| 31 |
IS 6603 (2024) - Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars — Specification (2nd Revision) |
Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars — Specification (2nd Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7 (Chemical Composition-The ladle analysis of steel, when carried out either by the methods specified in relevant parts of IS 228 or any other established international instrumental/chemical method) |
5000.0 |
|
| 9.0 Mechancial Properites (The tensile test ( Tensile Stregth, 0.2% Proof/Yield Stress, % of Elongation ) shall be carried out in accordance with IS 1608 (Part 1)) |
3000.0 |
|
| 9.0 Mechancial Properties (Hardness shall be determined in accordance with IS 1500 (Part 1), IS 1501 (Part 1) or IS 1586
(Part 1).) |
2000.0 |
|
| 9.0 Mechanical Properties (Charpy impact test shall be carried out in accordance with IS 1757 (Part 1).) |
5000.0 |
|
| 12 (Dimesnion Measurment in mm
dimensional tolerances for the bars and flats shall be as laid down in Table 26 to Table 36 given at Annex C of IS 6603) |
1000.0 |
|
| 14 (Corrosion Resistance Test - The material shall be tested for corrosion resistance as per IS 10461 (Part 1) or ISO 3651 (Part 2) or any other method) |
10000.0 |
|
| 6 (Freedom From Defects - Visual Examination as per IS 6603 Cl.6.1 & 6.2) |
1000.0 |
|
|
| 32 |
ASME Section IX (2019) - 2019 Boiler and Pressure Vessel Code |
2019 Boiler and Pressure Vessel Code |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Tensile Strength in Longitudinal direction as per ASTM D 5147) |
2000.0 |
|
|
| 33 |
ASME ASME Section IX (2021) - Preparation of welding procedure specification (WPS) as per ASME Section IX |
Preparation of welding procedure specification (WPS) as per ASME Section IX |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Tensile Strength in Longitudinal direction as per ASTM D 5147) |
2000.0 |
|
| 8 (Chemical composition) |
5000.0 |
|
|
| 34 |
IS 17545:2021 - WHITE CEMENT BASED POLYMERIC PUTTY |
WHITE CEMENT BASED POLYMERIC PUTTY |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.5, Table 1, (iv) (Polymer content(based on loss on ignition)-Annex E) |
1000.0 |
|
| 4.5, Table 1, (vi) (Cement content-Annex B of IS 5410) |
1000.0 |
|
| 4.4 (Lead Restriction-ASTM D3335-85a.) |
1000.0 |
|
| 4.1 (Form and Condition) |
500.0 |
|
| 4.3 (Consistency) |
500.0 |
|
| 4.5 Table, 1, (i) (Average Tensile adhesion strength@ 14days-Annex B) |
2000.0 |
|
| 4.5, Table 1, (ii) (Water retentivity-Annex C) |
1000.0 |
|
| 4.5, Table 1, (iii) (Initial Setting time-Annex D) |
250.0 |
|
| 4.5, Table 1, (v) (Degree of whiteness-Annex B of IS 8042) |
2000.0 |
|
| 4.6 Table 2 (28 days Compressive strength-IS 4031(6)) |
1000.0 |
|
| 4.5, Table 1, (iii) (Final Setting time-Annex D) |
250.0 |
|
|
| 35 |
IS 9417 (2018) - Welding of high strength steel bars for reinforced concrete construction - Recommendations (Second Revision) |
Welding of high strength steel bars for reinforced concrete construction - Recommendations (Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 13.1.1 (Tensile Test) |
3000.0 |
|
| 13.1.2 (Mechanical Bend Test) |
1000.0 |
|
|
| 36 |
IS 13620 (1993) - Fusion Bonded Epoxy Coated Reinforcing Bars - |
Fusion Bonded Epoxy Coated Reinforcing Bars - |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7.1 (Coating Thickness) |
1500.0 |
|
| 8 (Chemical composition) |
5000.0 |
|
|
| 37 |
CUS/SR/NDT/CUSTOM/001 (2024) - Welding wire |
Welding wire |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Size of Wire) |
1000.0 |
|
| 2.0 (Type of Wire) |
2000.0 |
|
| 8 (Chemical composition) |
5000.0 |
|
|
| 38 |
Custom-7-ER-LM - Galvanized Steel Rope Net Wire |
Galvanized Steel Rope Net Wire |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7 (Tensile Strength of Element wire) |
3000.0 |
|
| 1 (Breaking Force of Rope) |
3000.0 |
|
| 8 (Chemical composition) |
5000.0 |
|
|
| 39 |
ILC Of paper - Customized Specification for the ILC of paper |
Customized Specification for the ILC of paper |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 40 |
IS 8662 (2004) - Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision) |
Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.6.xi.a (Volume solids) |
3000.0 |
|
| CLAUSE-4.5.2,Table-1 (Dry Film Thickness(DFT)) |
1500.0 |
|
| 6.7 (Pigment content) |
1000.0 |
|
| 6.6.iii.a (Drying time Surface Dry) |
1200.0 |
|
| 6.6.iii.b (Drying time Hard Dry) |
1200.0 |
|
| 6.6.iii.d (Drying time Tack Free) |
1200.0 |
|
| 6.6.iii.c (Hard dry at 70 DegC
with 15 min flash-
off time) |
1200.0 |
|
| 6.6.ii (Mass, in kg/101itres) |
1500.0 |
|
| 6.6.viii (Scratch hardness after 48 h air
drying (1 000 g weight)) |
1500.0 |
|
|
| 41 |
IS 1367 : Part 3 (2017) - Technical Supply Conditions for Threaded Steel Fasteners Part 3 Mechanical Properties of Fasteners Made of Carbon Steel and Bolts, Screws and Studs |
Technical Supply Conditions for Threaded Steel Fasteners Part 3 Mechanical Properties of Fasteners Made of Carbon Steel and Bolts, Screws and Studs |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6 (Chemical Composition, % by mass) |
2500.0 |
|
| 7 (Mechanical and physical properties (Hardness,Rockwell C scale)) |
2000.0 |
|
| 7 (Mechanical and physical properties (Proof load test)) |
1000.0 |
|
| 7 (Mechanical and physical properties (ultimate tensile load)) |
2000.0 |
|
| 2 (Dimensions) |
1000.0 |
|
| 9.1.4 (Wedge Load test as per IS 1367 Part 3) |
3000.0 |
|
|
| 42 |
IS 3757 (1985) - Specification for high strength structural bolts (Second Revision) |
Specification for high strength structural bolts (Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 2 (Dimension (Length of bolt)) |
200.0 |
|
| 2 (Dimension (Shank Diameter)) |
200.0 |
|
| 2 (Dimension (Width across the flat)) |
400.0 |
|
| 2 (Dimension (Width across the edge)) |
400.0 |
|
| 2 (Dimension (Height of the head)) |
400.0 |
|
| 4 (Mechanical Properties(Tensile Strength) as per IS 1367(Part-3):2017 Clause No.- 7) |
3000.0 |
|
| 4 (Mechanical Properties(Proof Load Test) as per IS 1367(Part-3):2017 Clause No.- 7) |
2000.0 |
|
| 4 (Mechanical Properties(Ultimate Tensile Load) as per IS 1367(Part-3):2017 Clause No.- 7) |
2000.0 |
|
| 4 (Mechanical Properties(Vickers Hardness ) as per IS 1367(Part-3):2017 Clause No.- 7) |
2000.0 |
|
| 4 (Mechanical Properties( Rockwell Hardness Scale- C) as per IS 1367(Part-3):2017 Clause No.- 7) |
2000.0 |
|
| 4 (Carbon) |
500.0 |
|
| 4 (Sulfur) |
500.0 |
|
| 4 (Phosphorus) |
500.0 |
|
| 4 (Boron) |
500.0 |
|
|
| 43 |
IS 6162 (Part-1):1971,Reaffirmed 2018 - Specification for Paper-Covered Aluminium Conductors |
Specification for Paper-Covered Aluminium Conductors |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Tests (i)Measurement of diameter of conductor,
ii)Measurement of overall diameter,
iii) Measurement of increase in diameter due to covering.) |
3000.0 |
|
|
| 44 |
IS 10500 - Potability Test |
Potability Test |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Fluoride) |
500.0 |
|
| 2 (pH Value) |
200.0 |
|
| 3 (Chloride) |
300.0 |
|
| 4 (Total Dissolved Solids) |
300.0 |
|
| 5 (Turbidity) |
200.0 |
|
| 6 (Calcium) |
500.0 |
|
| 7 (Magnesium) |
500.0 |
|
| 8 (Sulphate) |
400.0 |
|
| 9 (Nitrate) |
400.0 |
|
| 10 (Total Hardness) |
300.0 |
|
| 11 (Total Alkalinity) |
400.0 |
|
| 12 (E. Coli) |
500.0 |
|
| 13 (Total Coliform) |
500.0 |
|
|
| 45 |
13778 (2012) - WINDING WIRES |
WINDING WIRES |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| PART 2 (Determination of Dimensions) |
2000.0 |
|
| PART 3 (Mechanical Properties) |
3000.0 |
|
| PART 5 (Electrical Properties-Electrical Resistance) |
5000.0 |
|
|
| 46 |
Custom Specification-NWR - Hardened Concrete |
Hardened Concrete |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Cement Content) |
2500.0 |
|
| 2 (Silt Content) |
1000.0 |
|
| 3 (pH Value) |
500.0 |
|
| 4 (Alkali Aggregate Reactivity) |
1000.0 |
|
|
| 47 |
IS 278 (2009) - Galvanized steel barbed wire for fencing - Specification (Fourth Revision) |
Galvanized steel barbed wire for fencing - Specification (Fourth Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 12.1 (Breaking Load of Completed Barbed Wire) |
1000.0 |
|
| 12.1 (Tensile Strength of Line Wire) |
1000.0 |
|
| 12.3 (Ductility) |
1000.0 |
|
| 12.2.1 (Zinc Coating of Line wire) |
2000.0 |
|
| 5 (Dimension/ Sizes) |
1000.0 |
|
| 9 (Freedom from Defects) |
500.0 |
|
| 12.2.2 (Zinc Coating of Point wire) |
2000.0 |
|
|
| 48 |
IS 2141 (2000) - Hot dip galvanized stay strand - Specification (Fourth Revision) |
Hot dip galvanized stay strand - Specification (Fourth Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4 (Sulphur) |
500.0 |
|
| 4 (Phosphorus) |
500.0 |
|
| 6.2 (Breaking Force of Single Wire) |
2000.0 |
|
| 7 (Freedom from defect) |
1000.0 |
|
| 8.1 (Wrapping Test of wire) |
1000.0 |
|
| 9.1 (Breaking Force of Strand) |
3000.0 |
|
| 9.1 (Elongation of Strand) |
1000.0 |
|
| 8.1 (Wire Diameter) |
1000.0 |
|
| 9.2 (Mass of Zinc Coating) |
2000.0 |
|
|
| 49 |
Custom specification (NWR)-Misc. - Custom specification (NWR)-Misc. |
Custom specification (NWR)-Misc. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Electrical Conductivity (EC)) |
500.0 |
|
| 2 (pH) |
500.0 |
|
| 4 (Total Dissolved Solids (TDS)) |
500.0 |
|
| 3 (Coliform) |
1000.0 |
|
|
| 50 |
IS 14268 (2022) - Uncoated stress relieved low relaxation seven - Wire (Ply) strand for prestressed concrete - Specification (First Revision) |
Uncoated stress relieved low relaxation seven - Wire (Ply) strand for prestressed concrete - Specification (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.1 (Nominal Mass of strand - IS 14268: 2022.) |
1500.0 |
|
| 6.1 (Nominal Diameter of strand- IS 14268: 2022.) |
1000.0 |
|
| 6.2 (Length of lay of Strand- IS 14268: 2022.) |
1000.0 |
|
| 4.2 (Centre wire shall have 1.5% greater in diameter than the surrounding wires - IS 14268: 2022.) |
1000.0 |
|
| Table 2 (Cl 6.2.1, Cl 6.2.2, Cl 6.3) (0.2% Proof Load, Breaking Strength of Strand, Total Elongation.) |
3000.0 |
|
| 6.2.3 (Total Elongation under Load on gauge length of 600 mm- IS 14268: 2022.) |
1000.0 |
|
| 6.2.2 (Breaking Load of Strand- IS 1608 (Part 1): 2022/ IS 14268: 2022.) |
3000.0 |
|
| 6.2.2 (0.2% Proof Load of Strand - IS 1608 (Part 1): 2022/ IS 14268: 2022.) |
1000.0 |
|
| 6.3 (Tensile Strength of Strand- IS 1608 (Part 1): 2022/ IS 14268: 2022, MPa.) |
1000.0 |
|
| 4.1.2 (Chemical composition (Annexure for NABL parameters)) |
3500.0 |
|
| 4.1.2 (Sulphur+Phosphorus (As per IS 7904:2018)) |
500.0 |
|
| 4.5 (Visual observation) |
1000.0 |
|
|
| 51 |
CUS/SR/MECH-2 - Shear plate |
Shear plate |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8 (Chemical composition) |
5000.0 |
|
| 1.0 (Breaking load) |
3000.0 |
|
|
| 52 |
Manufacture/Customer Specification - Test as per Manufacturer/Customer Specification |
Test as per Manufacturer/Customer Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 45 (Verification of Desktop Computer as per Manufacturer Technical Specification) |
5000.0 |
|
| 46 (Tests as per Manufacturer Technical Specification) |
10000.0 |
|
| 11 (Marking of Sample) |
1.0 |
|
|
| 53 |
IS 383 (2016) & CPWD Vol. I Specifications - Specification for Coarse & Fine Aggregate |
Specification for Coarse & Fine Aggregate |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| CPWD Specs (Silt Content) |
1000.0 |
|
| 6.3 (Sieve Analysis) |
2000.0 |
|
|
| 54 |
IS 398 : Part 4 (1994) - Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision) |
Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8 (Chemical composition) |
5000.0 |
|
| 12.4 (Resistance test of Aluminium Alloy wire(7 wire construction)) |
1000.0 |
|
| 9.2(2) (Measurement of lay ratio - Outer layer(19 wire construction)) |
1000.0 |
|
| 1 () |
- |
|
|
| 55 |
IS 398 Part 2 RA 2018 (2018) - ALUMINIUM CONDUCTORS FOR OVERHEAD TRANSMISSION PURPOSES |
ALUMINIUM CONDUCTORS FOR OVERHEAD TRANSMISSION PURPOSES |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 56 |
Custom-1-NTH-LM - Fence Post Hollow Section and Fence Post Support Strip |
Fence Post Hollow Section and Fence Post Support Strip |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8 (Chemical composition) |
5000.0 |
|
| 2 (Thickness) |
500.0 |
|
| 10 (Salt Spray Test for 1440 Hours) |
72000.0 |
|
| 7 (Mass of Zinc Coating) |
1000.0 |
|
| 9 (Powder coating thickness) |
1000.0 |
|
| 8 (Uniformity of coating) |
500.0 |
|
| 6 (Percentage Elongation at 5.65 √area) |
1000.0 |
|
| 5 (Yield Strength) |
1000.0 |
|
| 4 (Tensile Strength) |
1000.0 |
|
| 3 (Nominal Mass) |
1000.0 |
|
| 1 (Dimension of Post) |
1000.0 |
|
| 11 (Dimension of Fence Post Support Strip and anchor Rode) |
2000.0 |
|
| 9.1 (Powder coating thickness) |
1000.0 |
|
|
| 57 |
Custom-5-NTH-LM - Wire Mesh Panel |
Wire Mesh Panel |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Width) |
200.0 |
|
| 2 (Height) |
200.0 |
|
| 5 (Tensile Strength of wire) |
3000.0 |
|
| 10 (Diameter of Wire) |
500.0 |
|
| 7 (Mass of Zinc Coating) |
1000.0 |
|
| 10 (Diameter of Wire) |
500.0 |
|
| 8 (Powder Coating Thickness) |
2000.0 |
|
| 12 (Unit Weight) |
500.0 |
|
| 9 (Salt Spray Test for 1000 Hours) |
50000.0 |
|
| 19 (Uniformity of Coating) |
500.0 |
|
| 14 (Yield Stress of wire) |
1000.0 |
|
| 16 (Carbon) |
500.0 |
|
| 17 (Sulphur) |
500.0 |
|
| 18 (Phosphorus) |
500.0 |
|
| 18 (Sulphur + Phosphorus) |
500.0 |
|
| 8 (Chemical composition) |
5000.0 |
|
| 11 (Mesh Size (c/c)) |
300.0 |
|
| 9 (Salt Spray Test for 1440 hours) |
60000.0 |
|
| 0 (Powder Coating Thickness Test) |
2000.0 |
|
| 8 (Chemical composition) |
5000.0 |
|
| 6 (Weld Shear Strength) |
9000.0 |
|
| 2 (Adhesion test for coating) |
2000.0 |
|
| 4 (Panel Weight) |
500.0 |
|
|
| 58 |
IS 6012-1992 - Measurement of coating thickness by Eddy current method |
Measurement of coating thickness by Eddy current method |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Coating Thickness) |
2000.0 |
|
|
| 59 |
IS 17876 (2022) - Stainless Steel Welded Pipes and Tubes for General Services - Specification |
Stainless Steel Welded Pipes and Tubes for General Services - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 10.1 (Tensile Requirement - Tensile Strength as per IS 1608 Part 1 or Test Method specified) |
1000.0 |
|
| 10.1 (Tensile Requirement - Yield Strength as per IS 1608 Part 1 or Test Method specified) |
1000.0 |
|
| 10.1 (Tensile Requirement - %Percentage of Elongation (on Gauge Length of 50mm) as per IS 1608 Part 1 or Test Method specified) |
1000.0 |
|
| 24 (Outside Diameter, mm) |
1000.0 |
|
| 24 (Wall Thickness, mm) |
1000.0 |
|
| 8 (Chemical Composition - Ladle Analysis as per IS 228 and its relevant parts or any other established instrumental/chemical method) |
5000.0 |
|
|
| 60 |
IS 17875 (2022) - Stainless Steel Seamless Pipes and Tubes for General Services |
Stainless Steel Seamless Pipes and Tubes for General Services |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 10.1 (Tensile Strength) |
1000.0 |
|
| 10.1 (Yield Strength) |
1000.0 |
|
| 10.1 (Percent Elongation) |
1000.0 |
|
| 23 (Outside Diameter) |
500.0 |
|
| 23 (Wall Thickness) |
500.0 |
|
| 8 (CHEMICAL COMPOSITION,
C,Si,Mn,Ni,Cr, Mo, S,P,N,Cu ,Others) |
5000.0 |
|
| 12 (Rockwell Hardness) |
1500.0 |
|
| 12 (Brinell Hardness Test) |
1500.0 |
|
| 12 (Rockwell Hardness) |
1500.0 |
|
| 12 (Brinell Hardness Test) |
1500.0 |
|
|
