NTH - Management Information System

National Test House (ER), Alipore

Kolkata, Kolkata, West Bengal, 700027

- ssingh1@nth.gov.in

Scope List

Reset

237 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

Corrosion Test (Salt Spray Test) as per ASTM B117 & Customer specification - Corrosion Test (Salt Spray Test) as per ASTM B117 & Customer specification

Corrosion Test (Salt Spray Test) as per ASTM B117 & Customer specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Corrosion Test (Salt Spray Test) for 48 Hrs. as per ASTM B117 & Customer specification)	2500.0
2 (Drawing Identification)	1500.0

F-6C EIL Specification No. 6-79-0020 Rev.1 (2024) - F-6C Solvent less epoxy Coating

F-6C Solvent less epoxy Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-6B EIL Specification No. 6-79-0020 Rev.1 (2024) - F-6B Epoxy High Build Coating

F-6B Epoxy High Build Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-6A EIL Specification No. 6-79-0020 Rev.1 (2024) - F-6A Epoxy High Build Coating

F-6A Epoxy High Build Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-17 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-17 Novolac Epoxy Phenolic Coating Cured with Polyamine Adduct Hardener

F-17 Novolac Epoxy Phenolic Coating Cured with Polyamine Adduct Hardener

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.C)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-15 EIL Specification No. 6-79-0020 Rev.1 - F-15, Two Component Epoxy Phenolic Coating Cured with Polyamine adduct Hardener

F-15, Two Component Epoxy Phenolic Coating Cured with Polyamine adduct Hardener

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.C)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-12 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-12 Heat Resistance Silicon Aluminium paint

F-12 Heat Resistance Silicon Aluminium paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Therotical Covering capacity in sq.mt/coat/litres)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Over-coat interval)	1200.0
8 (Temperature Resistance (Min))	3000.0

F14 EIL Specification No. 6-79-0020 Rev.1 (2014) - F-14 Polyamine cure coal tar epoxy

F-14 Polyamine cure coal tar epoxy

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0

F-11 EIL Specification No. 6-79-0020 Rev.1 - F-11 Heat Resistance synthetic medium based Two pack Aluminium paint

F-11 Heat Resistance synthetic medium based Two pack Aluminium paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (.Therotical Covering capacity in sq.mt/coat/litres.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.C)	1200.0
7 (Over-coat interval)	1200.0
8 (Temperature Resistance (Min))	1200.0

F-9 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-9 Inorganic zinc silicate Coating

F-9 Inorganic zinc silicate Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg. C)	1200.0
7 (Pot Life at 30 deg.C for Two Component Paints)	1200.0
8 (Adhesion (ASTM D 4541))	5000.0
10 (Temperature Resistance (Min))	3000.0
9 (Over-coat interval)	1200.0

F-7 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-7 High build coal tar epoxy Coating

F-7 High build coal tar epoxy Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
3 (Therotical Covering capacity in sq.mt/coat/litres.)	1500.0
4 (Weight per Litres)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
2 (Dry Film Thickness)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

P-4 EIL Specification No. 6-79-0020 Rev.1 (2024) - P-4 Etch Primer/Wash Primer

P-4 Etch Primer/Wash Primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Therotical Covering Capacity)	1500.0
4 (Weight per Litres)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Over-coat interval)	1200.0

F-8 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-8 Self priming type Surface tolerant High build coal tar epoxy Coating

F-8 Self priming type Surface tolerant High build coal tar epoxy Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litres)	1500.0
4 (Weight per Litres)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-2 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-2 Acrylic Polyurethane Finish Paint

F-2 Acrylic Polyurethane Finish Paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litres.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg. C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Abrasion Resistance (ASTM D4060))	5000.0
12 (Temperature Resistance (Min) deg. c (ASTM D 2485))	3000.0

P-6 EIL Specification No. 6-79-0020 Rev. 1 - P-6 Epoxy Zinc Phosphate Primer

P-6 Epoxy Zinc Phosphate Primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Therotical Covering Capacity)	1500.0
4 (Weight per Litres)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Over-coat interval)	1200.0
8 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
9 (Adhesion (ASTM D 4541))	5000.0
10 (Temperature Resistance (Min))	3000.0

F-7 EIL SPECIFICATION for surface preparation & Protective coating System - High Build Coal Tar Epoxy Coating

High Build Coal Tar Epoxy Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Therotical Covering capacity in sq.mt/coat/litres.)	1500.0
4 (Weight per Litres)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

IS 101 (2015) - Determination of Volatile Organic Compound (VOC) Content gram per litre— Difference Method

Determination of Volatile Organic Compound (VOC) Content gram per litre— Difference Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3 (Volatile Organic Compound (VOC) Content gram per liter (on the lines of IS 101part2/Sec-1):1988 & IS 101 Part 2/Sec2):1986)	4000.0

IS 4606 (1983) - Specification for steel shots for use in foundries (First Revision)

Specification for steel shots for use in foundries (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.0 (Chemical Analysis (C, S, P, Si, Mn))	2500.0
9.0 (Microstructural Analysis)	3000.0
10.0 (Density)	1200.0
6 (Size-Sieve Analysis)	2000.0

High Polymer Cus specification (2003) - Wrapping Coating Material

Wrapping Coating Material

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.5 Viii (Solubility of coal tar based tape in petrol,% by mass C-2 SOLUBILITY OF COAL TAR BASED TAPE IN PETROL IS 15337:2003 RA 2018 (Annex c))	5000.0

Custom Standard For Epoxy Coating System. (2025) - Custom Standard For Epoxy Coating System.

Custom Standard For Epoxy Coating System.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1 25% NaOH Solution 2 30 % H2SO4 Solution 3 20 % HCL solution 4 Tap Water 5 Acetone 6 Ethanol 7 20% Acetic acid 8 Toluene 9 Carbon Tetra Chloride - CCL4 10 Cotton seed oil 11 20% KOH 12 20% Na2CO3 Solution)	14400.0

P-6 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - P-6 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name :Epoxy zinc phosphate primer

P-6 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name :Epoxy zinc phosphate primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	2000.0
2 (DFT per coat microns)	100.0
3 (Theoretical covering capacity in m sq/coat/litre)	1000.0
4 (Touch dry at 30 Deg c max (hours))	1000.0
5 (Hard dry at 30 deg C max(hours))	1000.0
6 (Over coating interval , hours)	1000.0
7 (Potlife at 30 deg C for 2 comp paints, hours)	1000.0
8 (Adhesion ASTM D 4541 (Mpa))	5000.0
9 (Temperature resistance min deg C 80 METHOD A ASTM D2485)	3000.0
10 (Non Volatile Matter % By mass Component-A (Base))	1000.0
11 (Non Volatile Matter % By mass Component-B (Hardener))	1000.0
12 (Volatile Matter % By mass Component-A (Base))	500.0
13 (Volatile Matter % By mass Component-B (Hardener))	500.0
14 (Specific Gravity Component-A (Base))	500.0
15 (Specific Gravity Component-B (Hardener))	500.0
16 (Ash content Component-A (Base))	1000.0
17 (Ash Content % By mass Component-B (Hardener))	1000.0
10 (weight per litre in kg/litre)	500.0
1 ()	-

IS 16676 (2017) - Solventless liquid epoxy system for application on interior and exterior surfaces of steel water pipeline - Specification

Solventless liquid epoxy system for application on interior and exterior surfaces of steel water pipeline - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Condition)	1200.0
6.2 (Thinning)	1200.0
6.3 (Application Properties)	1200.0
6.4 (Recoating Properties)	1200.0
6.5 (Consistency)	1200.0
6.7 Table 1 I (Thickness, dry film, Min)	1200.0
II (Electrical insulation (holidays))	2500.0
III (a) (Adhesion Test a)Tape Test)	1200.0
III (b) (Adhesion Test b)Pull off Test.)	2500.0
IV (a) (Immersion & vapour phase a) De-ionized water)	2000.0
IV (b) (Immersion & vapour phase b) Sulphuric acid pass 1 percent by weight.)	2000.0
IV (c) (Immersion & vapour phase c) Sodium hydroxide pass 1 percent by weight)	2000.0
V (Abrasion Resistance, Max)	2000.0
Vi (Cathodic Disbondment Test, Max)	2000.0
Vii (Solvent Rub Test)	1200.0
Viii (Drinking Water Test As per ANNEX)	5000.0
1 ()	-

IS 16719 (2022) - Polyurethane coatings for the interior and exterior of steel pipe and fittings - Specification

Polyurethane coatings for the interior and exterior of steel pipe and fittings - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
xii) (Flexibility (180º bend over 6.25 mm diameter rod))	1200.0
xi) (Salt Spray, 5 percent NaCl (see Note))	100000.0
ix) (Impact resistance, Min)	2500.0
viii) (Hardness, Min)	2500.0
viii) (Cathodic disbondment test, Max)	2500.0
vi) (Abrasion resistance, Max)	2500.0
v) (c) (c)Sodium hydroxide pass 1 percent by weight)	2500.0
v) (b) (b) Sulphuric acid pass 1 percent by weight)	2500.0
v) (a) (a) De-ionized water pass)	2500.0
iv) (b) (b) Pull off Test, Min)	2500.0
iv) (a) (a) Tape test)	1200.0
iii) (Electrical insulation (holidays))	2500.0
ii) (Thickness, dry film(Internal &External application))	1200.0
6.6 Table 1 i) (Drying time at 50 ºC, h, Max Tack free)	1200.0
6.5 (Lead Restriction)	2500.0
6.3 (Consistency)	1200.0
6.2 (Recoating Properties)	1200.0
6.1 (Application Properties)	1200.0

CUSTOMER SPECIFICATION PAINT LAB (0) - CUSTOMER SPECIFICATION PAINT LAB

CUSTOMER SPECIFICATION PAINT LAB

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Dry film thickness)	1200.0
9 (Gloss)	1200.0
7 (Pencil hardness test)	1500.0
6 (Impact resistance test)	1500.0
5 (Cross hatch adhesion test)	1500.0
10 (Salt Spray (ASTM B117) 100 hrs)	5000.0
8 (Bend Test)	1200.0

Custom Paint 2025 - Custom Paint System

Custom Paint System

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Pull out Test of paint coating on cementitious surface)	2000.0
2 (Accelerated Weathering Test for 96 hrs)	4800.0
3 (Water Permeability Test)	5000.0
4 (BS 476 Part 7 & Customers Specification)	10000.0

BS 476 part 7 (1997) - Classification of Surface spread of flame of products

Classification of Surface spread of flame of products

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Surface Spread of flame test ( BS 476 Part 7))	8000.0

EIL Specification for High build Paint System (2024) - EIL Specification for High build Paint System

EIL Specification for High build Paint System

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Specific gravity)	1200.0
2 (% Solid by weight)	1200.0
3 (% Zinc content ( in case of organic or inorganic zinc primer))	4000.0
4 (Drying time (Touch dry))	1200.0
5 (Drying time (Full Curing))	1200.0
6 (Pull of adhesion)	5000.0
7 (Flexibility and adhesion)	1200.0
8 (Pencil Hardness)	3000.0
9 (Storage Stability)	2000.0

AAI SPECIFICATION FOR RUNWAY MARKING PAINT (2023) - SPECIFICATION OF RUNWAY MARKING PAINT (White &Golden yellow

SPECIFICATION OF RUNWAY MARKING PAINT (White &Golden yellow

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Gloss at 45 (before wear))	500.0
2 (Gloss at 45 (After wear400 revolutions ))	2000.0
5 (Drying Time in minutes)	1200.0
6 (Residue on 63 microns sieve %)	1200.0
7 (Area coverage on standard Plate (new' surface) (Old surface) sqm/litre)	2000.0
8 (Consistency at 30 deg C(+/-) by Ford cup No B-4)	1500.0
9 (Density gm/cc)	1200.0

IS 15489 (2013) - Paint, plastic emulsion - Specification (First Revision)

Paint, plastic emulsion - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Accelerated Weathering Tests (Accelerated Weathering Tests (UV condensation type), IS 101 (Part 6/Sec 5): 1997 for 2000 hr)	100000.0

CUSTOM PAINT ONSITE TESTING-1 (2024) - CUSTOM PAINT ONSITE TESTING-1

CUSTOM PAINT ONSITE TESTING-1

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Distinctness of Image (DOI))	10000.0

1
2
3
Next
Last