NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1226 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

1051

IS 616 (2017) - Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Marking & Instructions)	500.0
7.1.1 (Heating under normal Operating Conditions, Accessible parts)	5000.0
7.1.3 (Parts other than windings, providing Electrical Insulation)	1000.0
7.1.4 (Parts acting as a support or a mechanical barrier & Winding)	1000.0
7.2 (Heat Resistance of insulating Material)	1000.0
8.1 to 8.16 (Constructional Requirements with regard to the Protection against Electrical Shock)	1000.0
8.17 (Requirement of Insulating winding wires for use without additional interleaved insulation)	500.0
8.18 (Endurance Test for wound components with insulated winding wires without additional interleaved insulation)	500.0
8.19.1,&8..19.2 (Disconnection from the mains)	1000.0
8.20 & 8.21 (Main Switch)	500.0
9.1.2 & 9.1.3 (Shafts of operating, Knobs , handles, levers and the like)	500.0
9.1.4 (Terminals)	500.0
9.1.5 (Preset Controls)	1000.0
9.1.6 (Withdrawal of main Plugs)	1000.0
9.1.7 (Resistance to external s-force)	1000.0
9.2 (Removal of protective cover)	500.0
10.2 (Surge Test)	10000.0
10.3 (humidity Treatment)	20000.0
10.4 (Insulation Resistance and Dielectric Strength)	500.0
11.1 (Electrical Shock Hazard)	500.0
11.2,11.2.1, 11.2.2,11.2.3,11.2.4,11.2.5, (Heating)	3000.0
12.1.3 (Vibration Test)	5000.0
12.1.4 (Impact Test)	500.0
12.1.5 (Drop Test)	500.0
12.1.6 (Stress Relief Test)	500.0
12.2 (Fixing of actuating Elements)	1000.0
12.3 (Remote Control devices held in hand)	500.0

1052

IS 1652 (2013) - Stationary cells and batteries, lead - Acid type with plante positive plates - Specification (Fourth Revision)

Stationary cells and batteries, lead - Acid type with plante positive plates - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Verification of Constructional Requirements)	5000.0
7 (Verification of Marking)	2000.0
6.1 (Verification of Dimensions)	3000.0
10.6 (Test for Capacity)	25000.0
10.11 (Test for Voltage during Discharge)	10000.0
10.10 (Ampere-hour and watt hour efficiency test)	10000.0
10.8 (Test for loss of Capacity on Storage)	10000.0
10.9 (Endurance Test)	90000.0
10.12 (Loss of water test)	10000.0
10.13 (Test for suitability of floating battery operation)	10000.0
10.14 (Short circuit & Internal Resistance Test)	15000.0

1053

IS 6304 (1992) - Stationary batteries - Lead - Acid type - With pasted positive plates - Specification (Second Revision)

Stationary batteries - Lead - Acid type - With pasted positive plates - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3,4.4,4.6,,4.8,4.9,4.10 &7 (Visual Inspection)	10000.0
4.1,4.2,4.5,4.7&4.11 (Physical Verification)	25000.0
6 (Physical Verification)	500.0
8.6 (Capacity)	20000.0
8.7 (Capacity)	10000.0
8.8.1 (Ampere- Hour Efficiency)	7500.0
8.8.2 (Watt Hour Efficiency)	7500.0
8.9 (Capacity)	45000.0
8.1 (Voltage during Discharge)	5000.0
9.8 (Voltage)	10000.0

1054

IS 14257 (2019) - Lead - Acid storage batteries for motor vehicles with light weight and high cranking performance - Specification (First Revision)

Lead - Acid storage batteries for motor vehicles with light weight and high cranking performance - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.3.1 (Physical Examination)	20000.0
9.3.2 (Dimensions and layout)	500.0
9.3.3 (Marking)	500.0
9.3.4 (5-hr capacity Test)	20000.0
9.3.5 (High rate discharge test at -15℃)	20000.0
9.3.6 (Cold cranking Ampere at -18℃)	20000.0
9.3.7 (Reserve Capacity Test)	20000.0
9.3.8 (Charge Acceptance test)	15000.0
9.3.9 (water loss in percent)	10000.0
9.3.10 (Charge retention test)	5000.0
9.3.11 (Light load Endurance test)	30000.0
9.3.12 (Life cycle test)	50000.0
9.3.13 (Over-charge Endurance test)	5000.0
9.3.14 (Electrolyte retention test)	5000.0
9.3.15 (Vibration resistance test)	10000.0
9.3.16 (Strength of terminal test)	5000.0
9.3.17 (Robustness to fastening test)	5000.0
Annex. B-1.2 (Residual Capacity Test)	10000.0

1055

IS 16270 (2023) - Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Rated Capacity)	20000.0
8.2 (Endurance Test)	80000.0
8.3 (Charge retention test)	10000.0
8.4 (Cycling Endurance in photovoltaic application( Extreme Conditions))	90000.0
8.5 (Recovery from sulphation Test)	10000.0
8.6 (Water loss Test)	10000.0

1056

IS 13369 (1992) - Stationary lead - Acid batteries (With Tubular Positive Plates) in monobloc container - Specification

Stationary lead - Acid batteries (With Tubular Positive Plates) in monobloc container - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.2 (Verification of Constructional Requirements)	20000.0
11.3 (Verification of Marking)	1000.0
11.4 (Verification of Dimensions)	1000.0
11.5 (Test for Capacity)	20000.0
11.8 (Ampere-hour and watt hour efficiency test)	10000.0
11.6 (Test for loss of Capacity on Storage)	10000.0
11.7 (Endurance Test)	45000.0
11.9 (Water loss test)	10000.0
11.1 (Equilibrium Float current test)	10000.0
11.5 (Test for Capacity at -13 deg C to -15 deg C)	20000.0

1057

IS 8662 (2004) - Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision)

Enamel, synthetic exterior: (A) undercoating (B) finishing, for railway coaches - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.6.xiii (Keeping properties)	5000.0
6.6.xii (Accelerated storage stability test, at 60 degC, 96 h)	3000.0
6.6.xi.b (Phthalic anhydride content of non-volatile vehicle)	3000.0
6.6.xi.a (Volume solids)	3000.0
6.6.x (Flash point)	1500.0
6.6.ix (Flexibility and adhesion)	1200.0
6.6.viii (Scratch hardness after 48 h air drying (1 000 g weight))	1500.0
6.6.vii (Water content (if suspected to be present) - IS 101 (Part 2/Sec 1))	1200.0
6.6.vi (Colour)	1200.0
6.6.v (Fineness of grind,)	1200.0
6.6.iv.b (Gloss , 60 deg)	1500.0
6.6.iv.a (Fnish)	1200.0
6.6.iii.d (Drying time Tack Free)	1200.0
6.6.iii.c (Hard dry at 70 DegC with 15 min flash- off time)	1200.0
6.6.iii.b (Drying time Hard Dry)	1200.0
6.6.iii.a (Drying time Surface Dry)	1200.0
6.6.ii (Mass, in kg/101itres)	1500.0
6.6.i.b (Viscosity byFord cup No. 4)	1200.0
6.6.i.a (Consistency)	1200.0
6.5 (Resistance to Alkali (for Finishing Only)	1500.0
6.4 (Resistance to Acid (for Finishing Only))	1500.0
6.3 (Durability( Normal Outdoor Exposer))	10000.0
6.2.6 (Application Properties)	1200.0
6.2.5 (Thinning Properties)	1200.0
6.2.4 (Skin Formation)	1200.0
6.2.3 (Freedom from Coarse Particles)	1200.0
6.2 (Condition in Container)	1200.0
6.1 (Composition)	1200.0

1058

IS 1651 (2013) - Stationary cells and batteries, lead - Acid type (With Tubular Positive Plates) - Specification (Fourth Revision)

Stationary cells and batteries, lead - Acid type (With Tubular Positive Plates) - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.3 (Verification of Marking)	2000.0
12.4 (Verification of Dimensions)	3000.0
12.5 (Capacity)	25000.0
12.10 (Test for Voltage during Discharge)	10000.0
12.9 (Ampere-hour and watt hour efficiency test)	10000.0
12.7 (Test for loss of Capacity on Storage)	10000.0
12.8 (Endurance Test)	90000.0
12.11 (Water loss test)	10000.0
12.12 (Test for suitability of floating battery operation)	10000.0
12.13 (Short circuit & Internal Resistance Test)	15000.0
12.2 (Verification of Constructional Requirements)	5000.0
12.13 (Short circuit & Internal Resistance Test(Current more than 1000 Amps))	15000.0

1059

IS 7372 (1995) - Lead - Acid storage batteries for motor vehicles - Specification (First Revision)

Lead - Acid storage batteries for motor vehicles - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.3 (Physical Examination)	20000.0
9.4 (Dimensions and layout)	500.0
9.5 (Marking)	500.0
9.6 (Air Pressure Test)	10000.0
9.7 (Capacity Test)	25000.0
9.9 (High rate discharge test at Normal Temperature)	15000.0
9.10 (High rate discharge test at Low Temperature)	20000.0
9.12 (Retention of Charge Test)	15000.0
9.13 (Resistance to Over Charge Test)	10000.0
9.14 (Life Test)	60000.0
9.15 (Storage Test)	25000.0
9.8 (Vibration Test)	10000.0

1060

IEC 61373 (2010) - Vibration/Shock Test

Vibration/Shock Test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8[ Cat. 1 Class A] (Functional random vibration test)	15000.0
9[ Cat 1,Class A] (Simulated long-life testing at increased random vibration levels in Cat. 1 Class A)	45000.0
10 (Shock Test in Cat. 1 Class A & B)	10000.0
9[ Cat 1,Class B] (Simulated long-life testing at increased random vibration levels)	45000.0
8[ Cat. 1 Class B] (Functional random Vibration Test in Cat. 1 Class B)	15000.0

1061

IS 1470 (1995) - Silicomanganese

Silicomanganese

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2.2 (Carbon)	1200.0
7.2.2 (Sulphur)	1200.0
7.2.2 (Phosphorus)	1200.0
7.2.2 (Silicon)	2000.0
7.2.2 (Manganese)	1200.0
7.2.2 (Arsenic )	2000.0
7.2.2 (Chromium + Nickel + Molybdenum )	3000.0
7.2.2 (Carbon)	1200.0
7.2.2 (Sulphur)	1200.0
7.2.2 (Phosphorus)	1200.0
7.2.2 (Silicon)	2000.0
7.2.2 (Manganese)	1200.0
7.2.2 (Arsenic )	2000.0
7.2.2 (Chromium + Nickel + Molybdenum )	3000.0
7.2.2 (Carbon)	1200.0
7.2.2 (Sulphur)	1200.0
7.2.2 (Phosphorus)	1200.0
7.2.2 (Silicon)	2000.0
7.2.2 (Manganese)	1200.0
7.2.2 (Arsenic )	2000.0
7.2.2 (Chromium + Nickel + Molybdenum )	3000.0

1062

IS 164 (2015) - Ready mixed paint for road marking - Specification (Second Revision)

Ready mixed paint for road marking - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.6.2.2 (Toxic metals as Pb Cd Cr: (Atomic Absorption Spectrophotometric methods))	2000.0
5.6.2.1 (Volatile Organic Compounds (VOC): (IS 101 (Part 2/Sec 1) and IS 101 (Part 2/Sec 2)))	3000.0
xii (Keeping properties (IS 101 (Part 6/Sec 2)))	5000.0
xi (Mass in kg/10 litre, (IS 101 (Part 1/Sec 7)))	500.0
x (Flash point (IS 101 (Part 1/Sec 6)))	600.0
ix (Residue on sieve, Max, (IS 101 (Part 8/Sec 1)))	500.0
viii-b (Resistance to wear a) For Grade 2 (as refer in IS 164))	1000.0
viii-a (Resistance to wear a) For Grade 1 (As refer in IS 164))	1000.0
vii (Recoating property (As refer in IS 164))	600.0
vi (Resistance to bleeding (As refer in IS 164))	500.0
v (Wet Opacity (IS 101 (Part 4/Sec 1)))	600.0
iv (Colour (IS 101 (Part 4/Sec 2)))	500.0
iii (Finish (IS 101 (Part 3/Sec 4)))	500.0
ii (Consistency (Annex D))	500.0
i (Drying time, Max b) Hard dry (IS 101 (Part 3/Sec 1)))	500.0
5.5 table 1 i (Drying time, Max a) Surface dry (IS 101 (Part 3/Sec 1)))	500.0
5.4 (Lead Restriction, Max, (IS 101 (Part 8/Sec 5)))	1200.0
5.3 (Durability (Annex C) 25 days)	2000.0
5.2 (Applications (Annex B))	500.0

1063

IS 158 (2015) - Ready mixed paint, brushing, bituminous, black, acid, alkali and heat resisting - Specification (Fourth Revision)

Ready mixed paint, brushing, bituminous, black, acid, alkali and heat resisting - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3,xvi (Keeping properties)	500.0
4.3,xv (Flash Point)	500.0
4.3,xiv (Resistance to heat)	200.0
4.3,xiii (Resistance to alkali)	1000.0
4.3,xii (Resistance to acid)	2000.0
4.3,xi (Volatile matter, percent by mass)	200.0
4.3,x (Protection against corrosion under conditions of condensation)	2000.0
4.3, ix (Stripping Test)	1000.0
4.3, viii (Flexibility and adhesion, bend test with 6.25 mm dia mandrel and type 1 apparatus)	1000.0
4.3,vii (Water Content,percent by mass)	100.0
4.3,vi (Mass, kg/10litre)	100.0
4.3,v (Colour)	100.0
4.3,iv (Wet opacity)	500.0
4.3,iii (Finish)	100.0
4.3,ii (Consistency)	1000.0
4.3,i (Drying time : Hard dry)	1000.0
4.2 (Lead Restrictions)	1500.0

1064

IS 2932 (2013) - Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.9,xiv (Wet opacity, (IS 101 (Part 4/Sec 1)))	1500.0
6.9,xiii (Keeping properties, (IS 101 (Part 6/Sec 2)))	5000.0
6.9,xii (Accelerated storage stability test, (Annex G))	400.0
6.9 (Wet Opacity)	200.0
6.9, (Colour)	300.0
6.9,ix.b (Composition: Phthalic Anhydride Content, (IS 101 (Part 8/Sec 4)))	350.0
6.9,ix.a (Composition: Volume solids, (IS 101 (Part 8/Sec 6)))	2000.0
6.9,viii (Flash point, (IS 101 (Part 1/Sec 6)))	350.0
6.9,vii.b (Flexibility and adhesion:Bend test (with 6.25 mm in type 1 apparatus), (IS 101 (Part 5/Sec 2)))	350.0
6.9,vii.a (Flexibility and adhesion:Scratch hardness (Load 1 000 g), (IS 101 (Part 5/Sec 2)))	1500.0
6.9, vi (Colour, (IS 101 (Part 4/Sec 2)))	350.0
6.9,v (Fineness of grind, microns (IS 101 (Part 3/Sec 5)))	350.0
6.9,iv.b (Gloss, 60º, (IS 101 (Part 3/Sec 4)))	350.0
6.9,iv.a (Finish, (IS 101 (Part 3/Sec 4)))	350.0
6.9,iii.c (Drying time: Tack free, (IS 101 (Part 3/Sec 1)))	350.0
6.9,iii.b (Drying time: Hard dry, (IS 101 (Part 3/Sec 1)))	1000.0
6.9,iii.a (Drying time: surface dry, (IS 101 (Part 3/Sec 1)))	1200.0
6.9,ii (Mass, kg/10litre (IS 101 (Part 1/Sec 7)))	1200.0
6.9,i.b (Viscosity by Ford cup No. 4 at 27 ± 2°C (IS 101 (Part 1/Sec 5)))	350.0
6.9,i. a (Consistency)	1200.0
6.8 (Lead Restriction, (IS 101 (Part 8/Sec 4)))	350.0
6.7.1.3 (Durability: Accelerated weathering test Xenon Arc (700hrs.) (Annex C-4))	35000.0
6.7.1.3 (Durability: Accelerated weathering test QUV apparatus (Lamp Type UV 313, Cycle UV 4 hrs and condensation 4 hrs) Total 360 hrs)	1000.0
6.7.1.1 (Durability (Normal outdoor exposure test) 12 Months (Annex C))	10000.0
6.6 (Application Properties)	350.0
6.5 (Thinning Properties)	350.0
6.4 (Skin formation)	350.0
6.3 (Freedom from Coarse Particles)	350.0
6.2 (Condition in Container)	350.0
6.1.1 (Composition)	350.0
6.1.2 (Total Non-Volatile Content (IS 101 Part 8/Sec 2))	500.0

1065

IS 5410 (2013) - Cement paint - Specification (Second Revision)

Cement paint - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.8 ix (Recoating properties)	1200.0
4.8 viii (Pot life of mixed paint)	1200.0
4.8 vii (Water repellency)	1200.0
4.8 vi (Resistance to dry rubbing)	1200.0
4.8 v (Residue on sieve % by mass)	1200.0
4.8 iv (Fastness to light (250hrs))	12500.0
4.8iii (Colour)	1200.0
4.8 ii (Finish)	1200.0
4.8 i (Drying time Hard dry)	1200.0
4.7 (Keeping properties)	5000.0
4.6 (Durability Normal Out Door exposure Test 18 Months)	15000.0
Cl 4.4 (Lead Restriction)	1200.0
Cl 4.1 (Composition)	3500.0

1066

IS 428 (2013) - Washable distemper - Specification (Third Revision)

Washable distemper - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.7 ix (ix)Acc storage stability)	1500.0
6.7 viii (viii) Resistance to alkali)	1000.0
6.7 Vii (vii) Recoating properties)	1000.0
6.7 Vi (vi) Residue on sieve % by mass)	200.0
6.7 v (v) Fastness to light 250 hrs)	12500.0
6.7 iv (iv) Colour)	500.0
6.7 iii (iii)Finish)	500.0
6.7 ii (ii) Consistency)	1000.0
6.7 i. (b) (Drying time b) Hard dry)	1500.0
6.7 i. (a) (Drying time a) surface dry)	1500.0
6.6 (Keeping properties)	5000.0
6.5 (Lead Restriction)	500.0
6.3 (Application)	500.0
6.2 (Thinning)	100.0
6.1 (Form and condition)	500.0
6.9.2.2 (toxic metals as lead, cadmium, chromium (VI) and their compounds)	1500.0
6.9.2.1 (volatile organic compounds % by mass)	2500.0

1067

IS 16098 Part 1 (2013) - Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

1068

IS 427 (2013) - Distemper, dry, colour as required - Specification (Third Revision)

Distemper, dry, colour as required - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3 (Lead Restriction)	500.0
4.2.2.ix (Resistance to dry rubbing IS 427 Annex F)	100.0
4.2.2.viii (Resistance to Alkali IS 427 Annex E)	100.0
4.2.2vii (Recoating properties IS 427 Annex D)	100.0
4.2.2.vi (Residue on sieve IS 427 Annex C)	100.0
4.2.2.v (Fastness to light 250 Hours Exposure Xenon arc Appartaus)	5000.0
4.2.2.iv (colour IS 101 (Part 4 /Sec 2))	100.0
4.2.2.iii (Finish IS 101 (Part 3/Sec 4))	100.0
4.2.2.ii (consistency IS 101 (Part 1/ Sec 5))	100.0
4.2.2 i (Drying Time Hard Dry)	200.0
4.1 (Form and Condtion)	100.0
Additional Parameters (Volatile Organic compound(VOC) S 101: Part 2/Sec 2 & Part 2/Sec 3)	3500.0
Additional Parameters (Toxic metals -- (as metal) Lead,, Chromium, Cadmium -- Atomic absorption spectrophotometer)	1500.0

1069

IS 110 (2017) - Ready mixed paint, brushing, grey filler, for enamels for use over primers - Specification (Third Revision)

Ready mixed paint, brushing, grey filler, for enamels for use over primers - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3xiii (Keeping properties)	5000.0
4.3 xii (Flash point)	1200.0
4.3 xi (Flexibility and adhesion:b)bend test with 6.25 mm dia mandrel Type I apparatus)	1200.0
4.3 xi (Flexibility and adhesion: a Scratch Hardness Test 1000 g)	1200.0
4.3x (Residue on sieve ,percent by mass)	1200.0
4.3ix (Wet opacity m2/10 litre)	1200.0
4.3 viii (hold out property)	1200.0
4.3 vii (Flattning Property)	1200.0
4.3vi (colour)	1200.0
4.3 v (Dry Film thickness per coat by brush in microns)	1200.0
4.3 iii (Mass, kg/10litre)	1200.0
4.3 ii (b) Viscosity by Ford Cup no 4 at 27 (+/-)2 deg C)	1200.0
4.3ii (a)Consistency)	1200.0
4.3 i (i) Drying time, h b) hard dry)	1200.0
4.3 i (i) Drying time, h, a) surface dry )	1200.0
4.2 (Lead Restrictions)	2500.0
4.1 (Composition)	1200.0

1070

IS 133 : Part 1 (2013) - Enamel, interior: (A) undercoating (B) finishing - Specification: Part 1 for household and decorative purposes (Fifth Revision)

Enamel, interior: (A) undercoating (B) finishing - Specification: Part 1 for household and decorative purposes (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.9, xiv (Keeping properties)	5000.0
5.9, viii (Fasteness to light)	5000.0
5.9,xiii (Accelerated storage stability test)	2000.0
5.9,xii (Volume solids percent)	1200.0
5.9,xi (Flash point)	1200.0
5.9,x,b (Flexibility and adhesion:Bend test with 6.25 mm dia Mandre in type 1 apparatus.)	1200.0
5.9,x,a (Flexibility and adhesion: Scratch hardness (Load 1 000 g), )	1200.0
5.9,ix (Resistance to water)	1200.0
5.9,vii (Wet opacity)	1200.0
5.9,vi (colour)	1200.0
5.9,v (Fineness of grind, microns)	1200.0
5.9, iv,b (Gloss, 60º)	1200.0
5.9,iv,a (Finish)	1200.0
5.9,iii b ( Viscosity by B 4 ford cup)	1200.0
5.9,iii a ( Consistency )	1200.0
5.9,ii (Mass, kg/10litre)	1200.0
5.9.i c (Drying time : Tack free)	1200.0
5.9.i b (Drying time : Hard dry)	1200.0
5.9.i a (Drying time : Surface dry)	1200.0
5.8 (Lead Restrictions)	2500.0
5.7 (Freedom from Yellowing)	1200.0
5.6 (Thinning Properties)	1200.0
5.5 (Skin formation)	1200.0
5.4 (Freedom from Coarse Particles)	1200.0
5.3 (Condtion in container)	1200.0
5.2 (Total Non-volatile content)	1200.0

1071

IS 9000 : Part V : Sec 2 (1981) - Electric and Electronics items (size less than 1 cubic meter)

Electric and Electronics items (size less than 1 cubic meter)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

1072

IS 9000 : Part II : Sec 2 (1977) - Electric and Electronics items (size less than 1 cubic meter)

Electric and Electronics items (size less than 1 cubic meter)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

1073

IS 9000 : Part 5 : Sec 1&2 (1981) - Electric and Electronics items (size less than 1 cubic meter)

Electric and Electronics items (size less than 1 cubic meter)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

1074

IS 694 (2010) - Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 1100 v (Fourth Revision)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 1100 v (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 1.i.a, ii.d , iii.a.4 (Conductor Resistance)	1500.0
Table 1. iii. a.1 , ii.a (Annealing Test (for copper))	1000.0
Table 1. iii. a.2 , ii.b (Tensile Test for aluminium)	1000.0
Table 1. iii. a.3 , ii.c (Wrapping Test (for Aluminium))	500.0
Table 1. iii. a.5 (Persulphate Test (for tinned copper conductor only)))	1000.0
Table 1. iii. b , ii.e (Tests for overall dimension and thickness of insulation/sheath)	1000.0
Table 1. iii. c.1, ii.f (Physical tests for insulation- Tensile strength and elongation at break)	1500.0
Table 1. iii. c.2 (Physical tests for insulation - Loss of mass test)	1500.0
Table 1. iii. c.3 (Physical tests for insulation - Ageing in air oven)	2000.0
Table 1. iii.c.4 (Physical tests for insulation - Shrinkage test)	1000.0
Table 1. iii.c.5 (Physical tests for insulation - Heat shock test)	1000.0
Table 1. iii. c.6 (Physical tests for insulation - Hot deformation Test)	500.0
Table 1. iii.c.7 (Physical tests for insulation - Thermal stability test)	1000.0
Table 1. iii. e.5, ii.j (Flammability Test)	500.0
Table 1. iii. c.11 , ii.k (Physical tests for insulation - Oxygen index test)	5000.0
Table 1. iii. c.12 , ii.m (Physical tests for insulation - Test for temperature index)	5000.0
Table 1. iii. c.13 , ii.n (Physical tests for insulation - Test for halogen acid gas evaluation)	5000.0
Table 1. iii. c.14 , ii.p (Physical tests for insulation - Test for smoke density rating)	5000.0
Table 1. iii. d.1 (Physical tests for sheath - Tensile strength and elongation at break)	1500.0
Table 1. iii. d.2 (Physical tests for Sheath - Loss of mass Test)	1500.0
Table 1. iii. d.3 (Physical tests for sheath - Ageing in air oven)	2000.0
Table 1. iii. d.4 (Physical tests for sheath - Shrinkage Test)	500.0
Table 1. iii. d.5 (Physical tests for sheath - Heat shock Test)	500.0
Table 1. iii. d.6 (Physical tests for sheath - Hot deformation Test)	500.0
Table 1. iii. d.7 (Physical tests for sheath - Thermal stability)	1000.0
Table 1. iii. d.8 (Physical tests for sheath - Oxygen Index Test)	5000.0
Table 1. iii. d.9 (Physical tests for sheath - Test for temperature Index)	5000.0
Table 1. iii. d.10 (Physical tests for sheath - Halogen acid gas evaluation)	5000.0
Table 1. iii. d.11 (Physical tests for sheath - Test for smoke density)	5000.0
Table 1. iii. e.1 (High Voltage Test (Water immersion Test))	3000.0
Table 1. iii. e.2 , ii.h (High voltage test or Spark test)	1500.0
Table 1.iii.e.3 , ii.g (Insulation resistance)	2000.0
Table 1. iii. e.4 (High voltage test (Cl. 10.2)(at room temperature))	1500.0
Table 1. iii. e.6 (Addition Ageing test (OU Cables only))	2000.0
- (Test on 2nd core)	2000.0
- (Test on 3rd core)	2000.0
- (Test on 4th core)	2000.0

1075

IS 6911 (2017) - Stainless steel plate, sheet and strip - Specification (Second Revision)

Stainless steel plate, sheet and strip - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Erichsen Cupping Test)	2000.0
10 (Hardness )	2000.0
10 (Elongation)	1000.0
10 (Yield Stress)	1000.0
10 (Tensile strength)	1000.0
Cl 7.1 & 7.2 of Table 1 (Carbon (as C), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Silicon (as Si), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Manganese (Mn), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Nickel (as Ni), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Chromium (as Cr), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Molybdenum (Mo), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Sulphur (as S), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Phosphorus (as P), Percent)	1000.0
Cl 7.1 & 7.2 of Table 1 (Other element)	1200.0
7.1 & 7.2 (Copper)	1200.0
7.1 & 7.2 (Aluminium)	1200.0
7.1 & 7.2 (Niobium)	1200.0
7.1 & 7.2 (Titanium)	1200.0

1076

IS 9974 : Part 1 (1981) - Specification for high pressure sodium vapour lamps: Part 1 general requirements and tests

Specification for high pressure sodium vapour lamps: Part 1 general requirements and tests

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Lamp Dimensions )	5000.0
5 (Marking)	5000.0
6 (Lamp Caps )	5000.0
7.2 (Lamp Starting & Warm-up Test )	5000.0
7.3 (Electrical characteristics)	10000.0
7.4 (Lamp Photometric characteristics)	15000.0

1077

IS 15885 : Part 2 : Sec 13 (2012) - Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Marking)	1200.0
8 (Protection against accidental contact with live parts )	1200.0
9 (Terminals)	1200.0
10 (Provisions for protective earthing )	1200.0
11 (Moisture resistance & Insulation Resistance)	3500.0
12 (Electric strength)	1500.0
13 (Thermal endurance test for windings of ballasts )	5500.0
14 (Fault conditions)	2000.0
15 (Transformer heating)	2000.0
16 (Construction )	1200.0
17 (Creepage distances and clearances )	1200.0
18 (Screws, current-carrying parts and connections )	1200.0
19 (Resistance to Heat)	2000.0
19 (Resistance to Fire)	5000.0
19 (Resistance to Tracking)	5000.0
20 (Resistance to corrosion)	2000.0

1078

IS 16104 (2012) - D.C. or A.C. supplied electronic control gear for led modules - Performance requirements

D.C. or A.C. supplied electronic control gear for led modules - Performance requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Marking )	1200.0
7 (Output Voltage and Current)	1200.0
8 (Total Circuit Power)	2000.0
9 (Circuit Power Factor)	1200.0
10 (Supply Current)	1200.0
12 (Operational Test for abnormal condition)	5000.0
13 (Temperature Cyclic Test)	10000.0
13 (Supply voltage Switching Test (upto 200 cycle) )	5000.0
13 (Accelerated Operational Life Test upto 200 hrs.)	5000.0

1079

IS 16103 : Part 2 (2012) - Led modules for general lighting: Part 2 performance requirements

Led modules for general lighting: Part 2 performance requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Marking)	1200.0
5 (Dimension)	1200.0
7 (Power measurement)	2000.0
8.1 (Luminous flux)	5000.0
8.2 (Luminous intensity)	5000.0
8.3 (Module efficacy)	2000.0
9.1 (Chromaticity coordinates)	1000.0
9.1 (corelated colour temperature )	2000.0
9.2 (Colour rendering index (CRI) )	2000.0
10.2 (Lumen maintenance)	30000.0
10.3 (Temperature Cyclic Test)	10000.0
10.3 (Supply voltage Switching Test )	10000.0

1080

IS 16103 : Part 1 (2012) - Led modules for general lighting: Part 1 safety requirements

Led modules for general lighting: Part 1 safety requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Marking)	1200.0
8 (Terminals)	1200.0
9 (Provisions for protective earthing)	1200.0
10 (Protection against accidental contact with live parts )	1200.0
11 (Moisture resistance)	2000.0
11 (Insulation Resistance)	1500.0
12 (High Voltage Test)	1500.0
13 (Fault conditions)	2000.0
14 (Conformity testing during manufacture)	5000.0
15 (Construction)	1200.0
16 (Creepage distances )	600.0
16 (clearances )	600.0
17 (Screws, current-carrying parts and connections)	1200.0
18 (Ball Pressure Test)	2000.0
18 (Glow Wire Test)	5000.0
18 (Tracking Index Test)	5000.0
19 (Resistance to Corrosion)	5000.0
21 (Heat Management)	2000.0