NTH - Management Information System

National Test House (ER), Alipore

Kolkata, Kolkata, West Bengal, 700027

- director-kol@nth.gov.in

Scope List

Reset

272 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

241

IRS:TC 30-05 (2006) - Underground railway jelly filled telecom quad cables for signalling & telecom installations

Underground railway jelly filled telecom quad cables for signalling & telecom installations

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.5.1 (Physical tests for conductor - Dimensions)	500.0
5.7 (Test for thickness of insulation and sheaths)	1000.0
5.8.2.3 (Physical tests for pe insulation, pe inner sheath, pvc intermediate and outer sheath - Shrinkage Test)	500.0
5.9.3 (Conductor resistance test)	1500.0
3.2.4 (Colour of insulated quad test)	500.0
5.9.1 (High voltage test)	3000.0
5.9.2.1 & 5.9.2.2 (Insulation Resistance Test)	3000.0
5.6.1 (Physical test for armour tapes - Dimensions)	1000.0
5.6.5 (Physical test for armour tapes - Test for closeness of armour)	1000.0
- (Testing on extra core of 24 Quad Cable)	46000.0
- (Testing of each extra core)	2000.0
5.6.1 (Dimensions (Armour Tape))	2000.0

242

NFC 33 040-2013 - Insulated Cable & their Accessories for Power System

Insulated Cable & their Accessories for Power System

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.7 (Corrosion test)	60000.0

243

PGCIL SFQP No.: Doc No. C/FQA/SFQP/SCW REV.06 dated:03.08.2020 (2020) - Specification ( Test on Stone Gravel) Power Grid Corporation of India Ltd.

Specification ( Test on Stone Gravel) Power Grid Corporation of India Ltd.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.6 (Measurement of Resistivity of Gravel)	20000.0

244

C/QA&I/SFQP/SCW, Rev.4 dated 29.01.2016 (2016) - Measurement of Resistivity of Gravel20/40mm

Measurement of Resistivity of Gravel20/40mm

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Measurement of Resistivity of Gravel)	20000.0

245

RDSO Specification no.RDSO/PE/SPEC/AC/0177(Rev.01)-2013 - SPECIFICATION FOR HIGH CAPACITY INTER VEHICULAR (IV) COUPLER UNIT. (500 AMPS. RATING)

SPECIFICATION FOR HIGH CAPACITY INTER VEHICULAR (IV) COUPLER UNIT. (500 AMPS. RATING)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.4.13 (Test for Withstanding Shock & Vibration)	70000.0

246

IS 9000 : Part 8 (1981) - Basic environmental testing procedures for electronic and electrical items: Part 8 vibration (Sinusoidal) test

Basic environmental testing procedures for electronic and electrical items: Part 8 vibration (Sinusoidal) test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
NA (Frequency Range : 5 Upto 3000Hz)	15000.0

247

IEC 61373 (2010) - Vibration/Shock Test

Vibration/Shock Test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8[ Cat. 1 Class A] (Functional random vibration test)	15000.0
10 (Shock Test in Cat. 1 Class A & B)	10000.0
9[ Cat 1,Class A] (Simulated long-life testing at increased random vibration levels in Cat. 1 Class A)	45000.0
8[ Cat. 1 Class B] (Functional random Vibration Test in Cat. 1 Class B)	15000.0
9[ Cat 1,Class B] (Simulated long-life testing at increased random vibration levels)	45000.0

248

IS 15549 ,Reaffirmed 2020 (2005 Reaffirmed 2020) - Stationary valve regulated lead acid batteries - Specification

Stationary valve regulated lead acid batteries - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 to 4.9 and 8.1 (Visual Examination)	20000.0
12.1 (Test for C10 Capacity and Voltage during discharge)	20000.0
12.2 (Test for C1 Capacity and Voltage during discharge)	20000.0
12.4 &12.5 (Ampere-hour and watt hour efficiency test)	10000.0
12.6 (Test for retention of charge)	10000.0
12.9 (Test for Oxygen recombination efficiency test)	15000.0
12.1 (Endurance Life Cycle Test)	80000.0
NA (Checking of dimension as per Manufacturer drawing)	500.0

249

IS 6304 (1992) - Stationary batteries - Lead - Acid type - With pasted positive plates - Specification (Second Revision)

Stationary batteries - Lead - Acid type - With pasted positive plates - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1,4.2,4.5,4.7&4.11 (Physical Verification)	25000.0
6 (Physical Verification)	500.0
8.6 (Capacity)	20000.0
8.7 (Capacity)	10000.0
8.8.1 (Ampere- Hour Efficiency)	7500.0
8.8.2 (Watt Hour Efficiency)	7500.0
8.9 (Capacity)	45000.0

250

JISC 8702 : 2009 - Small- sized valve regulated lead-acid batteries

Small- sized valve regulated lead-acid batteries

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 of JISC 8702-1:2009 (Capacity at 20 hr rate)	20000.0
5.3 of JISC 8702-1:2009 (Cycle service Endurance)	200000.0
5.4 of JISC 8702-1:2009 (Storage characteristic Test)	20000.0
5.2 of JISC 8702-1:2009 (High rate discharge characteristics)	20000.0
5.5 of JISC 8702-1:2009 (Maximum permissible current Characteristic)	15000.0
5.6 of JISC 8702-1:2009 (Charge Acceptance characteristic after deep discharge.)	15000.0
5.7 of JISC 8702-1:2009 (Endurance in Trickle application)	100000.0
5.8 of JISC 8702-1:2009 (Endurance in trickle application at 40 Deg C)	130000.0
5.11 of JISC 8702-1:2009 (Vibration Resistance Characteristics)	15000.0
5.9.b of JISC 8702-1:2009 (Gas emission intensity II)	15000.0
5.10.b of JISC 8702-1:2009 (Gas recombinating characteristic - Liquid leakage resistance characteristics)	15000.0

251

IS 16270 (2023) - Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Rated Capacity)	20000.0
8.2 (Endurance Test)	80000.0
8.3 (Charge retention test)	10000.0
8.4 (Cycling Endurance in photovoltaic application( Extreme Conditions))	90000.0
8.5 (Recovery from sulphation Test)	10000.0
8.6 (Water loss Test)	10000.0
8.1 (Rated Capacity Test (1000Ah))	40000.0
8.2 (Endurance Test (1000Ah))	160000.0
8.3 (Charge retention test (1000Ah))	20000.0
8.4 (Cycling Endurance in photovoltaic application( Extreme Conditions) (1000Ah)))	180000.0
8.5 (Recovery from sulphation Test (1000Ah))	20000.0
8.6 (Water loss Test (1000Ah))	20000.0
8.1 (Long Duration Capacity Test)	20000.0

252

IRS:S88/2004 (2004) - LOW MAINTENANCE LEAD ACID STATIONARY SECONDARY CELLS FOR S&T INSTALLATIONS

LOW MAINTENANCE LEAD ACID STATIONARY SECONDARY CELLS FOR S&T INSTALLATIONS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2 (Verification of constructional Requirements)	500.0
7.3 (Verification of Marking)	500.0
7.4 (Verification of dimension)	500.0
7.5 (Test for Capacity)	20000.0
7.6 (Test for loss of capacity on storage)	10000.0
7.7 (Endurance Test)	45000.0
7.8 (Ampere Hour & Watt Hour Efficiency Test)	20000.0
7.9 (Test for voltage during discharge)	5000.0
7.10 (Life Test)	240000.0
7.11 (Storage Test)	10000.0
7.12 (Water loss Test)	5000.0
7.13 (Equilibrium Float Current Test)	5000.0
7.14 (Sulphation Test)	20000.0
7.15 (Air Pressure Test on containers consisting of finished cell/Battery)	10000.0

253

IEC 60896 : Part 21-22 (2004) - Stationary Lead Acid Batteries Valve Regulated Type

Stationary Lead Acid Batteries Valve Regulated Type

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Gas Emission Test)	30000.0
6.6 (Content and durability of required marking)	500.0
6.2 (High Current tolerance Test)	20000.0
6.7 (Material Identification)	3000.0
6.11 (Discharge Capacity)	60000.0
6.12 (Charge retention during Storage)	50000.0
6.13 (Float Service with daily discharges)	30000.0
6.14 (Recharge behaviour)	30000.0
6.15 (Service Life at an operating temp. at 40 Deg C)	300000.0
6.16 (Impact of a stress temperature of 50Deg C or 60 Deg C)	250000.0
6.17 (Abusive over discharge)	60000.0
6.19 (Low temperature sensitivity)	30000.0

254

IS 5154(Part 1 & 2): 2013 (2013) - Lead Acid Traction Batteries

Lead Acid Traction Batteries

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.4 (1 h High rate discharge performance test)	20000.0
5.2 of IS 5154(Part-1)-2013 (5 h Capacity Test)	25000.0
5.5 of IS 5154 (Part-1)-2013 (Cyclic Endurance Test)	90000.0
3 and 5 of IS 5154(Part-2)-2013 (Dimensions of Traction Batteries)	1000.0
5.3 (Charge retention test)	20000.0

255

IS:1554 ( Part 1 ) - 1988 (1988) - SPECIFICATION FOR PVC INSULATED ( HEAVY DUTY ) ELECTRIC CABLES

SPECIFICATION FOR PVC INSULATED ( HEAVY DUTY ) ELECTRIC CABLES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1(a).(1),15.2(a) (Annealing test ( for copper ))	1000.0
15.2(b),15.1(a).(2) (Tensile test ( for aluminium ))	1000.0
15.1(a).(3),15.2(c) (Wrapping test ( for aluminium ))	500.0
15.1(a).(4),15.2(d),15.3(a) (Conductor resistance test)	2000.0
15.2(e),15.1(c) (Test for thickness of insulation and sheath)	1000.0
15.2(f), (Tensile strength and elongation at break of insulation and sheath)	1000.0
15.2(g),15.1(e) (Insulation resistance test)	1500.0
15.2(h),15.1(g) (High voltage test at room temperature)	1000.0
15.1.1 , 15.2.1 (Oxygen index test)	5000.0
15.1.1 , 15.2.1 (Temperature index)	5000.0
15.1.1 , 15.2.1 (Flame retmdance test on single cable)	5000.0
15.1.1 (Flame retardance test on bunched cables)	5000.0
15.1.1 , 15.2.1 (Test for halogen acid gas evolution)	5000.0
15.1.1 , 15.2.1 (Smoke density)	5000.0
15.1(b) (Test for armouring wires/strips-Dimension)	1000.0
15.1(b) (Test for armouring wires/strips - Tensile strength)	1000.0
15.1(b) (Test for armouring wires/strips - Elongation at break)	1000.0
15.1(b) (Test for armouring wires/strips - Torsion test for round wires)	1000.0
15.1(b) (Test for armouring wires/strips - Winding test for formed wires)	1000.0
15.1(b) (Test for armouring wires/strips - Uniformity of zinc coating)	1000.0
15.1(b) (Test for armouring wires/strips - Mass of zinc coating)	2000.0
15.1(b) (Test for armouring wires/strips - Resistivity)	2000.0
15.1(d) (Physical tests for insulation and outer sheath: - Tensile strength and elongation at break)	1500.0
15.1(d) (Physical tests for insulation and outer sheath: - Ageing in air oven)	2000.0
15.1(d) (Physical tests for insulation and outer sheath: - Shrinkage test)	500.0
15.1(d) (Physical tests for insulation and outer sheath: - Hot deformation)	500.0
15.1(d) (Physical tests for insulation and outer sheath: - Loss of mass in air oven)	1500.0
15.1(d) (Physical tests for insulation and outer sheath: - Heat shock test)	500.0
15.1(d) (Physical tests for insulation and outer sheath: - Thermal stability)	1000.0
15.1(f) (High voltage test ( water immersion test ))	3000.0
15.1(h) (Flammability test)	500.0
- (Test on 2nd core)	2000.0
- (Test on 3rd core)	2000.0
- (Test on 4th core)	2000.0

256

IS 7098 : Part 1 : 1988 (Reaffirmed Year : 2020), Amendments : 5 - Crosslinked polyethylene insulated PVC sheathed cables: Part 1 For working voltage up to and including 1100 V

Crosslinked polyethylene insulated PVC sheathed cables: Part 1 For working voltage up to and including 1100 V

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1.a.i , 15.2.a (Tests on Conductor - Annealing Test (for copper))	1000.0
15.1.a.ii , 15.2.b (Tests on Conductor - Tensile Test (for Aluminium))	1000.0
15.1.a.iii , 15.2.c (Tests on Conductor - Wrapping Test (for Aluminium))	500.0
15.1.a.iv , 15.2.d (Tests on Conductor - Resistance Test)	2000.0
15.1.b.1 (Test for round steel wire/formed steel wire(strip) armour - Dimensions)	500.0
15.1.b.2.i (Test for round steel wire/formed steel wire(strip) armour - Tensile Strength)	1000.0
15.1.b.2.ii (Test for round steel wire/formed steel wire(strip) armour - Elongation at Break)	1000.0
15.1.b.2.iii (Test for round steel wire/formed steel wire(strip) armour - Torsion test for round wires)	1000.0
15.1.b.2.iv (Test for round steel wire/formed steel wire(strip) armour - winding test for formed wires)	1000.0
15.1.b.2.v (Test for round steel wire/formed steel wire(strip) armour - Uniformity of zinc coating)	1000.0
15.1.b.2.vi (Test for round steel wire/formed steel wire(strip) armour - Mass of zinc coating)	2000.0
15.1.b.2.vii (Test for round steel wire/formed steel wire(strip) armour - Resistivity)	2000.0
15.1.c , 15.2.e (Test for thickness of insulation and sheath)	1000.0
15.1.d.i , 15.2.g (Physical test for insulation - Tensile strength and elongation at breakj)	1500.0
15.1.d.ii (Physical test for insulation - Ageing in oven)	2000.0
15.1.d.iii , 15.2.f (Physical test for insulation - Hot set test)	1000.0
15.1.d.iv (Physical test for insulation - Shrinkage test)	1000.0
15.1.d.v (Physical test for insulation - Water absorption test (gravimetric)))	1000.0
15.1.e.i , 15.2.g (Physical tests for outer sheath - Tensile strength and elongation at break)	1000.0
15.1.e.ii (Physical tests for outer sheath - Ageing in air oven)	1000.0
15.1.e.iii (Physical tests for outer sheath - Loss of mass in air oven)	1000.0
15.1.e.iv (Physical tests for outer sheath - Shrinkage test)	500.0
15.1.e.v (Physical tests for outer sheath - Hot deformation test)	500.0
15.1.e.vi (Physical tests for outer sheath - Heat shock test)	500.0
15.1.e.vii (Physical tests for outer sheath - Thermal stability)	1000.0
15.1.f , 15.2.j (Insulation resistance (Volume resistivity test))	2000.0
15.1.g , 15.2.h (High voltage test)	2000.0
15.1.h (Flammability test)	500.0
15.1.1.C1.a , 15.1.1.C2.a , 15.2.1.C1.a , 15.2.1.C2.a (Oxygen Index Test (for Category C1 & C2))	5000.0
15.1.1.C1.b , 15.1.1.C2.b , 15.2.1.C1.b , 15.2.1.C2.b (Flame retardance test on single cable (for category C1 & C2))	5000.0
15.1.1.C1.c , 15.1.1.C2.c , (Flame retardance test on bunched cable)	5000.0
15.1.1.C1.d , 15.1.1.C2.g (Temperature Index)	5000.0
15.1.1.C2.e (Smoke density)	5000.0
15.1.1.C2.f , 15.2.1.C2.d (Test for halogen acid gas evolution)	5000.0
- (Test on 2nd Core)	2000.0
- (Test on 3rd Core)	2000.0
- (Test on 4th Core)	2000.0
- (Test on 5th Core)	2000.0
- (Test on 6th Core)	2000.0
- (Test on 7th core)	2000.0
- (Test on 8th Core)	2000.0
15.4(a) (Cold bend test for outer sheath)	1500.0
15.4(b) (Cold Impact Test for outer sheath)	1500.0
15.4(c) (Resistance Test for armour (other than mining cable) (Optional Test))	1500.0

257

IS 14257 (2019) - Lead - Acid storage batteries for motor vehicles with light weight and high cranking performance - Specification (First Revision)

Lead - Acid storage batteries for motor vehicles with light weight and high cranking performance - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.3.1 (Physical Examination)	20000.0
9.3.2 (Dimensions and layout)	500.0
9.3.3 (Marking)	500.0
9.3.4 (5-hr capacity Test)	20000.0
9.3.5 (High rate discharge test at -15℃)	20000.0
9.3.6 (Cold cranking Ampere at -18℃)	20000.0
9.3.7 (Reserve Capacity Test)	20000.0
9.3.8 (Charge Acceptance test)	15000.0
9.3.9 (water loss in percent)	10000.0
9.3.10 (Charge retention test)	5000.0
9.3.11 (Light load Endurance test)	30000.0
9.3.12 (Life cycle test)	50000.0
9.3.13 (Over-charge Endurance test)	5000.0
9.3.14 (Electrolyte retention test)	5000.0
9.3.15 (Vibration resistance test)	10000.0
9.3.16 (Strength of terminal test)	5000.0
9.3.17 (Robustness to fastening test)	5000.0
Annex. B-1.2 (Residual Capacity Test)	10000.0

258

IS 7372 (1995) - Lead - Acid storage batteries for motor vehicles - Specification (First Revision)

Lead - Acid storage batteries for motor vehicles - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.3 (Physical Examination)	20000.0
9.4 (Dimensions and layout)	500.0
9.5 (Marking)	500.0
9.6 (Air Pressure Test)	10000.0
9.7 (Capacity Test)	25000.0
9.9 (High rate discharge test at Normal Temperature)	15000.0
9.10 (High rate discharge test at Low Temperature)	20000.0
9.12 (Retention of Charge Test)	15000.0
9.13 (Resistance to Over Charge Test)	10000.0
9.14 (Life Test)	60000.0
9.15 (Storage Test)	25000.0
9.8 (Vibration Test)	10000.0

259

IS 2026 : Part 11 (2021) - Power Transformers Part 11 Dry-Type Transformers

Power Transformers Part 11 Dry-Type Transformers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl No 14.2.5 (Applied Voltage Test)	2500.0
14.2.6 (Induced Voltage Withstand Test)	4000.0
14.2.4 (Measurement of No Load Loss & Current)	6000.0
14.2.3 (Measurement of Short Circuit Impedance and Load Loss)	8000.0
14.2.2 (Measurement of Voltage Ratio and Check of phase Displacement)	2000.0
14.2.1 (Measurement of Winding Resistance)	1000.0
14.3.2 (Temperature Rise Test)	40000.0
Cl. 21.2(e) of IS 1180 (Part 1) (Measurement of Insulation resistance)	1500.0

260

JIS D 5301:2006 - Lead Acid starter Batteries

Lead Acid starter Batteries

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

261

IS 694 (2010) - Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 1100 v (Fourth Revision)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 1100 v (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 1.i.a, ii.d , iii.a.4 (Conductor Resistance)	1500.0
Table 1. iii. a.1 , ii.a (Annealing Test (for copper))	1000.0
Table 1. iii. a.2 , ii.b (Tensile Test for aluminium)	1000.0
Table 1. iii. a.3 , ii.c (Wrapping Test (for Aluminium))	500.0
Table 1. iii. a.5 (Persulphate Test (for tinned copper conductor only)))	1000.0
Table 1. iii. b , ii.e (Tests for overall dimension and thickness of insulation/sheath)	1000.0
Table 1. iii. c.6 (Physical tests for insulation - Hot deformation Test)	500.0
Table 1. iii. c.1, ii.f (Physical tests for insulation- Tensile strength and elongation at break)	1500.0
Table 1. iii. c.2 (Physical tests for insulation - Loss of mass test)	1500.0
Table 1. iii. c.3 (Physical tests for insulation - Ageing in air oven)	2000.0
Table 1. iii.c.4 (Physical tests for insulation - Shrinkage test)	1000.0
Table 1. iii.c.5 (Physical tests for insulation - Heat shock test)	1000.0
Table 1. iii.c.7 (Physical tests for insulation - Thermal stability test)	1000.0
Table 1. iii. e.5, ii.j (Flammability Test)	500.0
Table 1. iii. c.11 , ii.k (Physical tests for insulation - Oxygen index test)	5000.0
Table 1. iii. c.12 , ii.m (Physical tests for insulation - Test for temperature index)	5000.0
Table 1. iii. c.13 , ii.n (Physical tests for insulation - Test for halogen acid gas evaluation)	5000.0
Table 1. iii. c.14 , ii.p (Physical tests for insulation - Test for smoke density rating)	5000.0
Table 1. iii. d.1 (Physical tests for sheath - Tensile strength and elongation at break)	1500.0
Table 1. iii. d.2 (Physical tests for Sheath - Loss of mass Test)	1500.0
Table 1. iii. d.3 (Physical tests for sheath - Ageing in air oven)	2000.0
Table 1. iii. d.4 (Physical tests for sheath - Shrinkage Test)	500.0
Table 1. iii. d.5 (Physical tests for sheath - Heat shock Test)	500.0
Table 1. iii. d.6 (Physical tests for sheath - Hot deformation Test)	500.0
Table 1. iii. d.7 (Physical tests for sheath - Thermal stability)	1000.0
Table 1. iii. d.8 (Physical tests for sheath - Oxygen Index Test)	5000.0
Table 1. iii. d.9 (Physical tests for sheath - Test for temperature Index)	5000.0
Table 1. iii. d.10 (Physical tests for sheath - Halogen acid gas evaluation)	5000.0
Table 1. iii. d.11 (Physical tests for sheath - Test for smoke density)	5000.0
Table 1. iii. e.1 (High Voltage Test (Water immersion Test))	3000.0
Table 1. iii. e.2 , ii.h (High voltage test or Spark test)	1500.0
Table 1.iii.e.3 , ii.g (Insulation resistance)	2000.0
Table 1. iii. e.4 (High voltage test (Cl. 10.2)(at room temperature))	1500.0
Table 1. iii. e.6 (Addition Ageing test (OU Cables only))	2000.0
- (Test on 2nd core)	2000.0
- (Test on 3rd core)	2000.0
- (Test on 4th core)	2000.0

262

IS/IEC : 60529 (2001 reaff : 2019) - Degree of Protection Provided by Enclosure(IP CODE)

Degree of Protection Provided by Enclosure(IP CODE)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13.2 First Characteristic Numeral 1 (Protection against solid foreign object of 50mm dia and greater,First Characteristic Numeral 1, cl 13.2)	7500.0
13.2 First Characteristic Numeral 2 (First Characteristic Numeral 2,Protection against solid foreign objects of 12.5 mm dia and greater.)	7500.0
13.2 First Characteristic Numeral 3 (First Characteristic Numeral 3, Protection against solid foreign objects of 2.5 mm dia and greater.)	7500.0
13.2 First Characteristic Numeral 4 (Protection against solid foreign objects of 1.0 mm dia and greater,First Characteristic Numeral 4)	7500.0
13.4/13.5 First Characteristic Numeral 5 (Dust Protected)	7500.0
13.4/13.5 First Characteristic Numeral 6 (No ingress of Dust)	7500.0
14.2.1 Second Characteristic Numeral 1 (Protected against vertically falling water drops)	7500.0
14.2.2 Second Characteristic numeral 2 (Protection against vertically falling water drops when enclosure tilted upto 15 degree)	7500.0
14.2.3 second characteristic numeral 3 (14.2.3 second characteristic numeral 3 :Protected against spring water)	7500.0
14.2.4 Second characteristic numeral 4 (14.2.4 Second characteristic numeral 4 :Protected against splashing water)	7500.0
14.2.5 Second characteristic numeral 5 (Protection against water Jets,14.2.5 Second characteristic numeral 5)	7500.0
14.2.6 Second characteristic numeral 6 (14.2.6 Second characteristic numeral 6 : Protected against powerful Jet)	7500.0
14.2.7, Second characteristic numeral 7 (14.2.7, Second characteristic numeral 7 :Protected against the effects of temporary immersion in water)	7500.0
14.2.8, Second Characteristic numeral 8 (Protection against the effects of continuous immersion in water:14.2.8, Second Characteristic numeral 8)	7500.0
Drawing Verification withe respect to dimension (Drawing Verification with respect to dimension)	3000.0

263

IS 2026 : Part 1 (2011) - Power Transformers: Part 1 General (Second Revision)

Power Transformers: Part 1 General (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1.2(a) (Temp Rise)	20000.0
10.1.3(d) (Measurement of Zero phase sequence impedance for 3 Phase transformer)	3000.0
10.1.1(a) (Windlng Resistance)	1600.0
10.1.1(b) (Voltage ratio & Phase Displacement)	3200.0
10.1.3(g) (Measurement of Hormonices of the no load current)	10000.0
10.1.1(d) (No Load loss and current)	9600.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	3000.0
10.1.1(e) (Induced Overvoltage)	6400.0
10.1.3 (f) (Noise Level)	10000.0
10.1.1(e) (AC voltage withstand test)	4000.0
10.1.1 (C) (% impedance and load loss)	12800.0
17.3.2 (a) of CBIP Pub. No. 317 (Vacuum Test - Type (Deflection))	10000.0
17.3.2 (b) of CBIP Pub. No. 317 (Oil Leakage Test (Pressure Test - Type))	10000.0
7 (Rating Plate Details)	-
7 (As per Specification)	-
CBIP Publication no. 317 (Polarization Index Test)	2500.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0

264

IS 101 part 6 sec 1 (1988) - "METHODS OF SAMPLING AND TEST FOR PAINTS, VARNISHES AND RELATED PRODUCTS" SALT SPRAY FOR 96 HRS.

"METHODS OF SAMPLING AND TEST FOR PAINTS, VARNISHES AND RELATED PRODUCTS" SALT SPRAY FOR 96 HRS.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

265

IS 2932 (2013) - Enamel, Synthetic, Exterior : (a) Undercoating (b) Finishing

Enamel, Synthetic, Exterior : (a) Undercoating (b) Finishing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

266

SLS 1126.1-2020 - Specification for Lead-Acid Starter Batteries[ Part 1: General Requirements & Method of Test]

Specification for Lead-Acid Starter Batteries[ Part 1: General Requirements & Method of Test]

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.4.2,9.10 (Cranking performance for dry charge batteries)	15000.0
9.1 (1st 20 h capacity Test)	25000.0
9.2 (1st Reserve Capacity Test)	20000.0
9.3.1 (cranking performance test)	20000.0
9.6.1.1 (Corrosion Test)	15000.0
9.6.2 (Endurance in cycle test)	45000.0
9.5 (charge retention test)	20000.0
9.4 (Charge Acceptance Test)	15000.0
9.9 (Electrolyte Retention Test)	10000.0
9.8 (Vibration Resistance Test)	15000.0
9.7 (Water consumption Test)	15000.0
9.6.1.2 (Endurance in cycle test)	55000.0
9.1 (2nd 20 h capacity Test)	25000.0
9.2 (2nd Reserve Capacity Test)	20000.0
9.1 (3rd 20 h capacity Test)	25000.0
9.2 (3rd Reserve Capacity Test)	20000.0
8.2 (Initial charge prior to test)	12000.0

267

JIS D 5302-2004 - Lead Acid Batteries for Motorcycles

Lead Acid Batteries for Motorcycles

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3.2 (Capacity (10 hour rate))	25000.0
8.3.3 (High Rate Discharge test)	15000.0
8.3.4 (Vibration resistance)	20000.0
Reference 1 (Deep Cycle Endurance)	60000.0
Reference 2 (Shallow Cycle Endurance)	60000.0
Reference 4 (Charge Retention test)	20000.0
Reference 3 (Characteristics of Electrolyte Decrease)	30000.0

268

IS 1652 (2013) - Stationary cells and batteries, lead - Acid type with plante positive plates - Specification (Fourth Revision)

Stationary cells and batteries, lead - Acid type with plante positive plates - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Verification of Constructional Requirements)	5000.0
7 (Verification of Marking)	2000.0
6.1 (Verification of Dimensions)	3000.0
10.6 (Test for Capacity)	25000.0
10.11 (Test for Voltage during Discharge)	10000.0
10.10 (Ampere-hour and watt hour efficiency test)	10000.0
10.8 (Test for loss of Capacity on Storage)	10000.0
10.9 (Endurance Test)	90000.0
10.12 (Loss of water test)	10000.0
10.13 (Test for suitability of floating battery operation)	10000.0
10.14 (Short circuit & Internal Resistance Test)	15000.0
- (Witness for Endurance Test)	13000.0

269

IS 13369 (1992) - Stationary lead - Acid batteries (With Tubular Positive Plates) in monobloc container - Specification

Stationary lead - Acid batteries (With Tubular Positive Plates) in monobloc container - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.2 (Verification of Constructional Requirements)	20000.0
11.3 (Verification of Marking)	1000.0
11.4 (Verification of Dimensions)	1000.0
11.5 (Test for Capacity)	20000.0
11.8 (Ampere-hour and watt hour efficiency test)	10000.0
11.6 (Test for loss of Capacity on Storage)	10000.0
11.7 (Endurance Test)	45000.0
11.9 (Water loss test)	10000.0
11.1 (Equilibrium Float current test)	10000.0
11.5 (Test for Capacity at -13 deg C to -15 deg C)	20000.0

270

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA) [1100 kVA to 2 500 kVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	20000.0
21.3(b) (Temperatur Rise Test)	40000.0
21.2(g) (Separate Source AC voltage withstand test)	2500.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	5000.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	7000.0
21.2(a) (Measurement of Winding Resistance)	1000.0
21.2(b) (Measurement of voltage ratio and,check ofvoltage vector relationship)	2000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	20000.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	1500.0
21.2(c) (Measurement of impedance voltage (principal tapping), shortcurcuit impedance and load loss (At 50% and 100% load))	8000.0
21.2(d) (Measurement of no Load and loss and current)	6000.0
21.2(f) (lnduced Over Voltage withstand test)	4000.0
21.4(a) (Determination of sound levels)	7000.0
21.4( e) (BDV of Oil in the tranformer)	10000.0
21.5.1.121.5.2.121.5.3.1 (Air Pressure (Type test)-Deflection)	20000.0
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	20000.0
As per CBIP Pub No. 317 Cl. 3.17 (Magnetic Balance Test)	5000.0
As per CBIP Manual No. 317 Cl. (Harmonics of No-load Current)	15000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	5000.0
N.A. (Unbalance Current)	5000.0