NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb@nic.in

Scope List

Reset

1093 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

901

LP -01 (Emergency Light) - Testing of LED Emergency Light

Testing of LED Emergency Light

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Total Luminous Flux (lm))	5000.0

902

IS 5493 (1981) - Dimensions for wrought copper and copper alloy tubes (First Revision)

Dimensions for wrought copper and copper alloy tubes (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.1 (Out Side Diameter)	1000.0
2.2 (Thickness)	1000.0
2.3 (Roundness)	1000.0

903

ICAO Annex 14 - On the lines of ICAO annexure 14(test for aviation obstruction light)

On the lines of ICAO annexure 14(test for aviation obstruction light)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Peak Intensity (cd) in single-mode (non flashing mode))	10000.0
A.2 (Peak Intensity (cd) in dual mode (non flashing mode ))	20000.0

904

IS-9537(Part-II)-1981 Reaff. 2017 - Conduits for Electrical Installations- Rigid Steel Conduits

Conduits for Electrical Installations- Rigid Steel Conduits

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Classification)	2000.0
6 (Marking)	1000.0
7 (Dimensions)	2000.0
9.2 (As per Specification)	5000.0
9.3 (Compression Test as specification)	5000.0
8 (Smoothness of inside and outside surface of Conduit)	3000.0

905

1000 (0) - Cement Content w.r.t Sand

Cement Content w.r.t Sand

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1000.1 (Cement Content w.r.t Sand)	5000.0

906

IS 456-II (2000) - Plain and Reinforced Concrete - CONCRETE CHEMICAL

Plain and Reinforced Concrete - CONCRETE CHEMICAL

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.4.1.2 (Compressive strength of water sample)	4000.0
5.4.1.3 (Setting time of water sample)	2000.0

907

On the lines of ICAO Annexure 14 - Aviation Obstruction Light

Aviation Obstruction Light

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Light Intensity ( cd))	10000.0
2 (Degree of Protection IP-6X ( Dust Tight) as per IS/IEC 60529)	6000.0
3 (Degree of Protection IP-X5 ( Protection against Water Jet as per IS/IEC 60529))	6000.0

908

IS 516 : Part 1 : Sec 1 (2021) - Hardened concrete methods of test part 1 testing of strength of hardened concrete section 1 compressive,flexucal and split tensile strength (First Revision)

Hardened concrete methods of test part 1 testing of strength of hardened concrete section 1 compressive,flexucal and split tensile strength (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Compressive Strength of CC Cube 1 set IS 516 (Part1)/Sec1:2021)	1200.0

909

IS 9000 : Part 8 (1981) - Basic environmental testing procedures for electronic and electrical items: Part 8 vibration (Sinusoidal) test

Basic environmental testing procedures for electronic and electrical items: Part 8 vibration (Sinusoidal) test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
NA (Frequency Range : 5 Upto 3000Hz)	15000.0

910

5154 - Lead Acid Traction Battery

Lead Acid Traction Battery

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Dimensions)	500.0
4 (Marking and polarity)	500.0
3.1 (Test For Capacity)	10000.0
3.4 (Cyclic Endurance Test)	50000.0
3.2 (Test for retention of Charge)	20000.0
3.3 (High Rate Discharge)	20000.0

911

IS 15622 (2017) - Pressed Ceramic Tiles - Specification (First Revision)

Pressed Ceramic Tiles - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6, Tables 5 to 9, Sl No (ii), (e) (Scratch Hardness of surface (Mohs' Scale)-IS13630 (Part 13):2019)	2000.0
6, Tables 5 to 9, Sl No (ii), (c) (Breaking of strength in N- IS13630 (Part 6):2019)	2000.0
6, Tables 8 and 9, Sl No (ii), (q) (Bulk Density-IS13630 (Part 2):2019)	1000.0
6, Tables 5 to 9, Sl No (ii), (b) (Modulus of rupture in N/mm²- IS13630 (Part6):2019)	2000.0
6, Tables 5 to 9, Sl No (ii), (a) (Water Absorption-IS13630 (Part 2):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (e-1,2,3) (Surface Flatness-Maximum deviation in percent from flatness-(Centre curvature, Edge curvature & warpage) -IS: 13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (c) (Straightness of sides(Facial sides)Maximum deviation in percent to corresponding work size- IS13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (d) (Rectangularity-Maximum deviation in percent to corresponding work size-IS: 13630 (Part1):2019)	500.0
6, Tables 5 to 9, Sl No (i), (b) (Dimension-Thickness-Deviation in percent from work size -IS: 13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (a) (Dimensions-Width -IS:13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (i), (a) (Dimensions-Length-IS13630 (Part1):2019)	1000.0
6, Tables 5 to 9, Sl No (iii), (a) (Resistance to staining IS 13630(8)/(7):2019)	1000.0
6. iii)b (Resistance to household chemicals and swimming pool water cleansers except HF and its compounds)	1500.0
6. iii)c (Resistance to acids and alkalis(with the exceptions of HF & its compounds))	1500.0
6.ii) k (Impact resistance-Co-efficient of restitution (on the lines of IS 13630(14):2019))	2000.0

912

IRS S 88 (2004) - Low maintenance Lead Acid Stationary Secondary Cells for S&T Installation

Low maintenance Lead Acid Stationary Secondary Cells for S&T Installation

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2 (Verifiational of Constructional requirements)	20000.0
7.3 (Verification of Marking and packing)	500.0
7.4 (Dimensions)	500.0
7.5 (Capacity in Ah)	20000.0
7.6 (Test for Loss of Capacity on storage in Ah)	20000.0
7.7 (Endurance Test)	90000.0
7.8 (Ampere-hour and watt hour efficiency test)	20000.0
7.9 (Test for Voltage during discharge in Ah)	1000.0
7.10 (Life Test total 1100 cycle)	100000.0
7.11 (Storage Test for 2 years)	20000.0
7.12 (Water Loss Test)	10000.0
7.13 (Equilibrium Float Current Test)	20000.0
7.14 (Sulphation Test)	20000.0
7.15 (Air Pressure Test)	10000.0

913

AS 1397 (2021) - Continuous hot-dip metallic coated steel sheet and strip - Coatings of zinc and zinc alloyed with aluminium and magnesium

Continuous hot-dip metallic coated steel sheet and strip - Coatings of zinc and zinc alloyed with aluminium and magnesium

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.4 (Both surface -Triple spot)	2000.0
3.2 (One surface- Single spot)	2000.0
2.2 (Sulfur)	500.0
2.2 (Carbon)	500.0
2.2 (Phosphorus)	500.0
2.2 (Mangnese)	500.0
2.3 (Tensile strength)	1000.0
2.3 (Yield Stress)	1000.0
2.3 (% Elongation)	1000.0
2.5.1 (Total Coated Thickness)	1000.0
2.5 (Base Metal Thickness)	1000.0
3.3 (Coating Adherence Test)	1000.0
2.4 (Bend Test)	1000.0
2.5 (Base Metal Thickness)	1000.0
3.3 (Coating Adherence Test)	1000.0
2.4 (Bend Test)	1000.0

914

MORTH : Part 5 (2013) - SPECIFICATIONS FOR ROAD AND BRIDGE WORKS/ASTM

SPECIFICATIONS FOR ROAD AND BRIDGE WORKS/ASTM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

915

EIL B224-000-79-41-PLS-01 : Part 5 (2019) - Job specification for surface preparation and protective coating

Job specification for surface preparation and protective coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

916

IEC 60896 : Part 21-22 (2004) - Stationary Lead Acid Batteries Valve Regulated Type

Stationary Lead Acid Batteries Valve Regulated Type

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Gas Emission Test)	30000.0
6.2 (High Current tolerance Test)	20000.0
6.6 (Content and durability of required marking)	500.0
6.7 (Material Identification)	3000.0
6.11 (Discharge Capacity)	60000.0
6.12 (Charge retention during Storage)	50000.0
6.13 (Float Service with daily discharges)	30000.0
6.14 (Recharge behaviour)	30000.0
6.15 (Service Life at an operating temp. at 40 Deg C)	300000.0
6.16 (Impact of a stress temperature of 50Deg C or 60 Deg C)	250000.0
6.17 (Abusive over discharge)	60000.0
6.19 (Low temperature sensitivity)	30000.0

917

IS 13252 (2010) - Information Technology Equipments, Class I Product

Information Technology Equipments, Class I Product

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.1.1.6 (Manual Controls)	2000.0
2.3.3 (Separations from Hazardous Voltages)	1000.0
2.5 (Limited Power Source)	1000.0
2.6 (Protective earthing Conductors and protective bonding Conductors)	2000.0
2.7 (Over Current and earth fault protection primary Circuit)	1000.0
2.8 (Protection requirements for safety interlocks)	500.0
2.9 (Humidity Condition)	10000.0
2.10.2 (Determination of Working Voltage)	1000.0
3 (Wiring Connection and Supplies)	1000.0
4.2.1,4.2.2,4.2.3,4.2.4 (Steady force Test)	1000.0
4.2.5 (Impact Test Apparatus)	500.0
4.2.6 (Drop Test)	1000.0
4.2.7 (Stress Relief Test)	1000.0
4.3.1 (Edges and corners)	500.0
4.3.4 (Securing of Parts)	500.0
4.3.6 (Direct Plug in Equipment)	1000.0
4.3.8 (Batteries)	1000.0
4.3.9 (Oil & Grease)	500.0
4.4.2 (Protected in operator access area)	1000.0
4.4.3 (Protected in restricted access Location)	1000.0
4.4.4 (Protected in service access Location)	1000.0
4.5.2. (Temperature Test)	1000.0
4.5.3. (Temperature Limits for Materials)	2000.0
4.5.4. (Touch Temperature Limits)	1000.0
4.5.5. (Resistance to abnormal Heat)	2000.0
4.6.3,4.6.4,4.6.4.1,4.6.4.2,4.6.4.3 (Top, Bottom and Side Opening)	500.0
4.6.5 (Adhesives for Constructional Purposes)	500.0
5.2 (Electric Strength)	5000.0
6.1.1,6.1.2 (Protection of Telecommunication network service person and user to network Protection from Hazardous Voltages)	1000.0
6.2.1 (Protection of equipments user from overvoltage on Telecommunication network)	1000.0
6.2.2 (Electrical Strength Test)	2000.0
6.3 (Protection of the Telecommunication wiring system from over heating)	2000.0
7.2 (Protection of cable distribution system service persons and user of other equipment connected to the system from hazardous voltage in the equipment)	2000.0
7.3 (Protection of equipment user from over voltages on the cable distribution)	1000.0
4.7.2,4.7.2.1,4.7.2.2 (Resistance to force (Reducing the risk of ignition and spread of flame))	1000.0
IS 13252 (PART 1) (Neutral conductor)	500.0
IS 13252 (PART 1) (Voltage Limit of Hand held equipment)	500.0
IS 13252 (PART 1) (Voltage Surge Test)	2000.0
2.1.1.8 (Energy Hazard DC Mains Supply)	1000.0

918

IS 616 (2017) - Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Marking & Instructions)	500.0
7.1.1 (Heating under normal Operating Conditions, Accessible parts)	5000.0
7.1.3 (Parts other than windings, providing Electrical Insulation)	1000.0
7.1.4 (Parts acting as a support or a mechanical barrier & Winding)	1000.0
7.2 (Heat Resistance of insulating Material)	1000.0
8.1 to 8.16 (Constructional Requirements with regard to the Protection against Electrical Shock)	1000.0
8.17 (Requirement of Insulating winding wires for use without additional interleaved insulation)	500.0
8.18 (Endurance Test for wound components with insulated winding wires without additional interleaved insulation)	500.0
8.19.1,&8..19.2 (Disconnection from the mains)	1000.0
8.20 & 8.21 (Main Switch)	500.0
9.1.2 & 9.1.3 (Shafts of operating, Knobs , handles, levers and the like)	500.0
9.1.4 (Terminals)	500.0
9.1.5 (Preset Controls)	1000.0
9.1.6 (Withdrawal of main Plugs)	1000.0
9.1.7 (Resistance to external s-force)	1000.0
9.2 (Removal of protective cover)	500.0
10.2 (Surge Test)	10000.0
10.3 (humidity Treatment)	20000.0
10.4 (Insulation Resistance and Dielectric Strength)	500.0
11.1 (Electrical Shock Hazard)	500.0
11.2,11.2.1, 11.2.2,11.2.3,11.2.4,11.2.5, (Heating)	3000.0
12.1.3 (Vibration Test)	5000.0
12.1.4 (Impact Test)	500.0
12.1.5 (Drop Test)	500.0
12.1.6 (Stress Relief Test)	500.0
12.2 (Fixing of actuating Elements)	1000.0
12.3 (Remote Control devices held in hand)	500.0

919

IS 1652 (2013) - Stationary cells and batteries, lead - Acid type with plante positive plates - Specification (Fourth Revision)

Stationary cells and batteries, lead - Acid type with plante positive plates - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Verification of Constructional Requirements)	30000.0
7 (Verification of Marking)	500.0
6.1 (Verification of Dimensions)	500.0
10.6 (Test for Capacity)	25000.0
10.11 (Test for Voltage during Discharge)	5000.0
10.10 (Ampere-hour and watt hour efficiency test)	10000.0
10.8 (Test for loss of Capacity on Storage)	20000.0
10.9 (Endurance Test)	45000.0
10.12 (Loss of water test)	10000.0
10.13 (Test for suitability of floating battery operation)	15000.0
10.14 (Short circuit & Internal Resistance Test)	20000.0

920

IS 6304 (1992) - Stationary batteries - Lead - Acid type - With pasted positive plates - Specification (Second Revision)

Stationary batteries - Lead - Acid type - With pasted positive plates - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3,4.4,4.6,,4.8,4.9,4.10 &7 (Visual Inspection)	10000.0
4.1,4.2,4.5,4.7&4.11 (Physical Verification)	25000.0
6 (Physical Verification)	500.0
8.6 (Capacity)	20000.0
8.7 (Capacity)	10000.0
8.8.1 (Ampere- Hour Efficiency)	7500.0
8.8.2 (Watt Hour Efficiency)	7500.0
8.9 (Capacity)	45000.0
8.1 (Voltage during Discharge)	5000.0
9.8 (Voltage)	10000.0

921

IS 14257 (2019) - Lead - Acid storage batteries for motor vehicles with light weight and high cranking performance - Specification (First Revision)

Lead - Acid storage batteries for motor vehicles with light weight and high cranking performance - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.3.1 (Physical Examination)	20000.0
9.3.2 (Dimensions and layout)	500.0
9.3.3 (Marking)	500.0
9.3.4 (5-hr capacity Test)	20000.0
9.3.5 (High rate discharge test at -15℃)	20000.0
9.3.6 (Cold cranking Ampere at -18℃)	20000.0
9.3.7 (Reserve Capacity Test)	20000.0
9.3.8 (Charge Acceptance test)	15000.0
9.3.9 (water loss in percent)	10000.0
9.3.10 (Charge retention test)	5000.0
9.3.11 (Light load Endurance test)	30000.0
9.3.12 (Life cycle test)	50000.0
9.3.13 (Over-charge Endurance test)	5000.0
9.3.14 (Electrolyte retention test)	5000.0
9.3.15 (Vibration resistance test)	10000.0
9.3.16 (Strength of terminal test)	5000.0
9.3.17 (Robustness to fastening test)	5000.0
Annex. B-1.2 (Residual Capacity Test)	10000.0

922

IS 16270 (2014) - Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Rated Capacity)	20000.0
8.2 (Endurance Test)	80000.0
8.3 (Charge retention test)	10000.0
8.4 (Cycling Endurance in photovoltaic application( Extreme Conditions))	90000.0
8.5 (Recovery from sulphation Test)	10000.0
8.6 (Water loss Test)	10000.0

923

IS 13369 (1992) - Stationary lead - Acid batteries (With Tubular Positive Plates) in monobloc container - Specification

Stationary lead - Acid batteries (With Tubular Positive Plates) in monobloc container - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.2 (Verification of Constructional Requirements)	20000.0
11.3 (Verification of Marking)	1000.0
11.4 (Verification of Dimensions)	1000.0
11.5 (Test for Capacity)	20000.0
11.8 (Ampere-hour and watt hour efficiency test)	10000.0
11.6 (Test for loss of Capacity on Storage)	10000.0
11.7 (Endurance Test)	45000.0
11.9 (Water loss test)	10000.0
11.1 (Equilibrium Float current test)	10000.0
11.5 (Test for Capacity at -13 deg C to -15 deg C)	20000.0

924

IS 8662 (2004) - Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision)

Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.6.xiii (Keeping properties)	5000.0
6.6.xii (Accelerated storage stability test, at 60 degC, 96 h)	3000.0
6.6.xi.b (Phthalic anhydride content of non-volatile vehicle)	3000.0
6.6.xi.a (Volume solids)	3000.0
6.6.x (Flash point)	1500.0
6.6.ix (Flexibility and adhesion)	1200.0
6.6.viii (Scratch hardness after 48 h air drying (1 000 g weight))	1500.0
6.6.vii (Water content (if suspected to be present)	1200.0
6.6.vi (Colour)	1200.0
6.6.v (Fineness of grind,)	1200.0
6.6.iv.b (Gloss , 60 deg)	1500.0
6.6.iv.a (Fnish)	1200.0
6.6.iii.d (Drying time Tack Free)	1200.0
6.6.iii.c (Hard dry at 70 DegC with 15 min flash- off time)	1200.0
6.6.iii.b (Drying time Hard Dry)	1200.0
6.6.iii.a (Drying time Surface Dry)	1200.0
6.6.ii (Mass, in kg/101itres)	1500.0
6.6.i.b (Viscosity byFord cup No. 4)	1200.0
6.6.i.a (Consistency)	1200.0
6.5 (Resistance to Alkali (for Finishing Only)	1500.0
6.4 (Resistance to Acid (for Finishing Only))	1500.0
6.3 (Durability( Normal Outdoor Exposer))	10000.0
6.2.6 (Application Properties)	1200.0
6.2.5 (Thinning Properties)	1200.0
6.2.4 (Skin Formation)	1200.0
6.2.3 (Freedom from Coarse Particles)	1200.0
6.2 (Condition in Container)	1200.0
6.1 (Composition)	1200.0

925

IS 1651 (2013) - Stationary cells and batteries, lead - Acid type (With Tubular Positive Plates) - Specification (Fourth Revision)

Stationary cells and batteries, lead - Acid type (With Tubular Positive Plates) - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.3 (Verification of Marking)	500.0
12.4 (Verification of Dimensions)	500.0
12.5 (Capacity)	25000.0
12.10 (Test for Voltage during Discharge)	10000.0
12.9 (Ampere-hour and watt hour efficiency test)	10000.0
12.7 (Test for loss of Capacity on Storage)	10000.0
12.8 (Endurance Test)	90000.0
12.11 (Water loss test)	10000.0
12.12 (Test for suitability of floating battery operation)	10000.0
12.13 (Short circuit & Internal Resistance Test)	15000.0
12.2 (Verification of Constructional Requirements)	25000.0
12.13 (Short circuit & Internal Resistance Test(Current more than 1000 Amps))	15000.0

926

IS 7372 (1995) - Lead - Acid storage batteries for motor vehicles - Specification (First Revision)

Lead - Acid storage batteries for motor vehicles - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.3 (Physical Examination)	20000.0
9.4 (Dimensions and layout)	500.0
9.5 (Marking)	500.0
9.6 (Air Pressure Test)	10000.0
9.7 (Capacity Test)	25000.0
9.9 (High rate discharge test at Normal Temperature)	15000.0
9.10 (High rate discharge test at Low Temperature)	20000.0
9.12 (Retention of Charge Test)	15000.0
9.13 (Resistance to Over Charge Test)	10000.0
9.14 (Life Test)	60000.0
9.15 (Storage Test)	25000.0
9.8 (Vibration Test)	10000.0

927

IEC 61373 (2010) - Vibration/Shock Test

Vibration/Shock Test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8[ Cat. 1 Class A] (Functional random vibration test)	15000.0
9[ Cat 1,Class A] (Simulated long-life testing at increased random vibration levels in Cat. 1 Class A)	45000.0
10 (Shock Test in Cat. 1 Class A & B)	10000.0
9[ Cat 1,Class B] (Simulated long-life testing at increased random vibration levels)	45000.0
8[ Cat. 1 Class B] (Functional random Vibration Test in Cat. 1 Class B)	15000.0

928

IS 1470 (1995) - Silicomanganese

Silicomanganese

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2.2 (Carbon)	1200.0
7.2.2 (Sulphur)	1200.0
7.2.2 (Phosphorus)	2000.0
7.2.2 (Silicon)	2000.0
7.2.2 (Manganese)	2000.0
7.2.2 (Arsenic )	2000.0
7.2.2 (Chromium + Nickel + Molybdenum )	3000.0
7.2.2 (Carbon)	1200.0
7.2.2 (Sulphur)	1200.0
7.2.2 (Phosphorus)	2000.0
7.2.2 (Silicon)	2000.0
7.2.2 (Manganese)	2000.0
7.2.2 (Arsenic )	2000.0
7.2.2 (Chromium + Nickel + Molybdenum )	3000.0
7.2.2 (Carbon)	1200.0
7.2.2 (Sulphur)	1200.0
7.2.2 (Phosphorus)	2000.0
7.2.2 (Silicon)	2000.0
7.2.2 (Manganese)	2000.0
7.2.2 (Arsenic )	2000.0
7.2.2 (Chromium + Nickel + Molybdenum )	3000.0

929

IS 164 (2015) - Ready mixed paint for road marking - Specification (Second Revision)

Ready mixed paint for road marking - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.6.2.2 (Toxic metals as Pb Cd Cr: (Atomic Absorption Spectrophotometric methods))	2000.0
5.6.2.1 (Volatile Organic Compounds (VOC): (IS 101 (Part 2/Sec 1) and IS 101 (Part 2/Sec 2)))	3000.0
xii (Keeping properties (IS 101 (Part 6/Sec 2)))	5000.0
xi (Mass in kg/10 litre, (IS 101 (Part 1/Sec 7)))	500.0
x (Flash point (IS 101 (Part 1/Sec 6)))	600.0
ix (Residue on sieve, Max, (IS 101 (Part 8/Sec 1)))	500.0
viii-b (Resistance to wear a) For Grade 2 (as refer in IS 164))	1000.0
viii-a (Resistance to wear a) For Grade 1 (As refer in IS 164))	1000.0
vii (Recoating property (As refer in IS 164))	600.0
vi (Resistance to bleeding (As refer in IS 164))	500.0
v (Wet Opacity (IS 101 (Part 4/Sec 1)))	600.0
iv (Colour (IS 101 (Part 4/Sec 2)))	500.0
iii (Finish (IS 101 (Part 3/Sec 4)))	500.0
ii (Consistency (Annex D))	500.0
i (Drying time, Max b) Hard dry (IS 101 (Part 3/Sec 1)))	500.0
5.5 table 1 i (Drying time, Max a) Surface dry (IS 101 (Part 3/Sec 1)))	500.0
5.4 (Lead Restriction, Max, (IS 101 (Part 8/Sec 5)))	1200.0
5.3 (Durability (Annex C) 25 days)	2000.0
5.2 (Applications (Annex B))	500.0

930

IS 158 (2015) - Ready mixed paint, brushing, bituminous, black, acid, alkali and heat resisting - Specification (Fourth Revision)

Ready mixed paint, brushing, bituminous, black, acid, alkali and heat resisting - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3,xvi (Keeping properties)	500.0
4.3,xv (Flash Point)	500.0
4.3,xiv (Resistance to heat)	200.0
4.3,xiii (Resistance to alkali)	1000.0
4.3,xii (Resistance to acid)	2000.0
4.3,xi (Volatile matter, percent by mass)	200.0
4.3,x (Protection against corrosion under conditions of condensation)	2000.0
4.3, ix (Stripping Test)	1000.0
4.3, viii (Flexibility and adhesion, bend test with 6.25 mm dia mandrel and type 1 apparatus)	1000.0
4.3,vii (Water Content,percent by mass)	100.0
4.3,vi (Mass, kg/10litre)	100.0
4.3,v (Colour)	100.0
4.3,iv (Wet opacity)	500.0
4.3,iii (Finish)	100.0
4.3,ii (Consistency)	1000.0
4.3,i (Drying time : Hard dry)	1000.0
4.2 (Lead Restrictions)	1500.0