NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum@nth.gov.in

Scope List

Reset

734 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

361

IS 1285 (2023) - Wrought Aluminium and Aluminium Alloys — Extruded Round Tube and Hollow Sections for General Engineering Purposes

Wrought Aluminium and Aluminium Alloys — Extruded Round Tube and Hollow Sections for General Engineering Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Chemical Analysis (as per IS 733))	5000.0
10 (Tensile Strength (as per IS 733))	1000.0
10 (0.2 % Proof Stress (as per IS 733))	1000.0
10 (% Elongation (as per IS 733))	1000.0
8 (Dimension)	1000.0
4 (Mass per meter)	1000.0
6 (Freedom from Defect)	1000.0
8 (Copper, % by mass)	600.0
8 (Magnesium, % by mass)	600.0
8 (Silicon, % by mass)	600.0
8 (Iron, % by mass)	600.0
8 (Manganese, % by mass)	600.0
8 (Zinc, % by mass)	600.0
8 (Titanium, % by mass)	600.0
8 (Others, % by mass)	600.0
8 (Chromium, % by mass)	600.0
8 (Aluminium, % by mass)	600.0
4 (Dry Film Thickness - Powder Coating as per IS 13871 by Test Method 5 of IS 101 Part-3 Sec.2 1989 or any other test method specified by the customer)	1500.0

362

IS 2086 (1993) - Carriers and bases in rewirable type electric fuses for voltages up to 650 v - Specification (Third Revision)

Carriers and bases in rewirable type electric fuses for voltages up to 650 v - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

363

Custom - Berger QUV test - QUV test of Paint and Coating

QUV test of Paint and Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A-2 (Salt spry for 96 hrs)	5000.0

364

IS 2086 (1993) - Carriers and Bases in Electrical Fuses for voltages up to 650 V - Specification

Carriers and Bases in Electrical Fuses for voltages up to 650 V - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (All possible tests as per customer requirement)	20000.0

365

IS 9968 : Part 1 (1984) - Elastomer Insulated Cables

Elastomer Insulated Cables

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.2 (Conductor Resistance)	2000.0
21.1 (Insulation resistance)	1000.0
22.1 (High voltage (water immersion) test)	1000.0
22.1 (Flammability test)	1000.0

366

IS 3384 (1986) - bitumen primer for use in waterproofing and damp-proofing

bitumen primer for use in waterproofing and damp-proofing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1(v)c (Test on residue from distillation upto 360 dg , c)matter soluble in carbon disulphide or ccl4 or tce)	1200.0
3.1(v)b (Test on residue from distillation upto 360 dg , b)penetration 25 dg 100g 5 sec)	1200.0
3.1(v) a (Test on residue from distillation upto 360 dg , a)ductility)	1200.0
3.1(iv) (water Content )	1200.0
3.1(iii) (Flash point pensky martens closed type)	1200.0
ADDITIONAL pARAMETER (Specific gravity)	1200.0

367

IS 7193:2013 - Glass Fibre Base Bitumen Felts

Glass Fibre Base Bitumen Felts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 Table 3(Sl.no. i) (Breaking Load(warp direction) as per IS 13826(Part 1))	2000.0
8 Table 3(Sl.no. i) (Breaking Load(weft direction) as per IS 13826(Part 1))	2000.0
8 Table 3(Sl.no. ii) (Pliability at 23 ±1°C as per IS 13826(Part 2))	2000.0
8 Table 3(Sl.no. iii) (Storage Sticking as per IS 13826(Part 3))	2000.0
8 Table 3(Sl.no. iv) (Pressure Head test(conditioned at 5°C) as per IS 13826(Part 4))	2000.0
8 Table 3(Sl.no. iv) (Pressure Head test(conditioned at 65°C) as per IS 13826(Part 4))	2000.0
8 Table 3(Sl.no. v) (Heat resistance at 68±2°C as per IS 13826(Part 5))	2000.0
8 Table 3(Sl.no. vi) (Water absorption percent as per IS 13826(Part 6))	2000.0
7.1 (Dimensions(Length and Width))	1000.0
7.2 (Weight)	1000.0

368

IS 1254 (2007) - Corrugated aluminium sheet (Fourth Revision)

Corrugated aluminium sheet (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Aluminium)	500.0
7 (Dimension)	1000.0

369

IS 737 (2008) - Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes - Specification (Fourth Revision)

Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Chemical Analysis (Please see Annexure)- NABL)	6000.0
7.2 (Bend Test)	1000.0
7.1 (% Elongation at 50 mm gauge length)	500.0
7.1 (0.2% Proof Stress)	1000.0
7.1 (Tensile Strength)	1000.0
9 (Dimensions)	1000.0
6 (Chemical Analysis (Please see Annexure)- NABL)	6000.0
6 (Titanium)	1000.0
6 (Silicon)	1000.0
6 (Manganese)	1000.0
6 (Chromium)	1000.0
6 (Magnesium)	1000.0
6 (Iron)	1000.0
6 (Copper)	1000.0
6 (Zinc)	1000.0
6 (Aluminium)	1000.0
6 (Chemical composition, Cu+Si+Fe for designation 19990.)	1000.0
6 (Chemical composition, Cu+Si+Fe+Mn+Zn for Designation 19800)	1000.0
6,Table1 (Chemical Composition (Please see Annexure) - NON NABL)	2500.0
6 (Chemical composition, Cr+Mn for Designation 55000)	2500.0

370

IS 2553 : PART 1 (1990) - SAFETY GLASS PART 1 ARCHITECTURAL, BUILDING AND GENERAL USES

SAFETY GLASS PART 1 ARCHITECTURAL, BUILDING AND GENERAL USES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

371

IS 2553(1):2018 & IS 17004:2018 (2018) - SAFETY GLASS — SPECIFICATION PART 1 ARCHITECTURAL, BUILDING AND GENERAL USES & TESTING METHODS FOR PROCESSED GLASS

SAFETY GLASS — SPECIFICATION PART 1 ARCHITECTURAL, BUILDING AND GENERAL USES & TESTING METHODS FOR PROCESSED GLASS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

372

Fibre Glass Insulation - Fibre Glass Insulation

Fibre Glass Insulation

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Thickness(mm.))	1000.0

373

Nitrile Rubber - Nitrile Rubber

Nitrile Rubber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's requirement (Thickness)	1000.0

374

IS 14589 (1999) - ZINC PRIMING PAINT, EPOXY BASED, (TWO-PACK) -SPECIFICATION

ZINC PRIMING PAINT, EPOXY BASED, (TWO-PACK) -SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ZINC PRIMING PAINT, EPOXY BASED, TWO-PACK - SPECIFICATION (Please refer annexure for tests result)	23000.0

375

IS 14209 (2016) - Epoxy Enamel, Two Component, Glossy — Specification

Epoxy Enamel, Two Component, Glossy — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Epoxy Enamel, Two Component, Glossy — Specification (Please refer annexure for tests result)	30000.0

376

IS 13213 (2018) - Polyurethane Full Gloss Enamel (Two Pack) — Specification

Polyurethane Full Gloss Enamel (Two Pack) — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Polyurethane Full Gloss Enamel (Two Pack) — Specification (Please refer annexure for tests result)	46000.0

377

IS 13238 (2021) - Epoxy Based Zinc Phosphate Primer (Two Pack ) — Specification

Epoxy Based Zinc Phosphate Primer (Two Pack ) — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Epoxy Based Zinc Phosphate Primer (Two Pack) — Specification (Please refer annexure for tests result)	23000.0

378

IS 13183 (1991) - ALUMINIUM PAINT, HEAT RESISTANT SPECIFICATION

ALUMINIUM PAINT, HEAT RESISTANT SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ALUMINIUM PAINT, HEAT RESISTANT — SPECIFICATION (Please refer annexure for tests result)	8000.0

379

TEC/GR/FA/CDS-008/AUG-19 - Permanently lubricated HDPE Telecom Duct

Permanently lubricated HDPE Telecom Duct

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength(N/sq.mm.) as per ASTM D 638)	2000.0
- (Elongation(%) as per ASTM D 638)	2000.0
- (Longitudinal reversion test(%)as per IS 4984)	2000.0
- (Impact Strength as per IS 12235(Part 9))	2000.0
- (Crush resistance)	3000.0

380

IRC SP 80-2008 (2008) - Guidelines for Corrosion Prevention

Guidelines for Corrosion Prevention

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Guidelines for corrosion prevention (Specific Gravity)	1200.0
Guidelines for corrosion prevention (Solid Contents)	1500.0
Guidelines for corrosion prevention (IR Spectrum (FTIR))	2000.0
Guidelines for corrosion prevention (Adhesion with concrete (ASTM D 4541))	10000.0
Guidelines for corrosion prevention (Dry Film Thickness (for minimum 2 coats))	1200.0
Guidelines for corrosion prevention (Coverage (2 coats))	1200.0
Guidelines for corrosion prevention (Water proofing characteristics (DIN 1048/ISO 12290))	10000.0
Guidelines for corrosion prevention (Re-coatability)	1200.0
Guidelines for corrosion prevention (Water Vapour Transmission (ASTM D 1653))	5000.0
Guidelines for corrosion prevention ((%) Elongation (ASTM D 2370))	2000.0
Guidelines for corrosion prevention (Tensile strength (ASTM D 2370))	2000.0
IRC SP 80 (UV Accelerated Weathering Test (ASTM G 53) 400 hrs)	24000.0

381

IS 15769 (2008) - Flux Cored (Tubular) Electrodes for Gas Shielded and Self Shielded Metal welding of Carbon or Carbon Manganese Steel

Flux Cored (Tubular) Electrodes for Gas Shielded and Self Shielded Metal welding of Carbon or Carbon Manganese Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Diameter of Core Wire)	500.0
4.2 (Temper)	1000.0
4.2 (Cast)	500.0
4.2 (Helix)	500.0
4.3 (Uniformity)	500.0
4.4.2 (Coils with Former, Overall Diameter, A)	500.0
4.4.2 (Coils with Former, Width, B)	500.0
4.4.2 (Coils with Former, Inner Diameter, C)	500.0
4.4.2 (Coils with Former, Inner Diameter, C, Max)	500.0
4.4.3 (Spools, Overall Diameter A)	500.0
4.4.3 (Spools, Overall Width, B)	500.0
4.4.3 (Spools, Inner Diameter, C)	500.0
4.4.3 (Spools, Distance Between Axes D)	500.0
4.4.3 (Spools, Driving Hole Diameter E)	500.0
4.4.3 (Spools, Weight, Max)	500.0
5.8 (Chemical Analysis)	5000.0
5.2 (Radiographic Examination)	1500.0
5.3 (Tensile Test)	3000.0
5.4 (Charpy Impact Test)	3000.0
5.1.3.2 (Dimension of Fillet Weld)	500.0
5.1.3.2 (Fillet Weld Fracture)	4000.0
5.5 (Transverse Tensile Test)	3000.0
5.6 (Longitudinal Guided Bend Test)	1000.0
5.7 (Diffusible Hydrogen Test)	5000.0

382

Customized Specification for Struct Guard Carbon Sheet - Customized Specification for Struct Guard Carbon Sheet

Customized Specification for Struct Guard Carbon Sheet

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength(N/sq.mm.) as per ASTM D 3039)	2000.0
- (Tensile Modulus(N/sq.mm) as per ASTM D 3039)	2000.0
- (Elongation(%) as per ASTM D 3039)	2000.0

383

NTH/WR/ME(CAL)/SOP/07 - Calibration of Measuring Tape

Calibration of Measuring Tape

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Linear Measurment of Measuring Tape (up to 1 meter))	1200.0
2 (Linear Measurment of Measuring Tape (up to 3 meter))	2000.0
3 (Linear Measurment of Measuring Tape (up to 5 meter))	2500.0
4 (Linear Measurment of Measuring Tape (up to 15 meter))	3500.0
5 (Linear Measurment of Measuring Tape (up to 50 meter))	5000.0

384

NTH/WR/ME(CAL)/SOP/06 (2023) - Calibration of Measuring Steel Scale (0-1000mm)

Calibration of Measuring Steel Scale (0-1000mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Linear Measurment of Steel Scale (0-300mm))	1200.0
2 (Linear Measurment of Steel Scale (0-600mm))	1200.0
3 (Linear Measurment of Steel Scale (0-1000mm))	1200.0

385

NTH/WR/ME(CAL)/SOP/05 (2023) - Calibration of Direct Pressure Indicating Device

Calibration of Direct Pressure Indicating Device

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Calibration of Direct Pressure Indicating device/Master Pressure Gauge (Range 1 to 690) bar by Comparison Method)	3000.0

386

NTH/WR/ME(CAL)/SOP/04 (2023) - Verification of UTM/Tension/Compression Testing Machine

Verification of UTM/Tension/Compression Testing Machine

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Calibration of UTM in Tension Mode up to 50kN (1 Scale))	6000.0
2 (Calibration of UTM in Compression Mode up to 500kN (1 Scale))	7000.0

387

NTH/WR/ME(CAL)/SOP/01 (2023) - Calibration of External Micrometer

Calibration of External Micrometer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Calibration of External Micrometer (up to 25mm))	1200.0

388

NTH/WR/ME(CAL)/SOP /03 (2023) - Calibration of Test Sieves for Wire Cloth Test Sieves and Perforated Plate Test Sieves

Calibration of Test Sieves for Wire Cloth Test Sieves and Perforated Plate Test Sieves

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test Sieves ( Aperture Size By Comparison Method - Tool Maker Microscope))	2000.0
2 (Test Sieves ( Aperture Size By Comparison Method - Vernier Caliper))	2000.0

389

NTH/WR/ME(CAL)/SOP /02 (2023) - Calibration of Vernier Caliper/Digital Caliper

Calibration of Vernier Caliper/Digital Caliper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension - Length ( Range 0-300mm))	1200.0
2 (Dimension - Length ( Range 0-600mm))	2000.0
3 (Dimension-Length ( Range 0-1000mm))	2000.0

390

IS 16491 : Part 1 (2024) - Geometrical product specifications (GPS) - Dimensional measuring equipment: Part 1 calipers; design and metrological characteristics

Geometrical product specifications (GPS) - Dimensional measuring equipment: Part 1 calipers; design and metrological characteristics

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Length)	1200.0
5 (Length)	2000.0
5 (Length)	2000.0
5 (Length)	2000.0