NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1226 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

751

IS 9862 (2017) - Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision)

Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Lead Restriction as metallic lead)	1500.0
4.3 table 1(i) (Drying time a) Hard dry)	1500.0
4.3 table 1(ii) (Consistency)	1000.0
4.3 table 1(iii) (Finish)	500.0
4.3 table 1(iv) (Wet opacity meter square per liter)	500.0
4.3 table 1(v) (Mass, kg/10 Litres,)	1000.0
4.3 table 1(vi) (Colour)	200.0
4.3 table 1(vii) (Flexibility and adhesion (bend test of the film with 6.25 dia Mandrel in type 1 apparatus))	1000.0
4.3 table 1(viii) (Stripping test ( By scratch hardness tester))	1000.0
4.3 table 1(ix) (Flash point deg.C)	1000.0
4.3 table 1(x) (Volatile matter content, percent by mass,)	1000.0
4.3 table 1(xi) (Resistance to humidity under conditions of condensation)	2000.0
4.3 table 1(xii) (Resistance to water)	1000.0
4.3 table 1(xiii) (Resistance to acid (Dilute Sulphuric Acid 1: 20 (v/v))	1500.0
4.3 table 1(xiv) (Resistance to alkali (Sodium Carbonate 5 % m/v Solution))	1500.0
4.3 table 1(xv) (Resistance to chlorine (0.05 percent of chlorine (m/v).)	1000.0
4.3 table 1(xvi) (Water content (if water is suspected to be present), percent by mass,)	1500.0
4.3 table 1(xvii) (Keeping properties(12 Months))	5000.0

752

Civil lab Training - Evaluation of Building Materials through Quality Testing & Standard specification-Training

Evaluation of Building Materials through Quality Testing & Standard specification-Training

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Training)	5000.0

753

F-17 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-17 Technical Name: Novolac epoxy phenolic coating cured with polyamine adduct hardener . HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-17 Technical Name: Novolac epoxy phenolic coating cured with polyamine adduct hardener . HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Potlife at 30 deg C for 2 component paints, hours)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2500.0
10 (Temperature resistance 150 ⁰ C (ASTM D 2485 method A))	4000.0
11 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
12 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
13 (Volatile Matter (% by mass) Component-A (Base))	1200.0
14 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
15 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
16 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
17 (Ash Content (% by mass)Component-A (Base))	1200.0
18 (Ash Content (% by mass)Component-B (Accelerator ))	1200.0

754

F-16 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-16 Technical Name: Inert polymeric matrix coating suitable for under insulation for CS and SS. HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-16 Technical Name: Inert polymeric matrix coating suitable for under insulation for CS and SS. HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Potlife at 30 deg C for 2 comp paints, hours)	1200.0
9 (Temperature resistance 650 ⁰ C (ASTM D 2485 method B))	4200.0
10 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
11 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
12 (Volatile Matter (% by mass) Component-A (Base))	1200.0
13 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
14 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
15 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
16 (Ash Content (% by mass)Component-A (Base))	1200.0
17 (Ash Content (% by mass)Component-B (hardener ))	1200.0

755

F-15 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-15 Technical Name: Two component epoxy phenolic coating cured with polyamine adduct hardener HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-15 Technical Name: Two component epoxy phenolic coating cured with polyamine adduct hardener HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Potlife at 30 deg C for 2 comp paints, hours)	2000.0
9 (Adhesion ASTM D 4541 (Mpa))	2500.0
10 (Temperature resistance 150 ⁰ C (ASTM D 2485 method A))	4000.0
11 (Full cure at 30 Deg C (for immersion / high temperature service))	1500.0
12 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
13 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
14 (Volatile Matter (% by mass) Component-A (Base))	1200.0
15 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
16 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
17 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
18 (Ash Content (% by mass)Component-A (Base))	1200.0
19 (Ash Content (% by mass)Component-B)	1200.0

756

High Polymer Cus specification (2003) - Wrapping Coating Material

Wrapping Coating Material

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.5 Viii (Solubility of coal tar based tape in petrol,% by mass C-2 SOLUBILITY OF COAL TAR BASED TAPE IN PETROL IS 15337:2003 RA 2018 (Annex c))	5000.0

757

NTH/ER/CHEM/Acidity - Total acidity of Transformer Oil

Total acidity of Transformer Oil

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Total acidity of transformer oil)	1200.0

758

Custom-17-ER-LM - TRAINING

TRAINING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Training)	132000.0

759

NTH/ER/CHEM/Alumina - Alumina content as Al2O3 in Fire Brick

Alumina content as Al2O3 in Fire Brick

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Alumina Content as Al2O3)	2000.0

760

F-12 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-12 Technical Name: Heat resistant silicone aluminium paint suitable upto 540 Deg C dry temperature HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-12 Technical Name: Heat resistant silicone aluminium paint suitable upto 540 Deg C dry temperature HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Temperature resistance 540 ⁰ C Dry Service (ASTM D 2485 method B))	4200.0
9 (Temperature resistance540 ⁰ C (ASTM D 2485 method B))	1200.0
10 (Non Volatile Matter (% by mass))	1200.0
11 (Volatile Matter (% by mass))	1200.0
12 (Specific Gravity (ASTM D1475))	1200.0
13 (Ash Content (% by mass))	1200.0

761

F-11 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-11 Technical Name: Heat resistant synthetic medium based two pack Aluminium paint suitable upto 250 deg C dry temperature HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-11 Technical Name: Heat resistant synthetic medium based two pack Aluminium paint suitable upto 250 deg C dry temperature HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Temperature resistance250 ⁰ C (ASTM D 2485 method A))	4200.0
9 (Non Volatile Matter (% by mass) Component-A -Aluminium Paste)	1200.0
10 (Non Volatile Matter (% by mass) Component-B (Accelerator))	1200.0
11 (Volatile Matter (% by mass) Component-A Aluminium Paste)	1200.0
12 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
13 (Specific Gravity Component-A Aluminium Paste (ASTM D1475))	1200.0
14 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
15 (Ash Content (% by mass)Component-B (Accelerator))	1200.0
16 (Temperature resistance 250 ⁰ C (ASTM D 2485 method B))	1000.0

762

F-9 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-9 Technical Name :Inoranic zinc silicate coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-9 Technical Name :Inoranic zinc silicate coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max)	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Pot life at 30⁰C for two component paints, hrs)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Temperature resistance 400 ⁰ C (ASTM D 2485 method B))	1000.0
11 (Temperature resistance 400 ⁰ C Dry Service (ASTM D 2485 method B))	2000.0
12 (Zinc Content as Zn in dry film % by mass)	1200.0
13 (MEK rub test ASTM D 4752)	1200.0
14 (Non Volatile Matter (% by mass) Component-A Zinc dust)	1000.0
15 (Non Volatile Matter (% by mass) Component-B liquid accelerator)	1000.0
16 (Volatile Matter (% by mass) Component-A Zinc dust)	1200.0
17 (Volatile Matter (% by mass) Component-B liquid accelerator)	1200.0
18 (Specific Gravity Component-A Zinc dust (ASTM D1475))	1200.0
19 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
20 (Ash Content (% by mass)Component-A Zinc dust)	1200.0
21 (Ash Content (% by mass)Component-B Liquid Accelerator)	1200.0

763

F-8 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-8 Technical Name: Self priming surface tolerant high build epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-8 Technical Name: Self priming surface tolerant high build epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Pot life at 30⁰C for two component paints, hrs)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Temperature resistance 80 ⁰ C (ASTM D 2485 method A))	1000.0
11 (Temperature resistance 80 ⁰ C (ASTM D 2485 method B))	2000.0
12 (Full cure at 30 Deg C (for immersion / high temperature service))	1200.0
13 (Non Volatile Matter (% by mass) Component-A (Base))	1000.0
14 (Non Volatile Matter (% by mass) Component-B (Hardener))	1000.0
15 (Volatile Matter (% by mass) Component-A (Base))	1200.0
16 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
17 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
18 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
19 (Ash Content (% by mass)Component-A (Base))	1200.0
20 (Ash Content (% by mass)Component-B)	1200.0

764

Customised specification for Cumin Powder - Customised specification for Cumin Powder

Customised specification for Cumin Powder

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Description)	500.0
2 (Moisture, Percent by mass)	500.0
3 (Total ash ,Dry basis ,Percent by mass)	500.0
4 (Acid insoluble ash on dry basis, Percent by mass)	500.0
5 (Volatile oil on dry basis, Percent by mass)	500.0
6 (Non Volatile ether extract , Percent by mass)	500.0
7 (Salmonella (in 25 g))	500.0

765

F-7 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-7 Technical Name High build coal tar epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-7 Technical Name High build coal tar epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Pot life at 30⁰C for two component paints, hrs)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Temperature resistance 80 ⁰ C (ASTM D 2485 method A))	1200.0
11 (Temperature resistance 80 ⁰ C (ASTM D 2485 method B))	1200.0
12 (Full cure at 30 Deg C (for immersion / high temperature service))	1200.0
13 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
14 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
15 (Volatile Matter (% by mass) Component-A (Base))	1200.0
16 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
17 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
18 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
19 (Ash Content (% by mass)Component-A (Base))	1200.0
20 (Ash Content (% by mass)Component-B)	1200.0

766

Customised Specification Organic Manure (On the lines of FCO-1985) - Customised Specification Organic Manure (On the lines of FCO-1985)

Customised Specification Organic Manure (On the lines of FCO-1985)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Moisture, Percent by weight)	1000.0
3 (Bulk density (g/cm Sq.))	1000.0
4 (Total Organic matter (percent by weight))	1000.0
5 (Total Organic carbon (percent by weight))	1000.0
6 (Total Nitrogen (as N), percent by weight)	1000.0
7 (Total Phosphates (As P2O5), Percent by weight)	1000.0
8 (Total potassium (as K2O), percent by weight)	1000.0
9 (Calcium (as Ca), mg/kg)	1000.0
10 (Magnesium (as Mg), mg/Kg)	1000.0
11 (Iron (as Fe), mg/Kg)	1000.0
12 (Zinc (as Zn), mg/Kg)	1000.0
2 (pH (dilution at 10%))	1000.0

767

F-6 C EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-6 C Technical Name : Solventless epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-6 C Technical Name : Solventless epoxy coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds % minimum)	1200.0
2 (DFT per coat microns)	1200.0
3 (Theoretical covering capacity in m sq/coat/litre)	1200.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Potlife at 30 deg C for 2 component paints, hours)	1200.0
9 (Full cure at 30oC (for immersion/ high temperature service))	1200.0
10 (Adhesion ASTM D 4541 (Mpa))	2000.0
11 (Temperature resistance (ASTM D 2485 Methods A))	1200.0
12 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
13 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
14 (Volatile Matter (% by mass) Component-A (Base))	1200.0
15 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
16 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
17 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
18 (Ash Content (% by mass)Component-A (Base))	1200.0
19 (Ash Content (% by mass)Component-B)	1200.0

768

F-6B EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-6B Technical Name :Epoxy high build coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-6B Technical Name :Epoxy high build coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	1000.0
2 (DFT per coat, microns)	1000.0
3 (Theoretical covering capacity in m sq/coat/litre)	1000.0
4 (Weight per liter in kg/litre)	1200.0
5 (Touch dry at 30 Deg c max (hours))	1200.0
6 (Hard dry at 30 deg C max(hours))	1200.0
7 (Over coating interval , hours)	1200.0
8 (Potlife at 30 deg C for 2 component paints, hours)	1200.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Non Volatile Matter (% by mass) Component-A (Base))	1200.0
11 (Non Volatile Matter (% by mass) Component-B (Hardener))	1200.0
12 (Volatile Matter (% by mass) Component-A (Base))	1200.0
13 (Volatile Matter (% by mass) Component-B (Hardener))	1200.0
15 (Ash Content (% by mass)Component-A (Base))	1200.0
16 (Ash Content (% by mass)Component-B)	1200.0
17 (Specific Gravity Component-A (Base) (ASTM D1475))	1200.0
18 (Specific Gravity Component-B curing agent(ASTM D1475))	1200.0
19 (Temperature resistance 80 ⁰ C (ASTM D 2485 method A))	1000.0
1.1 (Colour as per Manufacturer’s supply shade’)	100.0

769

F-6A EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-6A Technical Name :Epoxy high build coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

F-6A Technical Name :Epoxy high build coating HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	1000.0
2 (DFT per coat, μ)	1000.0
3 (Theoretical covering capacity in m2/coat/ litre)	1000.0
4 (Weight per litre in Kg/litre)	1000.0
5 (Touch dry at 30DegC (max.))	1000.0
6 (Hard dry at 30Deg.C (max.))	1000.0
7 (Full cure at 30 deg.C (for immersion/ high temperature service))	1000.0
8 (Over-coating interval, hrs)	1000.0
9 (Pot life at for two component paints, hrs)	1000.0
10 (Adhesion (ASTM D 4541))	2000.0
11 (Temperature resistance 80 deg.C for 24 hrs (ASTM D 2485 Method A))	2000.0
12 (Non Volatile Matter (% by mass) Component-A (Base))	1000.0
13 (Non Volatile Matter (% by mass) Component-B (Hardener))	1000.0
14 (Volatile Matter (% by mass) Component-A (Base))	1000.0
15 (Volatile Matter (% by mass) Component-B (Hardener))	1000.0
16 (Specific Gravity Component-A (Base) (ASTM D1475))	1000.0
17 (Specific Gravity Component-B curing agent(ASTM D1475))	1000.0
18 (Ash Content (% by mass)Component-A (Base))	1000.0
19 (Ash Content (% by mass)Component-B)	1000.0

770

F-2 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - F-2 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name : Aliphatic PU finish paint

F-2 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name : Aliphatic PU finish paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	1000.0
2 (DFT per coat, microns)	1000.0
3 (Theoretical covering capacity in m sq/coat/litre)	1000.0
4 (Weight per liter in kg/litre)	1000.0
5 (Touch dry at 30 Deg c)	500.0
6 (Hard dry at 30 deg C max)	500.0
7 (Over coating interval , hours)	1000.0
8 (Potlife at 30 deg C for 2 component paints, hours)	1000.0
9 (Adhesion ASTM D 4541 (Mpa))	2000.0
10 (Abrasion Resistance, mg per 1000gm/CS17/1000cycle (ASTM D4060))	2000.0
11 (Temperature resistance 80⁰ C (ASTM D 2485 Method A))	2000.0
12 (Non Volatile Matter, % By mass Component-A (Base))	1000.0
13 (Non Volatile Matter, % By mass Component-B (Hardener))	1000.0
14 (Volatile Matter, % By mass Component-A (Base))	1000.0
15 (Volatile Matter, % By mass Component-B (Hardener))	1000.0
16 (Specific gravity of base (ASTM D1475))	1000.0
17 (Specific gravity of Curing agent (ASTM D1475))	1000.0
18 (Ash Content, % By mass Component-A (Base))	1000.0
19 (Ash Content, % By mass Component-B (Hardener))	1000.0

771

P-6 EIL SPEC B224-000-79-41-PLS-01 REV6 (2021) - P-6 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name :Epoxy zinc phosphate primer

P-6 HRRL JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS Technical Name :Epoxy zinc phosphate primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume soilds %)	2000.0
2 (DFT per coat microns)	100.0
3 (Theoretical covering capacity in m sq/coat/litre)	1000.0
4 (Touch dry at 30 Deg c max (hours))	1000.0
5 (Hard dry at 30 deg C max(hours))	1000.0
6 (Over coating interval , hours)	1000.0
7 (Potlife at 30 deg C for 2 comp paints, hours)	1000.0
8 (Adhesion ASTM D 4541 (Mpa))	5000.0
9 (Temperature resistance min deg C 80 METHOD A ASTM D2485)	3000.0
10 (Non Volatile Matter % By mass Component-A (Base))	1000.0
11 (Non Volatile Matter % By mass Component-B (Hardener))	1000.0
12 (Volatile Matter % By mass Component-A (Base))	500.0
13 (Volatile Matter % By mass Component-B (Hardener))	500.0
14 (Specific Gravity Component-A (Base))	500.0
15 (Specific Gravity Component-B (Hardener))	500.0
16 (Ash content Component-A (Base))	1000.0
17 (Ash Content % By mass Component-B (Hardener))	1000.0
10 (weight per litre in kg/litre)	500.0
11 (Abrasion Resistance(ASTM D4060)1000gm load/1000Cycles CS17 wheel or CS 10 wheel)	2000.0

772

NTH ER PAINT LAB CUSTOMER SPECIFICATION (2012) - PAINT ,RFU,FINISHING,MATT AIR DRYING BRUSHING /SPRAYING

PAINT ,RFU,FINISHING,MATT AIR DRYING BRUSHING /SPRAYING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Film strength at impact Impact Resistance Test (ASTM D 2794))	2000.0
2 (Hardness test: Pencil Hardness test IS:101(part 5/Sec1)1988 (Reaffirmed2019).)	1000.0
3 (Scratch Hardness test (1500 g weight) for pencil hardness up to 2H IS 101 Part 5 sec 2 RA 2019)	1000.0
4 (Drying Time a) Surface Dry IS 101 (Part 3/sec 1), 1986)	1000.0
5 (Drying Time b) Hard Dry &tack free IS 101 (Part 3/sec 1), 1986)	1000.0
6 (Specular Gloss at 60 º IS 101 (Part 4/Sec 4))	1000.0
7 (Finish IS 101 part 3 sec 4,1987)	1000.0
8 (Fineness of Grind ,in microns IS 101 part 3 section 5)	1000.0
9 (Mass in kg/10 ltrs IS 101 part 1 sec 7)	1000.0
10 (Accelerated Weathering Test QUV –UVA lamp 340 nm For10 days(at Basic Climate Condition) MIL Std -810-G)	20000.0
11 (Resistance to Petrol -Benzene Mixture Immersion test jSS-8010-82:2012,Appendix -D.)	2000.0
12 (Resistance to Warm water jSS-8010-82:2012,Appendix-E)	1000.0
13 (Accelerated Storage Stability Duration 96 hours at 60 Deg .C jSS-8010-82:2012,Appendix -C.)	2000.0
14 (Resistance to salt Water:- 7 Cycles JSS-8010-82:2012,Appendix -F. Test Condition (one Cycle):-One Hour immersion in salt water Three Hours outside exposure at angle of 45 Deg Facing south then one hour refrigeration at 4 plus minus 2 Deg C then again exposued angle of 45 Deg Facing south till next cycle)	3500.0
15 (Resistance to Lubricating oil (immersion test for 2 hours at 50 Deg c jSS-8010-82:2012,Appendix -A.)	1000.0
16 (Resistant to heat (at 150 deg c for 2 hours) JSS-8010-82:2012,Appendix-B)	1000.0
17 (Resistance to low temperature for 120 hours at-20 deg c (+/- 0.1 deg c ))	5000.0
18 (Accelerated weathering Test Xenon Radiation For 30days as per moderate climatic conditions. MIL STD -810-G.)	40000.0
6 (ANTI GRAFFITI PROPERTIES ASTM D 6578)	5000.0
1.2 (COVERING STRENGTH covering strength must be tested on a Garmsen clear glass plate with a minimum dry film thickness applied according to WN 11500 over a black and white contrast card. There may be no visible contrast between the black and white backgrounds.)	2500.0

773

13209 (2024) - Indelible Ink-Specification

Indelible Ink-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Description)	1000.0
3.3 (Colour)	1000.0
3.4 (pH)	1000.0
3.5 (Total solids)	1000.0
3.6 (Development)	1000.0
3.7.1 (Performance- Resistance to Bleaching)	1000.0
3.7.2 (Performance- Resistance to organic solvents)	1000.0

774

IS 12894:2002 (On the lines, comparative tests for Fly ash bricks) (2002) - Pulverized Fuel ash lime bricks-Specification

Pulverized Fuel ash lime bricks-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Comparative tests for fly ash bricks (on the lines of IS 12894:2002))	14000.0

775

IS 15658:2021-(on the lines,Comparative Tests for Paver blocks) (2021) - Concrete Paving Blocks-Specification

Concrete Paving Blocks-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1. (Comparative tests as per IS 15658:2021)	32000.0

776

Custom - Testing of Gold Plated Silver Medal

Testing of Gold Plated Silver Medal

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Silver, Percent by mass)	2000.0
2 (Gold (Qualitative))	1000.0
3 (Thickness of Gold plating on silver medal.)	2000.0
0 (Weight (gm))	1000.0

777

7532 (2018) - Soft Soap — Specification

Soft Soap — Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Description)	1200.0
5.3 (Consistency)	1200.0
i) (Total fatty matter, percent by mass)	1200.0
ii) (Unsaponified and unsaponifiable matter, percent by mass)	1200.0
iii) (Rosin acids, percent by mass of total fatty matter)	1200.0
iv) (Total free alkali (as K2O), percent by mass)	1200.0
v) (Free caustic alkali (as K2O), percent by mass)	1200.0

778

IRS-T-46 (1996) - Indian Railway Standard Specification for Spheroidal Graphite Cast Iron Inserts

Indian Railway Standard Specification for Spheroidal Graphite Cast Iron Inserts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

779

NTHER- Calibration of Voltage and Current Source (V/I) Method) - Calibration of Voltage and Current Source (V/I) Method

Calibration of Voltage and Current Source (V/I) Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Current Voltage)	1500.0
A.2 (Current Voltage)	2000.0

780

NTHER- Calibration of High Current Source (V/I Method) - Calibration of High Current Source (V/I Method)

Calibration of High Current Source (V/I Method)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A.1 (Current)	1500.0
A.2 (Current)	2000.0
A.3 (Current)	3000.0
A.4 (Current)	4000.0