NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director.nthwr-ca@gov.in

Scope List

Reset

636 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

IS/RDSO-GE/0001:23 (2023) - Specification for Track Ballast

Specification for Track Ballast

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.2 (Aggregate Abrasion Value, Average Value in %)	2000.0
2.2 (Aggregate Impact Value, Average value in %)	2000.0
2.2.3 (Water Absorption, in %)	1000.0
2.3 (Sieve Analysis, Retention on 65mm sq. mesh sieve, in %)	1000.0
203 (Sieve Analysis, Retention on 40mm sq. mesh sieve, in %)	1000.0
2.3 (Sieve Analysis, Retention on 20mm sq. mesh sieve, in %)	1000.0

- - Custom Specification for coal analysis-General Chemical (WR)

Custom Specification for coal analysis-General Chemical (WR)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Ash Content%)	1500.0

Customized specification for VIP frenchie Pro Brief Colour 90 cm. as per TDS Index no. 41294 - Customized specification for VIP frenchie Pro Brief Colour 90 cm. as per TDS Index no. 41294

Customized specification for VIP frenchie Pro Brief Colour 90 cm. as per TDS Index no. 41294

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Nomenclature)	500.0
- (Identification Mark/Marking)	500.0
- (Fibre Composition)	1000.0
- (Count)	500.0
- (Dimensional Change)	1000.0
- (Wales and Course)	500.0
- (pH)	1000.0
- (Colour fastness to washing)	1000.0
- (Size)	500.0
- (Waist band width)	500.0
- (Side length(including waist band))	500.0
- (Full width flat)	500.0
- (Centre height (including waist band))	500.0
- (Pouch with front(bottom))	500.0
- (Half leg open)	500.0
- (Width of top elastic)	500.0

Customized specification for VIP FRENCHIE COLOURED 85 CMS as per TDS Index no. 41546 - Customized specification for VIP FRENCHIE COLOURED 85 CMS as per TDS Index no. 41546

Customized specification for VIP FRENCHIE COLOURED 85 CMS as per TDS Index no. 41546

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Nomenclature)	500.0
- (Identification Mark/Marking)	500.0
- (Fibre Composition)	1000.0
- (Count)	500.0
- (Wales and Course)	500.0
- (pH value)	1000.0
- (Size)	500.0
- (Waist band width)	500.0
- (Side length)	500.0
- (Full width flat)	500.0
- (Central height(including waist band))	500.0
- (Pouch width(bottom))	500.0
- (Half leg open)	500.0
- (Width of inner elastic)	500.0

Customized specification for Camber Tray Set as per TDS Index no. 34442 - Customized specification for Camber Tray Set as per TDS Index no. 34442

Customized specification for Camber Tray Set as per TDS Index no. 34442

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Dimensions of Camber large tray)	500.0
- (Dimensions of camber medium tray)	500.0
- (Dimensions of camber small tray)	500.0
- (Weight of camber large tray)	500.0
- (Weight of camber medium tray)	500.0
- (Weight of camber small tray)	500.0
- (Colour)	500.0
- (Material Identification)	2000.0
- (Identification mark/marking)	500.0
- (Design)	500.0

Custom specification CSD Canteen Chemical Lab samples - Custom specification CSD Canteen Chemical Lab samples

Custom specification CSD Canteen Chemical Lab samples

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Camphor analysis (Please refer annexure for the test result of Camphor samples)	6000.0
AGARBATTlS - SPECIFICATION (Please refer annexure for the test result (Agarbattis/Incense sticks))	7000.0
Cosmetic products (Please refer annexure for the test results)	5000.0

Customized Specification for Non Metallic Liners/Packing Plates for Use in CASBUS Bogies - Customized Specification for Non Metallic Liners/Packing Plates for Use in CASBUS Bogies

Customized Specification for Non Metallic Liners/Packing Plates for Use in CASBUS Bogies

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Specific Gravity as per ASTM D 790)	1000.0
- (Hardness as per ASTM D 2240)	1000.0
- (Tensile Strength at yield as per ASTM D 638)	2000.0
- (Flexural Modulus as per ASTM D 790)	2000.0
- (Water absorption at 23(+/-)1deg.C for 24(+1/2, -o)hours)	2000.0

17908 (2023) - Fibre Cement Sheet - Lightweight Concrete Sandwich Panels

Fibre Cement Sheet - Lightweight Concrete Sandwich Panels

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2 (Overall Length, in mm)	1000.0
6.2 (Overall Width, in mm)	1000.0
6.2 (Thickness, in mm)	1000.0
6.2 (Indentation Depth, in mm)	500.0
6.2.1.1 (Straightness of Edge, in mm/m)	1000.0
6.2.1.2 (Squareness of edge, in mm/m)	1000.0
6.3 (Density, in kg/m^3)	1000.0
6.4.1 (Bending Strength (Three Point Loading), N/mm^2))	4000.0
6.4.2 (Bending Strength (Uniformly Distributed Load), in N/m^2)	4000.0
6.5 (i) (Impact Test (Small Hard Body impact - Surface damage),)	1500.0
6.5 (i) (Impact Test (Small hard body impact - Perforations))	1500.0
6.5 (ii) (Impact Test (Large soft body impact), deformation in mm)	1500.0
6.6.2 (Tensile Strength, in N/mm^2)	2000.0
6.6.3 (Screw Withdrawal Strength, in kN)	1500.0

303 (2024) - Plywood for General Purpose

Plywood for General Purpose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Length, in mm)	500.0
8.1 (Width, in mm)	500.0
8.2 (Thickness, in mm)	500.0
8.3 (Squareness, in mm/m)	500.0
8.3 (Edge Straightness, in mm/m)	500.0
5 (Classification by Appearance)	1000.0
9 (Workmanship and finish,)	1000.0
11.3.1 (a) (Glue Adhesion - Water Resistance Test)	2000.0
11.3.1 (b) (Glue Adhesion Test - Water Resistance Test - BWR Grade)	2000.0
11.3.1 cb) (Glue Adhesion Test - Water Resistance Test - BWP Grade)	2000.0
11.3.2 (Mycological Test)	1500.0
11.4 (Moisture Content, in %)	1000.0
11.5 (Static Bending Strength (Modulus of Rupture -Along), in N/mm^2)	1000.0
11.5 (Static Bending Strength (Modulus of Rupture - Across), in N/mm^2)	1000.0
11.5 (Static Bending Strength (Modulus of Elasticity-Along), in N/mm^2)	1000.0
11.5 (Static Bending Strength (Modulus of Elasticity- Across), in N/mm^2)	1000.0

CUS/SR/MECH-55 (2024) - Mechanical Properties of Metal

Mechanical Properties of Metal

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions, mm)	2000.0
2.0 (Brinell Hardness, HBW)	2000.0
5.0 (Powder Coating Thickness, micron)	2000.0
6.0 (Tensile strength, N/mm²)	1000.0
7.0 (Yield strength, N/mm²)	1000.0
8.0 (Percentage Elongation, %)	1000.0
9.0 (Weight, kg)	1000.0

CUS/SR/MECH-8 - Composite Sandwich Shutter

Composite Sandwich Shutter

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Deflection)	3000.0
2.0 (Breaking load)	3000.0

CUS/SR/MECH-14 - Trek Bottle

Trek Bottle

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Height)	1000.0
2.0 (Weight)	1000.0
3.0 (Capacity)	1000.0
4.0 (Hot water test)	3000.0
5.0 (Cold water test)	3000.0
6.0 (Chemical composition, % by mass)	6000.0

IS 14268 (2022) - Uncoated stress relieved low relaxation seven - Wire (Ply) strand for prestressed concrete - Specification (First Revision)

Uncoated stress relieved low relaxation seven - Wire (Ply) strand for prestressed concrete - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2.5 (Relaxation Losses)	50000.0
6.2.4 (Relaxation Losses)	50000.0
6.1 (Nominal Mass)	1500.0
6.1 (Nominal Area )	1000.0
6.1 (Nominal Diameter )	1000.0
6.1 (Nominal Mass of strand - IS 14268: 2022.)	1500.0
6.1 (Nominal Cross- Sectional Area of Strand- IS 14268: 2022.)	1000.0
6.1 (Nominal Diameter of strand- IS 14268: 2022.)	1000.0
6.2.3 (Elongation)	1000.0
6.2.2 (0.2% Proof Load)	1000.0
6.2.2 (Breaking Strength)	3000.0
6.2.2 (0.2% Proof Load of Strand - IS 1608 (Part 1): 2022/ IS 14268: 2022.)	1000.0
6.2.2 (Breaking Load of Strand- IS 1608 (Part 1): 2022/ IS 14268: 2022.)	3000.0
6.2.3 (Total Elongation under Load on gauge length of 600 mm- IS 14268: 2022.)	1000.0
4.2 (Length of lay of 9.5 mm strand)	1000.0
4.2 (Length of lay for dia 15.2mm)	500.0
4.5 (Visual observation)	1000.0
4.2 (Centre wire shall have 1.5% greater in diameter than the surrounding wires - IS 14268: 2022.)	1000.0
Table 2 (Cl 6.1, Cl 4.2) (Dimension and Mass)	1000.0
4.5 (Workmanship and Finish)	1000.0
4.1.2 (Chemical composition (Annexure for NABL parameters))	3500.0
4 (Chemical composition (Annexure for non-NABL parameters))	3000.0
Note 1 (Modulus of Elasticity, N/mm2)	1000.0
6.3 (Tensile Strength of Strand- IS 1608 (Part 1): 2022/ IS 14268: 2022, MPa.)	1000.0

CUS/SR/MECH-27 (2022) - Stainless Steel Kadai

Stainless Steel Kadai

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Thickness)	1000.0
2.0 (Inside diameter)	1000.0

CUS/SR/MECH-11 - Insulated Tiffin Carrier

Insulated Tiffin Carrier

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Weight)	1000.0
2.0 (Capacity)	1000.0

NTH(WR)/MECH/CUSTOM/022-CSD-TDS-Durastone Cookware HA Stone Non-Stick BYK -Tawa (2024) - CSD-TDS-Durastone Cookware HA Stone Non-Stick BYK -Tawa

CSD-TDS-Durastone Cookware HA Stone Non-Stick BYK -Tawa

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Identification and Marking)	-
2 (Product Dimension, in mm as per TDS / relevant Product IS specification)	1000.0
3 (Weight in g as per TDS / relevant Product IS specification)	1000.0
4 (Capacity in L, as per TDS / relevant Product IS Specification)	500.0
5 (Workmanship and Finish- Visual Examination as per IS 1660 / relevant product specification of National or International standard Test method specified)	500.0
6 (Non-Stick Coating thickness, in µm as per IS 9730 / IS 6012 or any other relevant International or National standard test method specified)	2000.0
7 (Non-Stick Quality test, (Coating shall permit the test foods to be removed intact & coating surfaces to be wiped clean.) as per IS 1660 or relevant product specification or any other International / National Standard test method)	1000.0
8 (Finish of the coating - Visual Defects Test as per IS 1660 or any other International/national Standard or relevant product specification. Non-stick coatings shall be free from defects visible to naked eye.)	1000.0
9 (Salt-Water Corrosion Test, As per IS 9730 No defects additional to those initially present shall be observed in the coating.)	2000.0
10 (Adhesion Test – Cross hatch Test, As per IS 9730 No complete squares and not more than 5 percent of the total cross hatched area of the coating shall be lifted from the base and wall of the utensil.)	2000.0
11 (Adhesion Test – Peel Test,As per IS 9730 Peeled away coating length shall not be greater than 2 mm.)	2000.0
12 (Abrasion Resistance, As per IS 1660:2009 When the coating surface is rubbed two or three times with emery paper or emery cloth with emery conforming to grit number 180 of IS 715 ( Part 1) using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface.)	500.0
13 (Hardness Test as per IS 1660:2009)	500.0
14 (Test on Handle- Visual Examination as per IS 1660 Handle shall be sufficiently strong to support a mass in the utensil equivalent to three times the mass of the water capacity of the utensil in the position of normal use without visible permanent deformation of the handle or utensil)	500.0
15 (Body Assembly-Visual as per TDS / IS 1660 Stay cool handle fitted to body)	1000.0
16 (Coating Thickness by Microscopic Method as per IS 5523)	2500.0
17 (Material of Utensil as per TDS declaration /IS 21 / IS 1660 / any other relevant product specification specified National or International Standard Test Method)	3500.0
18 (Material of Lid as per TDS Declaration / IS 1660 refered product specification and method / any other relevant product specification specified in the international or National standard)	3500.0

IS 1660 (2009) - Wrought aluminium utensils - Specification (First Revision)

Wrought aluminium utensils - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Dimension, mm)	1000.0
8 (Workmanship & finish)	1000.0
7.2 (Test on Handle)	500.0
8.4.1.2 (Finish of the coating)	500.0
8.4.2 (Coating thickness test)	2500.0
8.4.3 (Abrasion resistance test)	500.0
8.4.5 (Hardness test)	500.0
4 (Materials of Lid)	3500.0
4 (Materials of utensil)	3500.0
TDS-1 (Weight)	500.0
8.5 (Non-Stick Unreinforced Plastics Coatings on Domestic Cooking Utensils)	8000.0
8.5 (Coating thickness test as per IS 9730)	2000.0
TDS-2 (Capacity , ml)	500.0

IS 2074 : 2023 (2023) - READY MIXED PAINT, AIR DRYING, RED OXIDE-ZINC CHROME PRIMING ― SPECIFICATION

READY MIXED PAINT, AIR DRYING, RED OXIDE-ZINC CHROME PRIMING ― SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Composition)	300.0
5.3 (Compatibility with Thinner)	100.0
5.4 (Freedom from Objectionable Impurities)	100.0
5.5 (Lead Restriction)	100.0
Table 1 (Consistency (Annexure C))	100.0
Table 1 (Viscosity by ford cup No. 4 at 27±2°C ((Part l/Sec 5))	500.0
Table 1 (Mass, in kg/10 l, (Part l/Sec 7))	500.0
Table 1 (Drying time, h, Max: a) Surface dry ((Part 3/Sec 1))	500.0
Table 1 (Drying time, h, Max: a) Hard dry ((Part 3/Sec 1))	500.0
Table 1 (Finish, (IS 101 Part 3/Sec 4))	500.0
Table 1 (Gloss 60°, Max (IS 101 Part 4/ sec 4))	500.0
Table 1 (Fineness of grind, microns, Max (IS 101 Part 3/Sec 5))	500.0
Table 1 (Colour (IS 101 (Part 4/Sec 2)))	500.0
Table 1 (Flexibility and adhesion: a) Bend test with 6.25mm dia mandrel and in type 1 apparatus) (IS 101 (Part 5/Sec 2)))	500.0
Table 1 (Flexibility and adhesion: b) Scratch hardness ( Load 1 000g ) (IS 101 (Part 5/Sec 2)))	500.0
Table 1 (Flash point (IS 101 (Part l/Sec 6)))	500.0
Table 1 (Volume solids, (IS 101 (Part 8/Sec 6)))	1.0
Table 1 (Resistance to humidity under conditions of condensation a) Resistance to humidity, (IS 101 (Part 6/Sec 1)))	499.0
Table 1 (b) Resistance to seawater (applicable for marine paints only), Annexure D)	1000.0
Table 1 (Accelerated storage stability test, Annexure F)	500.0
Table 1 (Keeping properties for 12 Months, (IS 101 (Part 6/Sec 2)))	5000.0
Table 2 (Consistency, Annexure C of IS 2074)	300.0
Table 2 (Hard dry, h, Max (IS 101 (Part 3/Sec 1)))	500.0
Table 2 (Non- volatile vehicle, (IS 101 (Part 8/Sec 2)))	500.0
Table 1 (Wet opacity, (IS 101 (Part 4/ Sec 1)))	500.0
Table 1 (c) Resistance to salt spray, (Annexure E of 2074), (IS 101 (Part 6/Sec 1)))	500.0

Customized Specification for ILC of Paper - Customized Specification for ILC of Paper

Customized Specification for ILC of Paper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Ash at 900 deg. C as per IS 1060(Part 5/Sec 3))	-
- (ISO Brightness as per IS 1060(part 4/Sec 13))	-
- (Opacity as per IS/ISO 2471)	-

IBR 1950 (2023) - Qualified Boiler Welder's Certificate

Qualified Boiler Welder's Certificate

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IBR 1950 (Welder qualification)	4500.0
IBR-1950, Chapter -XIII (IBR Welder Test - Tube/Pipe (MMAW)- Horizontally Fixed)	3500.0
IBR-1950, Chapter -XIII (IBR Welder Test - Tube/Pipe (GTAW+ MMAW)- Horizontally Fixed)	4500.0
NTH Additional Charges for Testing (Scientist Charges)	5000.0
IBR-1950, Chapter -XIII (IBR Welder Test - Tube/Pipe (GTAW+ MMAW)- Vertically Fixed)	4500.0
IBR-1950, Chapter -XIII (IBR Welder Test - Tube/Pipe (MMAW)- Vertically Fixed)	3500.0
Chapter XIII (Certification of welder per position of welding on Plate (SMAW/FCAW) (Plate and Electrodes not supplied by NTH))	3000.0
Chapter XIII (Certification of welder on Pipe & Branch Pipe by TIG/GTAW)	9000.0
Chapter XIII (Certification of welder per position of welding on Pipe/Tube by MMAW)	4500.0
Chapter XIII (Certification of welder per position of welding on Pipe by TIG/GTAW)	4500.0
Chapter XIII (Certification of welder per position of welding on Tube by TIG/GTAW)	4500.0
Chapter XIII (Certification of welder per position of welding on Plate (SMAW+TIG / GTAW)(Plate and Electrodes not supplied by NTH))	3500.0

Customized Specification for Nylon material - Customized Specification for Nylon material

Customized Specification for Nylon material

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Specific Gravity as per ASTM D 792)	1000.0
- (Hardness as per ASTM D 2240)	1000.0
- (Tensile Strength at yield as per ASTM D 638)	2000.0
- (Flexural Modulus as per ASTM D 790)	2000.0
- (Water absorption as per ASTM D 570)	2000.0

Customized specification for ASTM D 638 - Customized specification for ASTM D 638

Customized specification for ASTM D 638

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength and Elongation as per ASTM D 638)	3000.0

Custom specifications for cosmetic products (2024) - Custom specifications for cosmetic products

Custom specifications for cosmetic products

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Custom specifications for cosmetic products (Please refer to the annexure for the result)	5000.0

Customized specification for Bharat Bucket Plastic 18 Ltr as per CSD Index no. 34037 - Customized specification for Bharat Bucket Plastic 18 Ltr as per CSD Index no. 34037

Customized specification for Bharat Bucket Plastic 18 Ltr as per CSD Index no. 34037

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Nomenclature of the item)	500.0
- (Outer dia.from top(approx))	500.0
- (Height(approx))	500.0
- (Weight with tolerance)	500.0
- (Capacity with tolerance)	500.0
- (Colour)	500.0
- (Active ingredients (HDPE))	2000.0
- (Parts and their specifications)	500.0
- (Identification Marks /Marking)	500.0

Customized specification for Bharat Marvel Bucket (Big) as per CSD Index no. 34455 - Customized specification for Bharat Marvel Bucket (Big) as per CSD Index no. 34455

Customized specification for Bharat Marvel Bucket (Big) as per CSD Index no. 34455

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Nomenclature of Item)	500.0
- (Dimensions with tolerances)	500.0
- (Weight with tolerance)	500.0
- (Active ingredients(PP/HD Powder))	2000.0
- (Identification Marks/marking)	500.0

None - Customer specification for General chemical and Metal oil fuel -NTH WR

Customer specification for General chemical and Metal oil fuel -NTH WR

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Volatile Organic Compounds)	4000.0

NTH(WR)/MECH/CUSTOM/021 (2024) - Fence Items and Accessories - Barbed Wire

Fence Items and Accessories - Barbed Wire

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Line Wire Diameter as per IS 278)	1000.0
2 (Point/Barb Wire Diameter as per IS 278)	1000.0
3 (Designation & Type as per IS 278)	1000.0
4 (Barbing Pitch as per IS 278)	1000.0
5 (Barb Length as per IS 278)	1000.0
6 (Tensile Strength of Barbed Wire as per IS 278)	2000.0
7 (Tensile Strength of Line Wire as per IS 278)	2000.0
8 (Mass of Zinc Coating (GSM) as per IS 4826)	1500.0

NTH(WR)/MECH/CUSTOM/020 (2024) - Fence Items and Accessories - Concerina Coil

Fence Items and Accessories - Concerina Coil

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimensions of Blade Tear Blade (TBBT): Blade Length : Width of Blade: Distance between Blades (C-C):)	1000.0
2 (Coil Diameter)	1000.0
3 (Number of Loops)	1000.0
4 (Dimension of G.I Wire in mm)	1000.0

NTH(WR)/MECH/CUSTOM/019 (2024) - Fence Items and Accessories - GI Core Wire (Raw Material) and Galvanized Steel Strip

Fence Items and Accessories - GI Core Wire (Raw Material) and Galvanized Steel Strip

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Diameter of core wire as per IS 280)	1000.0
2 (Mechanical Properties as per IS 1608)	4000.0
3 (Mass of Zinc Coating (GSM) as per IS 6745/ IS 4826)	1200.0
4 (Galvanized Steel Strip Mechanical Properties as per IS 277)	7000.0
5 (Galvanized Steel Strip Thickness as per IS 277)	1000.0
1 (Diameter of core wire as per IS 280)	1000.0
2 (Mechanical Properties as per IS 1608)	4000.0
3 (Mass of Zinc Coating (GSM) as per IS 6745/ IS 4826)	1200.0
4 (Galvanized Steel Strip Mechanical Properties as per IS 277)	7000.0
5 (Galvanized Steel Strip Thickness as per IS 277)	1000.0

NTH(WR)/MECH/CUSTOM/018 (2024) - Fence Items and Accessories - GI Anchor Rod

Fence Items and Accessories - GI Anchor Rod

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Mass of Zinc Coating (DFT/GSM) as per ISO 2808/IS 4759/IS 4826)	1200.0
2 (Dimensions)	1000.0
3 (Mechanical Property as per IS 5986 Grade 235 / IS 2062 GRADE E250)	5000.0

First
Prev
2
3
4
5
Next
Last