NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb@nic.in

Scope List

Reset

1161 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

1021

IS 10322 : Part 5 : Sec 1 (2012) - Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Marking )	1200.0
7 (Construction)	1200.0
8 (Creepage Distances & Clearances)	1200.0
9 (Provision for earthing)	1200.0
10 (Terminals)	1200.0
11 (External & Internal wiring)	1200.0
12 (Protection against Electric Shock)	1200.0
13 (Endurance Test & Thermal Tests)	5500.0
14 (Resistance to Dust )	6000.0
14 (Resistance to Moisture)	6000.0
15 (Insulation Resistance )	2000.0
15 ( Electric Strength)	3000.0
18 (Resistance to heat )	2000.0
18 (Resistance to fire )	5000.0
18 (Resistance to tracking )	5000.0
17 (Photometric Tests)	10000.0

1022

IS 10322 : Part 1 (2014) - Luminaires: Part 1 general requirements and tests (First Revision)

Luminaires: Part 1 general requirements and tests (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Marking )	1200.0
4 (Construction)	1200.0
5 (External & Internal Wiring)	1200.0
7 (Provision for Earthing)	1200.0
8 (Protection against Electric Shock)	1200.0
9 (Ingress Protection 1st Characterictics)	6000.0
9 (Ingress Protection 2nd Characterictics)	6000.0
10 (Insulation Resistance)	2000.0
10 ( electric strength )	3000.0
11 (Creepage Distance )	600.0
11 (Clearance)	600.0
12 (Endurance Test and Thermal Test)	5500.0
13 (Resistance to heat )	2000.0
13 (Resistance to fire )	5000.0
13 (Resistance to tracking )	5000.0
14 (Screw Terminals)	1200.0
15 (Screwless Terminals & Electrical connections)	1200.0

1023

IS 2339 (2013) - Aluminium paints for general purposes - Specification (First Revision)

Aluminium paints for general purposes - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Compostion)	200.0
5.1.1 (Leafing Value)	1500.0
5.3 i (Drying Time Hard dry)	200.0
5.3 ii (Consistency)	200.0
5.3 iii (Finish)	200.0
5.3 iv (Mass)	200.0
5.3 v (Wet Opacity)	500.0
5.3 vi (Flexibility and adhesion, bend test usingType 1 apparatus and 6.25 mm dia Mandrel)	200.0
5.3 vii (Resistance to humidity under condition of condensation)	3000.0
5.3viii (Flash point)	2000.0
5.3 ix (Keeping properties)	5000.0
5.2 (Lead Restriction)	500.0

1024

IS 15489 (2013) - Paint, plastic emulsion - Specification (First Revision)

Paint, plastic emulsion - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.12 (Toxic metals such as lead, cadmium, chromium (VI))	3600.0
6.12 (Volatile organic compounds,)	2000.0
6.1 (Keeping properties)	5000.0
6.5 (Mass in kg/10 litre (IS 101 (Part 1/Sec 7)))	500.0
6.11 (Recoating properties, (Annexure J of IS 15489:2013))	2000.0
6.11 (Washability and cleanability (Annexure G of IS 15489:2013))	1900.0
6.11 (Resistance to alkali (Annexure F of IS 15489:2013))	500.0
6.11 (Accelerated storage stability test (Annexure H of IS 15489:2013))	700.0
6.11 (Colour (Annexure E of IS 15489:2013))	100.0
6.11 (Gloss at 60 degree d) Class D, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree c) Class C, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree b) Class B, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree a) Class A (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Finish (Annexure D of IS 15489:2013))	1200.0
6.11 (Consistency (Annexure B of IS 15489:2013))	1200.0
6.11 (Drying time a) Hard dry (Class C and D) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Hard dry (Class A and B) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Surface dry (Class C and D) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Surface dry (Class A and B))	1000.0
6.9 (Lead Restriction)	1000.0
6.8 (Durability Test for Exterior Use Only Accelerated weathering apparatus QUV ( for 21 days))	15200.0
6.7 & 6.11 (Fastness to Light (Xenon Arc apparatus for 500 hrs) (IS 101 Part 4/ Sec 3))	15000.0
6.6 (Opacity (IS 101 ( Part 1/Sec 3)))	1000.0
6.2 (Conditions in the Container)	200.0
6.3 (Thinning)	1000.0
6.4 (Application Properties)	700.0
6.1 (Composition)	200.0

1025

IS 10322 : Part 5 : Sec 5 (2013) - Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Marking )	1200.0
6 (Construction)	1200.0
6 (Creepage Distances )	600.0
6 (Clearances)	600.0
6 (Provision for earthing)	1200.0
6 (Terminals)	1200.0
6 (External & Internal wiring)	1200.0
6 (Protection against Electric Shock)	1200.0
6 (Endurance Test & Thermal Tests)	5500.0
6 (Resistance to Dust)	6000.0
6 (Resistance to Moisture)	6000.0
6 (Insulation Resistance )	2000.0
6 ( Electric Strength)	3000.0
6 (Resistance to heat )	2000.0
6 (Resistance to fire )	5000.0
6 (Resistance to tracking )	5000.0
6 (Photometric Tests)	10000.0

1026

IS 16102 : Part 2 (2017) - Self - Ballasted led lamps for general lighting services: Part 2 performance requirements (First Revision)

Self - Ballasted led lamps for general lighting services: Part 2 performance requirements (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Marking)	1200.0
6 (Dimension)	1200.0
8 (Power )	2000.0
9 (Luminous Flux)	5000.0
10 (Centre Beam intensity)	3000.0
11 (Beam angle)	3000.0
12 (Chromaticity Co-ordinates & Colour rendering index)	5000.0
13 (Lumen Maintenance)	85000.0
15 (Harmonics & PF)	2000.0

1027

IS 2074 (2015) - Ready Mixed Paint, Air Drying, Red Oxide - Zinc Chrome, Priming - Specification

Ready Mixed Paint, Air Drying, Red Oxide - Zinc Chrome, Priming - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.6, xii (Keeping properties)	5000.0
5.6,xi (Accelerated storage stability test)	200.0
5.6,x.c (Resistance to salt spray)	500.0
5.6,x.b (Resistance to sea water (applicable for marine paints only))	50.0
5.6,x.a (Resistance to humidity)	2500.0
5.6,ix (Volume solids)	200.0
5.6,viii (Flash point)	500.0
5.6,vii.b (Flexibility and adhesion: Scratch hardness (load 1000g))	100.0
5.6,vii.a (Flexibility and adhesion:Bend test (with 6.25 mm dia mandrel and in type 1 apparatus))	100.0
5.6,vi (Colour)	50.0
5.6,v (Fineness of grind, microns)	100.0
5.6,iv.a (Finish)	100.0
5.6,iii.b (Drying: hard dry)	100.0
5.6,iii.a (Drying: Surface dry)	100.0
5.6,ii (Mass, kg/10litre)	200.0
5.6,i. b (Viscosity by Ford cup No. 4 at 27 ± 2°C)	200.0
5.6,i. a (Consistency)	200.0
5.5 (Lead Restriction)	200.0
5.3 (Compatibility with thinner)	200.0
5.1.2 (Volatile vehicle)	200.0
5.1.1.b (Synthetic red oxides of iron red oxide (as Fe2O3))	1000.0
5.1.1.a (zinc oxide)	500.0
5.1.1.a (chromic anhydride)	1000.0
5.1.1.a (Zinc chrome)	500.0
5.1.b (Driers)	50.0
5.1.a (Pigment, percent by mass)	1200.0

1028

IS 6394 (2006) - Ultrasonic testing of seamless metallic tubular products by contact and immersion methods - Code of practice (Second Revision)

Ultrasonic testing of seamless metallic tubular products by contact and immersion methods - Code of practice (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 6394 (Ultrasonic examination)	2000.0

1029

IS 5523 (1983) - Methods of testing anodic coatings on aluminium and its alloys (First Revision)

Methods of testing anodic coatings on aluminium and its alloys (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 5523 (Coating thickness)	2000.0

1030

IS 2831 (2012) - Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Dimensions)	1000.0
10.1.b (Sulphur print)	3500.0
10.1.a (Macro test)	1000.0
6 (Phosphorus)	500.0
6 (Sulphur)	500.0
6 (Manganese)	500.0
6 (Silicon)	500.0
6 (Carbon)	500.0

1031

IS 2830 (2012) - Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Dimensions)	1000.0
10.3 (Camber)	500.0
10.2 (Bend)	500.0
10.1(b) (Sulphur print test)	3500.0
10.1(a) (Macro Examination)	1000.0
6 (Phosphorus)	500.0
6 (Sulphur)	500.0
6 (Manganese)	500.0
6 (Copper)	500.0
6 (Carbon)	500.0

1032

IS 1285 (2023) - Wrought Aluminium and Aluminium Alloys — Extruded Round Tube and Hollow Sections for General Engineering Purposes

Wrought Aluminium and Aluminium Alloys — Extruded Round Tube and Hollow Sections for General Engineering Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10 (Tensile Strength (as per IS 733))	1000.0
8 (Dimension)	1000.0
10 (% Elongation (as per IS 733))	1000.0
10 (0.2 % Proof Stress (as per IS 733))	1000.0
6 (Freedom from Defect)	1000.0
8 (Copper, % by mass)	600.0
8 (Magnesium, % by mass)	600.0
8 (Silicon, % by mass)	600.0
8 (Iron, % by mass)	600.0
8 (Manganese, % by mass)	600.0
8 (Zinc, % by mass)	600.0
8 (Titanium, % by mass)	600.0
8 (Chromium, % by mass)	600.0
8 (Others, % by mass)	600.0
6 (Freedom from Defect)	1000.0

1033

ASM Vol.11 (2002) - Metallographic examination-Failure investigation ( minimum)

Metallographic examination-Failure investigation ( minimum)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASM (Failure Analysis)	25000.0

1034

IS 1608 : Part 1 (2018) - Metallic materials - Tensile testing: Part 1 method of test at room temperature (Fourth Revision)

Metallic materials - Tensile testing: Part 1 method of test at room temperature (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
14 (Tensile Test with sample preparation)	4000.0
14 (Tensile Test without sample preparation)	3000.0

1035

IS 1586 : Part 1 (2025) - Metallic Materials - Rockwell Hardness Test - Part 1 Test Method

Metallic Materials - Rockwell Hardness Test - Part 1 Test Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Hardness)	2000.0

1036

IS 1500 : Part 1 (2019) - Metallic materials - Brinell hardness test: Part 1 test method (Fifth Revision)

Metallic materials - Brinell hardness test: Part 1 test method (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Hardness)	2000.0

1037

IS 4270 (2001) - Steel tubes used for water wells specification (Third Revision)

Steel tubes used for water wells specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Outside diameter)	3000.0
7 (Weight in kg/m)	1000.0
6.2 (Flattening)	1000.0
6.1 (% Elongation)	1000.0
6.1 (Yield Strength)	1000.0
6.1 (Tensile Strength)	1000.0

1038

IS 4923 (2017) - Hollow steel sections for structural use - Specification (Third Revision)

Hollow steel sections for structural use - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.2 (Elongation, %)	1000.0
15.2 (Yield Strength, MPa)	1000.0
15.2 (Tensile Strength, MPa)	1000.0
9.1 (Dimension, mm)	1000.0
9.1 (Weight, kg/m)	1000.0
7.1 (Sulphur, % by mass)	500.0
7.1 (Phosphorus, % by mass)	500.0

1039

IS 1501 (2002) - Method For Vickers Hardness Test for Metallic Materials

Method For Vickers Hardness Test for Metallic Materials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 1501 (Case depth)	4000.0
IS 1501 (Hardness)	1000.0

1040

IS 513 : Part 1 (2016) - Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Yield stress)	1000.0
8.2 (Cupping Test)	3000.0
8.3 (Hardness Test)	2000.0
11 (Thickness)	1000.0
8.1 (Tensile strength)	1000.0
8.1 (% Elongation)	1000.0
8.4 (Bend Test)	1000.0
7 (Chemical composition (Carbon))	625.0
7 (Chemical composition (Manganese))	625.0
7 (Chemical composition (Sulphur))	625.0
7 (Chemical composition (Phosphorus))	625.0

1041

IS 6003 (2010) - Indented Wire For--Prestressed Concrete â€”

Indented Wire For--Prestressed Concrete â€”

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.4 (Elongation)	1000.0
7.2 (Proof Stress)	1000.0
7.1 (Tensile strength)	3000.0
6.1.2 (Mass)	1500.0
5.1 (Diameter)	1000.0
7.3 (Reverse Bend Test)	2000.0
7.2 (Proof Stress)	1000.0

1042

IS 3203 (1982) - Methods of testing local thickness of electroplated coatings (First Revision)

Methods of testing local thickness of electroplated coatings (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 3203 (Coating thickness)	2000.0

1043

ASME ASME (2021) - Performance test ( Plate & electrodes not supplied by NTH)

Performance test ( Plate & electrodes not supplied by NTH)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASME (Welding procedure qualification)	11000.0
ASME (Welder qualification)	5000.0

1044

ASME ASME Section IX (2021) - Preparation of welding procedure specification (WPS) as per ASME Section IX

Preparation of welding procedure specification (WPS) as per ASME Section IX

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASME Section IX (Welding procedure Specification)	10000.0

1045

ASME Section IX (2019) - 2019 Boiler and Pressure Vessel Code

2019 Boiler and Pressure Vessel Code

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
QW 191 (Radiography Test -Pipe)	3200.0
QW 191 (Radiography Test -Plate)	1200.0

1046

IS 16102 : Part 1 (2012) - Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Marking )	1200.0
6 (Interchangeability)	1200.0
7 (Protection against electric shock)	1200.0
8 (Insulation resistance )	2000.0
8 (Electric strength after humidity treatment)	3000.0
9 (Mechanical strength)	1200.0
10 (Cap temperature rise)	2000.0
11 (Resistance to heat)	2000.0
12 (Resistance to ignition)	5000.0
12 (Crepage distance)	600.0
14 ( clearances)	600.0

1047

IS 1182 (1983) - Recommended - Practice for radiographic examination of fusion welded butt joints in steel plates (Second Revision)

Recommended - Practice for radiographic examination of fusion welded butt joints in steel plates (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 9.1 (Preparation of Weld assembly for Radiography test)	4000.0

1048

IS 16106 (2012) - Method of electrical and photometric measurements of solid state lighting (Led) products

Method of electrical and photometric measurements of solid state lighting (Led) products

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Input Voltage)	1000.0
9 (Current)	1000.0
9 (Power)	1000.0
9 (Power Factor)	1000.0
11 (Luminous Flux)	5000.0
NA (Luminous Intensity & Beam Angle)	5000.0
NA (Luminious Intensity Distribution)	5000.0
NA (Cromaticity Coordinates)	2000.0
NA (Correlated Color Temperature)	5000.0
NA (colour rendering Index)	5000.0
NA (CIE 1931 Colour Diagram)	2000.0
NA (Spectral Power Distribution)	2000.0
Annex I (Illumination Data at different distance as per test method IS 16106:2012)	3000.0
Annex : II (IES File for Lighting parameters)	3000.0
NA (Luminous Efficacy)	5000.0

1049

IBR 1950 (2023) - Qualified Boiler Welder's Certificate

Qualified Boiler Welder's Certificate

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Chapter XIII (Certification of welder per position of welding on Plate (SMAW/FCAW) (Plate and Electrodes not supplied by NTH))	3000.0
Chapter XIII (Certification of welder on Pipe & Branch Pipe by TIG/GTAW)	9000.0
Chapter XIII (Certification of welder per position of welding on Pipe/Tube by MMAW)	4500.0
Chapter XIII (Certification of welder per position of welding on Pipe by TIG/GTAW)	4500.0
Chapter XIII (Certification of welder per position of welding on Tube by TIG/GTAW)	4500.0

1050

IS 7666 (1988) - Ultrasonic examination of ferritic castings of carbon and low alloy steel - Recommedned procedure (First Revision)

Ultrasonic examination of ferritic castings of carbon and low alloy steel - Recommedned procedure (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 7666 (Ultrasonic examination)	2000.0