NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb@nic.in

Scope List

Reset

1187 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

451

M&C/ PCN/ 127 /2020 (Rev 2.0 ) Dated Sep 2020 (2020) - RDSO Specification for Anti-Graffiti Clear coat for the exterior painting of Railway coaches, Diesel & Electric locomotives”

RDSO Specification for Anti-Graffiti Clear coat for the exterior painting of Railway coaches, Diesel & Electric locomotives”

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying Time at (27± 2)˚C , i)Surface Dry/Touch Dry As per IS:101-86 (Part- 3/ Sec- 1)Reaffirmed 2017)	400.0
1 (Drying Time at (27± 2)˚C ii)Hard Dry As per IS:101-86 (Part- 3/ Sec- 1)Reaffirmed 2017)	400.0
1 (Drying Time at (27± 2)˚C iii) Recoating Time As per IS:101-86 (Part- 3/ Sec- 1)Reaffirmed 2017)	400.0
2 (Finish (IS 101 (Part 3/Sec 4): 1987)	400.0
3 (Gloss at 60˚ IS : 101-88 (Part 4/Sec-4),)	1200.0
4 (Flexibility & Adhesion (By Mandrel size 6.25 mm) IS : 101-88 (Part -5/Sec-2),)	1200.0
5 (Impact Resistance test at Height 100cm (39.37 inch) and weight 2.0 Kg (4.409 pound) on 0.50 mm thick cured panel. ASTM-D-2794)	1500.0
6 (Adhesion Test ( Cross Cut Tape Test) ASTM-D-3359)	1200.0
7 (Consistency/Efflux Time at (27± 2)˚C IS : 101-89 (Part -1 Sec-5),)	1500.0
8 (Protection against corrosion under conditions of condensation (500 hrs) IS: 101-88 (Part- 6 /Sec- 1),)	15000.0
9 (Solvent MEK Rub Test 100 DS ASTM D-5402)	1500.0
10(a) (ACCELERATED TESTS Resistance to 30 % ,w/v (a)Citric acid for 3 Hours appendix III)	1000.0
10(b) (ACCELERATED TESTS (b) Resistance to 5% ,v/v Ammonia for 20 Minutes appendix III)	1000.0
10(c) (ACCELERATED TESTS (c) Resistance to Lubricating oil for 24 Hours appendix III)	1000.0
10(d) i (ACCELERATED TESTS (d) Resistance to Solvents for 20 Minutes (i)Acetone appendix III)	1000.0
10(d) ii (ACCELERATED TESTS d) Resistance to Solvents for 20 Minutes (ii) Toluene appendix III)	1000.0
11 (Mass in Kg/10 litres (IS : 101-87 (Part -1/ Sec7),Reaffirmed 2019))	1000.0
12 (Flash Point deg.C (IS: 101-87 (Part- 1/ Sec6),Reaffirmed 2019))	1000.0
13 (Keeping Property/Shelf Life for 1 year)	10000.0
14 (Anti Graffiti test ASTM D-6578)	5000.0
16 (Coverage ( Spreading Capacity) , Min. , at 1-4 microns DFT, By Spray, Dipping, Roller, Wiping method appendix-I)	1200.0
17 (Dry Film Thickness per coat in micron, by Wipe/Spray APPENDIX-I)	1000.0
18 (Pencil Hardness ASTM –D- 3363)	1500.0
19 (Volume Solid,% APPENDIX-I)	2000.0
20 i (Durability Tests : Accelerated Weathering by (Fluorescent UV-Condensation Type for 750 Hours ASTM-G-154 (APPENDIX-IV) Cycle 4 Hrs. U.V. Light from UV-B lamps with a peak emission @ 313 nm. and 4 Hours Condensation alternatively, temp. 50 ˚C)	45000.0
20 ii (Durability Tests : Accelerated Weathering by Xenon Arc for 2000hours DIN- 53387 Superseded by DIN EN ISO 4892-2)	120000.0

452

FCO 1985 (Annexure) - FCO-1985 (Annexure)

FCO-1985 (Annexure)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1 to 3 test parameters)	2000.0
2 (4 to 6 parameters (Vide Annexure))	4000.0
3 (7 or more parameters (Vide annexure))	7000.0

453

BS EN 14901-1:2014+A1:2019 (Nov 2019) - Ductile Iron Pipes ,Fittings and Accessories Requirements and Test Methods for Organic Coatings of Ductile Iron Fittings and Accessories Part-1 Epoxy Coatings(Heavy duty)

Ductile Iron Pipes ,Fittings and Accessories Requirements and Test Methods for Organic Coatings of Ductile Iron Fittings and Accessories Part-1 Epoxy Coatings(Heavy duty)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1.Heat ageing resistance in air (Annexure A Table A.1) Durability: Cl 7.2.5.1 (Test condition: stored in Hot air oven at 110(+/-2)Deg C for 30 Days & Tested for Non Porosity as read in cl No 7.2.4))	7500.0
2 (Heat ageing resistance in air (Annexure A Table A.1) Durability: Cl 7.2.5.1 (Test condition: stored in Hot air oven at 110(+/-2)Deg C for 60 Days& Tested for Non Porosity as read in cl No 7.2.4))	7500.0
3 (Heat ageing resistance in air (Annexure A Table A.1) Durability: Cl 7.2.5.1 (Test condition: stored in Hot air oven at 110(+/-2)Deg C for 90 Days & Tested for Non Porosity as read in cl No 7.2.4))	7500.0
4 (Heat aging resistance in Water Test Condition :Immersion in deionized Water at 70 (+/-2)Deg for 07 Days followed by adhesion test) Adhesion in MPa)	5000.0
5 (.Chemical Resistance for Coatings in swear Applications a) Sulphuric Acid at PH-3(EN 598 as read in Cl No 7.9.2 ) at 18 (+/-2)Deg C Test Duration 06 months)	10000.0
6 (Chemical Resistance for Coatings in swear Applications b) Sodium Hydroxide at PH-13(EN 598 r as read in Cl No 7.9.2 ) (+/-2)Deg C Test Duration 06 months)	10000.0
7 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days i) pH)	1000.0
8 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days .ii) Turbidity (NTU))	1000.0
9 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days iii) Total Hardness (asCaCO3), mg/l)	1000.0
11 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days iv) Chloride (Cl) mg/l)	1000.0
12 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days v) Nitrate (as NO3), mg/l)	1000.0
13 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days Vi) Iron (as Fe), mg/l)	1000.0
10 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days vii) Arsenic (as As), mg/l)	1000.0
14 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days viii) Fluoride (as F), mg/l)	1000.0
15 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days ix)Cadmium ), mg/l)	1000.0
16 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days X Chromium ), mg/l)	1000.0
17 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days xi)Mercury ), mg/l)	1000.0
18 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days xii Lead ), mg/l)	1000.0
20 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days ix) Total Coliform (CFU/100 ml))	1500.0
19 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days x) Faecal Streptococc CFU/100 ml))	1500.0
21 (4. Material in contact with potable water Leaching of Metals &micro organisms from the product into Water after water Kept in contact for 30 Days xi) Odour &Taste)	2000.0
additional parameter 1 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours a) odour &Flovour: b) odour &Flovour:)	5000.0
additional parameter 2 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours a)TDS b)TDS)	2000.0
additional parameter 3 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Leaching of Heavy Metals in ppm a)Chromium (as Cr) b) Chromium (as Cr))	2000.0
additional parameter 4 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Leaching of Heavy Metals in ppm a) Manganese(as Mn) b)Manganese(as Mn))	2000.0
additional parameter 6 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Leaching of Heavy Metals in ppm a)Cobalt(as CO) b)Cobalt(as CO))	2000.0
additional parameter 7 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Leaching of Heavy Metals in ppm d) Nickel(as Ni) d) Nickel(as Ni))	2000.0
additional parameter7 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Leaching of Heavy Metals in ppm a) Arsenic (as As) b)Arsenic (as As))	3000.0
additional parameter 8 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Leaching of Heavy Metals in ppm a)Cadmium (as Cd) b)Cadmium (as Cd))	3000.0
additional parameter 10 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Leaching of Heavy Metals in ppm a)Mercury(as Hg) b)Mercury(as Hg))	3000.0
additional parameter11 (Test Details: Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Materials in contact with water intended for Human Consumption a)one sample stored at 23(+/-)2 Deg C & b) another sample at60(+/-)2 Deg C for 24 Hours Leaching of Heavy Metals in ppm a)Lead(as Pb) b)Lead(as Pb))	2500.0

454

CUSTOM/TEXTILE/2023 (2023) - CUSTOM/TEXTILE/2023

CUSTOM/TEXTILE/2023

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Blend Composition)	2000.0
2.0 (Tensile Strength)	2000.0
3.0 (Elongation , Weft)	1000.0
4.0 (Tensile Strength, Weft)	2500.0
Firm's request (Average Breaking Strength)	1000.0
Firm's request (Average Extension at Break, Percent)	1000.0

455

R&D as per Customer Specification NTH ER Paint Lab (2023) - R&D as per Customer Specification NTH ER Paint Lab

R&D as per Customer Specification NTH ER Paint Lab

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Heat Resistance Test at 60-65 Deg C)	1200.0
3 (Heat Resistance Test at 85-95 Deg C)	1200.0
2 (Heat Resistance Test at 150-160 Deg C)	1200.0

456

EN 14399 Part-3 (2015) - High-strength structural bolting assemblies for Preloading - Part 3: System HR - Hexagon bolt and nut assemblies

High-strength structural bolting assemblies for Preloading - Part 3: System HR - Hexagon bolt and nut assemblies

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Dimensions of bolts)	2000.0
3.2 & Table 3 (Mechanical Properties of Bolts( Rockwell Hardness Scale- C) as per Clause No.- 7 of ISO 898 (Part-1):2013)	2000.0
3.2 & Table-3 (Mechanical Properties of Bolts( Proof Load) as per Clause No.- 7 of ISO 898 (Part-1):2013)	2000.0
3.2 & Table-3 (Mechanical Properties of Bolts( Ultimate Tensile Load) as per Clause No.- 7 of ISO 898(Part-1):2013)	2000.0
3.2 & Table-3 (Mechanical Properties of Bolts( Tensile Strength) as per Clause No.- 7 of ISO 898(Part-1):2013)	2000.0
3.2 & Table-3 (Chemical Composition of Bolts as per Clause No.- 6 of ISO 898 Part-1:2013)	2000.0
4.1 (Dimensions of nuts)	2000.0
4.2 & Table-5 (Mechanical Properties of Nuts( Rockwell Hardness Scale - C) as per Clause No.- 7 of ISO 898(Part-2):2012)	2000.0
4.2 & Table-5 (Mechanical Properties of Nuts ( Proof Load) as per Clause No.- 7 of ISO 898(Part-2):2012)	3000.0
4.2 & Table-5 (Chemical Composition of Nuts as per Clause No.- 6 of ISO 898 Part-2:2012)	2000.0
3.2 (Charpy Impact Test of Bolt)	5000.0
3.2 (Zinc coating thickness on Bolt as per ISO 10684)	2000.0
4.2 (Zinc coating thickness on Nut as per ISO 10684)	2000.0
3.2 (Depth of Decarburization)	3000.0

457

ILC PAINT SAMPLE (2023) - ILC PAINT SAMPLE

ILC PAINT SAMPLE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying Time , (a) Surface dry IS:101 Part 3 Section 1)	400.0
2 (Drying Time , (b) Hard dry IS:101 Part 3 Section 1)	400.0
3 (Drying Time , (c) Tack Free IS:101 Part 3 Section 1)	400.0
4 (Colour as per IS:5)	400.0
5 (Mass in Kg / Ten Litre as per IS:101 Part-1 Section-7)	1200.0
6 (Scratch Hardness as per IS:101 Part-5 Section-2)	1200.0
7 (Efflux Time (Consistency by flow cup B-4 Ford Cup) IS:101 Part-1 Section-5)	1200.0
8 (Wet Opacity as per IS:101 Part-4 Section-1)	1200.0
9 (Resistance to petrol Benzol Mixture as per IS:101 Part-7 Section-2 (Immersion method))	1200.0
10 (Wet Opacity meter square per liter IS 101 part 4 sec 1 1988 RA 2019)	1000.0
11 (Gloss at 60 IS 101 (Part 4/Sec 4) : 2020)	1000.0
12 (Flexibility and Adhesion IS 101 part 5 sec 2 1988 RA 2019)	1000.0
13 (Resistance to Humidity Under Conditions of Condensation IS 101 part 6 sec 1 1988 RA 2020)	1200.0
14 (Accelerated Storage Stability test (IS 8982))	1200.0
15 (Resistance to Heat IS 101 part 7 sec 3, 2020)	1200.0
16 (Resistance to Warm Water IS 8982)	1200.0
17 (Resistance to Acid IS 2932 2013)	1200.0
18 (Resistance to Alkali IS 2932:2013)	1200.0
19 (Fineness of Grind in micron IS 101 part 3 section 5 ,2019)	1200.0
20 (Finish IS 101 part 3 sec 4,1987 RA 2019)	1200.0
22 (Water Content IS 101 part 2 sec 1 2018)	1200.0
23 (Flash Point(Abel cup) IS 101 part 1 sec 6 ,1987 RA 2019)	1200.0

458

IS 15961 :2025 (2025) - Hot Dip Aluminium-Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)- Specification

Hot Dip Aluminium-Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain)- Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Thickness of Sheet (base metal thickness), mm)	1000.0
3.3 (Coated thickness (total coated thickness), mm)	1000.0
9.1 (Mass of coating (Both sides), g/Sq m)	2000.0
7.1 (Carbon. percent)	500.0
7.1 (Manganese, percent)	500.0
7.1 (Sulphur, percent)	500.0
7.1 (Phosphorous, percent)	500.0
8.3 (Tensile Strength)	1000.0
8.3 (Yield Strength)	1000.0
8.3 (Percent Elongation)	1000.0

459

CUSTOMER SPECIFICATION NTH ER PAINT LAB 2023 (2023) - CUSTOMER SPECIFICATION NTH ER PAINT LAB 2023

CUSTOMER SPECIFICATION NTH ER PAINT LAB 2023

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Appearance)	500.0
2 (Consistency)	1000.0
3 (Density at 30 deg .C gm/cc)	1200.0
4 (Workable time (Pot Life))	1200.0
5 (Cured Film property)	1000.0
6 (Residue on Sieve % by mass a)300 micron sieve)	1000.0
7 (Residue on Sieve % by mass b)150 micron sieve)	1000.0
8 (Residue on Sieve % by mass c)75 micron sieve)	1000.0
9 (Residue on Sieve % by mass d)45 micron sieve)	500.0
10 (Residue on Sieve % by mass e)Pan (below 45 micron))	500.0
11 (Specific Gravity (at dilution Method))	1000.0
12 (Non Volatile Content% by mass)	1500.0
13 (PH)	1000.0
14 (Whiteness Index)	1500.0
15 (Contrast Ratio)	1500.0
16 (Dilution % (Recommended by using Distilled water for Smooth viscous paint suitable for Application))	1000.0

460

AAI SPECIFICATION FOR RUNWAY MARKING PAINT (2023) - SPECIFICATION OF RUNWAY MARKING PAINT (White &Golden yellow

SPECIFICATION OF RUNWAY MARKING PAINT (White &Golden yellow

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Gloss at 45 (before wear))	500.0
2 (Gloss at 45 (After wear400 revolutions ))	2000.0
3 (Opacity before wear Using diffused reflectance measured at an angle of 90)	500.0
4 (Opacity' (after wear. 400 revolutions) Using diffused reflectance measured at an angle of 90)	2500.0
5 (Drying Time in minutes)	1200.0
6 (Residue on 63 microns sieve %)	1200.0
7 (Area coverage on standard Plate (new' surface) (Old surface) sqm/litre)	2000.0
8 (Consistency at 30 deg C(+/-) by Ford cup No B-4)	1500.0
1 (1)	-
9 (Density gm/cc)	1200.0

461

IS 16186 (2014) - Textiles - Light weight jute sacking bags for packing 50 kg foodgrains - Specification

Textiles - Light weight jute sacking bags for packing 50 kg foodgrains - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1(viii) (Oil Content)	2000.0
5.1(vi) (Seam Strength)	1000.0
5.1(v) (Breaking Load,Weftway)	1000.0
5.1(v) (Breaking Load,Warpway)	1000.0
5.1(iv) (Corrected Mass)	1000.0
5.1(iii) (Picks/dm)	1000.0
5.1(ii) (Ends/dm)	1000.0
5.1(i) (Outside Width)	1000.0
5.1(i) (Outside Length)	1000.0
4.3 (Sitches/dm)	1000.0
4 (Construction)	1000.0
Firm's request (Mass)	1000.0

462

Custom - M.S Seamless pipe

M.S Seamless pipe

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Silicon)	1200.0
2 (Nickel)	1200.0
3 (Chromium)	1200.0

463

Surge Suppressor - Surge Suppressor

Surge Suppressor

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test for Cut Off Voltage)	2000.0

464

IS 5192 : Part 1 (1994) - Natural rubber compounds specification: Part 1 for moulded products (Second Revision)

Natural rubber compounds specification: Part 1 for moulded products (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Hardness after Vulcanisation (IRHD))	1000.0
3.3 (Density)	1000.0
3.3 (Tensile Strength (MPa))	2000.0
3.3 (Elongation at Break (%))	1000.0
3.3 (Compression set (%))	2000.0
3.3 (Percentage Change in Tensile Strength after ageing)	2000.0
3.3 (Percentage Change in Elongation after Ageing)	1000.0

465

Custom:PCC - PCC

PCC

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Proportion of aggregate, sand and Cement)	5000.0

466

IS 4835 :1979 RA 2019 (1979 RA2019) - Specification Polyvinyl Acetate Dispersion Based Adhesives for Wood

Specification Polyvinyl Acetate Dispersion Based Adhesives for Wood

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.5.1 (Glue Joint Strength 1 Dry Strength (Appendix E of IS : 851-1978))	5000.0
6.5.2 (6.5.2 Resistance to Micro-Organism,. Mycological Tests)	2000.0
6.6 (Early Strength Development)	2500.0
6.9 (6.9 Temperature of Set -( Appendix F of IS: 851-1978))	2000.0
6.10 (6.10 Resistance to Sustained Load (Annex C))	2000.0
6.1 (Solid Content,% by mass)	2000.0
6.2 (Ash Content,% by mass)	1000.0
6.3 (PH Value)	1000.0
6.4 (Bulk density MASS PER LITRE)	1000.0

467

IS 2720 / 2386 (1983) - Method of Test of Soils (Blanketing Material / Earth / Fill Material)

Method of Test of Soils (Blanketing Material / Earth / Fill Material)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Part 8, Cl 5 & 6 (Determination of Water Content- Dry Density Relation using Heavy Compaction [IS 2720(Part 8)].)	5000.0
Part 16, Cl. 5.2 (Laboratory Determination of CBR [IS 2720 (Part 16)],)	6000.0
Part 4 (Grain Size Analysis [IS 2720 (Part 4)],)	5000.0

468

Navigation Light - Navigation Light

Navigation Light

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Intensity)	15000.0
2 (Colour Coordinates)	5000.0

469

System -3 EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3 (0) - System -3 (F6A +F6A+F6A Total DFT 300 microns) EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3

System -3 (F6A +F6A+F6A Total DFT 300 microns) EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Chemical resistance Test ASTM D 543 10 % NaOH &40 % NaOH for 100 hrs.)	2000.0
2 (Chemical resistance Test ASTM D 543,5 %f H2SO4 for 168 hrs.)	2000.0
3 (Chemical resistance Test ASTM D 543,Acetone for 4 weeks,)	2000.0
4 (Chemical resistance Test , ASTM D 543 Xylene for 4 weeks)	2000.0
5 (Chemical resistance Test, ASTM D 543 Ethanol for 4 weeks)	2000.0
6 (Chemical resistance Test ASTM D 543,Kerosene for 4 weeks)	2000.0
7 (Chemical resistance Test,ASTM D 543 Sea Water 2000 hrs.)	10000.0
8 (100% Humidity Test for 1440 hrs ASTM D 2247)	20000.0

470

System-2 EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3 JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS - System -2 (F15+ F15+ F15. Total DFT 300 microns) EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3 JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

System -2 (F15+ F15+ F15. Total DFT 300 microns) EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3 JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Chemical resistance Test ASTM D 543 10 % NaOH &40 % NaOH for 100 hrs.)	2000.0
2 (Chemical resistance Test ASTM D 543,5 %f H2SO4 for 168 hrs.)	2000.0
3 (Chemical resistance Test ASTM D 543,Acetone for 4 weeks,)	2000.0
4 (Chemical resistance Test , ASTM D 543 Xylene for 4 weeks)	2000.0
5 (Chemical resistance Test, ASTM D 543 Ethanol for 4 weeks)	2000.0
6 (Chemical resistance Test ASTM D 543,Kerosene for 4 weeks)	2000.0
7 (Chemical resistance Test, ASTM D 543 Sea Water 2000 hrs.)	10000.0
8 (Immersion in DM/DI water @90deg.C (ASTM C868) for 30 days)	2500.0
9 (100% Humidity Test for 1440 hrs (ASTM D2247))	20000.0
10 (Thermal Shock Resistance Test; 5 cycles @ 30 minutes in furnace at 120 0 C and 15 minutes in water after quenching in water for each cycle. (ASTM D2485 method A))	3000.0
11 (Cathodic Disbondment Test at 60 deg.C (ASTM G8))	2500.0

471

System-1 EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3 - System -1 (F9 + P6+ F6B + F2. Total DFT 345 microns) EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3 JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

System -1 (F9 + P6+ F6B + F2. Total DFT 345 microns) EIL SPECIFICATION NO B 329-100-02-42-PCS-0001 REV 3 JOB SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATINGS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Cyclic Test ( Duration 4200 hours) : Salt Spray72 hrs. Drying in air: 16 hrs. UV-A340 nm weather meter: 80 hrs. One cycle: 168 hrs. (25 cycles at 168 hrs. each cycle) (ASTM D5894))	175000.0

472

NTH PAINT 2023 Epoxy phenolic coating system (2023) - Epoxy phenolic coating system Finish coat of two-pack aliphatic isocyanate-cured acrylic finish paint

Epoxy phenolic coating system Finish coat of two-pack aliphatic isocyanate-cured acrylic finish paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (QUV exposure ( ASTM D 4587) - 1000 hrs)	50000.0
2 (Gloss value at 60 degree angle (Before QUV Exposure))	1200.0
3 (Gloss value at 60 degree angle (after 1000 hours of QUV Exposure))	1200.0
4 (Solid by volume % by mass)	2000.0
5 (colour change delta E value Before QUV Exposure)	2000.0
6 (colour change delta E value after 1000 hours QUV Exposure)	2000.0

473

LED Flexible Strip ( IOCL) - Test of LED Flexible Strip As per IOCL Technical Requirements

Test of LED Flexible Strip As per IOCL Technical Requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Maximum Power Per RM of LED Strip)	2000.0
3 (LEDs Per Meter)	1000.0
6 (Size of Flexible Strip)	2000.0
7 (Operating Voltage 24 Volt DC)	2000.0
8 (CCT of LED Strip)	5000.0
11 (CRI of LED Strip, >70)	5000.0
15 (IP-6X ( Dust Protected))	6000.0
15(i) (Temporary Water Immersion Test IP-X7)	6000.0
18 (Glow wire Test)	2000.0
10 (Efficacy of LED Strip >95 Lm/W)	5000.0

474

Indian Oil 0.9W LED Module - Technical Specification of Indian Oil 0.9W LED Module

Technical Specification of Indian Oil 0.9W LED Module

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Wattage of 0.9 Watt LED Module (LM 79))	2000.0
4 (Operating Voltage of LED Module)	2000.0
5 (Operation at -30 Deg C)	5000.0
5(i) (Operation at +50 Deg C)	5000.0
6 (CCT of LED Module Supporting Documents(LM 79))	5000.0
8 (Efficacy Of LED Module( supporting Documents LM 79))	5000.0
14 (IP 6X Test for Dust Protected as per IS/IEC 60529)	6000.0
14(i) (IP X7 protection against the effect of Temporary immersion in water)	6000.0
15 (Dimension of LED Module Width - Max 15 mm, Max.Thickness -8.5 mm, Standard Length-66 mm+/-10%)	2000.0
18 (Glow Wire Test)	2000.0
2.1 (Wattage of LED Module 0.9 Watt ( LM 79) (with out Driver rated voltage 12 Volt DC))	2000.0
15.1 (Dimension of LED Module Width, Thickness,Standard Length .)	2000.0

475

10322 Part 5 /Sec 7 : 2017 (2017) - Lighting Chains

Lighting Chains

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
20.6 (Lighting Chain Marking)	500.0
20.7 (Construction test as per Specification)	1200.0
20.8 (Clause 20.8, Creepage Distances & Clearances)	1200.0
20.10 (Terminals)	1200.0
20.11 (External and Internal Wiring)	1200.0
20.12 (Protection against Electric Shock)	1200.0
20.13 (Endurance Tests and thermal test)	5500.0
20.14 (Resistance to dust, solid objects and Moisture)	12000.0
20.15 (Insulation Resistance and Electric Strength)	5000.0
20.16 (Resistance to Heat)	2000.0
20.16 (Resistance to fire)	5000.0
20.16 (Resistance to tracking)	5000.0

476

IS 5986 (2017) - Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2.2 (Bend Test)	1500.0

477

ND Custom 7 (2023) - Sample of B-150 type OHE traction mast (Galvanized fabricated structure)

Sample of B-150 type OHE traction mast (Galvanized fabricated structure)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Mass of Zinc Coating as per IS 6745)	2000.0
2 (Zn Coating Thickness as per IS:3203 (1982))	2000.0

478

RDSO 153 (2011) - RDSO/SPN/153/2011 REVISION 4.1 (FOR LED SIGNAL LIGHTING UNIT)

RDSO/SPN/153/2011 REVISION 4.1 (FOR LED SIGNAL LIGHTING UNIT)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.1.(ii) (Colour Co- Ordinates, Clause 9.1.(ii))	5000.0
Clause 5.2, 7.3 (Operating parameters ,Clause 5.2, 7.3 of RSDO/SPN/153/2011, Rev 4.1)	5000.0
Clause 9.1 (vii) (Climatic Test Change in Temperature , Clause 9.1 (vii))	10000.0
Clause 9.1 (vii) (Climatic Test (Dry Heat Test) as per RDSO/SPN/153/2011, Rev 4.1)	10000.0
,Clause 9.1 (vii) (Climatic ( Cold Test),Clause 9.1 (vii) as per RDSO/SPN/153/2011, REV- 4.1)	10000.0
Clause 9.1 (vii) (Climatic ( Damp Heat Test Cyclic) ,Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	10000.0
Clause 9.1 (vii) (Climatic Test ( Damp Heat Steady State) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	25000.0
Clause 9.1 (vii) (Climatic Test ( Salt Mist) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	10000.0
Clause 9.1 (vii) (Climatic Test ( Dust Test) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	7500.0
Clause 9.1 (vii) (Climatic Test ( Water Immersion Test) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	7500.0
Clause 9.1 (vii) (Climatic Test ( Driving Rain) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	5000.0
Clause 9.1 (vii) (Climatic Test ( Shock Test ) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	10000.0
Clause 9.1 (vii) (Climatic Test ( Vibration Test ) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	15000.0
Clause 9.1 (vii) (Climatic Test (Thermal Cycling)Clause 9.1 (vii) of RDSO/SPN/153/2011 Rev 4.1)	10000.0
Clause 9.1(xii) (Applied High Voltage Test ,Clause 9.1(xii) of RDSO/SPN/153/2011, Rev 4.1)	3000.0
,Clause 9.1(xiii) (Insulation resistance Test ,Clause 9.1(xiii) of RDSO/SPN/153/2011, Rev 4.1)	2000.0
Clause 9.1(xiv) (Minimum Lighting Voltage ,Clause 9.1(xiv) of RDSO/SPN/153/2011, Rev 4.1)	2000.0

479

RDSO Standard STR No. C-8217 (Rev-1) - SCHEDULE Of" REQUIREMENTS FOR ALUMINIUM CHEQUERED SHEETS FOR USE AS FLOORING MATERIAL ON COACHING STOCK" (SUPERSEDES C-8217) .

SCHEDULE Of" REQUIREMENTS FOR ALUMINIUM CHEQUERED SHEETS FOR USE AS FLOORING MATERIAL ON COACHING STOCK" (SUPERSEDES C-8217) .

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Dimension)	1000.0
7.2 (Tensile Strength)	2000.0
7.2 (0.2% Proof stress)	1000.0
7.2 (Elongation)	1000.0
7.2 (Bend Test)	1500.0
4.1.2 (Chemical Composition of the material shall be as per IS 737:1986, Designation 65032)	4500.0

480

CUSTOM/ILPT/2023 - CUSTOM/ILPT/2023

CUSTOM/ILPT/2023

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Full Belt Breaking Force(Warp))	-
2.0 (Full Belt Elongation at Break)	1000.0
3.0 (Full Belt Elongation at Ref. load(10 % FB))	-
4.0 (Full Belt Breaking Force(Weft))	-