NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum[at]nth[dot]gov[dot]in

Scope List

Reset

805 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

391

IS 1848(Part 1):2018 and IS 1848 - Cream wove and Cream laid paper

Cream wove and Cream laid paper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Dimensions (cm.))	1000.0
- (Brightness(%))	2000.0
- (One Minute Cobb(Average Max.))	2000.0
- (Breaking Length/Tensile Strength(Cross Direction))	1000.0
- (Breaking Length/Tensile Strength(Machine Direction))	1000.0
- (Opacity(%))	2000.0
- (Tear Index(CD))	2000.0
- (Tear Index(MD))	2000.0
- (Resistance to feathering)	1000.0
- (Weight/Grammage(g/sq.m.))	1000.0

392

IS 4658:2019 - Specification for Coated Paper and Coated Board(Art and Chromo)

Specification for Coated Paper and Coated Board(Art and Chromo)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Weight/Grammage(gm./sq.m))	1000.0
- (Burst Index (kpa.m2/g))	1000.0
- (Wax Pick)	2000.0
- (Gloss(%))	1500.0
- (Brightness(%))	2000.0
- (Surface pH)	1000.0
- (Dimensions(cm.))	1000.0

393

IS 17876 (2022) - Stainless Steel Welded Pipes and Tubes for General Services - Specification

Stainless Steel Welded Pipes and Tubes for General Services - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 (Tensile Requirement - Tensile Strength as per IS 1608 Part 1 or Test Method specified)	1000.0
10.1 (Tensile Requirement - Yield Strength as per IS 1608 Part 1 or Test Method specified)	1000.0
10.1 (Tensile Requirement - %Percentage of Elongation (on Gauge Length of 50mm) as per IS 1608 Part 1 or Test Method specified)	1000.0
12 (Hardness Test - Rockwell Hardness as per IS 1586 Part 1 / Brinell Hardness as per IS 1500 Part 1 or other Test Method Specified)	2000.0
11 (Transverse Tension Test as per IS 1608 Part 1)	3000.0
13 (Flange Test as per IS 2330 or relevant Test Method Specified)	1500.0
14 (Reverse Flattening Test as per IS 17876 or specified Test Method)	1000.0
15 (Flattening Test as per IS 2338 or relevant Test Method Specified)	1000.0
16 (Grain Size determined as per IS 4748 or relevant test method specified)	3500.0
18 (Leak Tightness Test by Hydrostatic Test as IS 17876 or relevant test method specified)	2500.0
19 (Corrosion Resistance as per IS 10461 Part 1 or IS 10461 Part2 or relevant test method specified)	10000.0
22 (Workmanship, Finish, and Appearance- Visual Examination as per IS 17876 or relevant Test Method Specified)	1000.0
23 (Repair by Welding or Grinding - Visual Examination as per IS 17876 or relevant Test Method Specified)	1000.0
24 (Dimension Measurement as per IS 17876 or relevant test method Specified)	1000.0
25 (Marking - Visual Examination as per IS 17876)	1000.0
8 (Chemical Composition - Ladle Analysis as per IS 228 and its relevant parts or any other established instrumental/chemical method)	5000.0
Clauses 8.1 and 8.2 (Carbon (as C))	1000.0
Clauses 8.1 and 8.2 (Silicon (as Si))	1000.0
Clauses 8.1 and 8.2 (Manganese (as Mn))	1000.0
Clauses 8.1 and 8.2 (Nickel (as Ni))	1000.0
Clauses 8.1 and 8.2 (Chromium (as Cr))	1000.0
Clauses 8.1 and 8.2 (Molybdenum (as Mo))	1000.0
Clauses 8.1 and 8.2 (Sulphur (as S))	1000.0
Clauses 8.1 and 8.2 (Phosphorus (as P))	1000.0

394

IS 104 (2017) - Ready Mixed Paint, Brushing, Zinc Chrome, Priming

Ready Mixed Paint, Brushing, Zinc Chrome, Priming

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
i) Table 1 Cl 4.3&7.1 (Consistency)	100.0
ii) Table 1 Cl 4.3&7.1 (Finish)	100.0
iii) Table 1 Cl 4.3&7.1 (Drying time-Hard dry in hours)	100.0
iv) Table 1 Cl 4.3&7.1 (Mass, kg/10 liter)	100.0
v) Table 1 Cl 4.3&7.1 (colour)	100.0
vi) Table 1 Cl 4.3&7.1 (Wet opacity, m2/10 liter)	100.0
vii.a) Table 1 Cl 4.3&7.1 (Flexibility and adhesion a. Scratch hardness (Load 1 000 g))	100.0
vii.b) Table 1 Cl 4.3&7.1 (Flexibility and adhesion b) Bend test, with 6.25 mm dia mandrel and type 1 apparatus)	100.0
viii) Table 1 Cl 4.3&7.1 (Flash point)	200.0
ix.a) Table 1 Cl 4.3&7.1 (Resistance to humidity Under conditions of condensation a)Resistance to humidity)	2000.0
ix.b) Table 1 Cl 4.3&7.1 (Resistance to humidity Under conditions of condensation b)Resistance to salt spray)	2000.0
Cl 4.1 (Pigment content, percent by mass (IS:101 part 8/sec 2:1990))	1000.0
x) Table 1 Cl 4.3&7.1 (Keeping properties)	5000.0
Cl 4.1.1 ANNEX B (Chromic anhydride(CrO3) content, percent by mass)	2000.0
Cl 4.1.1 ANNEX B (Zinc oxide(ZnO) content, percent by mass)	2000.0
Cl 4 (Zinc chrome content, percent by mass ( including Chromic anhydride & Zinc Oxide))	100.0
Cl 4 (Lead Restriction)	2000.0

395

IS 2185 (2005) - Hollow and Solid Concrete Blocks.

Hollow and Solid Concrete Blocks.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.4 (Compressive Strength of Blocks, in N/mm^2 (a) Uncoated/untreated Specimens (b) Coated / Treated Specimens)	8000.0
9.5 (Water Absorption of Blocks, in % (a) Uncoated/untreated Specimens (b) Coated / Treated Specimens)	2000.0

396

IS 1077 (1992) - Common Burn Clay Building Brick [Not Scheduled]

Common Burn Clay Building Brick

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Crushing Strength (Compressive Strength) of Bricks, in N/mm^2 (a) Uncoated/untreated Specimens (b) Coated / Treated Specimens)	4000.0
7.2 (Water Absorption of Bricks, in % (a) Uncoated/untreated Specimens (b) Coated / Treated Specimens)	3000.0
7.3 (Efflorescence Test of Bricks (a) Uncoated/untreated Specimens (b) Coated / Treated Specimens)	3000.0

397

- - PP Sheet 8mm. Thick

PP Sheet 8mm. Thick

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Thickness of Sheet(mm.))	1000.0
- (Tensile Strength @Yield as per ISO 527)	2000.0
- (Elongation @Yield as per ISO 527)	1.0
- (Elongation @Break as per ISO 527)	1000.0
- (Density as per ISO 1183)	1000.0
- (Melt Flow rate as per ISO 1133)	2000.0
- (Shore A Hardness as per ASTM D 2240)	2000.0

398

None - UPVC Window shutter section

UPVC Window shutter section

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Vicat Softening Temperature as per ISO 306(Deg. C))	2000.0
- (Charpy Impact test as per ASTM D 6110 (KJ/sq.m))	2000.0
- (Flexural Modulus Elasticity as per ISO 178 (N/sq.mm.))	3000.0
- (Heat Reversion Test as per IS 12235(Part 5/Sec 1):2004(%))	2000.0
- (Tensile Strength as per ISO 527(MPa))	2000.0

399

ASTM D 6083 - Liquid applied acrylic coatings used in roofing

Liquid applied acrylic coatings used in roofing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Initial % Elongation as per ASTM D 2370)	3000.0
- (Initial Tensile Strength(max. Stress in MPa) as per ASTM D 2370)	3000.0
- (Tear Resistance(kN/m) as per ASTM D 624)	2000.0
- (Hardness as per ASTM D 2240(Shore A))	1000.0
- (Water Swelling as per ASTM D 471(max. %))	2000.0
- (Final % Elongation (break)after accelerated weathering 1000 h as per ASTM D 4798 and ASTM D 2370)	63000.0

400

Navigation Light - Navigation Light

Navigation Light

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

401

IS 4163 (2021) - Steel - Determination of content of nonmetallic inclusions - Micrographic method using standard diagrams

Steel - Determination of content of nonmetallic inclusions - Micrographic method using standard diagrams

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Inclusion rating)	4000.0

402

IS 1757 Part 1 (2020) - Metallic Materials — Charpy Pendulum Impact Test Part 1 Test Method ( Fourth Revision )

Metallic Materials — Charpy Pendulum Impact Test Part 1 Test Method ( Fourth Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Impact Test with sample preparation)	5000.0
9 (Impact Test without sample preparation)	4000.0

403

IS 1755:2018 (2018) - Metallic Materials - Wire - Wrapping test

Metallic Materials - Wire - Wrapping test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Metallic Materials - Wire -Wrapping test)	1000.0

404

IS 1717 : 2018 (2018) - Metallic Materials - Wire - Simple Torsion Test (Fourth Revision)

Metallic Materials - Wire - Simple Torsion Test (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Metallic Materials - Simple Torsion Test-Wire ( Number of Turns))	1000.0
Annex B (Evaluation of Fracture Occurring during Simple Torsion Test - Visual)	1000.0

405

FCO 1985 (Annexure) - FCO-1985 (Annexure)

FCO-1985 (Annexure)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1 to 3 test parameters)	2000.0
2 (4 to 6 parameters (Vide Annexure))	4000.0
3 (7 or more parameters (Vide annexure))	7000.0

406

IS 14255:1995 - Aerial bunched Cables

Aerial bunched Cables

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1.a.i (Tests on phase/street light conductor - Tensile Test)	3000.0
10.1.a.ii (Tests on phase/street light conductor - Wrapping Test)	1000.0
10.1.a.iii (Tests on phase/street light conductor - Resistance Test)	5000.0
10.1.b.i (Test on messenger conductor - Breaking Load)	1500.0
10.1.b.ii (Test on messenger conductor - Elongation Test)	1500.0
10.1.b.iii (Test on messenger conductor - Resistance Test)	5000.0
10.1.f (Insulation resistance (Volume resistivity) test)	5000.0
10.1.g (High voltage test)	5000.0
10.1.c.i & ii (Physical tests for XLPE insulation - Tensile strength and elongation at break (before and after ageing))	5000.0
10.1.c.iii (Physical tests for XLPE insulation - Hot set Test)	2000.0
10.1.c.iv (Physical tests for XLPE insulation - Shrinkage Test)	2000.0
10.1.c.v (Physical tests for XLPE insulation - Water absorption (Gravimetric))	2000.0
10.1.c.vi (Physical tests for XLPE insulation - Carbon black dispersion)	1000.0
10.1.d.v (Physical tests for PE insulation - Environmental stress cracking)	3000.0

407

IS 14255 (1995) - Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 ()	-

408

IS 9894:1981 RA:2018 - Method of Test for Smoothness/Roughness of Paper

Method of Test for Smoothness/Roughness of Paper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Smoothness of Paper (ml./min.))	2000.0

409

- - Non Woven Polyester Reinforced With Mineral Finish

Non Woven Polyester Reinforced With Mineral Finish

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength (Length wise)-N/5 cm. as per ASTM D 5147)	1000.0
- (Tensile Strength (Cross wise)-N/5 cm. as per ASTM D 5147)	1000.0
- (Elongation (Length wise)-% as per ASTM D 5147)	1000.0
- (Elongation (Cross wise)-% as per ASTM D 5147)	1000.0
- (Tear Resistance(Lengthwise)-N, as per ASTM D 5147)	1000.0
- (Tear Resistance(Cross wise)-N, as per ASTM D 5147)	1000.0
- (Pressure Head Test as per IS 13826(Part 4))	2000.0
- (Cold Flexibility as per ASTM D 5147)	2000.0
- (Heat Resistance at 120°C as per ASTM D 5147)	2000.0
- (Thickness (mm.) as per EN 1849)	1000.0
- (Length (mm.)as per EN 1849)	1000.0
- (Softening Point(°c)as per ASTM D 36)	2000.0

410

IS 15965: 2012 - Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3 (Adhesion Test)	1000.0
11.1 (Total Coated Thickness)	1000.0
6 (Tensile strength)	2000.0
6 (Yield stress)	1000.0
6 (Elongation)	1000.0
6 (Mass of AZ Coating)	2000.0
7.3 (Top Coat)	1000.0
7.3 (Bottom Coat)	1000.0
0 (Chemical composition, % by mass)	2500.0
1 (Thickness of AZ Coating)	2000.0
0 (Total coated thickness(TCT), mm)	1000.0
11 (Pitch of Corrugation, mm)	1000.0
11 (Depth of Corrugation, mm)	1000.0
0 (Composition of AZ Coating Material)	3000.0

411

IS 15961 :2025 (2025) - Hot Dip Aluminium-Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)- Specification

Hot Dip Aluminium-Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)- Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Thickness of Sheet (base metal thickness), mm)	1000.0
3.3 (Coated thickness (total coated thickness), mm)	1000.0
9.1 (Mass of coating (Both sides), g/Sq m)	2000.0
7.1 (Carbon. percent)	500.0
7.1 (Manganese, percent)	500.0
7.1 (Sulphur, percent)	500.0
7.1 (Phosphorous, percent)	500.0
8.3 (Tensile Strength)	1000.0
8.3 (Percent Elongation)	1000.0
8.3 (Yield Strength)	1000.0

412

IS 10322 : Part 5 : Sec 1 (2012) - Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Provision for earthing)	1200.0
12 (Protection against Electric Shock)	1200.0

413

IS 6745 (1972) - Mass of Zinc Coating (IS 6745)

Mass of Zinc Coating (IS 6745)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Mass of Zinc Coating,(IS 6745:1972))	2000.0

414

IS 16098(Part 2) - STRUCTURED-WALL PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE

STRUCTURED-WALL PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Outer Diameter(mm.))	1000.0
- (Inner Diameter(mm.))	1000.0
- (Wall Thickness(mm.))	1000.0
- (Impact Test)	2000.0
- (Resistance to heating oven test)	2000.0
- (Ring Flexibility)	2000.0

415

IS 1367 : Part 14 : Sec 3 : 2018 (2018) - Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion-resistant Stainless-steel Fasteners Section 3 Set Screws and Similar Fasteners not Under Tensile Stress (Fourth Revision)

Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion-resistant Stainless-steel Fasteners Section 3 Set Screws and Similar Fasteners not Under Tensile Stress (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Visual Observations of Designation, Marking and Finish)	1000.0
5.2 (Hardness Test in Vickers/ Brinell/Rockwell as per the relevant IS spec.)	2000.0
4 (Chemical compositions (in % )of stainless steels suitable for fasteners in accordance with this part of ISO 3506 are given in table 2.)	5000.0

416

IS 1367 : Part 6 (2018) - Technical Supply Conditions for Threaded Steel Fasteners Part 6 Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel — Nuts with Specified Property Classes — Coarse Thread and Fine Pitch Thread

Technical Supply Conditions for Threaded Steel Fasteners Part 6 Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel — Nuts with Specified Property Classes — Coarse Thread and Fine Pitch Thread

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Chemical composition, % by mass)	2500.0

417

IS 1367 : Part 3 (2017) - Technical Supply Conditions for Threaded Steel Fasteners Part 3 Mechanical Properties of Fasteners Made of Carbon Steel and Bolts, Screws and Studs

Technical Supply Conditions for Threaded Steel Fasteners Part 3 Mechanical Properties of Fasteners Made of Carbon Steel and Bolts, Screws and Studs

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Chemical Composition, % by mass)	2500.0
7 (Surface Integrity (Table 3 in accordance with ISO 6157 - 1 ))	1200.0
7 (Mechanical and physical properties (tensile Strength))	3.0
7 (Mechanical and physical properties (ultimate tensile load))	3000.0
7 (Mechanical and physical properties (Proof load test))	2000.0
7 (Mechanical and physical properties (Hardness,Rockwell C scale))	2000.0
7 (Mechanical and physical properties (Hardness,Vickers))	2000.0

418

IS 1367 : Part 6 (2018) - Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Surface Integrity)	1200.0
7 (Hardness Test)	2000.0
7 (Proof Load)	3000.0
7, Table 6 (Rockwell hardness, HRC)	2000.0
6 (Chemical composition, % by mass)	2500.0

419

IS 1367 : Part 3 (2017) - Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Surface Integrity)	1200.0
7 (Hardness Test)	2000.0
7 (Wedge loading test)	3000.0
7 (Proof Load, N.)	3000.0
7 (Tensile load, N.)	3000.0
2 (Dimensions)	1500.0
6 (Carbon, % by mass)	500.0
6 (Phosphorus, % by mass)	500.0
6 (Sulphur, % by mass)	500.0
6 (Boron, % by mass)	625.0

420

IS 1367 : Part 13 (2020) - Technical Supply Conditions for Threaded Steel Fasteners Part 13 Hot Dip Galvanized Coatings on Threaded Fasteners ( Third Revision )

Technical Supply Conditions for Threaded Steel Fasteners Part 13 Hot Dip Galvanized Coatings on Threaded Fasteners ( Third Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3 (Coating Thickness)	2000.0