NTH - Management Information System

National Test House (NWR), Jaipur

E-763, Road No. 9 F1 V.K.I.A Jaipur-302013, Rajasthan, Jaipur, Jaipur, Rajasthan, 302013

9717298334 nthjaipur-ca@nic.in

Scope List

Reset

234 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

8623-1:(1993) - Low-Voltage Switchgear and Control gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type-Tested Assemblies [ETD 7: Low Voltage Switchgear and Control gear]

Low-Voltage Switchgear and Control gear Assemblies, Part 1: Requirements for Type-Tested and Partially Type-Tested Assemblies [ETD 7: Low Voltage Switchgear and Control gear]

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.2.1.3 (Tempreture rise test)	20000.0

IS 16353 (2015) - Portland Cement Clinker - Specification

Portland Cement Clinker - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	600.0
5 (Ratio of percentage of alumina to that of iron oxide)	600.0
5 (C3S)	600.0
5 (C3A)	600.0
5 (C3S + C2S)	600.0
5 (Total Sulphur content calculated as sulphuric anhydride(SO3))	500.0
5 (Free lime)	600.0
5 (Chloride content)	500.0
5 (Magnesia)	600.0
5 (Alkali content expressed as sodium oxide(Na2O))	1200.0
5 (Total loss on ignition)	600.0
5 (Insoluble residue)	600.0

IS 15965: 2012 - Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Mass of AZ Coating)	2000.0
8.3 of IS 15961 (Yield strength test, N/mm2)	3000.0
0 (Total coated thickness(TCT), mm)	1000.0
11 (Pitch of Corrugation, mm)	1000.0
11 (Depth of Corrugation, mm)	1000.0
7.3 (Top Coat)	1000.0
7.3 (Bottom Coat)	1000.0

FCO 1985 NANO FERTILISER - The Fertiliser (Inorganic, Organic or Mixed) (Control) Order 1985 (As amended up to October 2024)

The Fertiliser (Inorganic, Organic or Mixed) (Control) Order 1985 (As amended up to October 2024)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Schedule VII Clause 20 D(1) (As per Annexure (Attached)-NON NABL)	10000.0

IS 16651 (2017) - High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement - Specification

High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.3 (Mass per meter run.)	1000.0
9.2 (0.2 percent proof stress)	500.0
9.2 (Tensile Strength (dia of the bar 12-28 mm))	1500.0
9.3 (Bend Test)	1000.0
9.4 (Re Bend Test)	1000.0
9.2 (Percentage Elongation after Fracture.)	500.0
4.3.1 (4) (Carbon (as C))	500.0
4.3.1 (11) (Phosphorus (as P))	500.0
4.3.1 (7) (Sulphur (as S))	500.0
4.3.1 (5) (Silicon (as Si))	500.0
4.3.1 (6) (Manganese (as Mn))	500.0
4.3.1 (8) (Chromium (as Cr))	500.0
4.3.1 (9) (Nickel (as Ni))	500.0

CUSTOM-PI for IS 8042 (2015) - Performance Improver for white cement

Performance Improver for white cement

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (a) of IS 8042 (CaO + MgO, %)	3000.0
4.1 (b) of IS 8042 (Whiteness, %)	1000.0

IS 3589 (2001) - Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Carbon)	500.0
8.1 (Manganese)	1000.0
8.1 (Sulphur)	500.0
8.1 (Phosphorus)	500.0
9.2 (Flattening test)	1000.0
9.1 (Tensile Strength)	1000.0
9.1 (Elongation)	1000.0
9.1 (Yield Strength)	1000.0
11 (Weight)	1000.0
11 (Dimension (Diameter))	1000.0

Custom/Mech/2022 (2022) - Specification for Customer Test request.

Specification for Customer Test request.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
C3 (Tensile Strength (MPa))	1000.0
0 (Test results)	10000.0
8 (Dimensions)	2500.0
0 (Thickness, mm)	1000.0
8 (Dimensions)	2500.0
0 (Thickness, mm)	1000.0

Custom test IGNP Stage-II - Custom test IGNP Stage-II

Custom test IGNP Stage-II

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Customer Requirement)	10000.0

12818:2010 - PVC-U Screen and Casing Pipes for Bore/Tubewells

PVC-U Screen and Casing Pipes for Bore/Tubewells

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2.1 (IS:12818-2010 (OD))	500.0
7.2.1 (IS:12818-2010 (Wall Thickness))	500.0
9.3 (IS:12235 (Part-14) (Density))	2000.0
9.5 (IS:12235 (Part-13) Tensile Strength)	2000.0

Custom Plastic PT tests - Custom Plastic PT tests

Custom Plastic PT tests

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Custom Plastic PT tests (-)	-

IS 1367 : Part 3 (2017) - Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Wedge loading test)	3000.0
7 (Proof Load, N.)	3000.0
7 (Hardness Test)	2000.0
7 (Tensile load, N.)	3000.0
2 (Dimensions)	1500.0

IS 14490 (2018) - Plain copier paper - Specification (First Revision)

Plain copier paper - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.5 (IS:1060 (Part-5/sec.4) (Cobb))	2000.0
5.5 (IS/ISO 2471 (Opacity))	1000.0
5.5 (IS:1060 (Part-3)(Wax Pick No.))	1000.0
5.5 (IS:9894 (Smoothness (Bendsten)))	2000.0
5.5 (IS:9894 (Smoothness (Bendsten) other side))	2000.0
5.5 (IS:1060 (Part-6/sec.1))	1000.0
5.5 (IS:1060 (Part-6/Sec.1) (Tear Index))	1000.0
5.5 (IS:1060 (Part-5/sec.6) (Tensile Index (MD)))	1000.0
5.5 (IS:1060 (Part-5/sec.6) (Tensile Index (CD)))	1000.0
5.5 (Ash Content)	2000.0
5.2 (Moisture)	2000.0
5.5 (Brightness)	2000.0
5.4 (Thickness)	1000.0
5.3 (Grammage)	1000.0
5.1 (General)	1000.0
5.6 (IS:14490)	500.0
5.2 (Moisture)	2000.0

Custom for Ace Flexi pack - Custom for Ace Flexi pack specification for Degradable bags

Custom for Ace Flexi pack specification for Degradable bags

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (IS: 2508 Thickness (micron))	1000.0
2 (IS:9738:2003 (Water Leak Test ))	1000.0
3 (IS:12395 (Resistance to Drop Impact test))	1000.0

IS 9806 (2001) - Methods of test for and permissible limits of toxic materials released from ceramicware, vitreous enamelware, glassware and glass - Ceramicware in contact with food (First Revision)

Methods of test for and permissible limits of toxic materials released from ceramicware, vitreous enamelware, glassware and glass - Ceramicware in contact with food (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10 (Lead (Pb) mg/l)	1000.0
10 (Cadmium (as Cd) mg/l)	1000.0

IS 6745 (1972) - Mass of Zinc Coating (IS 6745)

Mass of Zinc Coating (IS 6745)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Mass of Zinc Coating,(IS 6745:1972))	2000.0

IS 3204 (1978) - Specification for limestone for chemical industry (First Revision)

Specification for limestone for chemical industry (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 & 5.2.6 (Magnesium (as MgO))	1000.0
3.2 & 5.2.5 (Calcium (as CaO))	1000.0
3.2 & 5.2.4 (Iron (as Fe2O3))	1000.0
3.2 & 5.2.2 (Loss on ignition)	1000.0
3.2 & 5.2.3 (Silica (as SiO2))	1000.0
3.2 & 5.2.10 (Silica (as SiO2), Alumina(Al2O3) and ferric oxide as (Fe2O3) together)	3000.0

IEC 60099 - 4 (2014) - Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems

Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.13 (Seal Leak Test)	10000.0

IS 1161 (2014) - Steel Tube for Structural Purposes

Steel Tube for Structural Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Weight)	1000.0
6.1 (Thickness)	500.0
6.1 (Outside Diameter)	500.0
11.2 (Tensile Strength, MPa)	1000.0
11.2 (Yield strength, MPa)	1000.0
11.2 (Percent Elongation, %)	1000.0
11.3 (Cold Bend test)	-
11.3 (Bend Test / Flattening test)	1000.0
8 (Mass of Zinc Coating)	2000.0
0 (Uniformity of Coating)	1000.0

IS 2629 (1985 (Reaffirmed 2021)) - Recommended Practice for Hot-Dip Galvanizing of Iron and Steel – Specification

Recommended Practice for Hot-Dip Galvanizing of Iron and Steel – Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.3 (Mass of Coating)	2000.0

IS 2250:1981 - Code of Practice for Preparation and use of Masonry Mortars

Code of Practice for Preparation and use of Masonry Mortars

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6,Table 1 (Grade of Mortar-Mortar mix ratio (IS 1199))	5000.0
Custom ( ref 5.1.4) (Sulphate content)	1200.0
Custom (Chloride content)	1200.0

IS 17425 (2020) - Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1.2 (IS:17425 & Annex-A(Acceptance test))	5000.0
7.1.1 (IS:17425 (Visual Appearance))	500.0
6.2.1 (IS:2530 (C.B.C))	2000.0
4.1.4 (IS:2530 (CBD))	1000.0
7.1.3 (IS:17425 (Reversion))	1000.0
5.1.2 (IS:17425 (Ovality))	500.0
7.1.4 (IS:17425 & Annex-D (Tensile Strength))	2000.0
7.1.4 (IS:17425 & Annex-D (Elongation at Break))	2000.0
7.1.7 (IS:2530 (MFR))	2000.0
7.1.6 (IS:7328 (Density))	2000.0
7.1.2 (IS:17425 & Annex-A) (Quality test))	5000.0
5.1.1 (IS:17425 (OD))	500.0
5.1.1 (IS:17425 (Wall thickness))	500.0
7.2.1 (IS:17425 (Leakage Test))	5000.0

IS 1161 (2014) - Steel tubes for structural purposes - Specification (Fifth Revision)

Steel tubes for structural purposes - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.3.1 (Cold Bend Test up to 50 mm NB)	1000.0
11.3.2 (Flattening Test above 50 mm NB)	1000.0
11.2 (Percentage Elongation, %)	1000.0
11.2 (Yield Strength, MPa)	1000.0
11.2 (Tensile Strength, MPa)	1000.0
6 (Dimension)	1000.0
6 (Mass per meter, kg/m)	1000.0
8 (Coating thickness, micron)	2000.0
5 (Chemical Composition)	2500.0

IS 2046 NR CIVIL (1995 Reaffirmed 2005) - Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.5 & 5.3 (Dimensions-Length, Width, Thickness, Wraping (Flatness), Reverse Side Bonding)	4000.0
5.5 (Resistance to Immersion in Boiling Water (Mass increase, Thickness increase, Appearance))	3500.0
5.5 (Resistance to Steam)	2000.0
5.5 (Resistance to Cracking)	2000.0

IS 4270 (2001) - Steel tubes used for water wells specification (Third Revision)

Steel tubes used for water wells specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Outside diameter)	3000.0
6.2 (Flattening)	1000.0
6.1 (Tensile Strength)	1000.0
7 (Weight in kg/m)	1000.0
7 (Thickness)	250.0
6.1 (Yield Strength)	1000.0
6.1 (% Elongation)	1000.0
5.2 (Sulphur)	1250.0
5.2 (Phosphorus)	1250.0

IS 16172 (2023) - Reinforcement couplers for mechanical splices of bars in concrete - Specification

Reinforcement couplers for mechanical splices of bars in concrete - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2 (Tensile Strength as per IS 1608(Part 1):2022)	1500.0
9.2 (Percentage Elongation as per IS 1608(Part 1):2022)	1500.0

IS 17545:2021 - WHITE CEMENT BASED POLYMERIC PUTTY

WHITE CEMENT BASED POLYMERIC PUTTY

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Form and Condition)	500.0
4.3 (Consistency)	500.0
4.5 Table, 1, (i) (Average Tensile adhesion strength@ 14days-Annex B)	2000.0
4.5, Table 1, (ii) (Water retentivity-Annex C)	1000.0
4.5, Table 1, (iii) (Initial Setting time-Annex D)	250.0
4.5, Table 1, (v) (Degree of whiteness-Annex B of IS 8042)	2000.0
4.6 Table 2 (28 days Compressive strength-IS 4031(6))	1000.0
4.6 Table 2 (28 days Compressive strength-IS 4031(6))	1000.0
4.6, Table 2, (i) (28 days Compressive strength-IS 4031(6))	1000.0
4.5, Table 1, (iii) (Final Setting time-Annex D)	250.0
4.5, Table 1, (iv) (Polymer content(based on loss on ignition)-Annex E)	1000.0
4.5, Table 1, (vi) (Cement content-Annex B of IS 5410)	1000.0
4.4 (Lead Restriction-ASTM D3335-85a.)	1000.0

IRS-GE-1 (2016) - Specifications for Track ballast (IRS-GE-1)

Specifications for Track ballast (IRS-GE-1)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.2.1 (Aggregate abrasion Value (IS 2386(IV):1963))	2500.0
2.2.2 (Aggregate Impact Value (IS 2386(Part IV):1963))	2500.0
2.2.3 (Water absorption ( IS 2386 (III):1963))	1000.0

IS 2508 (2016) - Low Density Polyethylene Films

Low Density Polyethylene Films

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Nominal thickness)	1000.0

IS 7098 : Part 2 (2011) - Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
19.2.(a) (Annealing test ( for copper ))	1000.0
19.2.(b) (Tensile Test (for aluminium))	500.0
19.2.(c) (Wrapping test)	1000.0
19.2.(d) (Resistance of conductor-R)	1000.0
19.2.(d) (Resistance of conductor-Y)	1000.0
19.2.(d) (Resistance of conductor-B)	1000.0
19.2.(d) (Resistance of conductor-Black)	250.0
19.2.(e) (Average thickness of sheath)	250.0
19.2.(e) (Average thickness of insulation)	250.0
19.2.(e) (Minimum thickness of sheath)	250.0
19.2.(e) (Minimum thickness of insulation)	1000.0
19.2.(f) (Hot set test-Permanent elongation under load)	1000.0
19.2.(f) (Hot set test-Permanent elongation after cooling)	1000.0
19.2.(g) (Elongation at break)	5000.0
19.2.(k) (Volume resistivity at ambient temperature (27 degree C +/- 2 degree C )-R)	1000.0
19.2.(k) (Volume resistivity at ambient temperature (27 degree C +/- 2 degree C )-Y)	1000.0
19.2.(k) (Volume resistivity at ambient temperature (27 degree C +/- 2 degree C )-B)	1000.0
19.2.(k) (Volume resistivity at ambient temperature (27 degree C +/- 2 degree C )-Black)	1000.0
19.2.(k) (Volume resistivity at 90 Degree C-R)	1000.0
19.2.(k) (Volume resistivity at 90 Degree C-Y)	1000.0
19.2.(k) (Volume resistivity at 90 Degree C-B)	1000.0
19.2.(k) (Volume resistivity at 90 Degree C-Black)	100.0
19.1.(iii)b) (Ageing in air oven,Elongation at break)	1000.0
19.1.(iii) e) (Shrinkage)	500.0
19.1.(iii) f) (Water absorption (Gravimetric))	1500.0
19.1.(vi)(d) (Hot deformation test )	1000.0
19.1.(vi)(g) (Thermal stability)	5000.0

First
Prev
2
3
4
5
Next
Last