NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum@nth.gov.in

Scope List

Reset

764 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

151

Customized Specification for FRP Chajja - Customized Specification for FRP Chajja [-]

Customized Specification for FRP Chajja

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength)	2000.0
- (Compression Strength)	3000.0
- (Flexural Strength)	3000.0
- (Thickness)	1000.0

152

RDSO Specification No. M&C/PCN/100/2018 - POLYURETHANE SURFACER (TWOPACK)

POLYURETHANE SURFACER (TWOPACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying time a) Surface dry b) Hard dry c) Hard dry at 70°C)	3600.0
2 (Consistency)	1200.0
3 (Finish)	1200.0
4 (Colour)	1200.0
5 (Dry film thickness)	1200.0
6 (Volume solids, %)	2000.0
7 (Scratch hardness (1.5Kg Load))	1200.0
9 (Flashpoint a) Component ‘A’ b) Component ‘B’)	2400.0
10 (Fineness of Grind)	1200.0
11 (Pot life (After induction time) i) 27±2°C ii) 40±2°C)	1500.0
12 (Mass in Kg/10 litres)	1200.0
13 (Keeping properties)	2000.0
14 (Theoretical spreading rate)	2000.0
15 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix of two components at 27± 2 °C in Supply condition)	1200.0

153

RDSO SPECIFICATION M&C/PCN/100/2018 PUTTY - UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK)

UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying time: a)Surface dry b) Hard dry c)Hard dry time at 70 Deg. C)	3600.0
2 (Consistency)	1200.0
3 (Stopping properties)	2000.0
4 (Rubbing properties)	2000.0
5 (Hold out Property)	2000.0
6 (Adhesion & Compatibility of Paint System)	2000.0
7 (Pot life ,at 27±2 Deg. C)	1500.0
8 (% solids)	1200.0
9 (Keeping properties)	5000.0

154

IS 15850 (2009) - Nuclear grade boron carbide - Specification

Nuclear grade boron carbide - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clauses 4.2.1 and 4.2.2 (Total Boron In Boron Carbide)	2000.0

155

CGRSP rubber pad as per RDSO Specification - CGRSP rubber pad as per RDSO Specification

CGRSP rubber pad as per RDSO Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Compression Set)	2000.0
- (Modulus at 100% Elongation)	2000.0
- (Elongation at Break)	2000.0
- (Tensile Strength)	2000.0
- (Shore hardness)	1000.0
- (Tension Set Subject to 50% Stretch)	2000.0
- (Tensile Strength after ageing at 100±1ºC for 72+0/-2 hrs.)	3000.0
- (Tensile Strength(Retension after ageing))	1000.0
- (Elongation at Break After ageing at 100±1ºC for 72+(0/-2) hrs)	3000.0
- (Elongation at Break (Retention after ageing))	1000.0
- (Thickness)	1000.0
- (Specific Gravity)	1000.0
- (Ash Contents)	2000.0
- (Electrical resistance before immersion as per appendix "G")	2000.0
- (Electrical resistance after immersion as per appendix "G")	3000.0
- (Adhesion Strength test)	2000.0

156

GFN Liners as per RDSO Specification - GFN Liners as per RDSO Specification [-]

GFN Liners as per RDSO Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Internal Cavity)	1000.0
- (Water absorption)	2000.0
- (Cross Breaking Load)	2000.0
- (Glass Filler)	2000.0
- (Specific Gravity)	1000.0
- (Dielectric Strength)	5000.0
- (Volume Resistivity)	3000.0

157

Customized Specification for Printed Papers/Books - Customized Specification for Printed Papers/Books [-]

Customized Specification for Printed Papers/Books

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (GSM)	1000.0

158

28907 (2021) - CUSTOM SPECIFICATION -IR STD. SPEC SR NO T-31-2021 FOR LADLE ANALYSIS [-]

CUSTOM SPECIFICATION -IR STD. SPEC SR NO T-31-2021 FOR LADLE ANALYSIS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3.1 (Carbon)	1000.0
4.3.1 (Manganese)	1000.0
4.3.1 (Silicon)	1000.0
4.3.1 (Sulphur)	1000.0
4.3.1 (Phosphorus)	1000.0

159

Customized Specification for Fleece Laminated Self adhesive SBS Modified membrane - Customized Specification for Fleece Laminated Self adhesive SBS Modified membrane [-]

Customized Specification for Fleece Laminated Self adhesive SBS Modified membrane

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Thickness)	1000.0
- (Pressure Head Test)	2000.0
- (Tensile Strength(Longitudinal direction))	1000.0
- (Tensile Strength(Transversal))	1000.0
- (Elongation at Break(Longitudinal))	1000.0
- (Elongation at Break(Transversal))	1000.0
- (Tear Strength(Longitudinal))	1000.0
- (Tear Strength(Transversal))	1000.0
- (Low temperature flexibility)	2000.0
- (Heat Resistance)	1000.0
- (Static Puncture Resistance)	1000.0
- (Softening Point of coating compound)	1500.0
- (Water absorption at 24 hours)	2000.0

160

Custom - Concrete - Hardened Concrete Physical & Chemical properties.

Hardened Concrete Physical & Chemical properties.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 (Test for compressive strength (3) [IS 516 (Part 4)], N/mm^2)	15000.0
- - (Test for Alkali content (3) [IS 4032 or relevant specification], %)	3000.0
- - (Test for Chloride Content (3) [ IS 4032 or relevant specification], %)	3000.0
-- (Test for sulphate content (3) {is 4032 or relevant specification], %)	3000.0
- - (Test for Sulphate Content [IS 4032 or relevant specification], %)	2000.0
- - (Test for Alkali content (2) [IS 4032 or relevant specification))	2000.0
- - (Test for Chloride Content (2) [IS 4032 or relevant specification], %)	2000.0
8 (Equivalent Cube Strength [IS 516 (Part 4)], in N/mm^2)	5000.0
- (Test for Alkali content [IS 4032 / IS 2386], %)	1000.0
- - (Test for Chloride Content [ IS 4032 or relevant IS], %)	1000.0
- - (Test for Sulphate content [IS 4032 or relevant specification], %)	1000.0
3 (Test for Carbonation [IS 516 (Part 5 / section 3)])	5000.0
8 (Test for compressive Strength (5) [IS 516 (Part 4)], in N/mm^2)	25000.0
- - (Test for Alkali content (5) [Is 4032 or relevant specification], %)	5000.0
- - (Test for Chloride Content (3) [ IS 4032 or relevant specification], %)	3000.0
- - (Test for Sulphate content (5) [IS 4032 or relevant specification])	5000.0
- - (Hydrostatic Pressure Test, Depth of penetration on RCC Grade Concrete.)	10000.0
- - (Hydrostatic Pressure Test, Depth of penetration on PQC Grade Concrete.)	10000.0
- - (Preparation of RCC Grade Concrete)	10000.0
- - (Preparation of PQC Grade Concrete)	10000.0

161

Customized Specification for Shore D hardness test - Customized Specification for Shore D hardness test [-]

Customized Specification for Shore D hardness test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Shore D harness)	1000.0

162

1834 (1984) - SPECIFICATION FOR HOT APPLIED SEALING COMPOUNDS FOR JOINTS IN CONCRETE

SPECIFICATION FOR HOT APPLIED SEALING COMPOUNDS FOR JOINTS IN CONCRETE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Pour Point)	1500.0
- (Flow Test)	1500.0
- (Penetration)	1500.0

163

Customized Specification for SHYLA TOTE LARGE AST - Customized Specification for SHYLA TOTE LARGE AST

Customized Specification for SHYLA TOTE LARGE AST

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Nomenclature)	500.0
- (Outer dimensions(cm.) 37.4x14.7x26.3(+/-5%))	500.0
- (Weight(Kg.) 0.60(+/-5%))	1000.0
- (Capacity(ltrs)4.67(+/-5%))	1000.0
- (Colour(assorted))	500.0
- (Active Ingredient(Synthetic fabric))	2000.0
- (Identification Mark/Marking)	500.0
- (Packing type and speciofication)	500.0

164

Customized specification for SAIMAA LG HZ TOTE - Customized specification for SAIMAA LCHZ TOTE

Customized specification for SAIMAA LCHZ TOTE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Nomenclature of the product)	500.0
- (Specification(cm.)45x15x25(+/-5%))	500.0
- (Weight(Kg.) 0.7(+/-6%))	1000.0
- (Colour (assorted))	500.0
- (Volume(ltrs) 10(+/-10%))	1000.0
- (Packing type and specification)	500.0
- (Identification Mark/Marking)	500.0

165

Customized Specification for LAVIE LADIES HANDBAG CROCO BURSA LG TOTE-NAVY - Customized Specification for LAVIE LADIES HANDBAG CROCO BURSA LG TOTE-NAVY

Customized Specification for LAVIE LADIES HANDBAG CROCO BURSA LG TOTE-NAVY

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Nomenclature)	500.0
- (Specification(cm.) 42x13x28 (+/-3))	500.0
- (Weight(Kg.) 0.70(+/-6%))	1000.0
- (Colour)	500.0
- (Volume(ltrs) 5 (+/-6%))	1000.0
- (Packing type and specification)	500.0
- (Identification Mark/Marking)	500.0

166

Customized Specification for NUWARE MICROWAVE SAFE DINNER SET - Customized Specification for NUWARE MICROWAVE SAFE DINNER SET

Customized Specification for NUWARE MICROWAVE SAFE DINNER SET

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Nomenclature)	500.0
- (Description)	500.0
- (Colour)	500.0
- (Packing Specification)	500.0
- (Identification Mark/Marking)	500.0
- (Active Ingredient)	2000.0

167

RDSO M&C/ PCN/ 100/ 2018 (2018) - Specification for Epoxy Cum Polyurethane Painting System (Two Pack) for the Exterior Painting of Railway Coaches

Specification for Epoxy Cum Polyurethane Painting System (Two Pack) for the Exterior Painting of Railway Coaches

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Chapter V (Table 1) (Abrasion resistance-1000 cycles)	3000.0
Chapter V (Table 1) (Humidity test.)	11000.0
Chapter V (Table 1) (Durability Tests : Accelerated weathering test)	110000.0
Chapter V (Table 1) (Accelerated Tests Resistance to solvents)	1500.0
Chapter V (Table 1) (Accelerated Tests Resistance to water)	1500.0
Chapter V (Table 1) (Accelerated Tests Resistance to oil)	1500.0
Chapter V (Table 1) (Accelerated Tests Resistance to 20% caustic potash (weight by volume))	1500.0
Chapter V (Table 1) (Accelerated Tests (a) Resistance to 30% Sulphuric acid (weight by volume))	1500.0
Chapter V (Table 1) (Gloss at 60 degree angle of incidence)	1200.0
Chapter V (Table 1) (Viscosity (Efflux time by Ford cup No. 4 ) at 27 degree C)	1200.0
Chapter V (Table 1) (Fineness of grind)	1200.0
Chapter V (Table 1) (Theoretical Spreading rate)	1200.0
Chapter V (Table 1) (Pot life(After induction time)ii) 40 ± 2 Deg C)	2000.0
Chapter V (Table 1) (Pot life (After induction time) at i) 27 ± 2 Deg C)	1500.0
Chapter V (Table 1) (Mass in Kg/10 litres)	1200.0
Chapter V (Table 1) (Keeping Properties for both the packs)	5000.0
Chapter V (Table 1) (Flash Point (b) Component B)	1200.0
Chapter V (Table 1) (Flash Point (a) Component A)	1200.0
Chapter V (Table 1) (Flexibility & Adhesion (6.25mm mandrel))	1200.0
Chapter V (Table 1) (Scratch hardness (1.5 Kg LOAD))	1200.0
Chapter V (Table 1) (Volume solids)	1200.0
Chapter V (Table 1) (Dry film thickness/Per coat)	1200.0
Chapter V (Table 1) (Colour)	1200.0
Chapter V (Table 1) (Finish)	1200.0
Chapter V (Table 1) (Consistency)	1200.0
Chapter IV / Table I (Drying time c) Hard Dry at 70 Deg C)	1200.0
Chapter V (Table 1) (Drying time b) Hard Dry)	1200.0
Chapter V (Table 1) (Drying time a) Surface Dry)	1200.0
Chapter V (Table 1) (poly isocyanate, in hardener)	3000.0

168

BSEN 13348 (2016) - Copper and Copper Alloy - Seamless Round Copper Tube for Medical Gases or vacuum

Copper and Copper Alloy - Seamless Round Copper Tube for Medical Gases or vacuum

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.3 (Dimension - Outer Diameter mm, in accordanc e with BS EN 13348 (2016) Table 2, 3 and 4)	1000.0
6.3 (Dimension - Thickness of the Tube in mm in accordance with BS EN 13348(2016) Table 2, 3 and 4)	1000.0
6.2 (Tensile Strength)	2000.0
6.2 (Elongation)	1000.0
6.2 (Hardness)	2000.0
8.5 (Bending Test)	1000.0
8.6 (Drift Expansion test)	2000.0
6.1 (Cu + Ag)	4000.0
6.1 (Phosphorus (% by mass))	1000.0
6.1 (Copper (% by mass))	2000.0

169

IS 8887 (2004) - Bitumen Emulsion for Roads (Cationic Type)

Bitumen Emulsion for Roads (Cationic Type)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 and 6.2 (Viscosity by say bolt viscometer)	1000.0
4.2 and 6.2 (Solubility in Trichloroethylene)	1000.0
4.2 an 6.2 (Residue by Evaporation)	1500.0

170

IS 14223 (Part 1):2023 - Polished Building Stones —Specification (Part 1-Granite and Similar Stones)

Polished Building Stones —Specification (Part 1-Granite and Similar Stones)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5,Table 1-(i) (Specific gravity ( as per IS 1124))	1000.0
5,Table-1(ii) (Water absorption (as per IS 1124))	1000.0
5,Table-1(iii) (Compressive strength, in N/mm2 (as per IS 1121 (Part 1)))	3000.0
5,Table-1(vi) (Hardness, in Mohs (as per IS 13630 (Part 13)))	2000.0
5,Table-1(x) (Resistance to wear- a)Average b)Individual maximum, in mm (as per IS 1706))	4000.0
custom (Moisture content (%))	500.0
custom (Dry density)	1000.0
custom (Flexural strength)	3000.0
custom (Porosity)	1000.0

171

Custom specification- Bipolar for metro rail (general chemical) - Custom specification- Bipolar for metro rail (general chemical)

Custom specification- Bipolar for metro rail (general chemical)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Appearance)	500.0
- (Odour)	500.0
- (Skin Irritation)	500.0
- (pH Value)	1000.0
- (Viscosity by Flow cup)	1000.0
- (Accelerated Corrosion test ( For 21 Hours) with raw water)	1500.0
- (Accelerated Corrosion (for 21 hours) with Bipolar)	1500.0
- (Specific Gravity)	1000.0

172

IS 8986 (2022) (2022) - Hexagonal Integral Drill Steel and Extension Rods and Hollow Round Drill Steel in Bar Form — Dimensions (Second Revision)

Hexagonal Integral Drill Steel and Extension Rods and Hollow Round Drill Steel in Bar Form — Dimensions (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Dimension - Hexagonal Integral Drill Steel and Extension Rods in mm Clause 2.1 and Table 1 of IS 8986 or any other relevant National & International Standard Specified)	1000.0
2 (Dimension -Hollow Round Drill Steel in Bar Form for Extension Rods, in mm, Clause 2.2, Table 2 of IS 8986 or any other national or International Stanard specified)	1000.0
2 (Mass per Meter in Kg/M as per Table 1 or 2 of IS 8986 or any other National or International Standard specified.)	1000.0
0 (Rockwell Hardness Test in HRC)	2000.0
0 (Mechanical Properties - Tensile Strength, Yield Strength and % of Elongation as per IS 1608 Prt-1 or ASTM E8 or any other relevant National or International specification.)	4000.0
2 (Sectional Area in mm2 as per IS 8986 Clause 2 Table 1 /Table 2)	1000.0
0 (Chemical Composition in mass% by OES method or any other National or International product specification specified test method.)	3500.0

173

IS 17044 (2018) - Intumescent fire retardant paint (Water Based) - Specification

Intumescent fire retardant paint (Water Based) - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Intumescent fire retardant paint (Water Based) - Specification (Please refer to the annexure for the test result)	10000.0

174

IS 5758 (2020) - Precast Concrete Kerbs, Channels, Edgings, Quadrants and Gutter Aprons

Precast Concrete Kerbs, Channels, Edgings, Quadrants and Gutter Aprons

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2 (Dimensions, Overall Length, in mm)	500.0
9.2 (Dimensions, Overall Height, in mm)	500.0
9.2 (Overall Thickness, in mm)	500.0
9.3 (Bending Strength, N/mm^2)	4000.0
9.4 (Water Absorption, in %)	2000.0
4.2 (Shape and Profile)	1000.0

175

IS 15961 (2012) - Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain)

Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Triple Spot Coating Mass)	2000.0

176

IS 15965 : 2012 (2012) - Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Total Coated Thickness (As received condition), mm)	1000.0
8 (Tensile Strength (As per IS 15961), MPa)	1000.0
8 (Yield Strength (As per IS 15961), MPa)	1000.0
8 (% Elongation (As per IS 15961), %)	1000.0
7.1 (Mass of Coating (Both sides), g/m²)	2000.0
5 (Chemical composition (As per IS 513), % by mass)	2500.0
1 (Composition of AZ Coating Material in %)	3000.0

177

Customized Specification for Plastic Bottle with cap - Customized Specification for Plastic Bottle with cap

Customized Specification for Plastic Bottle with cap

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Identification of Plastic bottle body by FTIR)	2000.0
- (Identification of plastic cap by FTIR)	2000.0

178

- (2025) - Customize General chemical specifical NTH (WR)

Customize General chemical specifical NTH (WR)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Appearance)	500.0
- (Specific gravity)	1000.0
- (Releasing Properties)	3000.0
- (Flash Point by COC)	1000.0
- (Fire Point by COC)	1000.0
- (Aluminium Reactivity at 60 deg. C for 72 hours)	1000.0
- (Effect on Wooden Ply at 60 deg C. for 72 hours)	1000.0
- (Viscosity by Flow Cup)	1000.0

179

16720 (2018) - Pulverized Fuel Ash - Cement Bricks

Pulverized Fuel Ash - Cement Bricks

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (General)	500.0
8.2 (Dimension, Length, in mm)	500.0
8.2 (Dimensions, Width)	500.0
8.2 (Dimensions, Thickness, in mm)	500.0
8.3 (Density, in kg/m^3)	1000.0
8.4 (Compressive Strength, in N/mm^2)	2000.0
8.5 (Drying Shrinkage, in %)	2000.0
8.6 (Water Absorption Test)	1000.0

180

IS 18387 (2023) - Gypsum Ceiling Tiles

Gypsum Ceiling Tiles

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1.1 (Dimensions and Tolerances on size, Length in mm)	500.0
7.1.1 (Dimensions and Tolerances on Size, Width)	500.0
7.1.2 (Dimensions and Tolerances on Edges Profile)	500.0
7.2.2 (Tolerances on Squareness of Edges,)	500.0
7.3 (Density, in kg/m^3)	1000.0
7.4 (Flexural Breaking Strength (Length wise), in N)	2000.0
7.4 (Flexural Breaking Strength (Across the length), in N)	2000.0
7.5 (Water Absorption, in %)	1000.0
7.8 (Humidified Deflection, in mm)	5000.0

First
Prev
5
6
7
8
Next
Last