| 91 |
Customized specification for V Bar - Customized specification for V Bar |
Customized specification for V Bar |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Tensile Strength at yield as per ASTM D 882) |
4000.0 |
|
| - (Flexural Strength as per ASTM D 790) |
3000.0 |
|
| - (Heat deflection temperature at 264 psi as per ASTM D 648) |
2000.0 |
|
| - (Oxygen Index as per ASTM D 2863) |
5000.0 |
|
|
| 92 |
System-1 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - System -1 (F9 + P6+ F6B + F2. Total DFT 345 microns) EIL SPEC B224-000-79-41-PLS-01 REV 6 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS |
System -1 (F9 + P6+ F6B + F2. Total DFT 345 microns) EIL SPEC B224-000-79-41-PLS-01 REV 6 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 ("Cyclic Test
Salt Spray : 72 hrs.
Drying in air: 16 hrs.
UV-A340 nm weather meter: 80 hrs.
One cycle: 168 hrs.
(25 cycles at 168 hrs. each cycle)
(ASTM D5894)") |
95000.0 |
|
| 2 ("100% Humidity Test
(ASTM D2247)") |
20000.0 |
|
|
| 93 |
ASTM C 920 (2018) - Elastomeric Joint Sealants / Adhesives |
Elastomeric Joint Sealants / Adhesives |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7 (Test for Extrudability (on the lines of ASTM C 1183)) |
1000.0 |
|
| 8.1 (Rheological (Flow) Properties, Vertical and / or Horizontal displacement (on the lines of ASTM C 639)) |
3000.0 |
|
| 8.1 (Indentation Hardness (on the lines of ASTM C 661 / ASTM D 2240),) |
2000.0 |
|
| 8 (Tack - Free Time (on the lines of ASTM C 679)) |
1000.0 |
|
| 9 (Adhesion and Cohesion of Joints under cyclic movement (Concrete substrate - on lines of ASTM C 719)) |
10000.0 |
|
| 7 (Effect of Heat Ageing (on lines of ASTM C 1246)) |
4000.0 |
|
| 8 (Effect of Accelerated Weathering (On the lines of ASTM C 793) using QUV or Xenon Arc Weatherometer.) |
15000.0 |
|
| 9 (Test for staining and Colour Change (on lines of ASTM C 510) 100 hr exposure.) |
10000.0 |
|
| 8 (Test for Adhesion -In-Peel (on the lines of ASTM C 794)) |
5000.0 |
|
| ASTM (Material identification / verification by FTIR) |
2000.0 |
|
| 9 (Test for Adhesion and Cohesion under cyclic Movement (on lines of ASTM C 719) Glass Substrate) |
10000.0 |
|
| 9 (Test for Adhesion and Cohesion under cyclic Movement (on lines of ASTM C 719) Aluminium Substrate) |
10000.0 |
|
|
| 94 |
Customized Specification for Cotton Overall Material - Customized Specification for Cotton Overall Material |
Customized Specification for Cotton Overall Material |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (100% Cotton Fabric) |
2000.0 |
|
| - (GSM(gm/sq.m)) |
1000.0 |
|
| - (Colour) |
500.0 |
|
| - (Flat Coat Collar) |
500.0 |
|
| - (Two Flap pockets with snap buttons on chest) |
500.0 |
|
| - (Two Patch pockets on Back) |
500.0 |
|
| - (Two way concealed heavy duty industrial (brass/Nylon)Zip fastening) |
2000.0 |
|
| - (Pen pocket on left sleeve) |
500.0 |
|
| - (Elasticized Back) |
500.0 |
|
| - (Hanger loop on collar) |
500.0 |
|
| - (Reflective tapes on arms and legs) |
500.0 |
|
| - (Side Vents) |
500.0 |
|
| - (Adjustable cuffs and ankle openings) |
500.0 |
|
| - (Bartacking done in places where more strength is needed to support extra load) |
500.0 |
|
|
| 95 |
Customized Specification for Nylon PA 66 Roller(Finish Material) - Nylon PA 66 Roller(Finish Material) |
Nylon PA 66 Roller(Finish Material) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Density as per ASTM D 792) |
1000.0 |
|
| - (Shore D hardness as per ASTM D 2240) |
1000.0 |
|
| - (Water absorption as per ASTM D 570 for 24 hours) |
2000.0 |
|
| - (Base material identification by FTIR method) |
2000.0 |
|
|
| 96 |
RDSO SPECIFICATION No. M&C/PCN/120-2011 (Revision –1) (2011) - SPECIFICATION FOR ENAMEL, INTERIOR (a) UNDERCOATING (b) FINISHING WITH FIRE RETARDANT PROPERTIES |
SPECIFICATION FOR ENAMEL, INTERIOR (a) UNDERCOATING (b) FINISHING WITH FIRE RETARDANT PROPERTIES |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Table No. 1 Sr. No. 15 (Fire retardant properties (Annexure A of RDSO SPECIFICATION No. M&C/PCN/120-2011 (Revision –1))) |
2000.0 |
|
|
| 97 |
IS 1969(P-1):2019 - Fabric |
Fabric |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Breaking Strength of Fabric (Ravelled Strip 5x20 cm.) Length wise) |
1000.0 |
|
| - (Elongation at Break Length wise) |
1000.0 |
|
|
| 98 |
IS 456:2000 - PLAIN AND REINFORCED CONCRETE -CODE OF PRACTICE |
PLAIN AND REINFORCED CONCRETE -CODE OF PRACTICE |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 99 |
IS 456-II (2000) - Plain and Reinforced Concrete - CONCRETE CHEMICAL |
Plain and Reinforced Concrete - CONCRETE CHEMICAL |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 100 |
IP CODE : IS/IEC :60529 (2001 reaff : 2019) - Degree of protection provided by Enclosure(IP Code) |
Degree of protection provided by Enclosure(IP Code) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 13.2 First Characteristic Numeral 1 (13.2 First Characteristic Numeral 1 :Protection against solid foreign objects of 50 mm dia and greater) |
7500.0 |
|
| 13.2 First Characteristic Numeral 2 (13.2 First Characteristic Numeral 2 :Protection against solid foreign objects of 12.5 mm dia and greater) |
7500.0 |
|
| 13.2 First Characteristic Numeral 3 (13.2 First Characteristic Numeral 3 : Protected against solid foreign objects of 2.5 mm dia and greater) |
7500.0 |
|
| 13.2 First Characteristic Numeral 4 (13.2 First Characteristic Numeral 4 :protected against solid foreign object of 1.0 mm dia and greater) |
7500.0 |
|
| 13.4/13.5 First Characteristic Numeral 5 (13.4/13.5 First Characteristic Numeral 5 : Dust Protected) |
7500.0 |
|
| 13.4/13.5 First Characteristic Numeral 6 (13.4/13.5 First Characteristic Numeral 6 : Dust - Tight) |
7500.0 |
|
| 14.2.1 Second Characteristic Numeral 1 (14.2.1 Second Characteristic Numeral 1 : Protected against vertically falling water drops) |
7500.0 |
|
| 14.2.2 Second Characteristic Numeral 2 (14.2.2 Second Characteristic Numeral 2 : Protection against vertically falling water drops when enclosure tilted upto 15 degree) |
7500.0 |
|
| 14.2.3 second characteristic numeral 3 (14.2.3 second characteristic numeral 3:Protected against spraying water) |
7500.0 |
|
| 14.2.4 Second characteristic numeral 4 (14.2.4 Second characteristic numeral 4 with oscillating tube or spray nozzle) |
7500.0 |
|
| 14.2.5 Second characteristic numeral 5 (14.2.5 Second characteristic numeral 5: Protected against Water Jet) |
7500.0 |
|
| 14.2.6 Second characteristic numeral 6 (14.2.6 Second characteristic numeral 6: Protected against powerful water Jet) |
7500.0 |
|
| 14.2.7, Second characteristic numeral 7 (14.2.7, Second characteristic numeral 7:Protected against the effects of temporary immersion in water) |
7500.0 |
|
| 14.2.8, Second Characteristic numeral 8 (14.2.8, Second Characteristic numeral 8: Protected against the effects of continuous immersion in water.
if water has entered, it shall not be sufficient to interfere with the correct operation of the equipment or impair safety.) |
7500.0 |
|
|
| 101 |
ILC Of paper - Customized Specification for the ILC of paper |
Customized Specification for the ILC of paper |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Substance (Grammage),g/sq.m) |
- |
|
| - (Thickness,Microns) |
- |
|
| - (Tensile Index(MD), Nm/g) |
- |
|
| - (Tensile Index(CD), Nm/g) |
- |
|
| - (Tear Index(mN.sq.m/g)MD) |
- |
|
| - (Tear Index(mN.sq.m/g) CD) |
- |
|
| - (Brightness,ISO(%)) |
- |
|
| - (Opacity(%)) |
- |
|
| - (One Minute Cobb(g/sq.m)) |
- |
|
| - (Double Fold(Numbers)MD) |
- |
|
| - (Double Fold(Numbers)CD) |
- |
|
| - (Wax Pick) |
- |
|
| - (Smoothness(Bendtsen),ml/min.) |
- |
|
| - (pH) |
- |
|
| - (Moisture Content(%)) |
- |
|
| - (Ash Content(%)) |
- |
|
|
| 102 |
NTH(WR)/MECH/CUSTOM/010 (2024) - Fire Blankets Specification as per EN 1869 latest edition or any other National/Internation Specification or OEM/Manufacturer custom Specification - Requirements for fire blankets that are not reusable and that are intended for use by one person. |
Fire Blankets Specification as per EN 1869 latest edition or any other National/Internation Specification or OEM/Manufacturer custom Specification - Requirements for fire blankets that are not reusable and that are intended for use by one person. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Mechanical and Physical Parameters, Fire Performance Test Cooking oil and Hydrocarbon Fuel, Electrical Resistance Test as per EN 1869 latest edition or any other National/International Standard specification or OEM/Manufacturer custom specification.) |
33000.0 |
|
|
| 103 |
NTH(WR)/MECH/CUSTOM/009 (2024) - Performance requirements for, and the maximum capacity of, small single use fire extinguishers of the aerosol type with metal bodies as per BS-6165 latest edition or any National/ Internation Standards Specification or OEM/ Manufacturer custom Specification |
Performance requirements for, and the maximum capacity of, small single use fire extinguishers of the aerosol type with metal bodies as per BS-6165 latest edition or any National/ Internation Standards Specification or OEM/ Manufacturer custom Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Test Carried out for Content, Construction, Performance, Class A, B, F and Dielectric Test as per BS 6165 latest edition or Any other National /International Standard Specification or OEM/Manufacturer custom Specification.) |
74000.0 |
|
|
| 104 |
None - Custom spec. for cup calibration |
Custom spec. for cup calibration |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Cup Volume Calibration) |
2000.0 |
|
|
| 105 |
NTH(WR)/MECH/CUSTOM/008 (2024) - Fire Extinguisher Performance Test as per relevant IS or any other National /International product specification or manufacturer/customer specification |
Fire Extinguisher Performance Test as per relevant IS or any other National /International product specification or manufacturer/customer specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Fire Extinguisher Performance Test for general fire as per the test method in specified in the relevant IS or any other National /International Product specification or manufacturer/customer specification) |
5000.0 |
|
|
| 106 |
M&C/ PCN/ 127 /2020 (Rev 2.0 ) Dated Sep 2020 (2020) - RDSO Specification for Anti-Graffiti Clear coat for the exterior painting of Railway coaches, Diesel & Electric locomotives” |
RDSO Specification for Anti-Graffiti Clear coat for the exterior painting of Railway coaches, Diesel & Electric locomotives” |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Drying Time at (27± 2)˚C , i)Surface Dry/Touch Dry
As per IS:101-86 (Part- 3/ Sec- 1)Reaffirmed 2017) |
400.0 |
|
| 1 (Drying Time at (27± 2)˚C ii)Hard Dry As per IS:101-86 (Part- 3/ Sec- 1)Reaffirmed 2017) |
400.0 |
|
| 1 (Drying Time at (27± 2)˚C iii) Recoating Time
As per IS:101-86 (Part- 3/ Sec- 1)Reaffirmed 2017) |
400.0 |
|
| 2 (Finish (IS 101 (Part 3/Sec 4): 1987) |
400.0 |
|
| 3 (Gloss at 60˚
IS : 101-88 (Part 4/Sec-4),) |
1200.0 |
|
| 4 (Flexibility & Adhesion
(By Mandrel size 6.25 mm)
IS : 101-88 (Part -5/Sec-2),) |
1200.0 |
|
| 5 (Impact Resistance test at Height 100cm (39.37 inch) and weight 2.0 Kg (4.409 pound) on 0.50 mm thick cured panel. ASTM-D-2794) |
1500.0 |
|
| 6 (Adhesion Test ( Cross Cut Tape Test) ASTM-D-3359) |
1200.0 |
|
| 8 (Protection against corrosion under conditions of condensation (500 hrs)
IS: 101-88 (Part- 6 /Sec- 1),) |
15000.0 |
|
| 7 (Consistency/Efflux Time at (27± 2)˚C
IS : 101-89 (Part -1 Sec-5),) |
1500.0 |
|
| 9 (Solvent MEK Rub Test 100 DS ASTM D-5402) |
1500.0 |
|
| 10(a) (ACCELERATED TESTS
Resistance to 30 % ,w/v (a)Citric acid for 3 Hours
appendix III) |
1000.0 |
|
| 10(b) (ACCELERATED TESTS (b) Resistance to 5% ,v/v Ammonia for 20 Minutes
appendix III) |
1000.0 |
|
| 10(c) (ACCELERATED TESTS (c) Resistance to Lubricating oil for 24 Hours
appendix III) |
1000.0 |
|
| 10(d) i (ACCELERATED TESTS (d) Resistance to Solvents for 20 Minutes
(i)Acetone appendix III) |
1000.0 |
|
| 10(d) ii (ACCELERATED TESTS
d) Resistance to Solvents for 20 Minutes
(ii) Toluene appendix III) |
1000.0 |
|
| 11 (Mass in Kg/10 litres (IS : 101-87 (Part -1/ Sec7),Reaffirmed 2019)) |
1000.0 |
|
| 12 (Flash Point deg.C
(IS: 101-87 (Part- 1/ Sec6),Reaffirmed 2019)) |
1000.0 |
|
| 13 (Keeping Property/Shelf Life for 1 year) |
10000.0 |
|
| 14 (Anti Graffiti test ASTM D-6578) |
5000.0 |
|
| 15 (Identification of Base Material/Resin By FTIR METHOD) |
2000.0 |
|
| 16 (Coverage ( Spreading Capacity) , Min. , at 1-4 microns DFT, By Spray, Dipping, Roller, Wiping method
appendix-I) |
1200.0 |
|
| 17 (Dry Film Thickness per coat in micron, by Wipe/Spray
APPENDIX-I) |
1000.0 |
|
| 18 (Pencil Hardness ASTM –D- 3363) |
1500.0 |
|
| 19 (Volume Solid,%
APPENDIX-I) |
2000.0 |
|
| 20 i (Durability Tests :
Accelerated Weathering by (Fluorescent UV-Condensation Type for 750 Hours
ASTM-G-154 (APPENDIX-IV)
Cycle 4 Hrs. U.V. Light from UV-B lamps with a peak emission @ 313 nm. and 4 Hours Condensation alternatively, temp. 50 ˚C) |
45000.0 |
|
| 20 ii (Durability Tests :
Accelerated Weathering by Xenon Arc for 2000hours
DIN- 53387 Superseded by
DIN EN ISO 4892-2) |
120000.0 |
|
|
| 107 |
IS / ASTM / EN - Concrete Admixture & Concrete Additives |
Concrete Admixture & Concrete Additives |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 10262 (Preparation of Concrete (control & with admixture)) |
10000.0 |
|
| 7.2.1 of IS 9103 (Slump Test for both control specimen and with admixture, in mm) |
4000.0 |
|
| 8.2.1 of IS 9103 (Compressive Strength of Concrete (control specimen & with admixture) one duration, N/mmm^2) |
10000.0 |
|
| 8.2.1 of IS 9103 (Compressive Strength of Concrete (control specimen & with admixture) three duration, N/mmm^2) |
15000.0 |
|
| 8.2.1 of IS 9103 (Compressive Strength of Concrete (control specimen & with admixture) four duration, N/mmm^2) |
18000.0 |
|
| 8.2.1 of IS 9103 (Compressive Strength of Concrete (control specimen & with admixture) five duration, N/mmm^2) |
25000.0 |
|
| 8.2.3 of IS 9103 (Length Change after 28 days (control and with admixture specimen), in %) |
4000.0 |
|
| 8.2.3 of IS 9103 (Length Change (control and with admixture specimen) after two duration (28 days & 6 months), in %) |
8000.0 |
|
| 8.2.3 of IS 9103 (Length Change (control and with admixture specimen) after three duration (28 days, 6 months & 1 year), in %) |
15000.0 |
|
| Part 5 / Sec 3 of IS 516 (Carbonation test (control specimen and with admixture), in mm) |
5000.0 |
|
| EN 12390 (Part 8) (Depth of water penetration (control specimen and with admixture), in mm) |
10000.0 |
|
| ASTM C 1012 (Change in length due to sulphate attack (control specimen and with admixture) after one duration, in %) |
5000.0 |
|
| ASTM C 1012 (Change in length due to sulphate attack (control specimen and with admixture) after three duration, in %) |
12000.0 |
|
| ASTM C 1012 (Change in length due to sulphate attack (control specimen and with admixture) after four duration, in %) |
15000.0 |
|
| BS 1881 -122 (Water Absorption on prepared specimens (both control and with admixture)) |
2000.0 |
|
| ASTM C 1293 - 08 (Alkali Silica Reactivity in concrete (control and with admixture) one duration, Change in length in %) |
5000.0 |
|
| ASTM C 1293 - 08 (Alkali Silica Reactivity in concrete (control and with admixture) two duration (7 days & 1 month), Change in length in %) |
8000.0 |
|
| ASTM C 1293 - 08 (Alkali Silica Reactivity in concrete (control and with admixture) three duration (7 days, 1month & 3 month), Change in length in %) |
15000.0 |
|
|
| 108 |
IS 2633 - Uniformity of Coating on Zinc Coated Articles |
Uniformity of Coating on Zinc Coated Articles |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Uniformity of Coating) |
2000.0 |
|
|
| 109 |
IS 12943:1990 (Reaffirmed 2020) - Brass Glands for PVC Cables- Specification. This standard covers requirements and dimensions for single compression brass glands for PVC cables of voltage grade up to and including 3.3 kV. |
Brass Glands for PVC Cables- Specification. This standard covers requirements and dimensions for single compression brass glands for PVC cables of voltage grade up to and including 3.3 kV. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5 (All tests specified in the standard) |
17000.0 |
|
| 5.2 (Torque) |
3000.0 |
|
| 5.3 (The distance through which the mandrel moves during the test period of 6 hours shall not exceed 6 mm.) |
4000.0 |
|
| 5.4 (Electrical resistance between the earth bond attachments) |
5000.0 |
|
| 5.5 (Degree of Protection) |
3000.0 |
|
| 6 (The dimensions of the gland and rubber ring shall be as given in Table 1.) |
2000.0 |
|
|
| 110 |
IS 14364 : 1996 - SURFACE CLEANER, LIQUID |
SURFACE CLEANER, LIQUID |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Description) |
1000.0 |
|
| - (Odour) |
500.0 |
|
| - (Colour) |
500.0 |
|
| - (Stability) |
3000.0 |
|
| - (Cleaning Property) |
1000.0 |
|
| - (Applicability) |
500.0 |
|
| - (Total non-volatile matter , percent by mass,) |
1000.0 |
|
| - (pH) |
1000.0 |
|
| - (QAC content, percent by mas s (calculated as
cetylpyridinium chloride)) |
1500.0 |
|
|
| 111 |
BS EN 62444:2013 (2013) - Cable Glands for Electrical Installations |
Cable Glands for Electrical Installations |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5 (Type tests) |
20000.0 |
|
|
| 112 |
BS 6121-1:2005 (2005) - Armour Glands -Requirements and test methods |
Armour Glands -Requirements and test methods |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.2.2.1 (Equipotential Bonding) |
2500.0 |
|
| 4.2.1.1 (Cable Retention/Armour clamp tensile strength) |
2500.0 |
|
| 4.2.1.2 (Resistance to Impact) |
2500.0 |
|
| 4.2.1.3 (Resistance to excess Torque) |
2500.0 |
|
| 4.2.3.1 (Ingress Protection) |
2500.0 |
|
| 4.2.2.2 (Electrical connection to the metallic layer(s)
of cable) |
2500.0 |
|
| 4.2.2.4 (Protective Connection to Earth) |
2500.0 |
|
| 4.2.2.3 (Insulation Resistance) |
2500.0 |
|
|
| 113 |
MMDTS -22001 - Schedule of Technical Requirements for Anodized Aluminium Braille Stickers for Signage on Railway Coaches |
Schedule of Technical Requirements for Anodized Aluminium Braille Stickers for Signage on Railway Coaches |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Abrasion Resistance) |
3000.0 |
|
| - (Acid Corrosion Resistance) |
1500.0 |
|
| - (Heat Resistance at 120 deg. C for 3 hours) |
1500.0 |
|
| - (Adhesion Between Basic and Braille Layers test) |
2000.0 |
|
| - (Stain Resistance Test) |
1000.0 |
|
| - (Ease of Cleaning) |
1000.0 |
|
| - (Chemical composition of Braille and Base Layers) |
5000.0 |
|
| - (Corrosion resistance from Neutral Salt Spray) |
21000.0 |
|
| - (Accelerated Weathering Test) |
35000.0 |
|
|
| 114 |
IS 8540 - Glass Cleaner |
Glass Cleaner |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Colour) |
500.0 |
|
| - (Odour) |
500.0 |
|
| - (Toxicity) |
3000.0 |
|
| - (Stability) |
1000.0 |
|
| - (Application and Performance) |
500.0 |
|
| - (Water content) |
1500.0 |
|
| - (Flash Point) |
1000.0 |
|
| - (Non-Volatile Matter Content) |
1000.0 |
|
| - (pH Value) |
1000.0 |
|
| - (Test for Cleaning Efficiency) |
1500.0 |
|
| - (Test for Corrosion or Discolouration) |
1500.0 |
|
|
| 115 |
ASM Vol 10 (1975) - FAILURE ANALYSIS AND PREVENTION |
FAILURE ANALYSIS AND PREVENTION |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| ASM (Failure investigation of metallic component and suggestions to avoid re occurrence of the failure) |
50000.0 |
|
|
| 116 |
- - Non Woven Geo Textiles |
Non Woven Geo Textiles |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Mass per unit area as per ASTM D 5261) |
1000.0 |
|
| - (Tensile Strength as per ASTM D 4632) |
4000.0 |
|
| - (Thickness as per IS 1060(P 5)Sec 3) |
1000.0 |
|
|
| 117 |
IS 164 : 2023 (2023) - Ready-Mixed Paint for Road Marking — Specification |
Ready-Mixed Paint for Road Marking — Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Table 1 (Drying time a) Surface dry (IS 101 (Part 3/sec 1))) |
600.0 |
|
| Table 1 (Drying time b) Hard dry (IS 101 (Part 3/Sec 1))) |
600.0 |
|
| Table 1 (Consistency) |
600.0 |
|
| Table 1 (Finish, (IS 101 (Part 3/Sec 4))) |
600.0 |
|
| Table 1 (Colour, (IS 101 (Part 4/Sec 2))) |
600.0 |
|
| Table 1 (Wet opacity, percent, (IS 101 (Part 4/Sec 1))) |
600.0 |
|
| Table 1 (Recoating property, Annexure E) |
600.0 |
|
| Table 1 (Resistance to bleeding, Annexure F) |
600.0 |
|
| Table 1 (Mass in kg/10 liter, (IS 101 (Part 1/Sec 7))) |
600.0 |
|
| Table 1 (Keeping properties (12 Months), (IS 101 (Part 6/Sec 2))) |
5000.0 |
|
| Table 1 (Early wash out resistance (for Type 2 only), Annexure G) |
1000.0 |
|
| Table 1 (No pick up time (for type 2 only), Annexure H) |
1000.0 |
|
| Table 1 (Non Volatile matter , (IS 101 (Part 8/sec 2))) |
600.0 |
|
| Table 1 (Volume solid, (IS 101 (Part 8/sec 6))) |
800.0 |
|
| Table 1 (Taber Abrasion resistance, mg weight loss after 500 cycles using CS10 wheel with 500 g on each load (for type 2 only), Annexure J) |
2000.0 |
|
| Table 1 (Scrub resistance, Annexure K) |
2000.0 |
|
| Table 1 (Resistance to accelerated weathering 500 hours (for type 2 only), Annexure L) |
30000.0 |
|
| Table 1 (Flexibility (for type 2 only), (IS 101 (Part 5 /sec 2 ))) |
600.0 |
|
| Table 1 (VOC, percent, (IS 101 (Part 2 /sec 4))) |
2000.0 |
|
| Table 1 (Resistance to wear, Annexure M) |
3000.0 |
|
| 5.4 (Lead Restriction (IS 101 (Part 8/Sec 5), or by Atomic
Absorption Spectrometer (AAS) or by ICP.)) |
1000.0 |
|
|
| 118 |
- - Customs specification for Chemical NTH WR |
Customs specification for Chemical NTH WR |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Salt spray test for 100 hours) |
4000.0 |
|
|
| 119 |
IS 6956 : 2001(Reaffirmed 2022) - Cover paper-Specification |
Cover paper-Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Burst Index (KPa.m²/g)) |
1000.0 |
|
| - (pH) |
1000.0 |
|
| - (Tensile Index(Nm/g)- MD) |
1000.0 |
|
| - (Tensile Index(Nm/g)- CD) |
1000.0 |
|
| - (Opacity Percent) |
1000.0 |
|
| - (Brightness) |
2000.0 |
|
| - (One minute Cobb Test (g/m²)) |
2000.0 |
|
| - (Smoothness(Bendtsen)ml./min.) |
2000.0 |
|
| - (Folding Endurance -MD) |
750.0 |
|
| - (Folding Endurance -CD) |
750.0 |
|
| - (Bending Stiffness Index,Nm⁶/Kg3 -MD) |
500.0 |
|
| - (Bending Stiffness Index,Nm⁶/Kg3 -CD) |
500.0 |
|
| - (Wax Pick) |
1000.0 |
|
| - (Grammage (g/m²)) |
1000.0 |
|
|
| 120 |
IS 6956 (2001) - Cover paper - Specification (First Revision) |
Cover paper - Specification (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
