NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1274 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

811

F-9 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-9 Technical Name :Inoranic zinc silicate coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-9 Technical Name :Inoranic zinc silicate coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max)	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Pot life at 30⁰C for two component paints, hrs)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Temperature resistance 400 ⁰ C (ASTM D 2485 method B))	1000.0
11 (Temperature resistance 400 ⁰ C Dry Service (ASTM D 2485 method B))	2000.0
12 (Zinc Content as Zn in dry film % by mass)	1200.0
13 (MEK rub test ASTM D 4752)	1200.0
14 (Non Volatile Matter (% by mass) Component-A Zinc dust)	1000.0
15 (Non Volatile Matter (% by mass) Component-B liquid accelerator)	1000.0
16 (Volatile Matter (% by mass) Component-A Zinc dust)	1200.0
17 (Volatile Matter (% by mass) Component-B liquid accelerator)	1200.0
18 (Specific Gravity Component-A Zinc dust (ASTM D1475))	1200.0
19 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
20 (Ash Content (% by mass)Component-A Zinc dust)	1200.0
21 (Ash Content (% by mass)Component-B Liquid Accelerator)	1200.0

812

F-8 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-8 Technical Name: Self priming surface tolerant high build epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-8 Technical Name: Self priming surface tolerant high build epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Pot life at 30⁰C for two component paints, hrs)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Temperature resistance 80 ⁰ C (ASTM D 2485 method A))	1000.0
11 (Temperature resistance 80 ⁰ C (ASTM D 2485 method B))	2000.0
12 (Full cure at 30 Deg C (for immersion / high temperature service))	1200.0
13 (Non Volatile Matter (% by mass) Component-A (Base))	1000.0
14 (Non Volatile Matter (% by mass) Component-B (Hardener))	1000.0
15 (Volatile Matter (% by mass) Component-A (Base))	1200.0
16 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
17 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
18 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
19 (Ash Content (% by mass)Component-A (Base))	1200.0
20 (Ash Content (% by mass)Component-B)	1200.0

813

Customised specification for Cumin Powder - Customised specification for Cumin Powder

Customised specification for Cumin Powder

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Description)	500.0
2 (Moisture, Percent by mass)	500.0
3 (Total ash ,Dry basis ,Percent by mass)	500.0
4 (Acid insoluble ash on dry basis, Percent by mass)	500.0
5 (Volatile oil on dry basis, Percent by mass)	500.0
6 (Non Volatile ether extract , Percent by mass)	500.0
7 (Salmonella (in 25 g))	500.0

814

F-7 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-7 Technical Name High build coal tar epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-7 Technical Name High build coal tar epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Pot life at 30⁰C for two component paints, hrs)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Temperature resistance 80 ⁰ C (ASTM D 2485 method A))	1200.0
11 (Temperature resistance 80 ⁰ C (ASTM D 2485 method B))	1200.0
12 (Full cure at 30 Deg C (for immersion / high temperature service))	1200.0
13 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
14 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
15 (Volatile Matter (% by mass) Component-A (Base))	1200.0
16 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
17 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
18 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
19 (Ash Content (% by mass)Component-A (Base))	1200.0
20 (Ash Content (% by mass)Component-B)	1200.0

815

Customised Specification Organic Manure (On the lines of FCO-1985) - Customised Specification Organic Manure (On the lines of FCO-1985)

Customised Specification Organic Manure (On the lines of FCO-1985)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Moisture, Percent by weight)	1000.0
3 (Bulk density (g/cm Sq.))	1000.0
4 (Total Organic matter (percent by weight))	1000.0
5 (Total Organic carbon (percent by weight))	1000.0
6 (Total Nitrogen (as N), percent by weight)	1000.0
7 (Total Phosphates (As P2O5), Percent by weight)	1000.0
8 (Total potassium (as K2O), percent by weight)	1000.0
9 (Calcium (as Ca), mg/kg)	1000.0
10 (Magnesium (as Mg), mg/Kg)	1000.0
11 (Iron (as Fe), mg/Kg)	1000.0
12 (Zinc (as Zn), mg/Kg)	1000.0
2 (pH (dilution at 10%))	1000.0

816

F-6 C EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-6 C Technical Name : Solventless epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-6 C Technical Name : Solventless epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Potlife at 30 deg C for 2 component paints, hours)	1200.0
9 (Full cure at 30oC (for immersion/ high temperature service))	1200.0
10 (Adhesion ASTM D 4541 (Mpa))	2000.0
11 (Temperature resistance (ASTM D 2485 Methods A))	1200.0
12 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
13 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
14 (Volatile Matter (% by mass) Component-A (Base))	1200.0
15 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
16 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
17 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
18 (Ash Content (% by mass)Component-A (Base))	1200.0
19 (Ash Content (% by mass)Component-B)	1200.0

817

F-6B EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-6B Technical Name :Epoxy high build coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-6B Technical Name :Epoxy high build coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	1000.0
2 (DFT per coat, microns)	1000.0
3 (Theoretical covering capacity in m sq/coat/litre)	1000.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Potlife at 30 deg C for 2 component paints, hours)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
11 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
12 (Volatile Matter (% by mass) Component-A (Base))	1200.0
13 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
15 (Ash Content (% by mass)Component-A (Base))	1200.0
16 (Ash Content (% by mass)Component-B)	1200.0
17 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
18 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
19 (Temperature resistance 80 ⁰ C (ASTM D 2485 method A))	1000.0
1.1 (Colour as per Manufacturer’s supply shade’)	100.0

818

F-6A EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-6A Technical Name :Epoxy high build coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-6A Technical Name :Epoxy high build coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	1000.0
2 (DFT per coat, μ)	1000.0
3 (Theoretical covering capacity in m2/coat/ litre)	1000.0
4 (Weight per litre in Kg/litre)	1000.0
5 (Touch dry at 30DegC (max.))	1000.0
6 (Hard dry at 30Deg.C (max.))	1000.0
7 (Full cure at 30 deg.C (for immersion/ high temperature service))	1000.0
8 (Over-coating interval, hrs)	1000.0
9 (Pot life at for two component paints, hrs)	1000.0
10 (Adhesion (ASTM D 4541))	2000.0
11 (Temperature resistance 80 deg.C for 24 hrs (ASTM D 2485 Method A))	2000.0
12 (Non Volatile Matter (% by mass) Component-A (Base))	1000.0
13 (Non Volatile Matter (% by mass) Component-B (Hardener))	1000.0
14 (Volatile Matter (% by mass) Component-A (Base))	1000.0
15 (Volatile Matter (% by mass) Component-B (Hardener))	1000.0
16 (Specific Gravity Component-A (Base) (ASTM D1475))	1000.0
17 (Specific Gravity Component-B curing agent(ASTM D1475))	1000.0
18 (Ash Content (% by mass)Component-A (Base))	1000.0
19 (Ash Content (% by mass)Component-B)	1000.0

819

F-2 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-2 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name : Aliphatic PU finish paint

F-2 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name : Aliphatic PU finish paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	1000.0
2 (DFT per coat, microns)	1000.0
3 (Theoretical covering capacity in m sq/coat/litre)	1000.0
4 (Weight per liter in kg/litre)	1000.0
5 (Touch dry at 30 Deg c)	500.0
6 (Hard dry at 30 deg C max)	500.0
7 (Over coating interval , hours)	1000.0
8 (Potlife at 30 deg C for 2 component paints, hours)	1000.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Abrasion Resistance, mg per 1000gm/CS17/1000cycle (ASTM D4060))	2000.0
11 (Temperature resistance 80⁰ C (ASTM D 2485 Method A))	2000.0
12 (Non Volatile Matter, % By mass Component-A (Base))	1000.0
13 (Non Volatile Matter, % By mass Component-B (Hardener))	1000.0
14 (Volatile Matter, % By mass Component-A (Base))	1000.0
15 (Volatile Matter, % By mass Component-B (Hardener))	1000.0
16 (Specific gravity of base (ASTM D1475))	1000.0
17 (Specific gravity of Curing agent (ASTM D1475))	1000.0
18 (Ash Content, % By mass Component-A (Base))	1000.0
19 (Ash Content, % By mass Component-B (Hardener))	1000.0

820

P-6 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - P-6 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name :Epoxy zinc phosphate primer

P-6 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name :Epoxy zinc phosphate primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	2000.0
2 (DFT per coat microns)	100.0
3 (Theoretical covering capacity in m sq/coat/litre)	1000.0
4 (Touch dry at 30 Deg c max (hours))	1000.0
5 (Hard dry at 30 deg C max(hours))	1000.0
6 (Over coating interval , hours)	1000.0
7 (Potlife at 30 deg C for 2 comp paints, hours)	1000.0
8 (Adhesion ASTM D 4541 (Mpa))	5000.0
9 (Temperature resistance min deg C 80 METHOD A ASTM D2485)	3000.0
10 (Non Volatile Matter % By mass Component-A (Base))	1000.0
11 (Non Volatile Matter % By mass Component-B (Hardener))	1000.0
12 (Volatile Matter % By mass Component-A (Base))	500.0
13 (Volatile Matter % By mass Component-B (Hardener))	500.0
14 (Specific Gravity Component-A (Base))	500.0
15 (Specific Gravity Component-B (Hardener))	500.0
16 (Ash content Component-A (Base))	1000.0
17 (Ash Content % By mass Component-B (Hardener))	1000.0
10 (weight per litre in kg/litre)	500.0
11 (Abrasion Resistance(ASTM D4060)1000gm load/1000Cycles CS17 wheel or CS 10 wheel)	2000.0

821

NTH ER PAINT LAB CUSTOMER SPECIFICATION (2012) - PAINT ,RFU,FINISHING,MATT AIR DRYING BRUSHING /SPRAYING

PAINT ,RFU,FINISHING,MATT AIR DRYING BRUSHING /SPRAYING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Film strength at impact Impact Resistance Test (ASTM D 2794))	2000.0
2 (Hardness test: Pencil Hardness test IS:101(part 5/Sec1)1988 (Reaffirmed2019).)	1000.0
3 (Scratch Hardness test (1500 g weight) for pencil hardness up to 2H IS 101 Part 5 sec 2 RA 2019)	1000.0
4 (Drying Time a) Surface Dry IS 101 (Part 3/sec 1), 1986)	1000.0
5 (Drying Time b) Hard Dry &tack free IS 101 (Part 3/sec 1), 1986)	1000.0
6 (Specular Gloss at 60 º IS 101 (Part 4/Sec 4))	1000.0
7 (Finish IS 101 part 3 sec 4,1987)	1000.0
8 (Fineness of Grind ,in microns IS 101 part 3 section 5)	1000.0
9 (Mass in kg/10 ltrs IS 101 part 1 sec 7)	1000.0
10 (Accelerated Weathering Test QUV –UVA lamp 340 nm For10 days(at Basic Climate Condition) MIL Std -810-G)	20000.0
11 (Resistance to Petrol -Benzene Mixture Immersion test jSS-8010-82:2012,Appendix -D.)	2000.0
12 (Resistance to Warm water jSS-8010-82:2012,Appendix-E)	1000.0
13 (Accelerated Storage Stability Duration 96 hours at 60 Deg .C jSS-8010-82:2012,Appendix -C.)	2000.0
14 (Resistance to salt Water:- 7 Cycles JSS-8010-82:2012,Appendix -F. Test Condition (one Cycle):-One Hour immersion in salt water Three Hours outside exposure at angle of 45 Deg Facing south then one hour refrigeration at 4 plus minus 2 Deg C then again exposued angle of 45 Deg Facing south till next cycle)	3500.0
15 (Resistance to Lubricating oil (immersion test for 2 hours at 50 Deg c jSS-8010-82:2012,Appendix -A.)	1000.0
16 (Resistant to heat (at 150 deg c for 2 hours) JSS-8010-82:2012,Appendix-B)	1000.0
17 (Resistance to low temperature for 120 hours at-20 deg c (+/- 0.1 deg c ))	5000.0
18 (Accelerated weathering Test Xenon Radiation For 30days as per moderate climatic conditions. MIL STD -810-G.)	40000.0
6 (ANTI GRAFFITI PROPERTIES ASTM D 6578)	5000.0
1.2 (COVERING STRENGTH covering strength must be tested on a Garmsen clear glass plate with a minimum dry film thickness applied according to WN 11500 over a black and white contrast card. There may be no visible contrast between the black and white backgrounds.)	2500.0

822

13209 (2024) - Indelible Ink-Specification

Indelible Ink-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Description)	1000.0
3.3 (Colour)	1000.0
3.4 (pH)	1000.0
3.5 (Total solids)	1000.0
3.6 (Development)	1000.0
3.7.1 (Performance- Resistance to Bleaching)	1000.0
3.7.2 (Performance- Resistance to organic solvents)	1000.0

823

IS 12894:2002 (On the lines, comparative tests for Fly ash bricks) (2002) - Pulverized Fuel ash lime bricks-Specification

Pulverized Fuel ash lime bricks-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Comparative tests for fly ash bricks (on the lines of IS 12894:2002))	14000.0

824

IS 15658:2021-(on the lines,Comparative Tests for Paver blocks) (2021) - Concrete Paving Blocks-Specification

Concrete Paving Blocks-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1. (Comparative tests as per IS 15658:2021)	32000.0

825

Custom - Testing of Gold Plated Silver Medal

Testing of Gold Plated Silver Medal

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Silver, Percent by mass)	2000.0
2 (Gold (Qualitative))	1000.0
3 (Thickness of Gold plating on silver medal.)	2000.0
0 (Weight (gm))	1000.0

826

7532 (2018) - Soft Soap — Specification

Soft Soap — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Description)	1200.0
5.3 (Consistency)	1200.0
i) (Total fatty matter, percent by mass)	1200.0
ii) (Unsaponified and unsaponifiable matter, percent by mass)	1200.0
iii) (Rosin acids, percent by mass of total fatty matter)	1200.0
iv) (Total free alkali (as K2O), percent by mass)	1200.0
v) (Free caustic alkali (as K2O), percent by mass)	1200.0

827

IRS-T-46 (1996) - Indian Railway Standard Specification for Spheroidal Graphite Cast Iron Inserts

Indian Railway Standard Specification for Spheroidal Graphite Cast Iron Inserts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

828

NTHER- Calibration of Voltage and Current Source (V/I) Method) - Calibration of Voltage and Current Source (V/I) Method

Calibration of Voltage and Current Source (V/I) Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Current Voltage)	1500.0
A.2 (Current Voltage)	2000.0

829

NTHER- Calibration of High Current Source (V/I Method) - Calibration of High Current Source (V/I Method)

Calibration of High Current Source (V/I Method)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Current)	1500.0
A.2 (Current)	2000.0
A.3 (Current)	3000.0
A.4 (Current)	4000.0

830

NTHER- Calibration of LCR Meter - Calibration of LCR Meter

Calibration of LCR Meter

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Inductance, Capacitance, Resistance)	2000.0

831

NTHER- Calibration of Signal / Function Generator - Calibration of Signal / Function Generator

Calibration of Signal / Function Generator

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Frequency)	2000.0
A.2 (Frequency)	3000.0
A.3 (Frequency)	4000.0
A.4 (Frequency)	4500.0
A.5 (Frequency)	5000.0

832

DGMS Circular(Approval) No 04 of 2013 (2013) - Revised standards for testing and use of Resin capsules as grouting ,material for Roof bolting purposes in the below ground workings of coal mines

Revised standards for testing and use of Resin capsules as grouting ,material for Roof bolting purposes in the below ground workings of coal mines

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.0.B. (Test for Compressive strength-after 30 minutes (Average compressive strength))	7500.0
2.0.B. (Test for Compressive strength-24 hrs (Average compressive strength))	7500.0
2.0.B. (Test for Bond strength Test-30 minutes (Average bond strength in Tonnes))	7500.0
2.0.A. (Test for Gel time & Setting time- For Fast set type (Average Gel time & Setting Time in seconds))	2500.0
2.0.A. (Test for Gel time & Setting time- for Slow set type (Average Gel time & Setting Time in seconds))	2500.0
2.0.A. (Test for Reaction Temperature ( deg C) (for slow setting))	1250.0
2.0.A. (Test for Thermal stability-Gel time & setting time in seconds-Fast set Type (after conditioning @ 5 deg C for 1 hr followed by 45 deg C for 1 hr))	1250.0
2.0.A. (Test for Thermal stability-Gel time & setting time in seconds-Slow set Type (after conditioning @ 5 deg C for 1 hr followed by 45 deg C for 1 hr))	1250.0
2.0.B (Test for Shear strength:(in MPa))	5000.0
2.0.B. (Test for shrinkage (only for slow type))	-
2.0.B. (Test for Flammability)	5000.0
2.0.A (Test for Reaction Temperature ( deg C) (for Fast setting))	1250.0

833

IS 17050 (2023) - Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK Code)

Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK Code)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Test to verify the protection against mechanical impact)	10000.0

834

Custom Paper Core(ER)-2022 (2022) - Paper Core

Paper Core

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions)	2000.0
2.0 (Thickness)	2000.0
3.0 (Compression Strength)	2000.0

835

PCEE/NR/121-Elect/PS/2019(Rev-4) dated 04.11.2019 (2019) - LED Based Luminaries ( Input Voltage Single Phase 230 Volt AC, 50 Hz) for General Service Application.

LED Based Luminaries ( Input Voltage Single Phase 230 Volt AC, 50 Hz) for General Service Application.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1.13 (Insulation Resistance between earth and Current Carrying Parts shorted together at 500V megger & after HV Test)	2000.0
4.13 (Shall be tested at 1500 Volt AC for One Minutes between supply terminals & body of the unit.)	3000.0
3.3.8( rev. 3) (Internal Voltage Surge Protection)	1500.0
3.1.7 (Photometric Test ,as per Specification No. CEE/NR/121-Elect/PS/2018( Rev -3) dated 28.06.2018 & LM79)	18000.0

836

C/QA&I/SFQP/SCW, Rev.4 dated 29.01.2016 (2016) - Measurement of Resistivity of Gravel20/40mm

Measurement of Resistivity of Gravel20/40mm

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Measurement of Resistivity of Gravel)	20000.0

837

IS 101 (2015) - Determination of Volatile Organic Compound (VOC) Content gram per litre— Difference Method

Determination of Volatile Organic Compound (VOC) Content gram per litre— Difference Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3 (Volatile Organic Compound (VOC) Content gram per liter (on the lines of IS 101part2/Sec-1):1988 & IS 101 Part 2/Sec2):1986)	4000.0

838

RDSO MP-0.41.00.01 : Part Rev 1 (2003) - Schedule of Technical Requirements for Transition Screw Couplings for Centre Buffer Coupler

Schedule of Technical Requirements for Transition Screw Couplings for Centre Buffer Coupler

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3.3 (Destruction Test)	7500.0
7.3.2 (Impact Test)	7500.0

839

IS 104 (2017) - Ready Mixed Paint, Brushing, Zinc Chrome, Priming

Ready Mixed Paint, Brushing, Zinc Chrome, Priming

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
i) Table 1 Cl 4.3&7.1 (Consistency)	100.0
ii) Table 1 Cl 4.3&7.1 (Finish)	100.0
iii) Table 1 Cl 4.3&7.1 (Drying time-Hard dry in hours)	100.0
iv) Table 1 Cl 4.3&7.1 (Mass, kg/10 liter)	100.0
v) Table 1 Cl 4.3&7.1 (colour)	100.0
vi) Table 1 Cl 4.3&7.1 (Wet opacity, m2/10 liter)	100.0
vii.a) Table 1 Cl 4.3&7.1 (Flexibility and adhesion a. Scratch hardness (Load 1 000 g))	100.0
vii.b) Table 1 Cl 4.3&7.1 (Flexibility and adhesion b) Bend test, with 6.25 mm dia mandrel and type 1 apparatus)	100.0
viii) Table 1 Cl 4.3&7.1 (Flash point)	200.0
ix.a) Table 1 Cl 4.3&7.1 (Resistance to humidity Under conditions of condensation a)Resistance to humidity)	2000.0
ix.b) Table 1 Cl 4.3&7.1 (Resistance to humidity Under conditions of condensation b)Resistance to salt spray)	2000.0
x) Table 1 Cl 4.3&7.1 (Keeping properties)	5000.0
Cl 4.1 (Pigment content, percent by mass (IS:101 part 8/sec 2:1990))	1000.0
Cl 4.1.1 ANNEX B (Chromic anhydride(CrO3) content, percent by mass)	2000.0
Cl 4.1.1 ANNEX B (Zinc oxide(ZnO) content, percent by mass)	2000.0
Cl 4 (Zinc chrome content, percent by mass ( including Chromic anhydride & Zinc Oxide))	100.0
Cl 4 (Lead Restriction)	2000.0

840

IS 2046 (1995) - Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Colour and pattern)	500.0
5.2.1 (Surface Finish)	500.0
5.3 (Thickness)	1000.0
5.4.1 (Surface Defects)	1000.0
5.4.2 (Edge Defects)	1000.0
5.4.3 (Broken Corners)	1000.0
5.4.4 (Sanding Defects)	1000.0
5.4.5 (Warping (Flatness))	1000.0
5.4.6 (Length and Width)	1000.0
5.4.7 (Straightness of Edges)	1000.0
5.4.8 (Squareness of laminates)	1000.0
5.5 (Resistance to immersion in Boiling water(mass increase))	1000.0
5.5 (Resistance to immersion in Boiling water(thickness increase))	1000.0
5.5 (Resistance to suface wear)	3000.0
5.5 (Resistance to Scratching)	2000.0
5.5 (Resistance to immersion in boiling water (Appearance))	500.0
5.5.3 (Resistance to Dry Heat at 180 degC.)	2000.0
5.5 (Dimensional Stability at Elevated Temperature (L))	1500.0
5.5 (Dimensional Stability at Elevated Temperature(T))	1500.0
5.5 (Dimensional Stability at 20 degC(L))	1000.0
5.5 (Dimentional Stability at 20 degC(T))	1000.0
5.5 (Resistance to Cracking)	2000.0
5.5 (Resistance to Staining)	5000.0
5.5 (Resistance to colour change in Xenon arc light)	3000.0
5.5 (Resistance to Cigarate Burns)	2000.0
5.5 (Resistance to Steam)	2000.0