NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb@nic.in

Scope List

Reset

1093 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

931

IS 2932 (2013) - Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.9,xiv (Wet opacity, (IS 101 (Part 4/Sec 1)))	350.0
6.9,xiii (Keeping properties, (IS 101 (Part 6/Sec 2)))	5000.0
6.9,xii (Accelerated storage stability test, (Annex G))	400.0
6.9,xi (Resistance to alkali(for finishing only), (Annex F))	1000.0
6.9,x (Resistance to acid (for finishing only), (Annex E))	1000.0
6.9,ix.b (Composition: Phthalic Anhydride Content, (IS 101 (Part 8/Sec 4)))	350.0
6.9,ix.a (Composition: Volume solids, (IS 101 (Part 8/Sec 6)))	350.0
6.9,viii (Flash point, (IS 101 (Part 1/Sec 6)))	350.0
6.9,vii.b (Flexibility and adhesion:Bend test (with 6.25 mm in type 1 apparatus), (IS 101 (Part 5/Sec 2)))	350.0
6.9,vii.a (Flexibility and adhesion:Scratch hardness (Load 1 000 g), (IS 101 (Part 5/Sec 2)))	1500.0
6.9, vi (Colour, (IS 101 (Part 4/Sec 2)))	350.0
6.9,v (Fineness of grind, microns (IS 101 (Part 3/Sec 5)))	350.0
6.9,iv.b (Gloss, 60º, (IS 101 (Part 3/Sec 4)))	350.0
6.9,iv.a (Finish, (IS 101 (Part 3/Sec 4)))	350.0
6.9,iii.c (Drying time: Tack free, (IS 101 (Part 3/Sec 1)))	350.0
6.9,iii.b (Drying time: Hard dry, (IS 101 (Part 3/Sec 1)))	1000.0
6.9,iii.a (Drying time: surface dry, (IS 101 (Part 3/Sec 1)))	1000.0
6.9,ii (Mass, kg/10litre (IS 101 (Part 1/Sec 7)))	1200.0
6.9,i.b (Viscosity by Ford cup No. 4 at 27 ± 2°C (IS 101 (Part 1/Sec 5)))	350.0
6.9,i. a (Consistency)	1000.0
6.8 (Lead Restriction, (IS 101 (Part 8/Sec 4)))	350.0
6.7.1.3 (Durability: Accelerated weathering test Xenon Arc (700hrs.) (Annex C-4))	35000.0
6.7.1.3 (Durability: Accelerated weathering test QUV apparatus (Lamp Type UV 313, Cycle UV 4 hrs and condensation 4 hrs) Total 360 hrs)	10000.0
6.7.1.1 (Durability (Normal outdoor exposure test) 12 Months (Annex C))	10000.0
6.6 (Application Properties)	350.0
6.5 (Thinning Properties)	350.0
6.4 (Skin formation)	350.0
6.3 (Freedom from Coarse Particles)	350.0
6.2 (Condition in Container)	350.0
6.1.1 (Composition)	350.0
6.1.2 (Total Non-Volatile Content (IS 101 Part 8/Sec 2))	500.0

932

IS 5410 (2013) - Cement paint - Specification (Second Revision)

Cement paint - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.8 ix (Recoating properties)	1200.0
4.8 viii (Pot life of mixed paint)	1200.0
4.8 vii (Water repellency)	1200.0
4.8 vi (Resistance to dry rubbing)	1200.0
4.8 v (Residue on sieve % by mass)	1200.0
4.8 iv (Fastness to light (250hrs))	12500.0
4.8iii (Colour)	1200.0
4.8 ii (Finish)	1200.0
4.8 i (Drying time Hard dry)	1200.0
4.7 (Keeping properties)	5000.0
4.6 (Durability Normal Out Door exposure Test 18 Months)	15000.0
Cl 4.4 (Lead Restriction)	1200.0
Cl 4.1 (Composition)	3500.0

933

IS 428 (2013) - Washable distemper - Specification (Third Revision)

Washable distemper - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.7 ix (ix)Acc storage stability)	1500.0
6.7 viii (viii) Resistance to alkali)	1000.0
6.7 Vii (vii) Recoating properties)	1000.0
6.7 Vi (vi) Residue on sieve % by mass)	200.0
6.7 v (v) Fastness to light)	4000.0
6.7 iv (iv) Colour)	500.0
6.7 iii (iii)Finish)	500.0
6.7 ii (ii) Consistency)	1000.0
6.7 i. (b) (Drying time b) Hard dry)	1000.0
6.7 i. (a) (Drying time a) surface dry)	1000.0
6.6 (Keeping properties)	5000.0
6.5 (Lead Restriction)	500.0
6.3 (Application)	500.0
6.2 (Thinning)	100.0
6.1 (Form and condition)	500.0
6.9.2.2 (toxic metals as lead, cadmium, chromium (VI) and their compounds)	1500.0
6.9.2.1 (volatile organic compounds % by mass)	2500.0

934

IS 16098 Part 1 (2013) - Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

935

IS 427 (2013) - Distemper, dry, colour as required - Specification (Third Revision)

Distemper, dry, colour as required - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3 (Lead Restriction)	500.0
4.2.2.ix (Resistance to dry rubbing IS 427 Annex F)	100.0
4.2.2.viii (Resistance to Alkali IS 427 Annex E)	100.0
4.2.2vii (Recoating properties IS 427 Annex D)	100.0
4.2.2.vi (Residue on sieve IS 427 Annex C)	100.0
4.2.2.v (Fastness to light 250 Hours Exposure Xenon arc Appartaus)	5000.0
4.2.2.iv (colour IS 101 (Part 4 /Sec 2))	100.0
4.2.2.iii (Finish IS 101 (Part 3/Sec 4))	100.0
4.2.2.ii (consistency IS 101 (Part 1/ Sec 5))	100.0
4.2.2 i (Drying Time Hard Dry)	200.0
4.1 (Form and Condtion)	100.0
Additional Parameters (Volatile Organic compound(VOC) S 101: Part 2/Sec 2 & Part 2/Sec 3)	3500.0
Additional Parameters (Toxic metals -- (as metal) Lead,, Chromium, Cadmium -- Atomic absorption spectrophotometer)	1500.0

936

IS 110 (2017) - Ready mixed paint, brushing, grey filler, for enamels for use over primers - Specification (Third Revision)

Ready mixed paint, brushing, grey filler, for enamels for use over primers - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3xiii (Keeping properties)	5000.0
4.3 xii (Flash point)	1200.0
4.3 xi (Flexibility and adhesion:b)bend test with 6.25 mm dia mandrel Type I apparatus)	1200.0
4.3 xi (Flexibility and adhesion: a Scratch Hardness Test 1000 g)	1200.0
4.3x (Residue on sieve ,percent by mass)	1200.0
4.3ix (Wet opacity m2/10 litre)	1200.0
4.3 viii (hold out property)	1200.0
4.3 vii (Flattning Property)	1200.0
4.3vi (colour)	1200.0
4.3 v (Dry Film thickness per coat by brush in microns)	1200.0
4.3 iii (Mass, kg/10litre)	1200.0
4.3 ii (b) Viscosity by Ford Cup no 4 at 27 (+/-)2 deg C)	1200.0
4.3ii (a)Consistency)	1200.0
4.3 i (i) Drying time, h b) hard dry)	1200.0
4.3 i (i) Drying time, h, a) surface dry )	1200.0
4.2 (Lead Restrictions)	2500.0
4.1 (Composition)	1200.0

937

IS 133 : Part 1 (2013) - Enamel, interior: (A) undercoating (B) finishing - Specification: Part 1 for household and decorative purposes (Fifth Revision)

Enamel, interior: (A) undercoating (B) finishing - Specification: Part 1 for household and decorative purposes (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.9, xiv (Keeping properties)	5000.0
5.9, viii (Fasteness to light)	5000.0
5.9,xiii (Accelerated storage stability test)	2000.0
5.9,xii (Volume solids percent)	1200.0
5.9,xi (Flash point)	1200.0
5.9,x,b (Flexibility and adhesion:Bend test with 6.25 mm dia Mandre in type 1 apparatus.)	1200.0
5.9,x,a (Flexibility and adhesion: Scratch hardness (Load 1 000 g), )	1200.0
5.9,ix (Resistance to water)	1200.0
5.9,vii (Wet opacity)	1200.0
5.9,vi (colour)	1200.0
5.9,v (Fineness of grind, microns)	1200.0
5.9, iv,b (Gloss, 60º)	1200.0
5.9,iv,a (Finish)	1200.0
5.9,iii b ( Viscosity by B 4 ford cup)	1200.0
5.9,iii a ( Consistency )	1200.0
5.9,ii (Mass, kg/10litre)	1200.0
5.9.i c (Drying time : Tack free)	1200.0
5.9.i b (Drying time : Hard dry)	1200.0
5.9.i a (Drying time : Surface dry)	1200.0
5.8 (Lead Restrictions)	2500.0
5.7 (Freedom from Yellowing)	1200.0
5.6 (Thinning Properties)	1200.0
5.5 (Skin formation)	1200.0
5.4 (Freedom from Coarse Particles)	1200.0
5.3 (Condtion in container)	1200.0
5.2 (Total Non-volatile content)	1200.0

938

IS 9000 : Part V : Sec 2 (1981) - Electric and Electronics items (size less than 1 cubic meter)

Electric and Electronics items (size less than 1 cubic meter)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

939

IS 9000 : Part II : Sec 2 (1977) - Electric and Electronics items (size less than 1 cubic meter)

Electric and Electronics items (size less than 1 cubic meter)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

940

IS 9000 : Part 5 : Sec 1&2 (1981) - Electric and Electronics items (size less than 1 cubic meter)

Electric and Electronics items (size less than 1 cubic meter)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

941

IS 694 (2010) - Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 1100 v (Fourth Revision)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 1100 v (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 1.i.a, ii.d , iii.a.4 (Conductor Resistance)	1500.0
Table 1. iii. a.1 , ii.a (Annealing Test (for copper))	1000.0
Table 1. iii. a.2 , ii.b (Tensile Test for aluminium)	1000.0
Table 1. iii. a.3 , ii.c (Wrapping Test (for Aluminium))	500.0
Table 1. iii. a.5 (Persulphate Test (for tinned copper conductor only)))	1000.0
Table 1. iii. b , ii.e (Tests for overall dimension and thickness of insulation/sheath)	1000.0
Table 1. iii. c.1, ii.f (Physical tests for insulation- Tensile strength and elongation at break)	1500.0
Table 1. iii. c.2 (Physical tests for insulation - Loss of mass test)	1500.0
Table 1. iii. c.3 (Physical tests for insulation - Ageing in air oven)	2000.0
Table 1. iii.c.4 (Physical tests for insulation - Shrinkage test)	1000.0
Table 1. iii.c.5 (Physical tests for insulation - Heat shock test)	1000.0
Table 1. iii. c.6 (Physical tests for insulation - Hot deformation Test)	500.0
Table 1. iii.c.7 (Physical tests for insulation - Thermal stability test)	1000.0
Table 1. iii. e.5, ii.j (Flammability Test)	500.0
Table 1. iii. c.11 , ii.k (Physical tests for insulation - Oxygen index test)	5000.0
Table 1. iii. c.12 , ii.m (Physical tests for insulation - Test for temperature index)	5000.0
Table 1. iii. c.13 , ii.n (Physical tests for insulation - Test for halogen acid gas evaluation)	5000.0
Table 1. iii. c.14 , ii.p (Physical tests for insulation - Test for smoke density rating)	5000.0
Table 1. iii. d.1 (Physical tests for sheath - Tensile strength and elongation at break)	1500.0
Table 1. iii. d.2 (Physical tests for Sheath - Loss of mass Test)	1500.0
Table 1. iii. d.3 (Physical tests for sheath - Ageing in air oven)	2000.0
Table 1. iii. d.4 (Physical tests for sheath - Shrinkage Test)	500.0
Table 1. iii. d.5 (Physical tests for sheath - Heat shock Test)	500.0
Table 1. iii. d.6 (Physical tests for sheath - Hot deformation Test)	500.0
Table 1. iii. d.7 (Physical tests for sheath - Thermal stability)	1000.0
Table 1. iii. d.8 (Physical tests for sheath - Oxygen Index Test)	5000.0
Table 1. iii. d.9 (Physical tests for sheath - Test for temperature Index)	5000.0
Table 1. iii. d.10 (Physical tests for sheath - Halogen acid gas evaluation)	5000.0
Table 1. iii. d.11 (Physical tests for sheath - Test for smoke density)	5000.0
Table 1. iii. e.1 (High Voltage Test (Water immersion Test))	3000.0
Table 1. iii. e.2 , ii.h (High voltage test or Spark test)	1500.0
Table 1.iii.e.3 , ii.g (Insulation resistance)	2000.0
Table 1. iii. e.4 (High voltage test (Cl. 10.2)(at room temperature))	1500.0
Table 1. iii. e.6 (Addition Ageing test (OU Cables only))	2000.0
- (Test on 2nd core)	2000.0
- (Test on 3rd core)	2000.0
- (Test on 4th core)	2000.0

942

IS 6911 (2017) - Stainless steel plate, sheet and strip - Specification (Second Revision)

Stainless steel plate, sheet and strip - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Erichsen Cupping Test)	2000.0
10 (Hardness )	2000.0
10 (Elongation)	1000.0
10 (Yield Stress)	1000.0
10 (Tensile strength)	1000.0
Cl 7.1 & 7.2 of Table 1 (Carbon (as C), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Silicon (as Si), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Manganese (Mn), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Nickel (as Ni), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Chromium (as Cr), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Molybdenum (Mo), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Sulphur (as S), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Phosphorus (as P), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Other element)	1200.0
7.1 & 7.2 (Copper)	1200.0
7.1 & 7.2 (Aluminium)	1200.0
7.1 & 7.2 (Niobium)	1200.0
7.1 & 7.2 (Titanium)	1200.0

943

IS 9974 : Part 1 (1981) - Specification for high pressure sodium vapour lamps: Part 1 general requirements and tests

Specification for high pressure sodium vapour lamps: Part 1 general requirements and tests

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Lamp Dimensions )	5000.0
5 (Marking)	5000.0
6 (Lamp Caps )	5000.0
7.2 (Lamp Starting & Warm-up Test )	5000.0
7.3 (Electrical characteristics)	10000.0
7.4 (Lamp Photometric characteristics)	15000.0

944

IS 15885 : Part 2 : Sec 13 (2012) - Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Marking)	1200.0
8 (Protection against accidental contact with live parts )	1200.0
9 (Terminals)	1200.0
10 (Provisions for protective earthing )	1200.0
11 (Moisture resistance & Insulation Resistance)	3500.0
12 (Electric strength)	1500.0
13 (Thermal endurance test for windings of ballasts )	5500.0
14 (Fault conditions)	2000.0
15 (Transformer heating)	2000.0
16 (Construction )	1200.0
17 (Creepage distances and clearances )	1200.0
18 (Screws, current-carrying parts and connections )	1200.0
19 (Resistance to Heat)	2000.0
19 (Resistance to Fire)	5000.0
19 (Resistance to Tracking)	5000.0
20 (Resistance to corrosion)	2000.0

945

IS 16104 (2012) - D.C. or A.C. supplied electronic control gear for led modules - Performance requirements

D.C. or A.C. supplied electronic control gear for led modules - Performance requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Marking )	1200.0
7 (Output Voltage and Current)	1200.0
8 (Total Circuit Power)	2000.0
9 (Circuit Power Factor)	1200.0
10 (Supply Current)	1200.0
12 (Operational Test for abnormal condition)	5000.0
13 (Temperature Cyclic Test)	10000.0
13 (Supply voltage Switching Test (upto 200 cycle) )	5000.0
13 (Accelerated Operational Life Test upto 200 hrs.)	5000.0

946

IS 16103 : Part 2 (2012) - Led modules for general lighting: Part 2 performance requirements

Led modules for general lighting: Part 2 performance requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Marking)	1200.0
5 (Dimension)	1200.0
7 (Power measurement)	2000.0
8.1 (Luminous flux)	5000.0
8.2 (Luminous intensity)	5000.0
8.3 (Module efficacy)	2000.0
9.1 (Chromaticity coordinates)	1000.0
9.1 (corelated colour temperature )	2000.0
9.2 (Colour rendering index (CRI) )	2000.0
10.2 (Lumen maintenance)	30000.0
10.3 (Temperature Cyclic Test)	10000.0
10.3 (Supply voltage Switching Test )	10000.0

947

IS 16103 : Part 1 (2012) - Led modules for general lighting: Part 1 safety requirements

Led modules for general lighting: Part 1 safety requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Marking)	1200.0
8 (Terminals)	1200.0
9 (Provisions for protective earthing)	1200.0
10 (Protection against accidental contact with live parts )	1200.0
11 (Moisture resistance)	2000.0
11 (Insulation Resistance)	1500.0
12 (High Voltage Test)	1500.0
13 (Fault conditions)	2000.0
14 (Conformity testing during manufacture)	5000.0
15 (Construction)	1200.0
16 (Creepage distances )	600.0
16 (clearances )	600.0
17 (Screws, current-carrying parts and connections)	1200.0
18 (Ball Pressure Test)	2000.0
18 (Glow Wire Test)	5000.0
18 (Tracking Index Test)	5000.0
19 (Resistance to Corrosion)	5000.0
21 (Heat Management)	2000.0

948

IS 16107 : Part 2 : Sec 1 (2012) - Luminaires performance: Part 2 particular requirements: Sec 1 led luminaire

Luminaires performance: Part 2 particular requirements: Sec 1 led luminaire

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Qualitative)	1200.0
7 (Luminaire power)	2000.0
8.1 (Luminous flux )	2000.0
8.2 (Lighting intensity )	5000.0
8.3 (Angular beam distribution)	1000.0
8.4 (Luminaire intensity distribution)	2000.0
8.5 (Luminaire efficacy )	2000.0
9.1 (Chromaticity coordinates )	1000.0
9.1 (correlated colour temperature )	2000.0
9.2 (Colour rendering index )	2000.0
10 (Life)	30000.0
10.2 (Lumen maintenance )	30000.0
10.3 (Endurance test)	55000.0

949

IS 10322 : Part 5 : Sec 4 (1987) - Specification for luminaires: Part 5 particular requirements: Sec 4 portable general purpose luminaires

Specification for luminaires: Part 5 particular requirements: Sec 4 portable general purpose luminaires

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13.2 (Visual Examination)	1200.0
13.3 (Mechanical Strength Test)	1200.0
13.4 (Endurance Test & Thermal Tests)	5500.0
13.5 (Resistance to Dust)	6000.0
13.5 (Resistance to Moisture)	6000.0
13.6 (Insulation Resistance)	2000.0
13.6 (Electric Strength)	3000.0
18 (Resistance to heat )	2000.0
18 (Resistance to fire )	5000.0
18 (Resistance to tracking )	5000.0

950

IS 10322 : PART 5 : SEC 3 (2012) - Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Marking )	1200.0
7 (Construction)	1200.0
8 (Creepage Distances )	600.0
8 (Clearances)	600.0
9 (Provision for earthing)	1200.0
10 (Terminals)	1200.0
11 (External & Internal wiring)	1200.0
12 (Protection against Electric Shock)	1200.0
13 (Endurance Test & Thermal Tests)	5500.0
14 (Resistance to Dust )	6000.0
14 (Resistance to Moisture)	6000.0
15 (Insulation Resistance )	2000.0
15 ( Electric Strength)	3000.0
18 (Resistance to heat )	2000.0
18 (Resistance to fire )	5000.0
18 (Resistance to tracking )	5000.0
17 (Photometric Tests)	10000.0

951

IS 10322 : Part 5 : Sec 2 (2012) - Luminaires: Part 5 particular requirements: Sec 2 recessed luminaires (First Revision)

Luminaires: Part 5 particular requirements: Sec 2 recessed luminaires (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Marking )	1200.0
7 (Construction)	1200.0
8 (Creepage Distances & Clearances)	1200.0
9 (Provision for earthing)	1200.0
10 (Terminals)	1200.0
11 (External & Internal wiring)	1200.0
12 (Protection against Electric Shock)	1200.0
13 (Endurance Test & Thermal Tests)	5500.0
14 (Resistance to Dust )	6000.0
14 (Resistance to Moisture)	6000.0
15 (Insulation Resistance )	2000.0
15 ( Electric Strength)	3000.0
18 (Resistance to heat )	2000.0
18 (Resistance to fire )	5000.0
18 (Resistance to tracking )	5000.0
17 (Photometric Tests)	10000.0
6 (Marking )	1200.0
7 (Construction)	1200.0
8 (Creepage Distances & Clearances)	1200.0
9 (Provision for earthing)	1200.0
10 (Terminals)	1200.0
11 (External & Internal wiring)	1200.0
12 (Protection against Electric Shock)	1200.0
13 (Endurance Test & Thermal Tests)	5500.0
14 (Resistance to Dust )	6000.0
14 (Resistance to Moisture)	6000.0
15 (Insulation Resistance )	2000.0
15 ( Electric Strength)	3000.0
18 (Resistance to heat )	2000.0
18 (Resistance to fire )	5000.0
18 (Resistance to tracking )	5000.0
17 (Photometric Tests)	10000.0

952

IS 210 (2009) - Grey iron castings - Specification (First Revision)

Grey iron castings - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
16 (Brinell Hardness)	2000.0
15 (Tensile Strength)	2500.0
6 (Chemical Composition (Sulphur))	500.0
6 (Chemical Composition (Phosphorus))	1000.0
9 (Microstructure)	3000.0

953

IS 10322 : Part 5 : Sec 1 (2012) - Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Marking )	1200.0
7 (Construction)	1200.0
8 (Creepage Distances & Clearances)	1200.0
9 (Provision for earthing)	1200.0
10 (Terminals)	1200.0
11 (External & Internal wiring)	1200.0
12 (Protection against Electric Shock)	1200.0
13 (Endurance Test & Thermal Tests)	5500.0
14 (Resistance to Dust )	6000.0
14 (Resistance to Moisture)	6000.0
15 (Insulation Resistance )	2000.0
15 ( Electric Strength)	3000.0
18 (Resistance to heat )	2000.0
18 (Resistance to fire )	5000.0
18 (Resistance to tracking )	5000.0
17 (Photometric Tests)	10000.0

954

IS 10322 : Part 1 (2014) - Luminaires: Part 1 general requirements and tests (First Revision)

Luminaires: Part 1 general requirements and tests (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Marking )	1200.0
4 (Construction)	1200.0
5 (External & Internal Wiring)	1200.0
7 (Provision for Earthing)	1200.0
8 (Protection against Electric Shock)	1200.0
9 (Ingress Protection 1st Characterictics)	6000.0
9 (Ingress Protection 2nd Characterictics)	6000.0
10 (Insulation Resistance)	2000.0
10 ( electric strength )	3000.0
11 (Creepage Distance )	600.0
11 (Clearance)	600.0
12 (Endurance Test and Thermal Test)	5500.0
13 (Resistance to heat )	2000.0
13 (Resistance to fire )	5000.0
13 (Resistance to tracking )	5000.0
14 (Screw Terminals)	1200.0
15 (Screwless Terminals & Electrical connections)	1200.0

955

IS 2339 (2013) - Aluminium paints for general purposes - Specification (First Revision)

Aluminium paints for general purposes - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Compostion)	200.0
5.1.1 (Leafing Value)	1500.0
5.3 i (Drying Time Hard dry)	200.0
5.3 ii (Consistency)	200.0
5.3 iii (Finish)	200.0
5.3 iv (Mass)	200.0
5.3 v (Wet Opacity)	500.0
5.3 vi (Flexibility and adhesion, bend test usingType 1 apparatus and 6.25 mm dia Mandrel)	200.0
5.3 vii (Resistance to humidity under condition of condensation)	3000.0
5.3viii (Flash point)	2000.0
5.3 ix (Keeping properties)	5000.0
5.2 (Lead Restriction)	500.0

956

IS 15489 (2013) - Paint, plastic emulsion - Specification (First Revision)

Paint, plastic emulsion - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.12 (Toxic metals such as lead, cadmium, chromium (VI))	3600.0
6.12 (Volatile organic compounds,)	2000.0
6.1 (Keeping properties)	5000.0
6.5 (Mass in kg/10 litre (IS 101 (Part 1/Sec 7)))	500.0
6.11 (Recoating properties, (Annexure J of IS 15489:2013))	2000.0
6.11 (Washability and cleanability (Annexure G of IS 15489:2013))	1900.0
6.11 (Resistance to alkali (Annexure F of IS 15489:2013))	500.0
6.11 (Accelerated storage stability test (Annexure H of IS 15489:2013))	700.0
6.11 (Colour (Annexure E of IS 15489:2013))	100.0
6.11 (Gloss at 60 degree d) Class D, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree c) Class C, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree b) Class B, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree a) Class A (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Finish (Annexure D of IS 15489:2013))	1200.0
6.11 (Consistency (Annexure B of IS 15489:2013))	1200.0
6.11 (Drying time a) Hard dry (Class C and D) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Hard dry (Class A and B) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Surface dry (Class C and D) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Surface dry (Class A and B))	200.0
6.9 (Lead Restriction)	700.0
6.8 (Durability Test for Exterior Use Only Accelerated weathering apparatus QUV ( for 21 days))	15200.0
6.7 & 6.11 (Fastness to Light (Xenon Arc apparatus for 500 hrs) (IS 101 Part 4/ Sec 3))	15000.0
6.6 (Opacity (IS 101 ( Part 1/Sec 3)))	200.0
6.2 (Conditions in the Container)	200.0
6.3 (Thinning)	200.0
6.4 (Application Properties)	200.0
6.1 (Composition)	200.0

957

IS 10322 : Part 5 : Sec 5 (2013) - Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Marking )	1200.0
6 (Construction)	1200.0
6 (Creepage Distances )	600.0
6 (Clearances)	600.0
6 (Provision for earthing)	1200.0
6 (Terminals)	1200.0
6 (External & Internal wiring)	1200.0
6 (Protection against Electric Shock)	1200.0
6 (Endurance Test & Thermal Tests)	5500.0
6 (Resistance to Dust)	6000.0
6 (Resistance to Moisture)	6000.0
6 (Insulation Resistance )	2000.0
6 ( Electric Strength)	3000.0
6 (Resistance to heat )	2000.0
6 (Resistance to fire )	5000.0
6 (Resistance to tracking )	5000.0
6 (Photometric Tests)	10000.0

958

IS 16102 : Part 2 (2017) - Self - Ballasted led lamps for general lighting services: Part 2 performance requirements (First Revision)

Self - Ballasted led lamps for general lighting services: Part 2 performance requirements (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Marking)	1200.0
6 (Dimension)	1200.0
8 (Power )	2000.0
9 (Luminous Flux)	5000.0
10 (Centre Beam intensity)	3000.0
11 (Beam angle)	3000.0
12 (Chromaticity Co-ordinates & Colour rendering index)	5000.0
13 (Lumen Maintenance)	85000.0
15 (Harmonics & PF)	2000.0

959

IS 2074 (2015) - Ready Mixed Paint, Air Drying, Red Oxide - Zinc Chrome, Priming - Specification

Ready Mixed Paint, Air Drying, Red Oxide - Zinc Chrome, Priming - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.6, xii (Keeping properties)	5000.0
5.6,xi (Accelerated storage stability test)	200.0
5.6,x.c (Resistance to salt spray)	500.0
5.6,x.b (Resistance to sea water (applicable for marine paints only))	50.0
5.6,x.a (Resistance to humidity)	2500.0
5.6,ix (Volume solids)	200.0
5.6,viii (Flash point)	500.0
5.6,vii.b (Flexibility and adhesion: Scratch hardness (load 1000g))	100.0
5.6,vii.a (Flexibility and adhesion:Bend test (with 6.25 mm dia mandrel and in type 1 apparatus))	100.0
5.6,vi (Colour)	50.0
5.6,v (Fineness of grind, microns)	100.0
5.6,iv.a (Finish)	100.0
5.6,iii.b (Drying: hard dry)	100.0
5.6,iii.a (Drying: Surface dry)	100.0
5.6,ii (Mass, kg/10litre)	200.0
5.6,i. b (Viscosity by Ford cup No. 4 at 27 ± 2°C)	200.0
5.6,i. a (Consistency)	200.0
5.5 (Lead Restriction)	200.0
5.3 (Compatibility with thinner)	200.0
5.1.2 (Volatile vehicle)	200.0
5.1.1.b (Synthetic red oxides of iron red oxide (as Fe2O3))	1000.0
5.1.1.a (zinc oxide)	500.0
5.1.1.a (chromic anhydride)	1000.0
5.1.1.a (Zinc chrome)	500.0
5.1.b (Driers)	50.0
5.1.a (Pigment, percent by mass)	1200.0

960

IS 6394 (2006) - Ultrasonic testing of seamless metallic tubular products by contact and immersion methods - Code of practice (Second Revision)

Ultrasonic testing of seamless metallic tubular products by contact and immersion methods - Code of practice (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 6394 (Ultrasonic examination)	2000.0