NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1230 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

781

7532 (2018) - Soft Soap — Specification

Soft Soap — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Description)	1200.0
5.3 (Consistency)	1200.0
i) (Total fatty matter, percent by mass)	1200.0
ii) (Unsaponified and unsaponifiable matter, percent by mass)	1200.0
iii) (Rosin acids, percent by mass of total fatty matter)	1200.0
iv) (Total free alkali (as K2O), percent by mass)	1200.0
v) (Free caustic alkali (as K2O), percent by mass)	1200.0

782

IRS-T-46 (1996) - Indian Railway Standard Specification for Spheroidal Graphite Cast Iron Inserts

Indian Railway Standard Specification for Spheroidal Graphite Cast Iron Inserts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

783

NTHER- Calibration of Voltage and Current Source (V/I) Method) - Calibration of Voltage and Current Source (V/I) Method

Calibration of Voltage and Current Source (V/I) Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Current Voltage)	1500.0
A.2 (Current Voltage)	2000.0

784

NTHER- Calibration of High Current Source (V/I Method) - Calibration of High Current Source (V/I Method)

Calibration of High Current Source (V/I Method)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Current)	1500.0
A.2 (Current)	2000.0
A.3 (Current)	3000.0
A.4 (Current)	4000.0

785

NTHER- Calibration of LCR Meter - Calibration of LCR Meter

Calibration of LCR Meter

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Inductance, Capacitance, Resistance)	2000.0

786

NTHER- Calibration of Signal / Function Generator - Calibration of Signal / Function Generator

Calibration of Signal / Function Generator

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Frequency)	2000.0
A.2 (Frequency)	3000.0
A.3 (Frequency)	4000.0
A.4 (Frequency)	4500.0
A.5 (Frequency)	5000.0

787

DGMS Circular(Approval) No 04 of 2013 (2013) - Revised standards for testing and use of Resin capsules as grouting ,material for Roof bolting purposes in the below ground workings of coal mines

Revised standards for testing and use of Resin capsules as grouting ,material for Roof bolting purposes in the below ground workings of coal mines

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.0.B. (Test for Compressive strength-after 30 minutes (Average compressive strength))	7500.0
2.0.B. (Test for Compressive strength-24 hrs (Average compressive strength))	7500.0
2.0.B. (Test for Bond strength Test-30 minutes (Average bond strength in Tonnes))	7500.0
2.0.A. (Test for Gel time & Setting time- For Fast set type (Average Gel time & Setting Time in seconds))	2500.0
2.0.A. (Test for Gel time & Setting time- for Slow set type (Average Gel time & Setting Time in seconds))	2500.0
2.0.A. (Test for Reaction Temperature ( deg C) (for slow setting))	1250.0
2.0.A. (Test for Thermal stability-Gel time & setting time in seconds-Fast set Type (after conditioning @ 5 deg C for 1 hr followed by 45 deg C for 1 hr))	1250.0
2.0.A. (Test for Thermal stability-Gel time & setting time in seconds-Slow set Type (after conditioning @ 5 deg C for 1 hr followed by 45 deg C for 1 hr))	1250.0
2.0.B (Test for Shear strength:(in MPa))	5000.0
2.0.B. (Test for shrinkage (only for slow type))	-
2.0.B. (Test for Flammability)	5000.0
2.0.A (Test for Reaction Temperature ( deg C) (for Fast setting))	1250.0

788

IS 17050 (2023) - Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK Code)

Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK Code)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Test to verify the protection against mechanical impact)	10000.0

789

Custom Paper Core(ER)-2022 (2022) - Paper Core

Paper Core

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dimensions)	2000.0
2.0 (Thickness)	2000.0
3.0 (Compression Strength)	2000.0

790

PCEE/NR/121-Elect/PS/2019(Rev-4) dated 04.11.2019 (2019) - LED Based Luminaries ( Input Voltage Single Phase 230 Volt AC, 50 Hz) for General Service Application.

LED Based Luminaries ( Input Voltage Single Phase 230 Volt AC, 50 Hz) for General Service Application.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1.13 (Insulation Resistance between earth and Current Carrying Parts shorted together at 500V megger & after HV Test)	2000.0
4.13 (Shall be tested at 1500 Volt AC for One Minutes between supply terminals & body of the unit.)	3000.0
3.3.8( rev. 3) (Internal Voltage Surge Protection)	1500.0
3.1.7 (Photometric Test ,as per Specification No. CEE/NR/121-Elect/PS/2018( Rev -3) dated 28.06.2018 & LM79)	18000.0

791

C/QA&I/SFQP/SCW, Rev.4 dated 29.01.2016 (2016) - Measurement of Resistivity of Gravel20/40mm

Measurement of Resistivity of Gravel20/40mm

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Measurement of Resistivity of Gravel)	20000.0

792

IS 101 (2015) - Determination of Volatile Organic Compound (VOC) Content gram per litre— Difference Method

Determination of Volatile Organic Compound (VOC) Content gram per litre— Difference Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3 (Volatile Organic Compound (VOC) Content gram per liter (on the lines of IS 101part2/Sec-1):1988 & IS 101 Part 2/Sec2):1986)	4000.0

793

RDSO MP-0.41.00.01 : Part Rev 1 (2003) - Schedule of Technical Requirements for Transition Screw Couplings for Centre Buffer Coupler

Schedule of Technical Requirements for Transition Screw Couplings for Centre Buffer Coupler

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3.3 (Destruction Test)	7500.0
7.3.2 (Impact Test)	7500.0

794

IS 104 (2017) - Ready Mixed Paint, Brushing, Zinc Chrome, Priming

Ready Mixed Paint, Brushing, Zinc Chrome, Priming

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
i) Table 1 Cl 4.3&7.1 (Consistency)	100.0
ii) Table 1 Cl 4.3&7.1 (Finish)	100.0
iii) Table 1 Cl 4.3&7.1 (Drying time-Hard dry in hours)	100.0
iv) Table 1 Cl 4.3&7.1 (Mass, kg/10 liter)	100.0
v) Table 1 Cl 4.3&7.1 (colour)	100.0
vi) Table 1 Cl 4.3&7.1 (Wet opacity, m2/10 liter)	100.0
vii.a) Table 1 Cl 4.3&7.1 (Flexibility and adhesion a. Scratch hardness (Load 1 000 g))	100.0
vii.b) Table 1 Cl 4.3&7.1 (Flexibility and adhesion b) Bend test, with 6.25 mm dia mandrel and type 1 apparatus)	100.0
viii) Table 1 Cl 4.3&7.1 (Flash point)	200.0
ix.a) Table 1 Cl 4.3&7.1 (Resistance to humidity Under conditions of condensation a)Resistance to humidity)	2000.0
ix.b) Table 1 Cl 4.3&7.1 (Resistance to humidity Under conditions of condensation b)Resistance to salt spray)	2000.0
x) Table 1 Cl 4.3&7.1 (Keeping properties)	5000.0
Cl 4.1 (Pigment content, percent by mass (IS:101 part 8/sec 2:1990))	1000.0
Cl 4.1.1 ANNEX B (Chromic anhydride(CrO3) content, percent by mass)	2000.0
Cl 4.1.1 ANNEX B (Zinc oxide(ZnO) content, percent by mass)	2000.0
Cl 4 (Zinc chrome content, percent by mass ( including Chromic anhydride & Zinc Oxide))	100.0
Cl 4 (Lead Restriction)	2000.0

795

IS 2046 (1995) - Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Colour and pattern)	500.0
5.2.1 (Surface Finish)	500.0
5.3 (Thickness)	1000.0
5.4.1 (Surface Defects)	1000.0
5.4.2 (Edge Defects)	1000.0
5.4.3 (Broken Corners)	1000.0
5.4.4 (Sanding Defects)	1000.0
5.4.5 (Warping (Flatness))	1000.0
5.4.6 (Length and Width)	1000.0
5.4.7 (Straightness of Edges)	1000.0
5.4.8 (Squareness of laminates)	1000.0
5.5 (Resistance to immersion in Boiling water(mass increase))	1000.0
5.5 (Resistance to immersion in Boiling water(thickness increase))	1000.0
5.5 (Resistance to suface wear)	3000.0
5.5 (Resistance to Scratching)	2000.0
5.5 (Resistance to immersion in boiling water (Appearance))	500.0
5.5.3 (Resistance to Dry Heat at 180 degC.)	2000.0
5.5 (Dimensional Stability at Elevated Temperature (L))	1500.0
5.5 (Dimensional Stability at Elevated Temperature(T))	1500.0
5.5 (Dimensional Stability at 20 degC(L))	1000.0
5.5 (Dimentional Stability at 20 degC(T))	1000.0
5.5 (Resistance to Cracking)	2000.0
5.5 (Resistance to Staining)	5000.0
5.5 (Resistance to colour change in Xenon arc light)	3000.0
5.5 (Resistance to Cigarate Burns)	2000.0
5.5 (Resistance to Steam)	2000.0

796

IS 14930(Part-2) (2001) - Conduit System for Electrical and Communication Installation

Conduit System for Electrical and Communication Installation

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Outside Diameter)	1000.0
8.2 (Inside Diameter)	1000.0
9.0 (Construction)	1000.0
10.2 (Compression Test)	2000.0

797

IS 1664 (2002) - Mineral mixtures for supplementing cattle feeds - Specification (Fourth Revision)

Mineral mixtures for supplementing cattle feeds - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.3 (Moisture)	500.0
6.3 (Salt as NaCl)	500.0
6.3 (Calcium (as Ca))	500.0
6.3 (Phosphorus)	500.0
6.3 (Iron Content)	500.0
6.3 (Iodine (as KI))	1000.0
6.3 (Manganese (as Mn))	500.0
6.3 (Cobalt (as Co))	1000.0
6.3 (Fluourine (as F))	1000.0
6.3 (Zinc (as Zn))	500.0
6.3 (Magnesium)	500.0
6.3 (Sulphur)	1000.0
6.3 (Acid Insoluble Ash)	500.0
6.3 (Lead (as Pb))	1000.0
6.3 (Arsenic (as As2O3))	1000.0
6.3 (Total ash in moisture free sample)	500.0
6.3 (Presence of proteinous/organic impurities)	500.0
6.3 (Acid Insoluble Ash)	500.0

798

IS 2553(1):2018 & IS 17004:2018 (2018) - SAFETY GLASS — SPECIFICATION PART 1 ARCHITECTURAL, BUILDING AND GENERAL USES & TESTING METHODS FOR PROCESSED GLASS

SAFETY GLASS — SPECIFICATION PART 1 ARCHITECTURAL, BUILDING AND GENERAL USES & TESTING METHODS FOR PROCESSED GLASS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.3.1 (Test for Thickness (IS 17004 : 2018))	2000.0

799

IS 191 (2007) - Copper - Specification (Fourth Revision)

Copper - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Copper + Silver )	2000.0

800

IRS:M-46 (2020) - INDIAN RAILWAYS STANDARD SPECIFICATION FOR CLASSIFICATION, TESTING AND ACCEPTANCE CRITERIA OF FILLER WIRES FOR MIG/MAG WELDING (WITH AND WITHOUT GAS SHIELDING)

INDIAN RAILWAYS STANDARD SPECIFICATION FOR CLASSIFICATION, TESTING AND ACCEPTANCE CRITERIA OF FILLER WIRES FOR MIG/MAG WELDING (WITH AND WITHOUT GAS SHIELDING)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Size of Wire : Diameter)	500.0
3.2 (Tensile Strength of Wire)	3000.0
6.2.5 (Carbon)	500.0
6.2.5 (Manganese)	500.0
6.2.5 (Silicon)	500.0
6.2.5 (Phosphorus)	500.0
6.2.5 (Molybdenum)	500.0
6.2.5 (Nickel)	500.0
6.2.5 (Copper)	500.0
6.2.5 (Chromium)	500.0
6.2.5 (Vanadium)	500.0
6.2.5 (Sulphur)	500.0

801

NTHER- Calibration of Earth Resistivity Tester - Calibration of Earth Resistivity Tester

Calibration of Earth Resistivity Tester

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Resistance)	1200.0
A.2 (Resistance)	1800.0
A.3 (Resistance)	2400.0

802

JAPANESE INDUSTRIAL STANDARD JIS K 5659 (2018) - JAPANESE INDUSTRIAL STANDARD JIS K 5659 -Long Durable Paints for Steel Structures

JAPANESE INDUSTRIAL STANDARD JIS K 5659 -Long Durable Paints for Steel Structures

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.4 (Condition inside container As per 4.1.2 a of JIS K5600-1-1)	1200.0
7.5 (Low temperature stability at (-5 deg.C) As per 3.3.7 of JIS K5600-1-1)	5000.0
7.6 (Surface Drying Property as per JIS K 5600)	1200.0
7.7 (Appearance of the Film ( As per of JIS K5600-1-1 ))	1200.0
7.8 (Pot life)	1500.0
7.9 (Contrast Ratio % As per of JIS K5600-4-1)	1500.0
7.10 (Specular Gloss (60º) as per JIS K5600-4-7)	1200.0
7.11 (Overcoatability)	1200.0
7.12 (Flexibility 10 mm dia mandrel of type I tester as per JIS 5600-5-1)	1200.0
7.13 (Falling weight Resistance 300 gram weight& drop height 500 mm (As per JIS K 5600-5-3))	1500.0
7.14 (Interlayer adhesion-I(between undercoat and intermediate coat))	2000.0
7.15 (Interlayer adhesion-II(between Intermediate coat & top coat))	2000.0
7.16 (Alkali Resistance (dilute Calcium Hydroxide),Immersing method, for 168 Hours at 23 ±1 Deg c)	1500.0
7.18 (Humidity and Cool-Heat Cycling Resistance Test Condition :Immersion in water at 23 Deg C for 18 hours followed by cooling at -20 deg C for 03 Hours ,Heat at 50 deg C for 03 hours (10 Cycles))	10000.0
7.20 (Accelerated weathering Resistance- Xenon arc Exposure period 2000 hours As per of JIS K5600-7-7)	120000.0
7.20 b (Accelerated weathering Resistance by Xenon arc Exposure period 500 hours) after 24 Months Natural Weathering Resistance test (As per of JIS K5600-7-7))	15000.0
7.21 (Natural Weathering Resistance (for 24 Months) as per JIS K 5600-7-6)	20000.0
7.17 (Acid Resistance (dilute Sulfuric Acid 5gram per litre),Immersing method, for 168 Hours at 23 ±1 Deg c)	1500.0
7.19 (Non Volatile Matter content % As per JIS K 5601-1-2)	1200.0

803

JIS K 5674 :2008 (2008) - LEAD-FREE, CHROMIUM-FREE ANTICORROSIVE PAINTS

LEAD-FREE, CHROMIUM-FREE ANTICORROSIVE PAINTS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 5 Table 1 (Please see Annexure)	25000.0

804

JIS K 5552:2010 (2010) - ZINC RICH PRIMER

ZINC RICH PRIMER

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 5 Table 1 (Please see Annexure)	25000.0

805

JIS K 5553 : 2002 (2002) - HIGH BUILD TYPE ZINC RICH PAINT

HIGH BUILD TYPE ZINC RICH PAINT

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 5 ,Table 1 (Please see Annexure)	30000.0

806

JIS K 5551:2008 (2008) - HEAVY DUTY ANTICORROSIVE PAINTS FOR METAL STRUCTURES

HEAVY DUTY ANTICORROSIVE PAINTS FOR METAL STRUCTURES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 5 Table 2 (Please see Annexure)	30000.0

807

IS 16676 (2017) - Solventless liquid epoxy system for application on interior and exterior surfaces of steel water pipeline - Specification

Solventless liquid epoxy system for application on interior and exterior surfaces of steel water pipeline - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Vii (Solvent Rub Test)	1200.0
Vi (Cathodic Disbondment Test, Max)	2000.0
V (Abrasion Resistance, Max)	2000.0
IV (c) (Immersion & vapour phase c) Sodium hydroxide pass 1 percent by weight)	2000.0
IV (b) (Immersion & vapour phase b) Sulphuric acid pass 1 percent by weight.)	2000.0
IV (a) (Immersion & vapour phase a) De-ionized water)	2000.0
III (a) (Adhesion Test a)Tape Test)	1200.0
III (b) (Adhesion Test b)Pull off Test.)	2500.0
II (Electrical insulation (holidays))	2500.0
6.7 Table 1 I (Thickness, dry film, Min)	1200.0
6.6 (Keeping Properties)	2500.0
6.5 (Consistency)	1200.0
6.4 (Recoating Properties)	1200.0
6.3 (Application Properties)	1200.0
6.2 (Thinning)	1200.0
6.1 (Condition)	1200.0

808

JIS K 5659:2018 (2018) - LONG DURABLE PAINTS FOR STEEL STRUCTURES

LONG DURABLE PAINTS FOR STEEL STRUCTURES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clause 5 Table 2 Top Coat Type A (Please see Annexure)	40000.0
Clause 5 Table 2 Intermediate CoatType A (Please see Annexure)	40000.0
Clause 5 Table 2 Top Coat Type B (Please see Annexure)	1.0
Clause 5 Table 2 Type B Intermediate Coat (Please see Annexure)	1.0
5 Table 2 LONG DURABLE PAINTS FOR STEEL STRUCTURES ( ZINC RICH PRIMER) TYPE A (Please see Annexure)	55000.0
5 Table 2 (LONG DURABLE PAINTS FOR STEEL STRUCTURES( Intermediate) TYPE A (Please see Annexure)	45000.0
5 Table 2 LONG DURABLE PAINTS FOR STEEL STRUCTURES (Undercoat) TYPE A (Please see Annexure)	20000.0
5 Table 2 LONG DURABLE PAINTS FOR STEEL STRUCTURES( FINISH) TYPE A (Please see Annexure)	50000.0

809

IS 12894 (2002) - Pulverized fuel ash - Lime bricks - Specification

Pulverized fuel ash - Lime bricks - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.2 (Drying Shrinkage)	2000.0
7.3 (Efforescence)	1000.0
7.4 (Water Absorption)	1000.0
7.1 (Crushing Strength)	2000.0
5 (Dimensions)	500.0
3 (General quality)	500.0

810

RDSO/M&C/RP-198 (2006) - COMPOSITE GROOVED RUBBER SOLE PLATES FOR PLACING BENEATH RAILS

COMPOSITE GROOVED RUBBER SOLE PLATES FOR PLACING BENEATH RAILS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Hardness)	1000.0
3.2 (Compression Set)	3000.0
3.2 (Relaxed Modulus at 100% elongation before ageing)	1000.0
3.2 (Tension Set)	3000.0
3.2 (Electrical Resistance after immersion)	5000.0
3.2 (Electrical Resistance Before immersion)	5000.0
3.2.2 (Ash Content)	2000.0
3.2.2 (Specific Gravity)	1000.0
3.2 (Relaxed Modulus at 100% elongation, Change after ageing)	1000.0
3.2 (Elongation at break, Before ageing)	1500.0
3.2 (Elongation at Break, After ageing)	1500.0
3.2 (Elongation at Break, Retention after ageing)	1000.0
3.2 (Tensile Strength, Before ageing)	1500.0
3.2 (Tensile Strength, After ageing)	1500.0
3.2 (Tensile Strength, Retention after Ageing)	1000.0
3.1.3 (Thickness of Composite Pad)	1000.0