NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum@nth.gov.in

Scope List

Reset

785 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

IS 4270 (2001) - Steel tubes used for water wells specification (Third Revision)

Steel tubes used for water wells specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Chemical analysis)	2500.0
9 (Outside diameter)	3000.0
6.2 (Flattening)	1000.0
6.1 (Tensile test)	3000.0
7 (Weight in kg/m)	1000.0
7 (Length)	250.0
7 (Thickness)	250.0
7 (Outside diameter)	250.0
14 (Visual examination)	1000.0
5.2 (Sulphur)	1250.0
6.2 (Flattening Test)	1500.0
6.1 (% Elongation)	1000.0
6.1 (Tensile Strength)	1000.0
6.1 (Yield Strength)	1000.0
7 (Thickness)	1000.0
14 (Workmanship)	1000.0
5.2 (Phosphorus)	1250.0

BS EN 12467 (2012) - Fibre - cement flat sheets - Product specification and test method.

Fibre - cement flat sheets - Product specification and test method.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.3.2 (Nominal Length, in mm)	500.0
5.3.2 (Nominal Width, mm)	500.0
503.3 (Thickness, in mm)	1000.0
5.3.4.1 (Tolerance on length, in mm)	500.0
5.3.4.1 (Tolerance in Width, in mm)	500.0
5.3.4.2 (Tolerance on thickness, in mm or %)	500.0
5.3.5.1 (Straightness of Edges, in %)	500.0
5.3.5.2 (Squareness of edges, in mm/m)	500.0
5.4.2 (Apparent Density)	1000.0
5.4.3 (Moisture Movement, in %)	2000.0
5.4.4 (Bending Strength (MOR) in Ambient Laboratory condition, in MPa.)	4000.0
5.4.4 (Bending Strength (MoR) in Wet Condition, MPa)	8000.0
5.4.5 (Water Impermeability,)	4000.0
5.5.2 (Freeze Thaw Test)	25000.0
5.5.4 (Warm Water Durability test)	25000.0
5.5.5 (Soak Dry Durability Test)	25000.0

Custom - Concrete - Custom Physical Tests on hardened Concrete

Custom Physical Tests on hardened Concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- - (Compressive Strength , MPa)	1200.0
- - (Water Absorption)	1000.0
- - (Water Absorption after 24 hours)	1000.0
- - (Density of concrete)	1000.0

NTH/WR/RPPT/Inspection of Paper - NTH/WR/RPPT/Inspection of Paper

NTH/WR/RPPT/Inspection of Paper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Paper Inspection Report)	30798.0

NTH/WR/RPPT/2025/Inspection of papers - Inspection of Papers [-]

Inspection of Papers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Firms requirements)	115000.0

NTH/NR/RPPT/Paper Inspection (2024) - Inspection of Papers

Inspection of Papers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's Requirements (Inspection Report)	37260.0

Custom - Cement Sand mix. - Cement - Sand Mix. [- -]

Cement - Sand Mix.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
-- (Sand Content and cement content, %)	3000.0
- - (Visual Examination)	2000.0
- - (Physical Properties)	2000.0
- - (Chemical composition of cement)	5000.0

Custom (0) - Cement Sand ratio

Cement Sand ratio

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1. (Cement sand ratio)	5000.0

IS 2347 (2023) - Domestic pressure cooker - Specification (Sixth Revision)

Domestic pressure cooker - Specification (Sixth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Capacity)	500.0
6.1.1 (Vent pipe inside diameter)	500.0
8.1 (Air Pressure of domestic pressure cooker)	1000.0
8.2 (Proof Pressure of domestic pressure cooker)	2000.0
8.3 (Operating pressure for Pressure Regulating Device)	1000.0
8.4.1 Annex-H cl. No. H-1.1 (Operating pressure of Safety Pressure Relief Device for destructible device)	1000.0
8.6.1 (Removal of Lid under Pressure (For Outer Lid Cooker))	1000.0
8.6.2 (Removal of Lid under Pressure (For Inner Lid Cooker))	1000.0
8.5 (Bursting Pressure Test)	3000.0
5.3 (Performance Test on Gasket)	1000.0
7.4 Annex-E cl. No. E-2 (Coating thickness for body)	2000.0
7.4 Annex-E cl. No. E-3 (Abrasion resistance for body)	500.0
7.4 Annex-E cl. No. E-4 (Micro Vickers Hardness for body)	2000.0
8.9 (Test for Induction Bottom)	5000.0
TDS 1 (Weight, kg.)	-
5.1 (Chemical Composition, % by mass.)	6000.0
TDS-2 (Overall Dimension- Thickness, mm.)	-
7.4 Annex-E cl. No. E-2 (Coating thickness for lid)	2000.0
7.4 Annex-E cl. No. E-3 (Abrasion resistance for lid)	500.0
7.4 Annex-E cl. No. E-4 (Micro Vickers Hardness for lid)	2000.0
5.4 (Performance test for pressure cooker handle as per IS 13395)	11000.0
0 (Test Result as per Annexure.)	20000.0
8.4.1 Annex-H cl. No. H-1.2 (Operating pressure of Safety Pressure Relief Device for Gasket Release System.)	1000.0
0 (CSD - Pressure Cooker -All Possible Test as per TDS and IS 2347)	5000.0

IS 14255 (1995) - "AERIAL BUNCHED CABLES-FOR WORKING VOLTAGES UPTO AND INCLUDING 11OOVOLTS "

"AERIAL BUNCHED CABLES-FOR WORKING VOLTAGES UPTO AND INCLUDING 11OOVOLTS "

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 (Type tests)	20000.0
10.2 (Acceptance tests)	10000.0

14255 (1995) - Aerial Bunched Cables for working voltages up to and including 1100 Volts-Reaffirmed 2020 specification

Aerial Bunched Cables for working voltages up to and including 1100 Volts-Reaffirmed 2020 specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

IS 10322 : PART 5 : SEC 3 (2012) - Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Provision for earthing)	1200.0
12 (Protection against Electric Shock)	1200.0

IS 733 (1983 RA 2022) - SPECIFICATION FOR WROUGHT ALUMINIUM AND ALUMINIUM ALLOY BARS, RODS AND SECTIONS (FOR GENERAL ENGINEERING PURPOSES)

SPECIFICATION FOR WROUGHT ALUMINIUM AND ALUMINIUM ALLOY BARS, RODS AND SECTIONS (FOR GENERAL ENGINEERING PURPOSES)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1.1 a Chemical composition (Aluminium (as Al )content,% by mass)	3000.0
5.1.1 b Chemical composition (Copper (as Cu)content,% by mass)	500.0
5.1.1 C Chemical composition (Magnesium(as Mg ) content,% by mass)	500.0
5.1.1 d Chemical composition (Silicon (as Si) content,% by mass)	500.0
5.1.1 e Chemical composition (Iron (as Fe) content,% by mass)	500.0
5.1.1 f Chemical composition (Manganese (as Mn) content,% by mass)	500.0
5.1.1 g Chemical composition (Zinc (as Zn ) content,% by mass)	500.0
5.1.1 h Chemical composition (Titanium (as Ti) content,% by mass)	500.0
5.1.1 i Chemical composition (Chromium (as Cr) content,% by mass)	500.0
5.1.1 j Chemical composition (Vanadium (as V) content,% by mass)	500.0
7 (Dimension)	1000.0
9.1 (Tensile Strenth)	2000.0
9.1 (0.2% Proof Stress)	1000.0
9.1 (Elongation)	1000.0
5 (Chemical composition, % by mass)	6000.0
0 (Anodic Coating)	2000.0
0 (Weight, kg)	1000.0

Shore D hardness - Shore D hardness

Shore D hardness

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Shore D hardness)	1000.0

4021 (1995 Reaf. 2022) - Timber Door, Window and Ventilator Frames

Timber Door, Window and Ventilator Frames

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Specific Gravity / Density, g/cc (kg/cum))	1000.0
4.1.2 (Moisture Content, %)	1000.0
6.2 (Size and Type)	1000.0
6.1 (Dimensions of Frame and Tolerances, in mm)	1000.0

Manufacturer/Customer's specifications & GTP - Manufacturer/Customer's specifications & GTP

Manufacturer/Customer's specifications & GTP

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.00 (Conformity Tests for Battery operated platform truck as per IS: 10311-1982)	30000.0
1.00 (AC High Voltage Test at power frequency)	5000.0
1.00 (Neutral Grounding Resistance (Grid Resistance)-03 Resistors)	30000.0
1.00 (Neutral Grounding Resistance (Grid Resistance) Single Resistor)	10000.0
1.00 (Neutral Grounding Resistance (Grid Resistance) Two Resistor)	20000.0

IS 650:1991 - Standard sand for testing cement

Standard sand for testing cement

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Size-Sieve analysis -Particle size distribution)	2000.0
5.1 (The loss of mass -on extraction with hot HCl)	1200.0
5.1 (Organic Impurities)	1000.0

IS 8662 (2004) - Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision)

Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.6.xiii (Keeping properties)	5000.0
6.6.xii (Accelerated storage stability test, at 60 degC, 96 h)	3000.0
6.6.xi.b (Phthalic anhydride content of non-volatile vehicle)	3000.0
6.6.xi.a (Volume solids)	3000.0
6.6.x (Flash point)	1500.0
6.6.ix (Flexibility and adhesion)	1200.0
6.6.viii (Scratch hardness after 48 h air drying (1 000 g weight))	1500.0
6.6.vii (Water content (if suspected to be present) - IS 101 (Part 2/Sec 1))	1200.0
6.6.vi (Colour)	1200.0
6.6.v (Fineness of grind,)	1200.0
6.6.iv.b (Gloss , 60 deg)	1500.0
6.6.iv.a (Fnish)	1200.0
6.6.iii.d (Drying time Tack Free)	1200.0
6.6.iii.c (Hard dry at 70 DegC with 15 min flash- off time)	1200.0
6.6.iii.a (Drying time Surface Dry)	1200.0
6.6.ii (Mass, in kg/101itres)	1500.0
6.6.i.b (Viscosity byFord cup No. 4)	1200.0
6.6.i.a (Consistency)	1200.0
6.5 (Resistance to Alkali (for Finishing Only)	1500.0
6.4 (Resistance to Acid (for Finishing Only))	1500.0
6.3 (Durability( Normal Outdoor Exposer))	10000.0
6.2.6 (Application Properties)	1200.0
6.2.5 (Thinning Properties)	1200.0
6.2.4 (Skin Formation)	1200.0
6.2.3 (Freedom from Coarse Particles)	1200.0
6.2 (Condition in Container)	1200.0
CLAUSE-4.5.2,Table-1 (Dry Film Thickness(DFT))	1500.0
6.7 (Pigment content)	1000.0
Cl.6.8 Table 2 (Test Result, General parameters only- (Please see Annexure))	10000.0
ICF/MD/Specn. 045 (Durability test (QUV Accelerated Weathering, 250 Hrs), Accelerated Storage Test, Wet abrasion test)	20000.0
Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision) (Keeping Properties 12 months)	5000.0

General RDSO Specification NTH WR - General RDSO Specification NTH WR [-]

General RDSO Specification NTH WR

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
General RDSO Specification NTH WR (Painting system of FRP Components- MTDS: 118 REV 01: - 2-Component polyurethane Base Primer)	15900.0
General specification RDSO (Painting system of FRP Components- MTDS: 118 REV 01: - 2-Component polyurethane Base Primer for 12 months Keeping properties)	10000.0

NTH(WR)/MECH/CUSTOM/029 (2025) - Student Bench - Specification for Student Bench

Specification for Student Bench

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Type of Seating, Suitable for age group, Number of Seating Capacity Desk with Self (Under Storage) Height, Width and Length MS Pipe Size, MS Pipe gauge (Thickness), MS Pipe Frame size Supportign MS Pipe and Supporting Angle size BEJ Type SAG Border Patti Writing Pad Bag Bad Back Hight, Back Length Color of Buch Fitting Type Finishing)	6500.0

NTH(WR)/MECH/CUSTOM/028 (2025) -Breathing Air Compressor (2025) - High Pressure, 3 Stage, Reciprocating type, Air cooled, Oil Lubricated Breathing Air Compressor

High Pressure, 3 Stage, Reciprocating type, Air cooled, Oil Lubricated Breathing Air Compressor

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Acceptance Test -Customer Specification: (Ref, Stanadrd IS 15879:2009 and Customer Acceptance Test Procedure Annexure-A , B & C) 1. Specification Check - Scope Verification and Air flow diagram verification (As per sketch) 2. Weights and Measures 3. Records of Test Run Parameters- Medium, Intake pressure, Final discharge Pressure, 3. a.Air Leak test- Leak detector spray Method 3.b. Noise / sound level HP air compressor- ≤85 db(A) at a distance of 1meter 3.c Calculated capacity LPM - Customer Specified Method 4. Record of Functional Test - Safety Relief Valve ( 330 bar +/- 10% and 225 bar +/- 10%), Functioning of Condensate drain)	28000.0
2 (Acceptance Test Procure reference with IS 15879:2009 Verification of material of construction - Method of Checking Magnetic or Non Magnetic Type Crankcase, Cylinders,Cylinder Heads, Crankshaft, Connecting rods, Pistons, Valves and Flywheel)	8000.0

None - Indelible Marker Pen

Indelible Marker Pen

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Custom specification for Indelible Marker Pen (Please refer annexure for the test result)	7000.0

RDSO SPECIFICATION No. M&C/ PCN/ 100/ 2018 (2018) - SPECIFICATION FOR EPOXY CUM POLYURETHANE PAINTING SYSTEM (TWO PACK) FOR THE EXTERIOR PAINTING OF RAILWAY COACHES, DIESEL AND ELECTRIC LOCOMOTIVES AND OTHER INDUSTRIAL APPLICATIONS

SPECIFICATION FOR EPOXY CUM POLYURETHANE PAINTING SYSTEM (TWO PACK) FOR THE EXTERIOR PAINTING OF RAILWAY COACHES, DIESEL AND ELECTRIC LOCOMOTIVES AND OTHER INDUSTRIAL APPLICATIONS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

Asian Paints Customs Specification - Asian Paints Customs Specification [-]

Asian Paints Customs Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Shore A Hardness)	1000.0
- (Shore D Hardness)	1000.0
- (Tensile Strength)	1500.0
- (Elongation)	1500.0
- (Static Crack Bridging facility)	2000.0
- (Dynamic Crack Bridging)	2000.0
- (Puncture Resistance)	2000.0
- (DFT)	1200.0
- (Impact Resistance)	1500.0
- (Tear Resistance)	3000.0
- (Taber Resistance (1000 cycles))	3000.0
- (Pull off adhesion over concrete)	5000.0
- (Resistance to Hydrostatic Pressure)	10000.0
- (Water vapour Transmission)	5000.0
- (Chemical Resistance)	4000.0
- (VOC)	2000.0
- (Density)	1000.0
- (Solid content)	2000.0
- (Depth of Water Penetration)	5000.0
- (Viscosity)	2000.0
- (Alkaline resistance test)	2000.0
- (Tensile Strength after immersion in alkaline)	1500.0
- (Elongation after immersion in alkaline)	1500.0
- (Compressive Strength)	4000.0
- (Flexural Strength)	3000.0
- (Slant Shear /Bond Strength)	4000.0
- (Adhesion-Pull Off)	2000.0
- (Epoxy Mortal Values(ratio 1:1:10) a)Compressive Strength b)Flexural Strength c)Tensile Strength d)Gel time)	20000.0
- (Modulus of Elasticity)	2000.0
- (Structural adhesive Properties: a)Compressive Strength b)Shrinkage)	8000.0
- (Adhesion with steel surface)	2000.0
- (Salt Spray Test)	5000.0
- (AC Impedence)	2000.0
- (Abrasion Resistance)	4000.0
- (Permeability test)	3000.0
- (Tensile Modulus(Modulus of Elasticity))	3000.0

IS 8811 (1998) - Method for emission spectrometric analysis of plain carbon and low alloy steels point to plane technique (First Revision)

Method for emission spectrometric analysis of plain carbon and low alloy steels point to plane technique (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Aluminium content (as Al) % by mass)	500.0
2 (Carbon content (as C) % by mass)	500.0
3 (Chromium content (as Cr) % by mass)	500.0
4 (Cobalt content (as Co) % by mass)	500.0
5 (Copper content (as Cu) % by mass)	500.0
6 (Manganese content (as Mn) % by mass)	500.0
7 (Molybdenum content (as Mo) % by mass)	500.0
8 (Nickel content (as Ni) % by mass)	500.0
9 (Phosphorus content (as P) % by mass)	500.0
10 (Silicon content (as Si) % by mass)	500.0
11 (Sulphur content (as S) % by mass)	500.0
12 (Titanium content (as Ti) % by mass)	500.0
13 (Incidental element Vanadium(as V) content % by mass)	500.0
14 (Incidental element Aluminium content (as Al) % by mass)	500.0
15 (Incidental element Molybdenum content (as Mo) % by mass)	500.0
16 (Incidental element Nitrogen as N content %by mass)	500.0

Valve Testing as per Test request - Valve Testing as per Test request

Valve Testing as per Test request

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Hydrostatic Test of Body)	5000.0
0 (Hydrostatic Test of Seat)	2500.0
0 (Hydrostatic Test of Disc Strength)	2500.0
0 (Measurement of Dimensions)	2000.0
0 (Chemical composition, % by Mass)	5000.0
0 (Lightening Impulse Test)	50000.0

IS 5312 : Part 1 (2004) - Swing Check Type Reflux (Non-Return] Valves for Water Works Purposes - Part 1 : Single-Door Pattern

Swing Check Type Reflux (Non-Return] Valves for Water Works Purposes - Part 1 : Single-Door Pattern

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Chemical Analysis)	3000.0
8 (Hydrostatic Test)	2500.0
6.2 (Dimensions)	1000.0
8 (Hydrostatic Test)	2500.0

SmartCare EPDM - SmartCare EPDM [-]

SmartCare EPDM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Thickness)	1000.0
- (Tensile Strength)	1500.0
- (Elongation)	1500.0
- (Shore D hardness)	1000.0
- (Tear Strength)	2000.0
- (Mass per Unit area)	1000.0
- (Recovery)	2000.0
- (Factory Seam Strength)	2000.0
- (Water absorption)	2000.0
- (Linear Dimension change)	2000.0

SmartCare SBS - SmartCare SBS

SmartCare SBS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Thickness)	1000.0
- (Thickness of HDPE lining)	1000.0
- (Tensile Strength Longitudinal)	1500.0
- (Tensile Strength Transverse)	1500.0
- (Elongation Longitudinal)	1500.0
- (Elongation Transverse)	1500.0
- (Tensile Strength Longitudinal)	1500.0
- (Tensile Strength Transverse)	1500.0
- (Elongation Longitudinal)	1500.0
- (Elongation Transverse)	1500.0
- (Tear Resistance)	2000.0
- (Puncture Resistance)	2000.0
- (Low temperature flexibility)	2000.0
- (Resistance to Hydrostatic Pressure)	5000.0
- (Water absorption)	2000.0
- (Water vapour Transmission rate)	5000.0
- (Heat resistance@ 70 deg. C)	2000.0
- (Lap Peel Adhesion)	2000.0
- (Peel Adhesion with Primed Concrete)	2000.0
- (Softening Point)	1500.0
- (Penetration @ 25deg. C ,100 gms,5 sec.)	1500.0

Smartcare PVC - Smartcare PVC [-]

Smartcare PVC

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Thickness)	1000.0
- (Tensile Strength Longitudinal)	1500.0
- (Tensile Strength Transverse)	1500.0
- (Elongation Longitudinal)	1500.0
- (Elongation Transverse)	1500.0
- (Static Puncture Resistance)	2000.0
- (Low Temperature Flexibility)	2000.0
- (Resistance to hydrostatic Pressure)	5000.0
- (Resistance to Joint N/50 mm.)	2000.0
- (Resistance to acid/alkali)	3000.0

First
Prev
1
2
3
4
Next
Last