NTH - Management Information System

Search by Standard No.

Reset

4064 Results

S.No.

Lab Name

Standard No.

Product

Testing Charges (Excl. Of Taxes)

3121

National Test House (ER), Kolkata

JIS D 5301:2006 - Lead Acid starter Batteries

Lead Acid starter Batteries

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.5.2 (5 h rate capacity)	20000.0
Annexure 1 Clause 2 (Water consumption test)	10000.0
10.1 (20 h rate capacity (C20) test)	25000.0
10.2 (Reserve capacity test)	20000.0
10.3 (Cold cranking ampere test)	15000.0
10.4 (Charge acceptance test)	10000.0
10.5(a) (Light load endurance test)	25000.0
10.5(b) (Heavy load endurance test)	25000.0
10.6 (Vibration resistance)	10000.0
10.7 (Terminal strength test)	5000.0
10.8 (Fastening robustness test)	5000.0
10.9 (Electrolyte retention test)	20000.0
10.10 (Charge retention test)	15000.0
Annex A, Table A.2 (Dimension)	5000.0

3122

National Test House (Satellite Centre), Varanasi

IS 14887 (2014) - Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1.1 (Mass of Sack)	1000.0
4.1.1 (Ash Content)	2000.0
4.1.1 (Picks/dm)	1000.0
4.1.1 (Ends/dm)	1000.0
4.1.1 (Dimensions, Inside Width)	1000.0
4.1.1 (Dimensions, Inside Length)	1000.0

3123

National Test House (NR), Ghaziabad

1239 (2011) - Steel Tubes, Tubulars and other Steel Fittings, PART 2 STEEL PIPE FITTINGS

Steel Tubes, Tubulars and other Steel Fittings, PART 2 STEEL PIPE FITTINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Dimension,mm.)	1000.0
13.1.1 (Mass of Zinc Coating)	2000.0
13.1.2 (Uniformity of Zinc Coating)	500.0
14 (Workmanship, Visual)	500.0
3.1 (Sulphur (% by mass))	700.0
3.1 (Phosphorous (% by mass))	700.0

3124

National Test House (ER), Kolkata

GE: IRS -2 (Final) (2005) - SPECIFICATION FOR MECHANICALLY PRODUCED BLANKETING MATERIAL FOR RAILWAY FORMATIONS INCLUDING GUIDELINES FOR LAYING

SPECIFICATION FOR MECHANICALLY PRODUCED BLANKETING MATERIAL FOR RAILWAY FORMATIONS INCLUDING GUIDELINES FOR LAYING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1.C.1 (Test for Non Plastic fines(Particles of size less than 75 micron)(as per GE: IRS -2 (Final)))	1000.0
4.1.C.2 (Test for Plastic fines(GE: IRS -2 (Final)))	1000.0
4.1.d (Test for Particle size distribution(GE: IRS -2 (Final)))	5000.0
4.1.e.1 (Test for Uniformity Co-efficient (Cu) {GE: IRS -2 (Final)})	1500.0
4.1.e.2 (Test for Co-efficient of Curvature(CC) (GE: IRS -2 (Final)))	1500.0
Nil (Liquid Limit (IS 2720(5)-1985))	1000.0
- (Plastic limit (IS 2720(5):1985))	1000.0
- (Free soil Index(IS 2720(40)1977))	1000.0
- (Shrinkage limit (IS 2720(6)1985))	1000.0
- (DETERMINATION OF WATER CONTENT-DRY DENSITY RELATION (IS 2720(8):1983) (Proctor test))	5000.0
- (Test for Aggregate Abrasion Value (Los Angeles) as per IS 2386 (Part 4): 1963)	1500.0

3125

National Test House (ER), Kolkata

customer specification ER CHEMICAL METAL LAB (2022) - customer specification ER CHEMICAL METAL LAB

customer specification ER CHEMICAL METAL LAB

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Zinc (as Zn),% by mass)	2000.0
2 (Aluminum as Al % by mass)	2000.0

3126

National Test House (NER), Guwahati

NTH/NER/Custom/2022/03 - Chemical General

Chemical General

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Silica (as SiO2), % by mass)	1000.0
2 (Alumina (as Al2O3), % by mass)	1000.0
3 (Iron Oxide (as Fe2O3), % by mass)	1000.0
4 (Calcium Oxide (as CaO), % by mass)	1000.0
5 (Magnesium Oxide (MgO), % by mass)	1000.0
6 (Mixed Oxide (as R2O3), % by mass)	2000.0
7 (Iron (as Fe), % by mass)	1000.0
8 (Loss on ignition, % by mass)	1000.0
9. (Sulphuric anhydride (as SO3), % by mass - IS 4032:1985)	1000.0
10. (Chloride (as Cl), % by mass - IS 4032:1985)	1000.0
11. (Alkali content (as Na2O), % by mass - IS 4032:1985)	2000.0
12 (Available lime (as CaO), percent by mass)	1000.0
13 (Acid insoluble matter ( as SiO2 ), percent by mass)	1000.0
14 (Particle size (Pass through 2 mm IS sieve))	1000.0
16 (Sulphur, percent)	1000.0
15 (Moisture, percent)	1000.0
16 (Gross calorific value, KCal/Kg)	2000.0
18 (Silica (as SiO2))	1000.0
19 (Ash content)	2000.0
20 (Moisture content)	1200.0
21 (Zinc (as Zn))	2000.0
22 (Chromium (as Cr))	1200.0
23 (Selenium (as Se))	1200.0
24 (Cobalt (as Co))	1200.0
25 (Lead (as Pb))	1200.0
26 (Cadmium (as Cd))	1200.0
27 (Manganese (as Mn))	1200.0
28 (Nickel (as Ni))	1200.0
29 (Iron (as Fe))	1200.0
30 (Alkali content (as Na2O), % by mass)	750.0
31 (Alkali content (as K2O), % by mass)	750.0
32 (Silt content, % by mass)	1000.0

3127

National Test House (ER), Kolkata

RDSO/PE/SPEC/AC/0059-2004(Rev.O),Amendment No-01 (2004) - V-Belts used For Driving Alternators For TL and AC Coaches

V-Belts used For Driving Alternators For TL and AC Coaches

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.0 (Pitch length)	5000.0
7.0 (Coding)	1000.0
3.1 (Construction)	2000.0
3.2(i) (Hardness(IRHD))	1000.0
3.2(ii) (Tensile Strength of base material)	2000.0
3.2(iii) (Elongation at break of base material)	1000.0
3.3(i) (Elongation of Finished Belt)	1000.0
3.3(ii) (Reference Elongation at 300 kgf of Finished Belt)	1000.0
3.3(iii) (Breaking Strength)	2000.0
5.1(i) (Nominal Top width)	1000.0
5.1(ii) (Nominal Thickness)	1000.0
5.1(iii) (Angle)	1000.0
12.7(i) (Change in Hardness after ageing)	1000.0
12.7(ii) (Change in Tensile Strength after ageing)	2000.0
12.7(iii) (Change in elongation after ageing)	1000.0
12.7(iv) (Compression set)	1000.0

3128

National Test House (NR), Ghaziabad

IRS : TC 30-05 - UNDERGROUND RAILWAY JELLY FILLED QUAD CABLES FOR SIGNALLING AND TELECOM INSTALLATIONS

UNDERGROUND RAILWAY JELLY FILLED QUAD CABLES FOR SIGNALLING AND TELECOM INSTALLATIONS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1.1 (Diameter mm (Nominal) - 0.90 Tolerance mm - +-0.02 Maximum Resistance Ohm/ Km at 20 deg C Each core - 28 Loop - 56)	1000.0
3.1.2 (The conductor shall be uniformly drawn, circular in Closs-section, uniform III qiI<lhty, free from splits, cracks, corrosion and other surface imperfectIons)	100.0
3.1.3 (No joints shall be made in the conductor except in exceptional cases where It IS necessary to join conductors during manufacture, it shall fulfill. the requirements of clause 3.1.)	1.0
5.5.1 (The diameter of the conductor shall be measured on the finished sample. The measurement shall be made atleast at three different points with two readings at 90 degree along the length of the sample.)	1.0
5.5.2 (A sample of wire taken from finished cable, when tested shall have elongation at fracture of not less than 23 d for diameter O.9 mm)	1.0
5.7.1 (Determination of the thickness of insulation of round cores and sheath shall be made on a representative sample of the cable approximately one meter long taken from the drum length of the cable.)	1.0
5.7.2 (The measurement in case of conductor insulation, inner, intermediate and outer sheath shall be made at three different points at interval of not less than 75 mm along the length of the sample and at each point the minimum thickness or the'insulation inner, intermediate & outer sheath shall be measured along with two more readings made at equidistant points around the periphery.)	1.0
3.8.3 (The number and the size of the aluminium wires/strips used for screening shall be such as to comply with the requirements of Cl 5.9.9)	200.0
3.8.4 (The layer of the aluminium wires/ strips used for screening shall be compact and the length of the lay shall be high.)	200.0
3.8.5 (The minimum tensile strength of Aluminium screen shall be 15 Kg/ Sqmm)	200.0
3.8.6 (The innermost layer of the screening shall have left hand lay and the sucessive layer shall be laid with opposite lay.)	200.0
3.8.7 (Drift expansion test to IS 2335-1985 shall be carried out on a test piece of length twice the external dia of the tube by conical mandrel having height three times its base diameter.)	200.0
3.8.8 (Flattening test to IS. 2328- 1983 shall be carried out on a test piece of not less than 50 mm long cut from each selected tube.)	200.0
3.9.1 (The aluminium screen shall be wrapped with a single layer of woven tape impregnated with Barium Chromate with minimum 20% overlap.)	500.0
3.9.2 (The tape used shall be fine woven cloth tape of about 0.15 mm thickness.)	200.0
3.10.7 (The test shall be conducted on PVC intermediate sheath in accprdance with BS 6169 or any approved method.)	1000.0
5.8.1.1 (The test shall be conducted in accordance with the procedure laid down in IS 10810 (Part-7))	500.0
5.8.1.2 (The values after ageing for tensile strength and % elongation shall not be less than given in Cl 5.8.1)	500.0
5.8.1.3 (The values of all the four samples in case of each sheath shall be averaged and then % variation calculated.)	1.0
5.8.2.4 (A sample shall be cut from the cable sheath, 50 mm long measured along the axis. 12 mm wide and the same thickness as the cable sheath)	1000.0
5.8.11 (The test to be conducted in accordance with the procedure laid down in IS 10810 (Part 60))	500.0
3.3 (i) Four conductors insulated as above shall be stranded to form a star, quad. each; conductors diagnolly opposite forming one pair and the remaining two diagonally OPPOS); conductors furming the second pairs of the quad. ii) The lays of the conductors forming the quads shall differ for adjacent quads. The lay of the conductor shall be so chosen as to ensure that the cross talk between the pairs in the cable minimum.)	1000.0
3.4 (Each quad shall retain its size)	1.0
3.12 (Visual Inspection and Marking)	100.0
5.8.22 (Visual Inspection and Marking)	100.0
5.9.1 (HV Test to be carried out)	2000.0
5.9.2 (Insulation resistance Test)	1000.0
5.9.3 (Conductor Resistance Test)	1.0
5.6.3.1 (Mass of Zinc Coating test)	3000.0
5.8.2.3 (Shrinkage Test of PE Insulation)	1000.0
5.8.2.2 (Shrinkage Test of PVC Sheaths)	1000.0

3129

National Test House (SR), Chennai

IEC 62561-2 (2018) - Lightning Protection System components (LPSC) - Part 2: Requirements for conductors and earth electrodes

Lightning Protection System components (LPSC) - Part 2: Requirements for conductors and earth electrodes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2.6 (Tensile strength)	4000.0

3130

National Test House (SR), Chennai

IEC 62561-1 (2017) - Lightning Protection System components (LPSC) - Part 1: Requirements for connection components

Lightning Protection System components (LPSC) - Part 1: Requirements for connection components

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.5 (Static mechanical test)	5000.0

3131

National Test House (ER), Kolkata

IS 542 (2018) - Coconut oil - Specification (Third Revision)

Coconut oil - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2.1 (Clarity)	500.0
5.7 (i) (moisture and insoluble impurities)	500.0
5.7(ii) (colour in lovibond scale)	500.0
5.7(iii) (Refractive index 40 dg)	500.0
5.7(iv) (Specific gravity 30 dg)	500.0
5.7 (v) (saponification value)	500.0
5.7(vi) (Iodine value)	500.0
5.7 (vii) (Acid value)	500.0
5.7(viii) (Unsaponifiable matter)	500.0
5.7 (ix) (Polenske value)	500.0
5.3 (Test for presence of Karanja oil)	500.0
5.3 (Test for presence of Kusum oil and other oils containing cyanogenic compounds)	500.0
5.3 (Test for presence of Castor oil)	500.0
5.3 (Test for presence of Hydrocyanic acid)	500.0
5.3 (Test for presence of Argemone oil)	500.0
5.3 (Test for presence of mineral oil)	500.0
5.3 (Test for presence of neem oil)	500.0

3132

National Test House (NR), Ghaziabad

IS 191 (2007) - Copper - Specification (Fourth Revision)

Copper - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Selenium+Tellurium)	2000.0
7.1 (Zinc )	1000.0
7.1 (Tin )	1000.0
7.1 (Tellurium)	1000.0
7.1 (Selenium)	1000.0
7.1 (Oxygen)	5000.0
7.1 (Lead )	1000.0
7.1 (Bismuth)	1000.0
7.1 (Antimony)	1000.0
7.1 (Arsenic )	2000.0
7.1 (Nickel )	1000.0
7.1 (Sulphur)	1000.0
7.1 (Iron )	1000.0
7.1 (Phosphorus )	1000.0
7.1 (Silver )	1000.0
7.1 (Copper + Silver )	2000.0

3133

National Test House (NR), Ghaziabad

IS 110 (2017) - Ready mixed paint, brushing, grey filler, for enamels for use over primers - Specification (Third Revision)

Ready mixed paint, brushing, grey filler, for enamels for use over primers - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3xiii (Keeping properties)	5000.0

3134

National Test House (NR), Ghaziabad

IS 158 (2015) - Ready mixed paint, brushing, bituminous, black, acid, alkali and heat resisting - Specification (Fourth Revision)

Ready mixed paint, brushing, bituminous, black, acid, alkali and heat resisting - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3,xvi (Keeping properties)	500.0
4.3,xv (Flash Point)	500.0
4.3,xiv (Resistance to heat)	200.0
4.3,xiii (Resistance to alkali)	1000.0
4.3,xii (Resistance to acid)	2000.0
4.3,xi (Volatile matter, percent by mass)	200.0
4.3,x (Protection against corrosion under conditions of condensation)	2000.0
4.3, ix (Stripping Test)	1000.0
4.3, viii (Flexibility and adhesion, bend test with 6.25 mm dia mandrel and type 1 apparatus)	1000.0
4.3,vii (Water Content,percent by mass)	100.0
4.3,vi (Mass, kg/10litre)	100.0
4.3,v (Colour)	100.0
4.3,iv (Wet opacity)	500.0
4.3,iii (Finish)	100.0
4.3,ii (Consistency)	1000.0
4.3,i (Drying time : Hard dry)	1000.0
4.2 (Lead Restrictions)	1500.0

3135

National Test House (NR), Ghaziabad

IS 383 for fine aggregate (2016) - Coarse and fine aggregate for Concrete

Coarse and fine aggregate for Concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Test for Alkali aggregate reaction- Chemical method (IS 2386(Part 7):1963))	3000.0
Clause 5.7 Table 3 (TOTAL ALKALI CONTENT as Na2O EQUIVALENT)	1000.0
5.7 TABLE 3 (TOTAL SULPHATE CONTENT as SO3)	1000.0
5.7 TABLE 3 (ACID SOLUBLE CHLORIDE CONTENT)	1000.0
6 (Test for Silt content- (CPWD Specification))	1000.0
6.3 (Sieve analysis/Particle size distribution)	2000.0
2 (Test for Specific Gravity (IS:2386(part -III)1963))	500.0
4 (Test for Bulk Density-Loose condition ( IS:2386(part -III)1963))	500.0
5 (Test for Bulk Density-Compacted condition ( IS:2386(part -III)1963))	500.0
3 (Test for Water absorption (IS:2386(part -III)1963))	1000.0
7 (Deleterious Materials)	2000.0
10 (Test for bulking of sand)	1000.0
8 (Test for Soundness of Aggregate (IS 2386(Part 5):1963))	2000.0
7 (Deleterious Materials)	2000.0

3136

National Test House (NR), Ghaziabad

IS 1171 (2011) - Ferromanganese - Specification (Fifth Revision)

Ferromanganese - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1.3 Ferromanganese High Carbon (Manganese Content %)	2000.0
3.1.3 Ferromanganese High Carbon (Carbon %)	1500.0
3.1.3 High carbon ferromanganese (Silicon %)	1500.0
3.1.3 Ferromanganese High Carbon (Sulphur %)	1500.0
3.1.3 Ferromanganese High Carbon (Phosphorus (as P)%)	1500.0

3137

National Test House (NR), Ghaziabad

IS 1079 (2017) - Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Chemical Analysis)	2500.0
8.3 (0.2 Proof Stress / Yield Stress (Drawing quality))	1000.0
8.3 (Tensile Strength for Designation Ordinary, Commercial and General purpose.)	2000.0
8.3 (Elongation)	1000.0
9 (Bend Test)	1000.0
13 (Dimensions)	1000.0
1 (Mass of Zinc Coating)	2000.0

3138

National Test House (NR), Ghaziabad

IS 2339 (2013) - Aluminium paints for general purposes - Specification (First Revision)

Aluminium paints for general purposes - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.3 ix (Keeping properties)	5000.0
5.3viii (Flash point)	2000.0
5.3 vii (Resistance to humidity under condition of condensation)	3000.0
5.3 vi (Flexibility and adhesion, bend test usingType 1 apparatus and 6.25 mm dia Mandrel)	200.0
5.3 v (Wet Opacity)	500.0
5.3 iv (Mass)	200.0
5.3 iii (Finish)	200.0
5.3 ii (Consistency)	200.0
5.3 i (Drying Time Hard dry)	200.0
5.2 (Lead Resistrction)	500.0
5.1.1 (Leafing Value)	1500.0
5.1 (Compostion)	200.0

3139

National Test House (NR), Ghaziabad

IS 299 (2012) - Alumino - Ferric - Specification (Fifth Revision)

Alumino - Ferric - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Selenium (as Se))	1000.0
4.2 (Cadmium (as Cd))	500.0
4.2 (Chromium (as Cr))	500.0
4.2 (Manganese (as Mn))	500.0
4.2 (Mercury (as Hg))	1000.0
4.2 (Arsenic (as As2O3))	1000.0
4.2 (Lead (as Pb))	500.0
4.2 (Free acidity (As H2SO4), Basicity ( as Al2O3),)	1000.0
4.2 (pH (of 5 percent aqueous solution),)	1000.0
4.2 (Water soluble aluminium compounds (as Al2O3))	1000.0
4.2 (Soluble iron compound (as Fe))	1000.0
4.2 (Insouble matter)	1000.0
4.2 (Anionic detergents (as MBAS), parts per million)	1000.0
4.2 (Phenolic compounds (as C6H5OH), parts per million)	1000.0

3140

National Test House (NR), Ghaziabad

IS 15489 (2013) - Paint, plastic emulsion - Specification (First Revision)

Paint, plastic emulsion - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.12 (Toxic metals such as lead, cadmium, chromium (VI))	3600.0
6.12 (Volatile organic compounds,)	2000.0
6.1 (Keeping properties)	5000.0
6.5 (Mass in kg/10 litre (IS 101 (Part 1/Sec 7)))	500.0
6.11 (Recoating properties, (Annexure J of IS 15489:2013))	2000.0
6.11 (Resistance to alkali (Annexure F of IS 15489:2013))	500.0
6.11 (Accelerated storage stability test (Annexure H of IS 15489:2013))	700.0
6.11 (Colour (Annexure E of IS 15489:2013))	100.0
6.11 (Gloss at 60 degree d) Class D, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree c) Class C, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree b) Class B, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree a) Class A (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Finish (Annexure D of IS 15489:2013))	1200.0
6.11 (Consistency (Annexure B of IS 15489:2013))	1200.0
6.11 (Drying time a) Hard dry (Class C and D) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Hard dry (Class A and B) (Annexure D of IS 15489:2013))	1200.0
6.11 (Drying time a) Surface dry (Class C and D) (Annexure D of IS 15489:2013))	1200.0
6.11 (Drying time a) Surface dry (Class A and B) (Annexure D of IS 15489:2013))	1200.0
6.9 (Lead Restriction)	1000.0
6.2 (Conditions in the Container)	200.0
6.3 (Thinning)	1200.0
6.4 (Application)	1200.0

3141

National Test House (NR), Ghaziabad

IS 101 part 6 sec 1 (1988) - "METHODS OF SAMPLING AND TEST FOR PAINTS, VARNISHES AND RELATED PRODUCTS" SALT SPRAY FOR 96 HRS.

"METHODS OF SAMPLING AND TEST FOR PAINTS, VARNISHES AND RELATED PRODUCTS" SALT SPRAY FOR 96 HRS.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Neutral Salt Spray (96 hrs.))	8000.0

3142

National Test House (NR), Ghaziabad

IS 73 (2013) - Paving bitumen - Specification (Fourth Revision)

Paving bitumen - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2(vii)a (Viscocity ratio 60dg)	1200.0
6.2(vi) (Softening Point (R&B))	1200.0
6.2(iv) (Flash Point, cleveland Open cup)	1200.0
6.2(v) (Solubility in TCE)	1200.0
6.2(iii) (Kinematic viscocity,135 dg)	1200.0
6.2 (i) (Penetration,25 dg 100g 5sec 0.1 mm)	1200.0
6.2(vii)b (Ductility dg)	1200.0

3143

National Test House (NR), Ghaziabad

IS 101 : Part 8 : Sec 5 2022 (2022) - Methods of sampling and test for paints, varnishes and related products: Part 8 tests on liquid paints (General And Physical): Sec 5 Lead Restriction Test

Methods of sampling and test for paints, varnishes and related products: Part 8 tests on liquid paints (General And Physical): Sec 5 Lead Restriction Test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
101 part 8 sec 5 (Lead Restriction Test)	2500.0

3144

National Test House (NR), Ghaziabad

IS 1367 : Part 6 (2018) - Technical Supply Conditions for Threaded Steel Fasteners Part 6 Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel — Nuts with Specified Property Classes — Coarse Thread and Fine Pitch Thread

Technical Supply Conditions for Threaded Steel Fasteners Part 6 Mechanical Properties of Fasteners Made of Carbon Steel and Alloy Steel — Nuts with Specified Property Classes — Coarse Thread and Fine Pitch Thread

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Lead, % by mass)	500.0
6 (Chemical composition, % by mass)	2500.0

3145

National Test House (NR), Ghaziabad

IS 1367 : Part 3 (2017) - Technical Supply Conditions for Threaded Steel Fasteners Part 3 Mechanical Properties of Fasteners Made of Carbon Steel and Bolts, Screws and Studs

Technical Supply Conditions for Threaded Steel Fasteners Part 3 Mechanical Properties of Fasteners Made of Carbon Steel and Bolts, Screws and Studs

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Chemical Composition, % by mass)	2500.0
6 (Vanadium, % by mass)	500.0
6 (Molybdenum, % by mass)	500.0
6 (Nickel, % by mass)	500.0
6 (Chromium, % by mass)	500.0
6 (Lead, % by mass)	500.0
9.1.4 (Wedge Load test as per IS 1367 Part 3)	3000.0
1.2 (Uniformity of Zn coating)	1000.0
1.1 (Mass of Zinc Coating)	2000.0
9.7.1b (Percentage Elongation after fracture on Machined test piece, %.)	1000.0
9.7.1a (Yield Strength on Machined test piece, MPa.)	1000.0
9.7.1 (Tensile Strength on Machined test piece, MPa.)	1000.0
7 (Mechanical and physical properties (Hardness,Vickers))	2000.0
7 (Mechanical and physical properties (Proof load test))	2000.0
6 (Chemical Composition, % by mass)	2500.0
0 (Shear Strength Test)	3000.0
6 (Silicon)	500.0
6 (Manganese)	500.0
2 (Dimensions)	1000.0

3146

National Test House (NR), Ghaziabad

ASTM B117 - Salt spray for 3000 hrs ASTM B117

Salt spray for 3000 hrs ASTM B117

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASTM B 117 (Salt Fog Test 5% Nacl solution(for 96 hrs) ASTM 117B/IEC 60512-11-6 AS PER CLAUSE NO. 7.4.9 FOR INTER VEHICULAR COUPLER UNIT 500AMP AS PER RDSO SPEC. NO. RDSO/PE/SPEC/AC/0177-(REV-01)-2013)	5000.0
ASTM D 3359 (Cross Cut Test on Painted or Coated Specimen)	2000.0
ASTM B 117 (Salt Fog Test 5% Nacl solution(for 96 hrs) ASTM 117B/IEC 60512-11-6 AS PER CLAUSE NO. 7.4.9 FOR INTER VEHICULAR COUPLER UNIT 500AMP AS PER RDSO SPEC. NO. RDSO/PE/SPEC/AC/0177-(REV-01)-2013)	5000.0
ASTM D 3359 (Cross Cut Test on Painted or Coated Specimen)	2000.0

3147

National Test House (NR), Ghaziabad

ASTM D6637 (2015) - Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method

Standard Test Method for Determining Tensile Properties of Geogrids by the Single or Multi-Rib Tensile Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Method-A (Tensile Strength)	1500.0
Method-A (Elongation at break)	1500.0
Firm's Requirement (Secant Modulus)	2000.0

3148

National Test House (WR), Mumbai

A118.3 (1999) - American National Standard Specification for Chemical Resistant Water Cleanable Tile Setting Grouting Epoxy / Epoxy Adhesive

American National Standard Specification for Chemical Resistant Water Cleanable Tile Setting Grouting Epoxy / Epoxy Adhesive

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
E 5.1 (Test for Water Cleanability (Cl E-5.1, ANSI A118.3))	2000.0
E-5.2 (Setting Time and Service Time (Cl E-5.2, ANSI A 118.3))	2000.0
E-5.3 (Test for Shrinkage (Cl E-5.3, ANSI A118.3))	1000.0
E-5.4 (Test for Sag in Vertical Joints (cl 5.4, ANSI A 118.3))	4000.0
E-5.5 (Test for Bond Strength to Quarry Tile (Cl. E-5.5, ANSI A118.3))	9000.0
E-5.6 (Test for Compressive Strength of the cured material (ASTM C 579))	4000.0
E-5.7 (Test for Tensile Strength of the cured material (ASTM C 379))	4000.0
E-5.8 (Test for Thermal Shock (Cl. E-5.8, ANSI A 118.3)))	6000.0
ASTM (Mix Density)	1000.0
Manufacturer Specification (Pot Life (Manufacturer Specified method))	1000.0
Manufacturer Specification (Resistance to intermitted upto 70 Deg C.)	2000.0
ANSI A118.4, H-4.4 (Water Absorption Test (on the lines of ANSI A118.6, Cl. H-4.4))	2000.0

3149

National Test House (NR), Ghaziabad

AASHTO T 166 (2021) - AASHTO T 166-Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated Surface-Dry Specimens

AASHTO T 166-Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated Surface-Dry Specimens

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
AASHTO T 166 (Bulk specific gravity)	2000.0

3150

National Test House (WR), Mumbai

EN / ASTM - Flexible Sheet for Water Proofing / Modified Bituminous sheet materials

Flexible Sheet for Water Proofing / Modified Bituminous sheet materials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
EN 1849-2: 2019, Clause 5 (Thickness (EN 1849-2: 2019, Clause 5), mm)	1000.0
EN 1849-2: 2019, Clause 6 (Mass per Unit area (EN 1849-2: 2019, Clause 6), g/Sq.m)	1000.0
EN 12311-1: 1999, Clause 1-10 (Tensile Force (EN 12311-1: 1999, Clause 1-10), N/5cm)	2000.0
EN 12311-1: 1999, Clause 1-10 (Elongation (EN 12311-1: 1999, Clause 1-10), %)	2000.0
ASTM D5147-14 Clause No. 12 (Low Temperature Flexibility (ASTM D5147-14 Clause No. 12), Visual)	2000.0
ASTM D5147-14 Clause No. 8 (Tear Strength (ASTM D5147-14 Clause No. 8), N)	4000.0
ASTM D5147-14 Clause No. 16 (High Temperature Stability (ASTM D5147-14 Clause No. 16), °C)	1000.0
ASTM D5602-11 Clause No. 1-11 (Puncture Resistance (ASTM D5602-11 Clause No. 1-11), Visual)	2000.0
ASTM D36-14 Clause No. 1-12 (Softening point Of Bitumen (ASTM D36-14 Clause No. 1-12), °C)	1500.0
ASTM D5147-14 Clause No. 11 (Dimensional Stability(ASTM D5147-14 Clause No. 11), %)	2000.0