression) |
1000.0 |
|
| 5.1(iv) (Extrusion) |
1000.0 |
|
| 5.1(v) (Water Absorption) |
1000.0 |
|
| 5.1(vi) (Density) |
1000.0 |
|
| 5.1(vii) (Bitumen Content) |
2000.0 |
|
| 5.1(Viii)a (Weathering) |
5000.0 |
|
| 5.1(viii)b.1 (Recovery Test After Weathering) |
1000.0 |
|
| 5.1(viii)b.2 (Compression Test after Weathering) |
1000.0 |
|
| 5.1(viii)b.3 (Extrusion after weathering) |
1000.0 |
|
| 5.1(iii)b (Loss in Bitumen) |
1000.0 |
|
|
| 171 |
IS 7884 (2023) - Shampoo - Specification |
Shampoo - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.4 (Test Report in Annexure) |
6000.0 |
|
|
| 172 |
ASME Code IX Boiler and Pressure Vessel Code - QW 382 (2021) - QW 382 - Hard Facing Weld metal overlay (Wear Resistance) |
QW 382 - Hard Facing Weld metal overlay (Wear Resistance) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Macro Examination) |
1000.0 |
|
| 2.0 (Liquid Penetrant Test) |
1000.0 |
|
| 3.0 (Hardness) |
2000.0 |
|
| 4.0 (Chemical Composition, % by mass) |
8000.0 |
|
|
| 173 |
28954-TNTB (2025) - Wooden Colour Pencil -TNTB |
Wooden Colour Pencil -TNTB |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Results of the Tests-Wooden Colour Pencil (Attached Annexure)) |
1755.0 |
|
|
| 174 |
Textile NABL-2023-26 - Textile NABL-2023-26 |
Textile NABL-2023-26 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Footwear Flexing Endurance Test) |
2000.0 |
|
|
| 175 |
Paper NABL-2023-26 - Paper NABL-2023-26 |
Paper NABL-2023-26 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Apparent Bulk Density) |
1000.0 |
|
| 2 (Ash content at 525deg.C) |
2000.0 |
|
| 3 (Ash content at 900deg.C) |
2000.0 |
|
| 4 (Water Absorptiveness-Cobb test) |
2000.0 |
|
| 5 (Mass of Coating for Carbon paper) |
1000.0 |
|
| 6 (Moisture Content) |
1000.0 |
|
| 7 (Smoothness Test) |
2000.0 |
|
| 8 (Substance of base paper) |
1000.0 |
|
| 9 (Substance (Grammage)) |
1000.0 |
|
| 10 (Tearing Resistance) |
2000.0 |
|
| 11 (Tensile Index) |
2000.0 |
|
| 12 (Thickness) |
1000.0 |
|
| 13 (Stiffness Test) |
2000.0 |
|
|
| 176 |
Plastics NABL-2023-26 - Plastics NABL-2023-26 |
Plastics NABL-2023-26 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Density) |
1000.0 |
|
| 2 (Elongation) |
1000.0 |
|
| 3 (Tensile Strength) |
2000.0 |
|
|
| 177 |
Rubber NABL-2023-26 - Rubber NABL-2023-26 |
Rubber NABL-2023-26 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Density / Sp. Gravity) |
1000.0 |
|
| 2 (Elongation at Break) |
1000.0 |
|
| 3 (Tensile Strength) |
2000.0 |
|
|
| 178 |
CUSTOM/SR/CHEMICAL (2024) - Custom Standard for Water Samples collected during Social Activity : Mobile Water Testing |
Custom Standard for Water Samples collected during Social Activity : Mobile Water Testing |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Test results for Chemical analysis in Annexure (NON-NABL)) |
- |
|
| Micro-1 (E. coli or thermotolerant coliform bacteria) |
- |
|
| Micro-2 (Total coliform bacteria) |
- |
|
|
| 179 |
303 (2024) - Plywood for General Purpose |
Plywood for General Purpose |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8.1 (Length, in mm) |
400.0 |
|
| 8.1 (Width, in mm) |
400.0 |
|
| 8.2 (Thickness, in mm) |
400.0 |
|
| 8.3 (Squareness, in mm/m) |
400.0 |
|
| 8.3 (Edge Straightness, in mm/m) |
400.0 |
|
| 5 (Classification by Appearance) |
1500.0 |
|
| 9 (Workmanship and finish,) |
2000.0 |
|
| 11.3.1 (a) (Glue Adhesion - Water Resistance Test) |
2000.0 |
|
| 11.3.1 (b) (Glue Adhesion Test - Water Resistance Test - BWR Grade) |
2000.0 |
|
| 11.3.1 cb) (Glue Adhesion Test - Water Resistance Test - BWP Grade) |
2000.0 |
|
| 11.3.2 (Mycological Test) |
1500.0 |
|
| 11.4 (Moisture Content, in %) |
1000.0 |
|
| 11.5 (Static Bending Strength (Modulus of Rupture -Along), in N/mm^2) |
750.0 |
|
| 11.5 (Static Bending Strength (Modulus of Rupture - Across), in N/mm^2) |
750.0 |
|
| 11.5 (Static Bending Strength (Modulus of Elasticity-Along), in N/mm^2) |
750.0 |
|
| 11.5 (Static Bending Strength (Modulus of Elasticity- Across), in N/mm^2) |
750.0 |
|
| 11.6 (Formaldehyde Content Test, in mg/100g) |
3000.0 |
|
| custom (Tensile strength (1734 (Part 9) - 1983)) |
2500.0 |
|
|
| 180 |
CUS/SR/MECH-56 (2025) - Thread Locker |
Thread Locker |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Proof Load, kN) |
3000.0 |
|
| 2.0 (Hardness, HRC) |
2000.0 |
|
|
