NTH - Management Information System

National Test House (NWR), Jaipur

E-763, Road No. 9 F1 V.K.I.A Jaipur-302013, Rajasthan, Jaipur, Jaipur, Rajasthan, 302013

9717298334 nthjaipur-ca@nic.in

Scope List

Reset

310 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

301

IS 3812 : Part 2 (2013) - Pulverized Fuel Ash - Part 2 : For Use as Admixture in Cement Mortar and Concrete

Pulverized Fuel Ash - Part 2 : For Use as Admixture in Cement Mortar and Concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Soundness by autoclave test — Expansion of specimen )	1500.0
7.1 (Fineness — Specific surface by Blaine’s permeability method)	1000.0
7.1 (Particles retained on 45 micron IS sieve (wet sieving) )	1000.0
5.1 ,6.1 (Available alkali as equivalent sodium oxide (Na2O))	500.0
5.1 ,6.1 (Loss on ignition)	500.0
5.1 ,6.1 (Magnesium oxide(MgO))	500.0
5.1 ,6.1 (Silicon dioxide(SiO2))	500.0
5.1 ,6.1 (Total Chlorides)	500.0
5.1 ,6.1 (Total Sulphur as sulphur trioxide(SO3))	500.0
5.1 ,6.1 (Reactive Silica)	500.0
5.1 ,6.1 (Silicon dioxide(SiO2) plus aluminium oxide (Al2O3) plus iron oxide (Fe2O3))	500.0
5.1 ,6.1 (Silicon dioxide(SiO2))	500.0

302

IS 3812 (Part 1) (2013) - Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

Pulverized fuel ash - Specification: Part 1 For use as pozzolana in cement, cement mortar and concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Compressive strength at 28 days )	3000.0
7.1 ( Lime reactivity — Average compressive strength )	3000.0
7.1 (Soundness by autoclave test — Expansion of specimen )	1500.0
7.1 (Fineness — Specific surface by Blaine’s permeability method)	1000.0
7.1 (Particles retained on 45 micron IS sieve (wet sieving) )	1000.0
5.1 ,6.1 (Available alkali as equivalent sodium oxide (Na2O))	500.0
5.1 ,6.1 (Loss on ignition)	500.0
5.1 ,6.1 (Magnesium oxide(MgO))	500.0
5.1 ,6.1 (Silicon dioxide(SiO2))	500.0
5.1 ,6.1 (Total Sulphur as sulphur trioxide(SO3))	500.0
5.1 ,6.1 (Reactive Silica)	500.0
5.1 ,6.1 (Total Chlorides)	500.0
5.1 ,6.1 (Silicon dioxide(SiO2) plus aluminium oxide (Al2O3) plus iron oxide (Fe2O3))	500.0

303

IS 13801 (2013) - Chequered Cement Concrete Tiles -

Chequered Cement Concrete Tiles -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.5 (Wet transverse strength)	2000.0
12.4 (Water Absorption)	1000.0
12.6 (Resistance to wear)	2000.0
12.3 (Straightness)	500.0
12.2 (Perpendicularity)	500.0
12.1 (Flatness)	500.0
10 (General Quality)	100.0
8.3 (Thickness of Wearing Layer)	500.0
7.1,Table 1,Column 2 (Dimensions -Length)	300.0
7 (Dimension: Thickness)	1000.0

304

IS 1786 (2008) - High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (2) (Carbon, % by mass (As per ASTM E 415-21/ IS 8811: 1998).)	500.0
4.2 (3) (Sulphur, % by mass (As per ASTM E 415-21/ IS 8811: 1998).)	500.0
4.2 (4) (Phosphorus, % by mass (As per ASTM E 415-21/ IS 8811: 1998).)	500.0
5.4 (Rib Area, mm²/ mm - IS 1786: 2008)	1000.0
9.2 (2) (Elongation Percent on gauge length of 5.65 Square Root of Crosss- Sectional Area, % - IS 1608 (Part 1): 2022.)	1000.0
9.2 (Yield Stress/ 0.2 % Proof Stress. N/mm² -- IS 1608 (Part 1): 2022.)	1000.0
9.2 (4) (Tensile Strength (up to 12 mm), N/mm² - IS 1608 (Part 1): 2022.)	-
9.2 (5) (Tensile Strength (16 to 28 mm), N/mm² - IS 1608 (Part 1): 2022.)	1000.0
9.2 (6) (Tensile Strength (32 to 40 mm), N/mm² - IS 1608 (Part 1): 2022.)	1500.0
9.3 (Bend test - IS 1599: 2023.)	1000.0
9.4 (Rebend test (0 - 28 mm) - IS 1786: 2008)	1000.0
7.2 (Mass per metre run, kg/m - IS 1786: 2008)	1000.0
4.2 (5) (Sulphur+ Phosphorus, % by mass.)	500.0
9.2 (1) (TS/ YS Ratio - (IS 1786: 2008/ IS 1608 (Part 1): 2022).)	-
9.4 (1) (Rebend test (32 to 40mm)- IS 1786: 2008)	1500.0
9.2 (3) (Total Elongation at Maximum Force on gauge length of 5.65 Square Root of Crosss- Sectional Area, % - IS 1608 (Part 1): 2022.)	-
0 (Salt spray test 48hrs as per ASTM B117)	2000.0
4.2 (19) (Chemical composition (HSDS with Corrosion Resistant Properties) in Annexure)	4000.0
5.7 (Pull out test upto 32mm)	15000.0

305

IS 8329 (2000) - Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13.3 (Wall Thickness of pipe)	1000.0
16.3 (Thickness of Cement mortar lining of pipe)	1000.0
15.3 (Ovality of pipe)	1000.0
10.2 (Brinell Hardness)	2000.0
10.1.1 (Tensile Strength)	2000.0
13.2 (Bore Clearance of mortar lining in ductile iron pipe)	1000.0
15.1.1 (External diameter)	1000.0
16.2 (C-2.3) (Bituminous Coating Test)	1000.0
10.1.1 (% Elongation)	-

306

IS 4985 (2021) - UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.7 (Sulphated ash Content)	2000.0
10.3 (Mercury for all three extracts)	1000.0
10.3 (Cadmiumfor all three extracts)	1000.0
10.3 (Di alky Tin C4 and higher homologous measured as Tin (Theird Extraction))	1000.0
10.3 (Lead theird extraction)	1000.0
10.3 (Lead first extraction)	1000.0
7.1.1.1 (Mean Outside Diameter)	1000.0
7.1.1.2 (Outside Diameter at any point)	1000.0
7.1.1.2 (Maximum Outside Diameter at any point)	1000.0
7.1.1.2 (Minimum Outside Diameter at any point)	1000.0
7.1.2 (Average Wall Thickness)	1000.0
7.1.2 (Maximum Wall Thickness)	1000.0
7.1.2 (Minimum Wall Thickness)	1000.0
7.2.1 (Visual Appearance of Socket)	1000.0
7.2.1.1 (Socket length)	1000.0
7.2.1.1 (Mean Socket internal diameter at mid point of socket length)	1000.0
7.2.1.1 (Maximum Socket internal diameter at mid point of socket length)	1000.0
7.2.1.1 (Minimum Socket internal diameter at mid point of socket length)	1000.0
7.2.1.1 (Included Angle of taper,( deg., minute))	1000.0
7.2.1.2 (Wall Thickness of socket (e2))	1000.0
7.2.1.2 (Wall Thickness of Seal Ring Groove (e3))	1000.0
7.2.1.2 (Depth of Engagement (min.))	1000.0
7.2.1.2 (Wall Thickness of socket (e2))	1000.0
9.2 (Pipe End (Chamfered), Wall thickness)	1000.0
11.1 (Acceptance Test for 1 hrs at 27 deg.C (4.19 x PN (MPA)) for Pipe)	5000.0
11.1 (Hydrostatic Pressure Test for 1000 hrs at 60 deg.C (Type Test))	20000.0
10.7 (Annex-B, IS:4985-2021)	2000.0
10.6 (IS:12235 (Part-14) Density)	2000.0
10.4 (IS:12235-(Part5/Sec.1 &2) Reversion test)	1000.0

307

IS 4984 (2016) - Polyethylene pipes for water supply - Specification (Fifth Revision)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.7 (Density at 27 degree celsius (base density))	1000.0
8.4 (Melt Flow Rate at 190 degree celcius and 5kgf)	2000.0
8.3 (Carbon Black Content)	2000.0
8.2 (Longitudinal Reversion Test)	2000.0
8.1 (Hydraulic Characteristics)	5000.0
7.4 (Wall Thickness)	500.0
7.1 (Visual Appearance)	500.0
6.2 (Colour)	-
8.6 (Overall Migration)	2000.0
8.3 (Carbon Black Dispersion)	1000.0
7.4.1.2 (Ovality)	100.0
6.2.1 (Colour Of strip)	-
6.2.1 (Width Of Strip)	100.0
6.2.1 (Depth Of strip)	100.0
7.4.1 (Outside Diameter)	500.0
8.1 (Internal Pressure Creep Rupture test of pipe for 48 hrs at 80deg.)	5000.0
8.1 (Internal Pressure Creep Rupture test of pipe for 165 hrs at 80deg.)	5000.0
8.6 (Overall Migration (Chemical Lab))	2000.0
8.5 (Oxidation Induction Time)	2000.0
8.9 (Elongation at Break Annex.-H, Table-6 (IS:4984-2016))	1000.0
8.9 (IS:4984, Annex.-H (Tensile Strength))	1000.0
firm's request (Density)	2000.0

308

IS 269 (2015) - Ordinary portland cement - Specification (Sixth Revision)

Ordinary portland cement - Specification (Sixth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7, Table 3, Sl No 4a (Compressive strength, MPa-(a) 72 ± 1 h IS 4031 (Part 6):1988)	1000.0
7, Table 3, Sl No 4b (Compressive strength, MPa (b) 168 ± 2 h IS 4031 (Part 6):1988)	1000.0
7, Table 3, Sl No 4c (Compressive strength, MPa (c) 672 ± 4 h IS 4031 (Part 6):1988)	1000.0
7, Table 3, Sl No 3b (Setting time: b) Final, IS 4031 (Part 5):1988)	250.0
7, Table 3, Sl No 3a (Setting time: a) Initial IS 4031 (Part 5):1988)	250.0
7, Table 3, Sl No 2b (Soundness b) By autoclave test method IS 4031 (Part 3):1988)	1000.0
7, Table 3, Sl No 2a (Soundness: a) By Le-Chatelier method, IS 4031 (Part 3):1988)	500.0
7, Table 3, Sl No 1 (Fineness IS 4031 (Part 2):1999)	1000.0
6.1, Table2, Sl No 6 (Loss on ignition IS 4032:1985)	600.0
6.1, Table2, Sl No 7 (Chloride content IS 4032:1985)	500.0
6.1, Table2, Sl No 4 (Magnesia IS 4032:1985)	600.0
6.1, Table2, Sl No 3 (Insoluble residue, IS 4032:1985)	600.0
6.1, Table2, Sl No 5 (Total Sulphur content percent by mass, IS 4032:1985)	500.0
6.1, Table2, Sl No 1 (Ratio of percentage of lime to percentages of silica, alumina and iron oxide, IS 4032 : 1985)	600.0
6.1, Table2, Sl No 2 (Ratio of percentage of alumina to that of iron oxide IS 4032:1985)	600.0
6.1, Table2, Sl No 8 (Alkali content IS 4032:1985)	1000.0
6.1 Table 2 Note 2.a (Tricalcium aluminate content, percent by mass)	-
6.1 Table 2 Note 2.b (Tricalcium Silicate content, percent by mass, Minimum)	-
Custom (Compressive strength, MPa-24h IS 4031 (Part 6):1988)	1000.0
13 (The standard consistency of cement paste(IS 4031(4):1988))	500.0

309

IS 11169 : Part 1 (1984) - SPECIFICATION FOR STEELS FOR COLD HEADING/COLD EXTRUSION APPLICATIONS (PART 1 WROUGHT CARBON AND LOW ALLOY STEELS)

SPECIFICATION FOR STEELS FOR COLD HEADING/COLD EXTRUSION APPLICATIONS (PART 1 WROUGHT CARBON AND LOW ALLOY STEELS)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.1.1 (Hardenability)	8000.0
10.3 (Inclusion rating)	4000.0
10.1 (Micro Structure)	3000.0
9.2 (Impact Strength)	3000.0
9.2 (Ultimate Tensile Strength)	1000.0
8.1 (Hardness)	1000.0
7.4 (Macro test)	1000.0
6.1 (Diameter of Wire)	500.0
4 (Chromium)	500.0
4 (Tin)	500.0
4 (Manganese)	500.0

310

RDSO C-9505 (2001) - Schedule of Technical Requirements for Enhanced Capacity (Alloy Steel) Screw Couplings used on Railway Coaches

Schedule of Technical Requirements for Enhanced Capacity (Alloy Steel) Screw Couplings used on Railway Coaches

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3.2 (Destruction Test)	7500.0
7.3.1 (Impact Test)	7500.0
7.3.1 (Impact Test)	7500.0
7.3.2 (Destruction Test)	7500.0