| 331 |
Custom specification- Bipolar for metro rail (general chemical) - Custom specification- Bipolar for metro rail (general chemical) |
Custom specification- Bipolar for metro rail (general chemical) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Appearance) |
500.0 |
|
| - (Odour) |
500.0 |
|
| - (Skin Irritation) |
500.0 |
|
| - (pH Value) |
1000.0 |
|
| - (Viscosity by Flow cup) |
1000.0 |
|
| - (Accelerated Corrosion test ( For 21 Hours) with raw water) |
1500.0 |
|
| - (Accelerated Corrosion (for 21 hours) with Bipolar) |
1500.0 |
|
| - (Specific Gravity) |
1000.0 |
|
|
| 332 |
IS 8986 (2022) (2022) - Hexagonal Integral Drill Steel and Extension Rods and Hollow Round Drill Steel in Bar Form — Dimensions
(Second Revision) |
Hexagonal Integral Drill Steel and Extension Rods and Hollow Round Drill Steel in Bar Form — Dimensions
(Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 2 (Dimension - Hexagonal Integral Drill Steel and Extension Rods in mm Clause 2.1 and Table 1 of IS 8986 or any other relevant National & International Standard Specified) |
1000.0 |
|
| 2 (Dimension -Hollow Round Drill Steel in Bar Form for Extension Rods, in mm, Clause 2.2, Table 2 of IS 8986 or any other national or International Stanard specified) |
1000.0 |
|
| 2 (Mass per Meter in Kg/M as per Table 1 or 2 of IS 8986 or any other National or International Standard specified.) |
1000.0 |
|
| 0 (Rockwell Hardness Test in HRC) |
2000.0 |
|
| 0 (Mechanical Properties - Tensile Strength, Yield Strength and % of Elongation as per IS 1608 Prt-1 or ASTM E8 or any other relevant National or International specification.) |
4000.0 |
|
| 2 (Sectional Area in mm2 as per IS 8986 Clause 2 Table 1 /Table 2) |
1000.0 |
|
| 0 (Chemical Composition in mass% by OES method or any other National or International product specification specified test method.) |
3500.0 |
|
|
| 333 |
IS 17044 (2018) - Intumescent fire retardant paint (Water Based) - Specification |
Intumescent fire retardant paint (Water Based) - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Intumescent fire retardant paint (Water Based) - Specification (Please refer to the annexure for the test result) |
10000.0 |
|
|
| 334 |
IS 5758 (2020) - Precast Concrete Kerbs, Channels, Edgings, Quadrants and Gutter Aprons |
Precast Concrete Kerbs, Channels, Edgings, Quadrants and Gutter Aprons |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 9.2 (Dimensions, Overall Length, in mm) |
500.0 |
|
| 9.2 (Dimensions, Overall Height, in mm) |
500.0 |
|
| 9.2 (Overall Thickness, in mm) |
500.0 |
|
| 9.3 (Bending Strength, N/mm^2) |
4000.0 |
|
| 9.4 (Water Absorption, in %) |
2000.0 |
|
| 4.2 (Shape and Profile) |
1000.0 |
|
|
| 335 |
IS 15961 (2012) - Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain) |
Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 9 (Triple Spot Coating Mass) |
2000.0 |
|
|
| 336 |
IS 15965 : 2012 (2012) - Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain) |
Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.3 (Total Coated Thickness (As received condition), mm) |
1000.0 |
|
| 8 (Tensile Strength (As per IS 15961), MPa) |
1000.0 |
|
| 8 (Yield Strength (As per IS 15961), MPa) |
1000.0 |
|
| 8 (% Elongation (As per IS 15961), %) |
1000.0 |
|
| 7.1 (Mass of Coating (Both sides), g/m²) |
2000.0 |
|
| 5 (Chemical composition (As per IS 513), % by mass) |
2500.0 |
|
| 1 (Composition of AZ Coating Material in %) |
3000.0 |
|
|
| 337 |
Customized Specification for Plastic Bottle with cap - Customized Specification for Plastic Bottle with cap |
Customized Specification for Plastic Bottle with cap |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Identification of Plastic bottle body by FTIR) |
2000.0 |
|
| - (Identification of plastic cap by FTIR) |
2000.0 |
|
|
| 338 |
- (2025) - Customize General chemical specifical NTH (WR) |
Customize General chemical specifical NTH (WR) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Appearance) |
500.0 |
|
| - (Specific gravity) |
1000.0 |
|
| - (Releasing Properties) |
3000.0 |
|
| - (Flash Point by COC) |
1000.0 |
|
| - (Fire Point by COC) |
1000.0 |
|
| - (Aluminium Reactivity at 60 deg. C for 72 hours) |
1000.0 |
|
| - (Effect on Wooden Ply at 60 deg C. for 72 hours) |
1000.0 |
|
| - (Viscosity by Flow Cup) |
1000.0 |
|
|
| 339 |
16720 (2018) - Pulverized Fuel Ash - Cement Bricks |
Pulverized Fuel Ash - Cement Bricks |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8.1 (General) |
500.0 |
|
| 8.2 (Dimension, Length, in mm) |
500.0 |
|
| 8.2 (Dimensions, Width) |
500.0 |
|
| 8.2 (Dimensions, Thickness, in mm) |
500.0 |
|
| 8.3 (Density, in kg/m^3) |
1000.0 |
|
| 8.4 (Compressive Strength, in N/mm^2) |
2000.0 |
|
| 8.5 (Drying Shrinkage, in %) |
2000.0 |
|
| 8.6 (Water Absorption Test) |
1000.0 |
|
|
| 340 |
IS 18387 (2023) - Gypsum Ceiling Tiles |
Gypsum Ceiling Tiles |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7.1.1 (Dimensions and Tolerances on size, Length in mm) |
500.0 |
|
| 7.1.1 (Dimensions and Tolerances on Size, Width) |
500.0 |
|
| 7.1.2 (Dimensions and Tolerances on Edges Profile) |
500.0 |
|
| 7.2.2 (Tolerances on Squareness of Edges,) |
500.0 |
|
| 7.3 (Density, in kg/m^3) |
1000.0 |
|
| 7.4 (Flexural Breaking Strength (Length wise), in N) |
2000.0 |
|
| 7.4 (Flexural Breaking Strength (Across the length), in N) |
2000.0 |
|
| 7.5 (Water Absorption, in %) |
1000.0 |
|
| 7.8 (Humidified Deflection, in mm) |
5000.0 |
|
|
| 341 |
Customized Specification for Plastic Material - Customized Specification for Plastic Material |
Customized Specification for Plastic Material |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Material Identification by FTIR) |
2000.0 |
|
| - (Hardness) |
1000.0 |
|
|
| 342 |
Customized specification for T Shirt - Customized specification for T Shirt |
Customized specification for T Shirt |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Size) |
500.0 |
|
| - (Material(composition)) |
2000.0 |
|
| - (Mass of material) |
1000.0 |
|
| - (Knitting) |
500.0 |
|
| - (Lining) |
500.0 |
|
| - (Neck type) |
500.0 |
|
| - (Sleeve) |
500.0 |
|
| - (Pocket) |
500.0 |
|
| - (Logo) |
500.0 |
|
|
| 343 |
Customized specification for peak cap - Customized specification for peak cap |
Customized specification for peak cap |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Material) |
2000.0 |
|
| - (Diameter) |
500.0 |
|
| - (Peak) |
500.0 |
|
| - (Complete height(Peak to top)) |
500.0 |
|
| - (Side button of white metal with steel emblem) |
500.0 |
|
| - (Width of leather strip) |
500.0 |
|
| - (Inner side material) |
500.0 |
|
| - (Band Patti) |
500.0 |
|
|
| 344 |
Customized Specification for Bag - Customized Specification for Bag |
Customized Specification for Bag |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Type of Bag) |
500.0 |
|
| - (Main Outside material) |
2000.0 |
|
| - (Inside material) |
500.0 |
|
| - (Material of straps/Tapes/webbing) |
2000.0 |
|
| - (Slide fasteners) |
1000.0 |
|
| - (Side Pocket material (for bottle)) |
1000.0 |
|
| - (Backside material(for backpack)) |
2000.0 |
|
| - (Number of inside compartment(full pockets)) |
500.0 |
|
| - (Number of inside patch pockets) |
500.0 |
|
| - (Water resistance) |
500.0 |
|
| - (Height) |
500.0 |
|
| - (Width) |
500.0 |
|
| - (Depth) |
500.0 |
|
| - (Type of Logo) |
500.0 |
|
| - (Buckle material) |
2000.0 |
|
|
| 345 |
CUS/SR/MECH-22 - Stainless Steel Insu-Roti Saver (Mini) |
Stainless Steel Insu-Roti Saver (Mini) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Dimensions) |
2000.0 |
|
| 2.0 (Weight) |
500.0 |
|
| 3.0 (Capacity) |
1000.0 |
|
| 4.0 (Chemical composition, % by mass) |
3000.0 |
|
|
| 346 |
IS 6603 (2024) - Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars — Specification (2nd Revision) |
Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars — Specification (2nd Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6 (Freedom From Defects - Visual Examination as per IS 6603 Cl.6.1 & 6.2) |
1000.0 |
|
| 7 (Chemical Composition-The ladle analysis of steel, when carried out either by the methods specified in relevant parts of IS 228 or any other established international instrumental/chemical method) |
5000.0 |
|
| 9.0 Mechancial Properites (The tensile test ( Tensile Stregth, 0.2% Proof/Yield Stress, % of Elongation ) shall be carried out in accordance with IS 1608 (Part 1)) |
3000.0 |
|
| 9.0 Mechancial Properties (Hardness shall be determined in accordance with IS 1500 (Part 1), IS 1501 (Part 1) or IS 1586
(Part 1).) |
2000.0 |
|
| 9.0 Mechanical Properties (Charpy impact test shall be carried out in accordance with IS 1757 (Part 1).) |
5000.0 |
|
| 12 (Dimesnion Measurment in mm
dimensional tolerances for the bars and flats shall be as laid down in Table 26 to Table 36 given at Annex C of IS 6603) |
1000.0 |
|
| 14 (Corrosion Resistance Test - The material shall be tested for corrosion resistance as per IS 10461 (Part 1) or ISO 3651 (Part 2) or any other method) |
10000.0 |
|
|
| 347 |
RDSO/2020/GE:IRS-0004 (2020) - Comprehensive Guidelines and Specification for Railway Formation |
Comprehensive Guidelines and Specification for Railway Formation |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.8 (Gradation of Particles, % passing) |
5000.0 |
|
| 3.8 (Particle passing 75 microns, %) |
1000.0 |
|
| 3.8 (Coefficient of Curvature) |
1500.0 |
|
| 3.8 (Uniformity Coefficient) |
1500.0 |
|
| 3.8 (California Break Ration (CBR in Dry condition) Test) |
7000.0 |
|
| 3.8 (California Break Ration (CBR in Wet Condition)) |
7000.0 |
|
| 3.8 (Aggregate Abrasion Value (Los Angeles), %) |
2000.0 |
|
| 3.8 (Aggregate Impact Value, %) |
2000.0 |
|
| - - (Atterberg Limits) |
3000.0 |
|
| Fig. 3.8 (Enveloping Curves for Blanket Material from Sieve Analysis) |
1000.0 |
|
| 3.8 (Maximum Dry Density & Optimum Moisture Content (OMC & MDD)) |
5000.0 |
|
|
| 348 |
RDSO/2020/GE:IRS-0004/September 2020 (Including ACS No 01 dated 16.12.2021) - Comprehensive guidelines and Specifications for Railway formation |
Comprehensive guidelines and Specifications for Railway formation |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7.3.2.C.1 (The Uniformity of Co-efficient(Cu):(as per IS 2720(1)1983/IS 1498:1970)) |
1500.0 |
|
| 7.3.2.C.1 (The Co-efficient of Curvature -Cc (IS 2720(1):1983/IS 1498(1970)) |
1500.0 |
|
| 7.3.2.C.1 (Percentage of Fines(Passing 75 micron)-IS 2720(1):1983/IS 1498:1970) |
1000.0 |
|
| 7.3.2.C.2 (CBR test) |
6000.0 |
|
| 7.3.2.C.3 (Los angeles abrasion value) |
1500.0 |
|
| 7.3.2.C.6 (Checking of forming with enveloping curves) |
2000.0 |
|
| 6.2.8.C (OMC &MDD (IS 2720(8)):1983) |
5000.0 |
|
|
| 349 |
IS/RDSO-GE/0001:23 (2023) - Specification for Track Ballast |
Specification for Track Ballast |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 2.2 (Aggregate Abrasion Value, Average Value in %) |
2000.0 |
|
| 2.2 (Aggregate Impact Value, Average value in %) |
2000.0 |
|
| 2.2.3 (Water Absorption, in %) |
1000.0 |
|
| 2.3 (Sieve Analysis, Retention on 65mm sq. mesh sieve, in %) |
1000.0 |
|
| 203 (Sieve Analysis, Retention on 40mm sq. mesh sieve, in %) |
1000.0 |
|
| 2.3 (Sieve Analysis, Retention on 20mm sq. mesh sieve, in %) |
1000.0 |
|
|
| 350 |
- - Custom Specification for Analysis-General Chemical (WR) |
Custom Specification for Analysis-General Chemical (WR) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Ash Content%) |
1500.0 |
|
|
| 351 |
Customized specification for VIP frenchie Pro Brief Colour 90 cm. as per TDS Index no. 41294 - Customized specification for VIP frenchie Pro Brief Colour 90 cm. as per TDS Index no. 41294 |
Customized specification for VIP frenchie Pro Brief Colour 90 cm. as per TDS Index no. 41294 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Nomenclature) |
500.0 |
|
| - (Identification Mark/Marking) |
500.0 |
|
| - (Fibre Composition) |
1000.0 |
|
| - (Count) |
500.0 |
|
| - (Dimensional Change) |
1000.0 |
|
| - (Wales and Course) |
500.0 |
|
| - (pH) |
1000.0 |
|
| - (Colour fastness to washing) |
1000.0 |
|
| - (Size) |
500.0 |
|
| - (Waist band width) |
500.0 |
|
| - (Side length(including waist band)) |
500.0 |
|
| - (Full width flat) |
500.0 |
|
| - (Centre height (including waist band)) |
500.0 |
|
| - (Pouch with front(bottom)) |
500.0 |
|
| - (Half leg open) |
500.0 |
|
| - (Width of top elastic) |
500.0 |
|
|
| 352 |
Customized specification for VIP FRENCHIE COLOURED 85 CMS as per TDS Index no. 41546 - Customized specification for VIP FRENCHIE COLOURED 85 CMS as per TDS Index no. 41546 |
Customized specification for VIP FRENCHIE COLOURED 85 CMS as per TDS Index no. 41546 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Nomenclature) |
500.0 |
|
| - (Identification Mark/Marking) |
500.0 |
|
| - (Fibre Composition) |
1000.0 |
|
| - (Count) |
500.0 |
|
| - (Wales and Course) |
500.0 |
|
| - (pH value) |
1000.0 |
|
| - (Size) |
500.0 |
|
| - (Waist band width) |
500.0 |
|
| - (Side length) |
500.0 |
|
| - (Full width flat) |
500.0 |
|
| - (Central height(including waist band)) |
500.0 |
|
| - (Pouch width(bottom)) |
500.0 |
|
| - (Half leg open) |
500.0 |
|
| - (Width of inner elastic) |
500.0 |
|
|
| 353 |
Customized specification for Camber Tray Set as per TDS Index no. 34442 - Customized specification for Camber Tray Set as per TDS Index no. 34442 |
Customized specification for Camber Tray Set as per TDS Index no. 34442 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Dimensions of Camber large tray) |
500.0 |
|
| - (Dimensions of camber medium tray) |
500.0 |
|
| - (Dimensions of camber small tray) |
500.0 |
|
| - (Weight of camber large tray) |
500.0 |
|
| - (Weight of camber medium tray) |
500.0 |
|
| - (Weight of camber small tray) |
500.0 |
|
| - (Colour) |
500.0 |
|
| - (Material Identification) |
2000.0 |
|
| - (Identification mark/marking) |
500.0 |
|
| - (Design) |
500.0 |
|
|
| 354 |
Custom specification CSD Canteen Chemical Lab samples - Custom specification CSD Canteen Chemical Lab samples |
Custom specification CSD Canteen Chemical Lab samples |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Camphor analysis (Please refer annexure for the test result of Camphor samples) |
6000.0 |
|
| AGARBATTlS - SPECIFICATION (Please refer annexure for the test result (Agarbattis/Incense sticks)) |
7000.0 |
|
| Cosmetic products (Please refer annexure for the test results) |
5000.0 |
|
| Custom specification CSD Canteen Chemical Lab samples (Please referred annexure for the test result (Dish Washing Liquid)) |
5000.0 |
|
| Custom specification CSD Canteen Chemical Lab samples (Please referred annexure for the test result (Dish Wash Bar)) |
5000.0 |
|
| Custom specification CSD Canteen Chemical Lab samples (Please referred annexure for the test result (Floor Cleaner)) |
5000.0 |
|
| Custom specification CSD Canteen Chemical Lab samples (Please referred annexure for the test result) |
5000.0 |
|
|
| 355 |
Customized Specification for Non Metallic Liners/Packing Plates for Use in CASBUS Bogies - Customized Specification for Non Metallic Liners/Packing Plates for Use in CASBUS Bogies |
Customized Specification for Non Metallic Liners/Packing Plates for Use in CASBUS Bogies |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Specific Gravity as per ASTM D 790) |
1000.0 |
|
| - (Hardness as per ASTM D 2240) |
1000.0 |
|
| - (Tensile Strength at yield as per ASTM D 638) |
2000.0 |
|
| - (Flexural Modulus as per ASTM D 790) |
2000.0 |
|
| - (Water absorption at 23(+/-)1deg.C for 24(+1/2, -o)hours) |
2000.0 |
|
|
| 356 |
17908 (2023) - Fibre Cement Sheet - Lightweight Concrete Sandwich Panels |
Fibre Cement Sheet - Lightweight Concrete Sandwich Panels |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.2 (Overall Length, in mm) |
1000.0 |
|
| 6.2 (Overall Width, in mm) |
1000.0 |
|
| 6.2 (Thickness, in mm) |
1000.0 |
|
| 6.2 (Indentation Depth, in mm) |
500.0 |
|
| 6.2.1.1 (Straightness of Edge, in mm/m) |
1000.0 |
|
| 6.2.1.2 (Squareness of edge, in mm/m) |
1000.0 |
|
| 6.3 (Density, in kg/m^3) |
1000.0 |
|
| 6.4.1 (Bending Strength (Three Point Loading), N/mm^2)) |
4000.0 |
|
| 6.4.2 (Bending Strength (Uniformly Distributed Load), in N/m^2) |
4000.0 |
|
| 6.5 (i) (Impact Test (Small Hard Body impact - Surface damage),) |
1500.0 |
|
| 6.5 (i) (Impact Test (Small hard body impact - Perforations)) |
1500.0 |
|
| 6.5 (ii) (Impact Test (Large soft body impact), deformation in mm) |
1500.0 |
|
| 6.6.2 (Tensile Strength, in N/mm^2) |
2000.0 |
|
| 6.6.3 (Screw Withdrawal Strength, in kN) |
1500.0 |
|
|
| 357 |
303 (2024) - Plywood for General Purpose |
Plywood for General Purpose |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8.1 (Length, in mm) |
400.0 |
|
| 8.1 (Width, in mm) |
400.0 |
|
| 8.2 (Thickness, in mm) |
400.0 |
|
| 8.3 (Squareness, in mm/m) |
400.0 |
|
| 8.3 (Edge Straightness, in mm/m) |
400.0 |
|
| 5 (Classification by Appearance) |
1500.0 |
|
| 9 (Workmanship and finish,) |
2000.0 |
|
| 11.3.1 (a) (Glue Adhesion - Water Resistance Test) |
2000.0 |
|
| 11.3.1 (b) (Glue Adhesion Test - Water Resistance Test - BWR Grade) |
2000.0 |
|
| 11.3.1 cb) (Glue Adhesion Test - Water Resistance Test - BWP Grade) |
2000.0 |
|
| 11.3.2 (Mycological Test) |
1500.0 |
|
| 11.4 (Moisture Content, in %) |
1000.0 |
|
| 11.5 (Static Bending Strength (Modulus of Rupture -Along), in N/mm^2) |
750.0 |
|
| 11.5 (Static Bending Strength (Modulus of Rupture - Across), in N/mm^2) |
750.0 |
|
| 11.5 (Static Bending Strength (Modulus of Elasticity-Along), in N/mm^2) |
750.0 |
|
| 11.5 (Static Bending Strength (Modulus of Elasticity- Across), in N/mm^2) |
750.0 |
|
|
| 358 |
CUS/SR/MECH-55 (2024) - Mechanical Properties of Metal |
Mechanical Properties of Metal |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Dimensions, mm) |
2000.0 |
|
| 2.0 (Brinell Hardness, HBW) |
2000.0 |
|
| 5.0 (Powder Coating Thickness, micron) |
2000.0 |
|
| 6.0 (Tensile strength, N/mm²) |
1000.0 |
|
| 7.0 (Yield strength, N/mm²) |
1000.0 |
|
| 8.0 (Percentage Elongation, %) |
1000.0 |
|
| 9.0 (Weight, kg) |
1000.0 |
|
|
| 359 |
CUS/SR/MECH-8 - Composite Sandwich Shutter |
Composite Sandwich Shutter |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Deflection) |
3000.0 |
|
| 2.0 (Breaking load) |
3000.0 |
|
|
| 360 |
CUS/SR/MECH-14 - Trek Bottle |
Trek Bottle |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Height) |
1000.0 |
|
| 2.0 (Weight) |
1000.0 |
|
| 3.0 (Capacity) |
1000.0 |
|
| 4.0 (Hot water test) |
3000.0 |
|
| 5.0 (Cold water test) |
3000.0 |
|
| 6.0 (Chemical composition, % by mass) |
6000.0 |
|
|
