NTH - Management Information System

National Test House (SR), Chennai

CSIR Road, Tharamani, Chennai - 600113, Chennai, Chennai, Tamil Nadu, 600113

9444380435 director-chn[at]nth[dot]gov[dot]in

Scope List

Reset

619 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

331

IS 17545:2021 - WHITE CEMENT BASED POLYMERIC PUTTY

WHITE CEMENT BASED POLYMERIC PUTTY

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Form and Condition)	500.0
4.3 (Consistency)	500.0
4.4 (Lead Restriction-ASTM D3335-85a.)	1000.0
4.5, Table 1, (ii) (Water retentivity-Annex C)	1000.0
4.5, Table 1, (iii) (Initial Setting time-Annex D)	250.0
4.5, Table 1, (iv) (Polymer content(based on loss on ignition)-Annex E)	1000.0
4.5, Table 1, (vi) (Cement content-Annex B of IS 5410)	1000.0
4.6 Table 2 (28 days Compressive strength-IS 4031(6))	1000.0
4.5, Table 1, (iii) (Final Setting time-Annex D)	250.0
custom (Potlife)	1000.0
custom (Bulk density)	1000.0
4.5 Table 1,V (Degree of whiteness)	1500.0
custom (Fineness)	1000.0
custom (Water absorption)	1000.0
4.5 Table, 1, (i) (Average Tensile adhesion strength@ 14days-Annex B)	2000.0

332

IS 2250:1981 - Code of Practice for Preparation and use of Masonry Mortars

Code of Practice for Preparation and use of Masonry Mortars

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.4,6.1, Table 1 & Appendix A (Compressive strength of Masonry Mortar)	4000.0
9.1.1 Table 1,Appendix B (Consistency of Masonry Mortar)	500.0
6,Table 1 (Grade of Mortar-Mortar mix ratio (IS 1199))	5000.0
Custom ( ref 5.1.4) (Sulphate content)	1200.0
Custom (Chloride content)	1200.0
custom (Bulk density-kg/cum:{on the lines of IS 2386(III)})	500.0
custom (Pot life (on the lines of IS 5410))	1000.0
custom (Tensile strength (on the lines of IS 15477))	4000.0

333

GOST 2678-94 (1994) - SBS Water Proofing Membrane(Bituminous)

SBS Water Proofing Membrane(Bituminous)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Minimum Elongation at Rupture - One direction (Longitudinal))	1000.0
2 (Minimum Elongation at Rupture - Another direction (Transverse))	1000.0
3 (Water Tightness under pressure 0.2MPa during 24hours)	2000.0

334

IS 2556 ( Part 6 ) : 2021 - VITREOUS SANITARY APPLIANCES ( VITREOUS CHINA)-SPECIFIC REQUIREMENTS OF URINALS AND PARTITION PLATES

VITREOUS SANITARY APPLIANCES ( VITREOUS CHINA)-SPECIFIC REQUIREMENTS OF URINALS AND PARTITION PLATES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (General requirements)	6000.0
5 (Patterns & Sizes)	500.0
6 (Dimensions & Tolerance)	2000.0
7 (Construction)	500.0
8 (Finish)	500.0
9.1 (Cleanability test)	2000.0
9.2 (Splash Test)	1000.0
9.3 (Distortion & Leakage test for wall hung urinal)	1000.0
9.4 (Discharge Test)	1000.0

335

IS 2556 ( Part 3):2024 (2024) - Vitreous Sanitary Appliances (Vitreous China) - - Part 3: Specific Requirements of Squatting Pans

Vitreous Sanitary Appliances (Vitreous China) - - Part 3: Specific Requirements of Squatting Pans

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (General Requirements)	6000.0
4 (Patterns & Sizes)	500.0
5 (Construction)	1000.0
6 (Dimension & Tolerances)	2000.0
6.2 (The Top surface)	500.0
7 (Finish)	500.0
8.2 (Toilet Paper Test)	600.0
8.3 (Smudge Test)	600.0
8.4 (Water holding capacity test)	1000.0
8.5 (Saw dust test)	600.0
8.6 (Splash test)	600.0

336

IS 2556 : Part 4 - VITREOUS SANITARY APPLIANCES (VITREOUS CHINA) — SPECIFICATION PART 4 SPECIFIC REQUIREMENTS OF WASH BASINS

VITREOUS SANITARY APPLIANCES (VITREOUS CHINA) — SPECIFICATION PART 4 SPECIFIC REQUIREMENTS OF WASH BASINS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (General requirements)	6000.0
5 (Dimensions and Tolerances)	2000.0
6.5 (Overflow Test)	1000.0
6.7 (Load Bearing Test)	1000.0
6 & 7 (Construction & Finish)	4000.0

337

IS 2556 (Part 2):2024 - VITREOUS SANITARY APPLIANCES (VITREOUS CHINA) — SPECIFICATION PART 2 SPECIFIC REQUIREMENTS OF WASHDOWN WATER CLOSETS

VITREOUS SANITARY APPLIANCES (VITREOUS CHINA) — SPECIFICATION PART 2 SPECIFIC REQUIREMENTS OF WASHDOWN WATER CLOSETS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Toilet Paper Test)	600.0
8.5 (Load Bearing Test)	1000.0
8.7 (Splashing test)	600.0
5,Table 1 & 2 (Dimensions and Tolerances)	2000.0
6 & 7 (Construction & Finish)	1000.0
8.2 (Smudge Test)	600.0
8.3 (Holding Capacity Test)	1000.0
8.4.1 (Ball Test -Single ball test)	600.0
8.4.2 (Ball Test - Fifty ball Test)	600.0
8.6 (Saw dust Test)	600.0
4 (Pattern)	500.0
3 (General requirements -IS 2556(1))	6000.0

338

CUS/SR/MECH-24 - Bagop Cloth Clip

Bagop Cloth Clip

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions)	1000.0
2.0 (Weight)	500.0
3.0 (Chemical composition, % by mass)	3000.0

339

CUS/SR/MECH-23 - Stainless Steel Gravy Pot (Mini)

Stainless Steel Gravy Pot (Mini)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions)	2000.0
2.0 (Weight)	500.0
3.0 (Capacity)	1000.0
4.0 (Chemical composition, % by mass)	3000.0

340

CUS/SR/MECH-22 - Stainless Steel Insu-Roti Saver (Mini)

Stainless Steel Insu-Roti Saver (Mini)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions)	2000.0
2.0 (Weight)	500.0
3.0 (Capacity)	1000.0
4.0 (Chemical composition, % by mass)	3000.0

341

CUS/SR/MECH-21 - Heavy Duty Hanger

Heavy Duty Hanger

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions)	1000.0
2.0 (Weight)	500.0
3.0 (Design)	500.0

342

IS 14756 (2022) - Stainless Steel Utensils

Stainless Steel Utensils

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Thickness)	1000.0
3 (Chemical composition of Body, % by mass)	3000.0
3.4 (Chemical composition of Lid, % by mass)	3000.0
5 (Workmanship and Finish)	1000.0
6.1 (Staining test, visual observation)	2000.0
6.2 (Mechanical Shock Test)	2000.0
TDS-1 (Capacity)	1000.0
TDS-2 (Weight)	500.0

343

IS 109 (2017) - READY MIXED PAINT, FINISHING, PRIMING, PLASTER, TO INDIAN STANDARD COLOUR NO. 361 LIGHT STONE AND NO. 631 LIGHT GREY, WHITE AND OFF-WHITE

READY MIXED PAINT, FINISHING, PRIMING, PLASTER, TO INDIAN STANDARD COLOUR NO. 361 LIGHT STONE AND NO. 631 LIGHT GREY, WHITE AND OFF-WHITE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Lead Restriction)	-
4.3 (i) a (Drying time Surface dry)	1200.0
4.3 (i) b (Drying Time -Hard Dry)	1200.0
4.3 (ii) (Finish)	100.0
4.3 (iii) (Consistency)	1200.0
4.3 (iv) (Mass, in kg/10 litre)	100.0
4.3 (V) (Colour)	100.0
4.3 (vi) (Wet opacity)	100.0
4.3 vii (Flash point)	400.0
4.3 (viii) (Water content)	100.0
4.3 (ix) (Resistance to alkali)	1500.0
4.3 (x) (Resistance to water)	100.0
4.3 (xi) (Keeping properties)	1500.0
additional parameter 1 (Volatile Organic Compound)	4000.0
additional parameter 2 (Heavy Metal Content (Pb, Cr ,Cd ,Arsenic, Antimony &Mercury))	2500.0

344

IS 15489 : 2013 NTH ER (2013) - PAINT, PLASTIC EMULSION — SPECIFICATION

PAINT, PLASTIC EMULSION — SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2 (Conditions in the Container)	600.0
6.3 (Thinning)	600.0
6.4 (Application Properties)	600.0
6.5 (Mass in kg/10 litre)	700.0
6.6 (Opacity)	700.0
6.7 (Fastness to Light (Xenon Arc apparatus for 500 hrs))	25000.0
6.8 .1.1 (C-2 Durability Test (Normal Outdoor Exposure Test 12 Months ) for Exterior Use Only)	10000.0
6.9 (Lead Restriction)	700.0
6.10 (Keeping Properties (For 12 months))	5000.0
6.11 (i) Table 1 (Consistency)	700.0
6.11(ii) Table 1 (Drying time, a) Surface Dry)	400.0
6.11(ii) Table 1 (Drying time b) Hard dry)	400.0
6.11 (iii) Table 1 (Finish)	700.0
6.11 (iv) (Gloss at 60 Deg. Angle)	700.0
6.11(v) Table 1 (Colour)	300.0
6.11(vii) Table 1 (Resistance to alkali)	700.0
6.11 (viii) Table 1 (Washability and cleanability)	700.0
6.11 (x) Table 1 (Recoating properties)	200.0
6.12.2 Specific requirements VOC (Volatile Organic Compounds (VOC) % by mass)	2400.0
6.12 .2 Toxic metals (toxic metals such as lead, cadmium, chomium (VI) and their compounds)	2400.0
6.11 ix) Table 1 (Accelerated Storage Stability)	1000.0

345

IRS-GE-1 (2016) - Specifications for Track ballast (IRS-GE-1)

Specifications for Track ballast (IRS-GE-1)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.2.1 (Aggregate abrasion Value (IS 2386(IV):1963))	2500.0
2.2.2 (Aggregate Impact Value (IS 2386(Part IV):1963))	2500.0
2.2.3 (Water absorption ( IS 2386 (III):1963))	1000.0
2.3 (Size and Gradation (as per annexure IV of IRS-GE-1,June 2016))	2000.0

346

IRS-GE-I, JUNE-2016 (2016) - SPECIFICATIONS FOR TRACK BALLAST

SPECIFICATIONS FOR TRACK BALLAST

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.3 (Size and Gradation (IRS-GE-I, JUNE-2016))	2000.0
2.2.3 (Water absorption (IS 2386 (Part III):1963))	1000.0
2.2.1 (Aggregate abrasion value-Annexure I of IRS- GE-I, June 2016 & IS 2386 (Part IV):1963)	1500.0
2.2.2 (Aggregate Impact Value-Annexure II of IRS- GE-I, June 2016 & IS 2386 (Part IV):1963)	1500.0
- (Elongation Index : {as per IS 2386 (1)})	1500.0

347

IS 9103 (1999) - Specification for Concrete Admixtures -

Specification for Concrete Admixtures -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2.1 (Slump of Control Concrete Mix at 15 Minutes)	2000.0
7.2.4 (Bleeding concrete additive)	2000.0
8.2.3 (Length change concrete additive)	2000.0
8.2.2 (Comparative Flexural strength for three duration of concrete additive)	10000.0
8.2.2 (Flexural strength for one duration of concrete additive)	5000.0
8.2.1 (Comparative Compressive strength for one duration of concrete)	5000.0
8.2.1 (Comparative Compressive strength for three duration of concrete)	10000.0
7.2.3 (Setting time of concrete additive allowable Deviation from control sample)	2000.0
7.2.5 (Water content of Concrete additive)	1000.0
9 (pH)	1000.0
9 (Chloride ion content)	1000.0
9 (Relative density)	1000.0
9 (Ash content)	1000.0
9 (Dry Material content)	1000.0
9 (Colour (as per IS 9103))	1000.0
Customer request (Sulphate)	1000.0
Customer request (Nitrate)	1000.0
Customer request (Thiocyanate)	1000.0

348

IS 2694 :2018 - School Chalks -Moulded,White-Specification

School Chalks -Moulded,White-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Materials)	1000.0
3.2 (Finish)	1000.0
3.3 (Hardness)	1000.0
3.4,Table 1 (Calcium sulphate(CaSO4.2H2O))	2000.0
3.4,Table 1 (Free Moisture)	1000.0
3.4,Table 1 (Length of sticks)	1000.0
3.4,Table 1 (Diameter of Thicker end)	1000.0
3.4,Table 1 (Mass per 100 sticks)	1000.0
3.4,Table 1 (Transverse breaking strength)	2000.0
3.1 (Test for free from Poisonous & Toxic materials)	5000.0

349

IS 4222:2018 - Coloured Chalks, Moulded-Specification

Coloured Chalks, Moulded-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Materials)	1000.0
3.1.1 & 3.2 (Freedom from Poisonous and Toxic Materials & Colours)	5000.0
3.3 (Finish)	1000.0
3.4 (Performance)	1000.0
3.1 (Calcined gypsum quality)	2000.0
3.5 (Free moisture)	1000.0
3.5,Table 1 (Length of sticks)	1000.0
3.5,Table 1 (Diameter at thicker end)	1000.0
3.5,Table 1 (Weight per 100 sticks)	1000.0
3.5,Table 1 (Transverse breaking strength)	2000.0

350

MORTH/ASTM - Mix Macadam

Mix Macadam

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
406.2.1.1 (Water absorption)	1000.0
406.2.1.1 (Soundness)	2000.0
406.2.1.1 Table 400.12.1 (Los Angeles Abrasion value)	1500.0
406.2.1.1 Table 400.12.1 (Aggregate Impact value)	1500.0
406.2.1.1 Table 400.12.2 (Combined Flakiness and Elongation Indices (Total))	3000.0
406.2.1.2 Table 400.13 (Grading Requirements of Aggregates for Wet Mix Macadam)	5000.0
406.2.1.2 (Plasticity Index (PI))	1000.0
406.2.1.2 (Liquid Limit)	1000.0
406.2.1.2 (Plastic Limit)	1000.0

351

IS 16415 (2015) - Composite cement - Specification

Composite cement - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Alkali Content)	1200.0
6.1 (Chloride content)	1200.0
6.1 (Loss on ignition)	1200.0
6.1 (Sulphide sulphur (S))	1200.0
6.1 (Total Sulphur content calculated as sulphuric anhydride(SO3))	1200.0
6.1 (Magnesia)	1200.0
6.1 (Insoluble residue)	1200.0
13 (Test for Consistency)	500.0
Table 3,i (Fineness)	1000.0
Table 3,ii,a (Soundness-by Le-chatelier method)	500.0
Table 3,ii,b (Soundness -by Autoclave method)	500.0
Table 3,iii,a (Setting Time-Initial)	250.0
Table 3,iii,b (Setting Time-Final)	250.0
Table-3 (Compressive strength - 24 h (±) 30 min)	1000.0
Table-3,iv,b (Compressive strength-168(±)2 h)	1000.0
Table-3,iv,c (Compressive strength-672(±)4 h)	1000.0
Table-3,v (Drying shrinkage)	1000.0
Table-3,iv,a (Compressive strength-72(±)1 h)	1000.0

352

IRC 105:2019 (DBM+BC)/(ASTM D 2041/AASHTO T 166/ASTM D2172/ASTM D 6307) - Specification for Dense Bituminous Macadam and Bituminous content for airfield Pavements

Specification for Dense Bituminous Macadam and Bituminous content for airfield Pavements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of DBM core (Aashto T 166/ASTM D 2041))	3000.0
2 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of BC core (Aashto T 166/ASTM D 2041))	3000.0
3 (Bitumen content/Binder content of DBM core(ASTM D2172/ASTM 6307/IRC:SP:20-2002))	3000.0
4 (Bitumen content/Binder content of BC core(ASTM D2172/ASTM 6307/(IRC-SP-20-2002))	3000.0
- (Binder content/Bitumen content -DBM(IRC-SP-20-2002))	3000.0
- (Binder content/Bitumen content -DAC(IRC-SP-20-2002))	3000.0
- (Binder content/Bitumen content -SDAC(IRC-SP-20-2002))	3000.0
1 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of DAC core (Aashto T 166/ASTM D 2041))	3000.0
1 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of SDAC core (Aashto T 166/ASTM D 2041))	3000.0
custom (Thickness)	1000.0
3.1.5 (Aggregate Gradation)	2000.0
3.3.5 (Degree of Compaction Test)	1000.0
3.1.5 (Aggregate Gradation)	2000.0

353

IRC 111-2009 (DBM) & AASHTO T 166 - Specifications for Dense graded Bituminous mixes-(DBM)

Specifications for Dense graded Bituminous mixes-(DBM)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test for Density/Bulk density/ Theoretical Maximum specific gravity/Bulk specific gravity:(Aaashto-T 166/ASTM D 2041))	3000.0
2 (Test for Bitumen/Binder content (ASTM 2172/ASTM D 6307/IRC:SP:20 (2002)))	3000.0

354

IS 2720 (Soil) (1987) - Method of Test for Soil.

Method of Test for Soil.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

355

IS 14543 (2024) - Packaged Drinking Water (other than Packaged Natural Mineral Water) - Specification

Packaged Drinking Water (other than Packaged Natural Mineral Water) - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2.9 (Vibrio parahaemolyticus)	1200.0
5.2.9 (Vibrio cholerae)	1200.0
5.2.8 (Shigella)	1200.0
5.2.8 (Salmonella)	1200.0
5.2.7 (Yeast & Mould)	1200.0
5.2.6 (Aerobic microbial count/ ml at 37° ± 1° C in 24 hours)	1200.0
5.2.6 (Aerobic microbial count/ ml at 20-22 °C in 72 hours)	1200.0
5.2.5 (Pseudomonas aeruginosa)	1200.0
5.2.4 (Sulphite reducing Anaerobes)	1200.0
5.2.3 (Staphylococcus aureus)	1200.0
5.2.3 (Faecal Streptococci)	1200.0
5.2.2 (Coliform)	1200.0
5.2.1 (Escherichia coli)	1200.0
5.3 (Total dissolved solids)	1000.0
5.3 (Bromate (as BrO3))	1200.0
5.3 (Sulphate (as SO4))	1200.0
5.3 (Lead (as Pb))	1000.0
5.3 (Zinc (as Zn))	1000.0
5.3 (Aluminium (as Al))	1000.0
5.4.1 (Annex D) (o, p-DDT)	5000.0
5.3 (Iron (as Fe))	1200.0
Custom (Total Aerobic microbial count at 37 °C in 48 hrs or 72 hrs)	1000.0
Custom (Total Aerobic microbial count at 30 °C in 72 hrs)	1000.0
5.3 (Copper (as Cu))	1200.0
5.3 (Manganese (as Mn))	1200.0
5.3 (Selenium (as Se))	1000.0
5.3 (Chromium (as Cr))	1000.0
5.3 (Nickel (as Ni))	1000.0
5.3 (Cadmium (as Cd))	1000.0
5.3 (Mercury (as Hg))	2000.0
5.3 (Colour, true colour units)	1200.0
5.3 (Odour)	1000.0
5.3 (Turbidity)	1000.0
5.3 (pH)	1000.0
5.3 (Barium (as Ba))	1000.0
5.3 (Nitrate (as NO3))	1000.0
5.3 (Nitrite (as NO2))	1000.0
5.3 (Fluoride (as F))	1000.0
5.3 (Silver (as Ag))	1000.0
5.3 (Chloride (as Cl))	1000.0
5.3 (Alkalinity (as HCO3))	1000.0
5.3 (Calcium (as Ca))	1000.0
5.3 (Magnesium (as Mg))	1000.0
5.3 (Sodium (as Na))	1000.0
5.3 (Residual free chlorine)	1000.0
5.3 (Phenolic compounds (as C6H5OH))	1000.0
5.3 (Sulphide (as H2S))	1000.0
5.3 (Antimony (as Sb))	1000.0
5.3 (Borates (as B))	1000.0
5.3 (Arsenic (as As))	2000.0
5.3 (Cyanide (as CN))	2000.0
5.3 (Taste)	1000.0
5.4.1 (Annex D) (Methyl parathion)	5000.0

356

IS 1293 (2019) - Plugs and socket- outlets of rated Voltage up to and inculding 250 Volts and rated current up to and inculding 16 amperes-Specification(Fourth Revision)

Plugs and socket- outlets of rated Voltage up to and inculding 250 Volts and rated current up to and inculding 16 amperes-Specification(Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
31.1 (Type Test (6A))	7000.0
31.1 (Type Test (16A))	10000.0
31.1 (Type Test (6A & 16A))	12000.0
31.2 (Acceptance Test (6A))	5000.0
31.2 (Acceptance Test (16A))	7000.0
31.2 (Acceptance Test (6A & 16A))	9000.0

357

MORTH/ASTM - Bitumen BC/DBM/BM

Bitumen BC/DBM/BM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
505.3.5 (Density(ASTM-D2726))	2000.0
505.3.5 (Binder content(ASTM-D 2172))	5000.0

358

CUS/SR/MECH-20 (2023) - Specification for Hanger Shackle, dia 25 mm for PGCIL

Specification for Hanger Shackle, dia 25 mm for PGCIL

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Visual examination)	1000.0
2.0 (Dimensions, mm)	2000.0
3.1 (Tensile load, kN)	1500.0
3.2 (Proof load, kN)	1500.0
4.0 (Hardness)	3000.0
7.0 (Chemical composition, % by mass)	5000.0
5.1 (Thickness of Zinc coating)	2000.0
5.2 (Mass of Zinc coating)	2000.0
5.3 (Uniformity of Zinc coating)	1000.0
9.1 (Grain size)	3000.0
9.2 (Grain flow)	3000.0
10.0 (Inclusion rating)	4000.0
6.0 (Adhesion test)	1000.0
8.0 (Magnetic particle inspection (after stripping of galvanization))	2000.0

359

IS 17876 (2022) - Stainless Steel Welded Pipes and Tubes for General Services - Specification

Stainless Steel Welded Pipes and Tubes for General Services - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clauses 8.1 and 8.2 (Carbon (as C))	1000.0
Clauses 8.1 and 8.2 (Silicon (as Si))	1000.0
Clauses 8.1 and 8.2 (Manganese (as Mn))	1000.0
Clauses 8.1 and 8.2 (Nickel (as Ni))	1000.0
Clauses 8.1 and 8.2 (Chromium (as Cr))	1000.0
Clauses 8.1 and 8.2 (Molybdenum (as Mo))	1000.0
Clauses 8.1 and 8.2 (Sulphur (as S))	1000.0
Clauses 8.1 and 8.2 (Phosphorus (as P))	1000.0
Customer request (Weight per meter, kg/m)	1000.0
10.1 (Tensile Strength, MPa)	1000.0
10.1 (Yield Strength, MPa)	1000.0
10.1 (Percent Elongation, %)	1000.0
24 (Outside Diameter, mm)	1000.0
24 (Wall Thickness, mm)	1000.0
8 (Chemical Composition - Ladle Analysis as per IS 228 and its relevant parts or any other established instrumental/chemical method)	5000.0

360

IS 17875 (2022) - Stainless Steel Seamless Pipes and Tubes for General Services

Stainless Steel Seamless Pipes and Tubes for General Services

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 & 8.2 (Carbon) (Carbon (as C))	1000.0
8.1 & 8.2 (Silicon) (Silicon (as Si))	1000.0
8.1 & 8.2 (Manganese) (Manganese (as Mn))	1000.0
8.1 & 8.2 (Nickel) (Nickel (as Ni))	1000.0
8.1 & 8.2 (Chromium) (Chromium (as Cr))	1000.0
8.1 & 8.2 (Molybdenum) (Molybdenum (as Mo))	1000.0
8.1 & 8.2 (Sulphur) (Sulphur (as S))	1000.0
8.1 & 8.2 (Phosphorus) (Phosphorus (as P))	1000.0
10.1 (Tensile Strength)	1000.0
10.1 (Yield Strength)	1000.0
10.1 (Percent Elongation)	1000.0
12 (HARDNESS TEST FOR TUBES)	2000.0
8 (Chemical Composition)	5000.0