NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director.nthwr-ca@gov.in

Scope List

Reset

637 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

301

IS 2645:2003 (RA 2017) - Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2.a. (Setting time -Initial)	500.0
3.2.b (Setting time-Final)	500.0
3.1 (Permeability to water(IS 2645:2003 Annex B))	3000.0
3.3.a (Compressive strength-3 days)	2000.0
3.3.b (Compressive strength-7 days)	2000.0
3.4 (Chloride content)	2000.0
- (Test for Heavy Metals by AAS method.)	2000.0
Toxic Elements (Toxic Elements (By AAS method))	3000.0
- - (VOC matter)	3000.0
- (pH)	1000.0

302

Custom Specification for General Chemical -1 - Custom Specification for General Chemical-1

Custom Specification for General Chemical-1

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Annexure (Results as per Annexure)	10000.0

303

Customized specification on the lines of ASTM D 430 - Standard Test Method For Rubber Deterioration-Dynamic Fatigue

Standard Test Method For Rubber Deterioration-Dynamic Fatigue

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Resistance to cracking(Number of cycles required for the first sign of crack))	5000.0

304

Customer specification - Flame retardant test for 4 hours

Flame retardant test for 4 hours

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
27600 (FLAME RETARDANT TEST FOR 4 Hrs.)	3000.0

305

ASTM D2240 (2015) - Standard Test Method for Rubber Property—Durometer Hardness

Standard Test Method for Rubber Property—Durometer Hardness

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

306

Custom CC Tiles, NTH(WR) - Cement Based Tiles - Terrazo

Cement Based Tiles - Terrazo

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 & 8.1 of IS 1237 (Dimension & Tolerances (On the lines of IS 1237), in mm)	500.0
7 & 8.1 of IS 1237 (Thickness and Thickness of wearing layer (on the lines of IS 1237), in mm)	500.0
12.2 of IS 1237 (Flatness of tiles (on lines of IS 1237 cl. 12.2), in %)	500.0
12.3 of IS 1237 (Perpendicularity of tiles (on lines of IS 1237 cl. 12.3), in %)	500.0
12.4 of IS 1237 (Straightness of tiles (on lines of IS 1237 cl. 12.4), in %)	500.0
12.5 of IS 1237 (Water Absorption (On lines of IS 1237 Cl. 12.5), in %)	1000.0
12.6 of IS 1237 (Wet Transverse Strength (On lines of IS 1237 Cl. 12.6), in %)	2000.0
12.7 of IS 1237 (Resistance to Wear (on the lines of IS 1237 Cl 12.7), in mm)	2000.0
Part 13 - IS 13630 (Scratch Hardness on Mho's Scale (One the lines of IS 13630 (Part 13)))	2000.0
Part 14 - IS 13630 (Drop Ball Impact Resistance (on lines of IS 13630 (Part 14)))	2000.0
6.1 of IS 3367 (Compressive Strength (on the lines of IS 3367), MPa)	2000.0
Part 4 of IS 13630 (Coefficient of Linear Thermal Expension (on the lines of IS 13630 -Part 4),)	3000.0
IS 101 (Gloss at 60 Deg. (on the lines of IS 101))	1200.0

307

IS 636 (2018) - Non-percolating flexible fire fighting delivery hose

Non-percolating flexible fire fighting delivery hose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (General Requirements-Inner Lining)	1500.0
6.2 (Internal Diameter, mm)	1000.0
6.3 (Length, m)	1000.0
6.4 (Mass, g)	1000.0
6.5 (Coil Diameter, cm)	1000.0
6.6 (Hydrostatic Proof Pressure Test)	5000.0
6.7 (Hydrostatic Burst Pressure Test)	5000.0
6.8 (Kink Test)	2000.0
6.9 (Change in Length, %)	1000.0
6.10 (Change in Diameter, %)	1000.0
6.11.1 (Adhesion, mm/minute)	2000.0
6.11.2 (Accelerated Ageing- Appearance)	1000.0
6.11.2 (Accelerated Ageing- Hydrostatic Burst Pressure Test)	5000.0
6.11.2 (Accelerated Ageing- Adhesion, mm/minute)	2000.0
6.12 (Abrasion Resistance)	2000.0
6.13 (Water Pick Up / Moisture Absorption, kg/Sq. m.)	1000.0
6.14 (Heat Resistance)	2000.0
6.15 (Oil Resistance Test- Appearance)	1000.0
6.15 (Oil Resistance Test - Adhesion)	2000.0

308

MICR Cheque Paper Sensitization to chemicals and UV Light - MICR Cheque Paper Sensitization to chemicals and UV Light

MICR Cheque Paper Sensitization to chemicals and UV Light

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test for Chemical Sensitization Ethanol)	450.0
2 (Test for Chemical Sensitization Acetone)	450.0
3 (Test for Chemical Sensitization Benzene)	450.0
4 (Test for Chemical Sensitization Chloroform)	450.0
5 (Test for Chemical Sensitization Ethylene Glycol")	450.0
6 (Test for Chemical Sensitization Bleaching powder)	450.0
7 (Test for Chemical Sensitization Ammonia solution 30%)	450.0
8 (Test for Chemical Sensitization Sodium meta bisulfite solution 10%)	450.0
9 (Test for Chemical Sensitization Oxalic acid solution 5%)	450.0
10 (Test for Exposure to UV lamp (for 24 Hours))	350.0
11 (GSM)	100.0

309

IS 14543 (2024) - Packaged Drinking Water (other than Packaged Natural Mineral Water) - Specification

Packaged Drinking Water (other than Packaged Natural Mineral Water) - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.3 (Total dissolved solids)	1000.0
5.3 (Sulphate (as SO4))	1200.0
5.3 (Lead (as Pb))	1000.0
5.3 (Zinc (as Zn))	1000.0
5.3 (Iron (as Fe))	1200.0

310

IS 4454 : Part 1 (2001) - Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Chemical Analysis)	2500.0
9 (Dimensions)	1000.0
10.1 (Tensile Strength)	3000.0
10.2 (Wrapping test)	1000.0
10.3 (Torsion Test)	1000.0

311

IS 12086 (2020) - Hydrazine Hydrate - Specification ( First Revision )

Hydrazine Hydrate - Specification ( First Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Annexure (Result as per Annexure)	5000.0

312

Two Component Road Marking Material - Two Component Road Marking Material (Cold Plastic Paint) as per customer requirement

Two Component Road Marking Material (Cold Plastic Paint) as per customer requirement

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Two component road marking material (Shore Hardness D (ASTM D 2240))	2000.0
Two component road marking material (Please refer the annexure)	10000.0

313

IS 2720 - Methods of Tests for Soils

Methods of Tests for Soils

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Grain size analysis- (IS 2720(Part 4):1985)	5000.0
2 (Determination of Liquid limit-(IS 2720(Part 5):1985))	1000.0
3 (Determination of Plastic Limit(IS 2720(Part 5):1985))	1000.0
4 (Determination of Plasticity Index-(IS 2720(Part 5):1985))	1000.0
5 (Determination of Water Content-Dry density relation using light compaction (IS 2720(Part 7):1980))	5000.0
6 (Determination of Water Content-Dry density relation using heavy compaction (IS 2720(Part 8):1983))	5000.0
7 (Laboratory determination of CBR (IS 2720(Part 16):1987))	6000.0
10 (Determination of Shrinkage limit (IS 2720(6)1972))	1000.0
- (Type of Soil-Classification & Identification of Soil (IS 1498:1970))	2000.0
- (Moisture content (IS:2720(Part 2):1973))	1000.0
- (Organic matter- (IS 2720(22):1972))	1200.0
- (pH)	1000.0
- (Total Soluble sulphates)	2000.0
- (Free swell index (Methods of test for soils: IS 2720 (Part 40) : 1977 Reviewed In : 2021))	2000.0
8 (Determination of Uniformity coefficient(Cu): (IS 1498:1970))	1500.0
9 (Determination of Coefficient of Curvature(Cc): (IS 1498:1970))	1500.0

314

15337 (2003) - Coal tar based anticorrosion tape for protection of underground mild steel pipelines - Specification

Coal tar based anticorrosion tape for protection of underground mild steel pipelines - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 4 (clause 4.5) (Solubility of Coal tar based tape in petrol (Annexure C of IS 15337 : 2003))	2000.0

315

Customized test on the lines of IS 636:2018 - Non percolating flexible fire fighting delivery hose

Non percolating flexible fire fighting delivery hose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Heat resistance test as per clause 6.14(Annexure E) (Requirement: None of the test samples shall burst at less than 20s of the application of the hot cube for Type 3 hose))	5000.0

316

IS 2967 (1983 RA 2019) - Specification for external micrometer (First Revision)

Specification for external micrometer (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Deviations and Tolerances)	1200.0
4 (Error of Measurement)	1200.0
4 (Deviations and Tolerances (For 0-100mm))	1500.0
4 (Deviations and Tolerances (above 300mm))	2500.0
4 (Error of Measurement (For 0-100mm))	1200.0
4 (Error of Measurement (For 200-300mm))	2000.0
4 (Error of Measurement)	1200.0

317

NSS-WR-Zinc in Dry Coating - Custom-Percent of Zinc Coating in Dry Coating

Custom-Percent of Zinc Coating in Dry Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Percent of Zinc Content in Dry Film)	2000.0

318

DKD-R 6-1 (2014) - Calibration of Pressure Gauges

Calibration of Pressure Gauges

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Pressure)	4000.0

319

Customized Specification for 3D printed specimen - Customized Specification for 3D printed specimen

Customized Specification for 3D printed specimen

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength (As per ASTM D 638))	4000.0
- (Flexural Strength (As per ASTM D 790))	4000.0
- (Izod Impact resistance(As per ASTM D 256))	4000.0
- (Shore Hardness/Durometer hardness (As per ASTM D 2240))	1000.0

320

Manufacture/Customer Specification - Test as per Manufacturer/Customer Specification

Test as per Manufacturer/Customer Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test as per Manufacture / Customer Specification)	25000.0
17 (LSZH Property)	20000.0

321

RDSO SPECIFICATION No. M&C/PCN/129/2018 (2018) - SPECIFICATION FOR EPOXY BASED ZINC RICH PRIMER (TWO PACK)

SPECIFICATION FOR EPOXY BASED ZINC RICH PRIMER (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Weight per epoxy equivalent on non-volatile vehicle content basis, (CL. 4 of IS 9162-79))	3000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, h, Max : a) Surface dry (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, Max b) Hard dry (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, Max C) Hard dry at 70 Deg C (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Consistency (IS 101 (Part 1/Sec 5)-89)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Finish (IS 101 (Part 3/Sec 4)))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Colour (IS 101 (Part 4/Sec 2)))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Dry Film Thickness per coat, min. a) By Brush (IS 101 (Part 3/Sec 2)-89 By Elecometer)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Volume Solid % min (Appendix-I))	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Scratch hardness, (Load 1000 g), clause 3 of (IS 101 (Part 5/Sec 2))-88)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flexibility and adhesion (6.25mm mandrel), (IS 101 (Part 5/Sec 2))-88)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flash Point (a) Component A (IS 101 (Part 1/Sec 6)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flash Point, (b) Component B (IS 101 (Part 1/Sec 6)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Resistance to salt spray, for 1000 hrs (IS 101 (Part 6/Sec 1)-88)	40000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Protection against corrosion under condition of condensation, for 1000 hrs (IS 101 (Part 6/Sec 1)-88)	30000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Keeping Properties for Pack A, 18 Months (IS 101 (Part 6/Sec 2)-89)	7000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Keeping Properties for Pack B, 18 Months (IS 101 (Part 6/Sec 2)-89)	7000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Mass in kg/10 liters, minimum (IS 101 (Part 1/Sec. 7)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Pot life a) at 27 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Pot life b) at 40 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Theoretical Spreading Capacity, min (with 10% Thinner), Appendix-I)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Fineness of grind, min (IS 101 (Part 3/Sec. 5)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Viscosity (Efflux time by ford cup No. 4 of paint i.e. mixture of two components at 27(+/-2 deg C) (with 10% Thinner))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Please Refer Annexure)	1.0
- (Resistance to Pull of adhesion test, (ASTM D 4541))	2000.0
- (Abrasion resistance test, 1.0 Kg Load, CS-17 Wheel, 1000 cycle (ASTM D 4060))	3000.0

322

RDSO SPECIFICATION No. M&C/PCN/129/2018 (2018) - SPECIFICATION FOR FULL GLOSS POLYSILOXANE BASED ENAMEL (TWO PACK)

SPECIFICATION FOR FULL GLOSS POLYSILOXANE BASED ENAMEL (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, h, Max : a) Surface dry (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, Max b) Hard dry (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, Max C) Hard dry at 70 Deg C (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Consistency (IS 101 (Part 1/Sec 5))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Colour (IS 101 (Part 4/Sec 2)))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Dry Film Thickness per coat, minimum (IS 101 (Part 3/Sec 2)-89 By Elcometer)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Volume Solid % min (Appendix-I))	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Scratch hardness, (Load 1.5 kg), clause 3 of (IS 101 (Part 5/Sec 2))-88)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flexibility and Adhesion (6.25 mm mandrel), (IS 101 (Part 5/Sec 2))-88)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flash Point a) Component A (IS 101 (Part 1/Sec 6)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flash Point Component B (IS 101 (Part 1/Sec 6)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Fineness of grind, Max (IS 101 (Part 3/Sec. 5)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Pot life a) at 27 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Pot life a) at 40 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Gloss value at 60 Deg angle of incidence, Minimum (IS 101 (Part 4/Sec 4)-88))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Mass in kg/10 liters, minimum (IS 101 (Part 1/Sec. 7)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Keeping Properties, 18 Months (Appendix-III))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Theoretical Spreading rate, min, Appendix-I)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix. Of two components at 27 (+/-2 Deg.C.) in supply condition (IS 101 (Part 1/Sec.5)))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests a) Resistance to 30% Sulphuric acid (wt by vol) for 24 hours (Appendix-V))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests b) Resistance to 20% caustic potash (wt by vol) for 24 hours (Appendix-V))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests c) Resistance to oil for 2 hours (Appendix-V))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests d) Resistance to Solvent for 3 hours (Appendix-V))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests e) Resistance to Water for 240 hours (Appendix-V))	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Durability Tests Accelerated Weathering test, for 1000 hours (Weather-o-meter, Xenon Arc Lamp) (Appendix-VI))	60000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Humidity Tests (on full system) for 4000 hrs (IS 101 (Part 6/Sec 1))	120000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (% Silicone on non-volatile binder basis, (min) (ASTM D 297 & Appendix-VIII)	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Abrasion resistance test with 1.0 kg load & CS-17 Wheels, 1000 cycles, (ASTM D 4060))	3000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Adhesion & Compatibility test on full system (ASTM D 3359 & Appendix-VII))	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Please refer annexure)	1.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Finish (IS 101 (Part 3/Sec 4) -1987))	1200.0
Appendix-VI Durability test (Durability tests Accelerated weathering test, 750 hrs (ASTM G 53, 4 hrs UV and 4 hrs condensation))	45000.0

323

RDSO SPECIFICATION No. M&C/PCN/129/2018 (2018) - Specification for Epoxy Based Micaceous Iron Oxide (Two-Pack) (Chapter-IV)

Specification for Epoxy Based Micaceous Iron Oxide (Two-Pack) (Chapter-IV)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.4 (Weight per Epoxy Equivalent on Non-volatile vehicle content basis (IS 9162-79))	3500.0
3.5a (Pigment content (3.5a) (IS 101 (Part 8/Sec. 2)-90)	2000.0
Table No. II (Drying time, h, Max : a) Surface dry (IS 101 (Part 3/Sec 1))-86)	1200.0
Table No. II (Drying time, Max b) Hard dry (IS 101 (Part 3/Sec 1))-86)	1200.0
Table No. II (Drying time, Max c) Hard dry at 70 Deg C (IS 101 (Part 3/Sec 1))-86)	1500.0
Table No. II (Consistency (IS 101 (Part 1/Sec 5)-89)	1200.0
Table No. II (Colour (IS 101 (Part 4/Sec 2)))	1200.0
Table No. II (Dry Film Thickness per coat, min. a) By Brush (IS 101 (Part 3/Sec 2)-89)	1200.0
Table No. II (Dry Film Thickness per coat, min. a) By airless spray (IS 101 (Part 3/Sec 2)-89)	1200.0
Table No. II (Volume Solid % min (Appendix-I))	2000.0
Table No. II (Scratch hardness, (Load 1.5 kg), (IS 101 (Part 5/Sec 2))-88)	1200.0
Table No. II (Flexibility and adhesion (IS 101 (Part 5/Sec 2))-88)	1200.0
Table No.II (Flash Point for both packs (IS 101 (Part 1/Sec 6)-87)	1200.0
Table No. II (Resistance to salt spray for 1000 hrs (IS 101 (Part 6/Sec 1)-88)	40000.0
Table No. II (Protection against corrosion under condition of condensation for 1000 hrs (IS 101 (Part 6/Sec 1)-88)	30000.0
Table No. II (Keeping Properties for Pack A, 18 Months (IS 101 (Part 6/Sec 2)-89)	7000.0
Table No. II (Keeping Properties for Pack B, 18 Months (IS 101 (Part 6/Sec 2)-89)	7000.0
Table No. II (Pot life a) at 27 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
Table No. II (Pot life a) at 40 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
Table No. II (Mass in kg/10 liters, minimum (IS 101 (Part 1/Sec. 7)-87)	1200.0
Table No. II (Theoretical Coverage, Minimum (Appendix-I))	1200.0
Table No. II (Adhesion and compatibility with primer and finish coat (ASTM D 3359-97 & Appendix-II))	2000.0
Table No. II (Fineness of grind, minimum (IS 101 (Part 1/Sec. 7)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Please refer Annexure)	1.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Finish (IS 101 (Part 3/Sec 4)-1987))	1200.0
3.5b (Pigment content: (3.5b))	2000.0

324

Customized specification for Hypertron Hybrid - Customized specification for Hypertron Hybrid

Customized specification for Hypertron Hybrid

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Acid-Alkali resistance (Immersed membranesTensile strength and Elongation test)-As per test method ASTM D 412)	6000.0
- (Hardness(Shore D) - As per test method ASTM D 2240)	1000.0
- (Hardness(Shore A) - As per test method ASTM D 2240)	1000.0
- (Elongation (As per test method ASTM D 412))	2000.0
- (Tensile strength (As per test method ASTM D 412))	2000.0
- (Tear Resistance (As per test method ASTM D 624))	4000.0
- (Taber abrasion(As per test method ASTM D 4060))	3000.0
- (Water permeability of coating(As per test method ASTM E 96))	5000.0
- (Salt spray test-100 hours (As per test method ASTM B 117))	4000.0
- (Impact test (As per test method ASTM D 2794))	1500.0

325

IS 14768 : Part 2 (2003) - Conduit fittings for electrical installations - Specification: Part 1 general requirements

Conduit fittings for electrical installations - Specification: Part 1 general requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Construction of Conduit Fitting for Electrical Installations)	2000.0
10.3 (Impact Test as per IS 14768 Part1 Cl.10.3)	2000.0
10 (Suspended Load Test as per IS 14768 Part 1, Cl. 10.2)	2000.0
8 (Dimension of Conduit Fittings for Electrical Installations as per IS 14768 Part 1 Cl.8)	2000.0

326

Customized specification for News print paper - Customized specification for News print paper

Customized specification for News print paper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Grammage (as per IS 1060 (Part 5/Sec 5)))	1000.0
- (Brightness (as per IS 1060 (Part 4/Sec 13) ))	2000.0
- (Smoothness(as per IS 1060 (Part 5/Sec 20))	2000.0

327

IS 9537 : Part 2 (1981) - Specification for conduits for electrical installations: Part 2 rigid steel conduits

Specification for conduits for electrical installations: Part 2 rigid steel conduits

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2 (Bend Test)	1000.0
9.3 (Compression Test)	3000.0
7 (Wall thickness)	500.0
7 (Outside Diameter)	500.0
13 (External InfulanceTest)	2000.0

328

NTH(WR)/MECH/CUSTOM/006 (2023) - Hot rolled and Cold reduced Steel Sheets and Strips - Galvanized/ Galvannealed/ Electrogalvanized

Hot rolled and Cold reduced Steel Sheets and Strips - Galvanized/ Galvannealed/ Electrogalvanized

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Chemical Compositions as per IS 513 Part 1/IS 513 Part 2 / IS 1079 /IS 5986/ IS 277 /IS 17404/ ASTM A653 or any other relevant Standard Spec.)	7000.0
2.0 (Mass of Coating/ Triple Spot Coating Test as per IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec.)	2000.0
3 (Freedom From Defects - Visual Examination as per IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec.)	1000.0
4 (Dimension Measurements as per IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec.)	1000.0
5.1 (Tensile Test as per IS 1079/IS 513 Part-1/IS 513 Part-2/ IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec. and Test Method IS 1608 /ASTM E8)	1000.0
5.2 (Yield /0.2% Proof Stress as per IS 1079/IS 513 Part-1/IS 513 Part-2/ IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec. and Test Method IS 1608 /ASTM E8)	1000.0
5.3 (% of Elongation as per IS 1079/IS 513 Part-1/IS 513 Part-2/ IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec. and Test Method IS 1608 /ASTM E8)	1000.0
6 (Bend Test as per IS 1079/IS 513 Part-1/IS 513 Part-2/ IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec. and referred test method)	1000.0
7 (Cupping Test as per IS 10175)	2000.0
8 (Hardness - Rockwell/Brinell/ Vickers as per IS 1586 Part-1/ IS1500 Part-1/ IS 1501 Part-1)	2000.0
2.1 (Nature of Coating /% of Coating Elements by AAS Method as per ISO 17925 or any other relevant method.)	2400.0

329

IS 1899 (1977) - Specification for blow lamps (Second Revision)

Specification for blow lamps (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3,6,7,8 and 11 (Blow Lamp Type and Size, Design and Dimension, Construction, Finish, Marking and Tests as per the clauses 3,6,7,8 and 11)	14000.0

330

Customized Specification for Weights and Measures(Wajan and Parimane) - Customized Specification for Weights and Measures(Wajan and Parimane)

Customized Specification for Weights and Measures(Wajan and Parimane)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Availability of Standard Weights (1g to 100g ))	3000.0