NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1252 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

421

Custom/BC/BM - Bitumen Content BC/BM

Bitumen Content BC/BM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Bitumen content BC/BM)	3000.0

422

Custom - Bitumen binder

Bitumen binder

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Bitumen content in DBM)	3000.0

423

CUSTOMER SPECIFICATION FIRE RETARDANTCEMENT /PUTTY (2023) - CUSTOMER SPECIFICATION FIRE RETARDANTCEMENT /PUTTY

CUSTOMER SPECIFICATION FIRE RETARDANTCEMENT /PUTTY

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Appearance &Colour)	200.0
3 (Density As per IS std)	1000.0
4 (Fire test on metal surface for 02 Hours)	5000.0
5 (Surface spread of Flame test Bs 476 part 7)	5000.0
6 (Temperature resistance test 650 deg C ASTM D 2485)	2500.0
7 (Salt spray test for 96 hours ASTM B 117)	4800.0

424

Custom-34-NTH-LM - W-Beam Metal Crash Barrier

W-Beam Metal Crash Barrier

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Tensile Strength)	2000.0
2 (Yield stress)	1000.0
3 (Elongation)	1000.0
4 (Mass per Metre)	1500.0
5 (Bend Test)	1000.0
6 (Carbon)	500.0
7 (Sulphur)	500.0
8 (Phosphorus)	500.0
9 (Manganese)	500.0
10 (Carbon Equivalent)	500.0

425

ELRS /SPEC/ SI /0015 (2001) - SPECIFICATION FOR RELIABILITY OF ELECTRONICS USED IN ROLLING STOCK APPLICATION

SPECIFICATION FOR RELIABILITY OF ELECTRONICS USED IN ROLLING STOCK APPLICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.7 & Annexure-1 (Burn – in test)	20000.0

426

IS 6745 (1972) - Mass of Zinc Coating (IS 6745)

Mass of Zinc Coating (IS 6745)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Mass of Zinc Coating (IS 6745:1972))	1000.0

427

NTH ER PAINT LAB CUSTOMER SPECIFICATION 2023 (2023) - NTH ER PAINT LAB CUSTOMER SPECIFICATION 2023

NTH ER PAINT LAB CUSTOMER SPECIFICATION 2023

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Acid value %)	1200.0
2 (Wet Opacity/Coverage capacity Minimum & Maximum(as per IS 101))	1500.0
3 (Drying Time at 30 Deg C a) Surface Dry b) Hard Dry as per IS 101)	1200.0
4 (Mass in Kg/10 litre as per IS 101)	1200.0
5 (Salt spray Test 5 % NAcl solution for 100 hours ASTM B 117)	5000.0
6 (Abrasion Resistance Test ASTM D 4060)	3500.0
7 (Density gm/cc IS 101 part1 Sec 7)	1200.0
8 (Solid content % IS 101 part8 Sec 2)	1200.0
10 (PH at 25 Deg C)	500.0
12 (2000 hrs QUV)	100000.0

428

CUSTOM-25-ER-MCALI - Calibration of Floating Carriage Micrometer

Calibration of Floating Carriage Micrometer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Length)	2400.0

429

IS 16172 (2023) - Reinforcement couplers for mechanical splices of bars in concrete - Specification

Reinforcement couplers for mechanical splices of bars in concrete - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Visual Observation (Workmanship and Finish))	1000.0
8 (Chemical composition, % by mass)	3000.0
9.2 (Tensile Strength as per IS 1608(Part 1):2022)	1500.0
9.2 (Percentage Elongation as per IS 1608(Part 1):2022)	1500.0
9.2 (Visual Observation for Nature & Location of failure of spliced specimen (With Coupling).)	1000.0
0 (Test results as per customer test request.)	15000.0
9.2.1 (The tensile strength of the spliced bar ( With Coupling))	2500.0
9.2.2 (The minimum percentage elongation at maximum force (also termed as uniform elongation) for spliced bar ( with coupler) when measured in accordance with the method given in Annex B in the reinforcing bar outside the length of the mechanical splice before failure.)	1000.0
9.2.2 (The percentage elongation at maximum force for unspliced specimen)	1000.0

430

CUSTOM-24-ER-MCALI (2023) - Calibration of Profile Projector

Calibration of Profile Projector

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Magnification)	2000.0
2 (Angle)	2000.0
3 (Length)	2000.0
4 (Length)	2000.0

431

IS 9857:1990 (1990) - Welding Cable Specification

Welding Cable Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1.a.2 (Test on Conductor- Conductor Resistance Test)	2500.0
10.1.b (Test for thickness of Covering)	1500.0
10.1.d (High Voltage Test (Water Immersion Test))	3500.0

432

RDSO SPECIFICATION No. M&C/ PCN/ 100/ 2018 (2018) - SPECIFICATION FOR EPOXY CUM POLYURETHANE PAINTING SYSTEM (TWO PACK) FOR THE EXTERIOR PAINTING OF RAILWAY COACHES, DIESEL AND ELECTRIC LOCOMOTIVES AND OTHER INDUSTRIAL APPLICATIONS

SPECIFICATION FOR EPOXY CUM POLYURETHANE PAINTING SYSTEM (TWO PACK) FOR THE EXTERIOR PAINTING OF RAILWAY COACHES, DIESEL AND ELECTRIC LOCOMOTIVES AND OTHER INDUSTRIAL APPLICATIONS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
APPENDIX –VII METHOD OF IDENTIFYING AROMATIC AND ALIPHATIC ISOCYANATE (Identification of poly isocyanate ( aliphatic or aromatic in nature) procedure in Appendix- VII. Specification No M&C /PCN/100/2018)	3000.0

433

IS 4984 (2016) - Polyethylene pipes for water supply - Specification (Fifth Revision)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.6 (Overall Migration (Chemical Lab))	2000.0
8.4 (Melt Flow Rate at 190 degree celcius and 5kgf)	2000.0
8.2 (Longitudinal Reversion Test)	2000.0
7.4 (Wall Thickness)	500.0
7.2 (Length)	1000.0
7.1 (Visual Appearance)	500.0
6.2 (Colour)	-
8.3 (Carbon Black Dispersion)	1000.0
7.4.1 (Outside Diameter)	500.0
7.4.1.2 (Ovality)	100.0
6.2.1 (Colour Of strip)	-
6.2.1 (Width Of Strip)	100.0
Firm's request (Hardness(Shore D))	1000.0
firm's request (Density)	2000.0

434

Custom-33-ER-LM - Load Test

Load Test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Load Test)	15000.0

435

Custom - Raw Water (NMDC) (Vide Annexure)

Raw Water (NMDC) (Vide Annexure)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Chemical Parameters Vide Annexure)	12000.0

436

CUSTOM/TEXTILE/2024 - CUSTOM/TEXTILE/2024

CUSTOM/TEXTILE/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Average GSM)	1000.0
2.0 (Thread per inch (Warp))	500.0
3.0 (Threads per inch (Weft))	500.0
4.0 (Yarn Count (warp))	1000.0
5.0 (Yarn Count (Weft))	1000.0
6.0 (Blend Composition %)	2000.0
7.0 (Colour Fastness to Washing)	2000.0
8.0 (Type of Weave)	500.0
9.0 (pH)	1000.0
10 (Tensile Strength)	2000.0

437

Valve protective coating on Ductile Cast Iron (as per BS 2789 Gr 420/12 or 500/7) (2023) - Valve protective coating on Ductile Cast Iron (as per BS 2789 Gr 420/12 or 500/7)

Valve protective coating on Ductile Cast Iron (as per BS 2789 Gr 420/12 or 500/7)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Coating dry film thickness (DFT) for flat surface Cl 5.3.1 of DIN 30677- Part 1)	1000.0
2 (Coating dry film thickness (DFT) for convex surface Cl 5.3.21 of DIN 30677 Part 1)	1000.0
3 (Cyclic Salt Spray Test (for 24 hours) ASTM B 117)	6000.0
4 (Cycle Artificial Weathering Test 100% Humidity (for 24 hours ASTM D 2247 10 Cycles)	6500.0
5 (Cathodic Disbondment Test (for evaluation of any pitting development) For 30 days at 23 ± 2° C ASTM G-95)	7500.0
6 (Cathodic Disbondment Test (for evaluation of any pitting development) For 2 days at 65 ± 2° C ASTM G-95)	1500.0
7 (Bond Strength Cl 4.2.2 of DIN 30677 Part 1 – Feb 1991)	2500.0

438

IS 7933 (1975) - Specification for flexible polyurethane foam for domestic mattresses

Specification for flexible polyurethane foam for domestic mattresses

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.8 (Density)	1000.0

439

IS 101 ( Part 3/Set 2 ) (:1989 (RA 2019)) - METHODS OF SAMPLING AND TEST FOR PAINTS,VARNISHESAND RELATED PRODUCTS (PART 3: TESTS ON PAINT FILM FORMATION) (Section 2: Film Thickness)

METHODS OF SAMPLING AND TEST FOR PAINTS,VARNISHESAND RELATED PRODUCTS (PART 3: TESTS ON PAINT FILM FORMATION) (Section 2: Film Thickness)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Measurement of dry film thickness on magnetic metallic substrate by magnetic flux principle)	2000.0

440

BIS IS 2932:2013 RA 2018 (2013) - Enamel, Synthetic, Exterior : (a) Undercoating (b) Finishing - Specification :for Domestic and Decorative Applications

Enamel, Synthetic, Exterior : (a) Undercoating (b) Finishing - Specification :for Domestic and Decorative Applications

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 Composition (Composition 6.1.1 Rosin and Resin derivative test IS 101 (Part 9/Sec 2)))	100.0
6.1.2 (Total Non-Volatile Content( matter including pigments, extenders and vehicles) IS 101 (Part8/Sec 2))	500.0
6.2 (Condition in Container)	100.0
6.3 (Freedom from Coarse Particles IS 101 (Part l/Sec 2))	100.0
6.4 (Skin Formation IS 101(Part 1/Sec 2).)	100.0
6.5 (Thinning Properties)	100.0
6.6 (Application Properties)	100.0
6.7 (Durability 6.7.1 Registered Sample NORMAL OUTDOOR EXPOSURE TEST ANNEX C at an angle of 45° facing south. Commence the exposure not earlier than the third week of January and not later than the first week of April. (Clauses 6.7.1 .1, 6.7.1.2, 6.7.2.2 and 8.1.1.1))	10000.0
6.7.1.2 (6.7 Durability 6.7.1.2 sample for registration C-4 Artificial weathering apparatus(Xenon ) for 700 hours)	10000.0
6.7.1.3 (Durability Accelerated weathering apparatus (QUV) for 360 hours 6.7.1.3 Lamp type : UV 313 Test cycle : UV (4 h at 60 ± 3°C) Condensation (4 h at 50 ± 3°C)Irradiance : 0.67 W/m2/nm UVB wavelength : 295 – 325 nm (Approx))	10000.0
6.8 (Lead Restriction IS 101 (Part 8/Sec 5))	500.0
6.9 Table 2 1 a) (Consistency Annexure B)	100.0
6.9 Table 2 1 b) (Viscosity by ford cup No. 4 at 27 ± 2°C IS (Part l/Sec 5) —)	100.0
6.9 Table 2 ii (Mass, in kg/10 litre IS 101 (Part l/Sec 7))	100.0
6.9 Table 2 iii a) (Drying time in hours a) Surface Dry)	100.0
6.9 Table 2 iii b) (Drying Time b) Hard Dry in hours)	100.0
6.9 Table 2 iii C) (Drying Time in hours c)Tack free)	100.0
6.9 Table 2 iv a) (Finish IS 101 (Part 3/Sec 4))	100.0
6.9 Table 2 iv b) (b) Gloss at 60 Deg Angle IS 101(Part 4/Sec 4))	100.0
6.9 Table 2 vi (Colour IS 101 (Part 4/Sec 2))	100.0
6.9 Table 2 vi a) (Flexibility and adhesion: a) Scratch hardness IS 101 (Part 5/Sec 2) cl 2)	100.0
6.9 Table 2 vii b) (b) Bend test (with 6.25 mm in type 1 apparatus) Clause 2 of IS 101 (Part 5/Sec 2))	200.0
6.9 Table 2 viii (Flash point in Deg.C IS 101 (Part l/Sec 6))	200.0
6.9 Table 2 ix a) (Composition a) Volume solids percent IS 101 (Part 8/Sec 6))	200.0
6.9 Table 2 ix b) (Composition b)Phthalic anhydride content non-volatile vehicle, percent by mass, IS 101 (Part 8/Sec 4))	200.0
6.9 Table 2 x (Resistance to acid Annexure E)	200.0
6.9 Table 2 xi) (Resistance to alkali Annexure F)	200.0
6.9 Table 2 xiii (Keeping properties For 12 Months IS 101 (Part 6/Sec 2) Not less than one year from date of manufacturing)	5000.0
6.9 Table 2 xiv (Wet opacity, m2/10 litre As per values given in clause 5 IS 101 (Part 4/Sec 1))	100.0

441

CUSTOM - Ferro Alloy

Ferro Alloy

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon)	1000.0
2 (Sulphur)	1000.0
3 (Phosphorus)	1000.0
4 (Silicon)	1000.0
5 (Chromium)	1000.0
6 (Manganese)	1000.0
7 (Aluminium, % by mass)	1200.0

442

Distilled water/Reagent water for Laboratory use (-) - Distilled water/Reagent water for Laboratory use

Distilled water/Reagent water for Laboratory use

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Electrical Conductivity micro siemens/cm at 25 deg C)	1000.0
2 (PH at 25 Deg C)	1000.0
3 (Sodium in ppm)	1000.0
4 (Chloride ppm)	1000.0

443

IS 278 (2009) - Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.1 (Breaking Load of Completed Barbed Wire)	1000.0
12.1 (Tensile Strength of Line Wire)	1000.0
12.3 (Ductility)	1000.0
12.2.1 (Zinc Coating of Line wire)	2000.0
6 (Chemical composition (Carbon))	625.0
5 (Dimension/ Sizes)	1000.0
9 (Freedom from Defects)	500.0
6 (Chemical composition (Manganese))	625.0
6 (Chemical composition (Sulphur))	625.0
6 (Chemical composition (Phosphorus))	625.0
12.2.2 (Zinc Coating of Point wire)	2000.0
12.2.2 (Adhesion of Coating of Point wire)	1000.0
12.2.1 (Adhesion of Coating of Line wire)	1000.0

444

CUSTOM/PP ROPE/2023 - CUSTOM/PP ROPE/2023

CUSTOM/PP ROPE/2023

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Dia of Rope)	500.0
2.0 (Weight of Rope)	1000.0
3.0 (Breaking Strength of Individual Rope)	5000.0
4.0 (Size of Crate)	1000.0
5.0 (Size of Mesh Opening)	500.0
6.0 (Structure of Rope)	500.0
7.0 (Construction of Net)	500.0
8.0 (Size of Gabion)	500.0
9.0 (Linear Density of Rope)	1000.0
10.0 (Material of Rope)	5000.0
11 (Length of Lay)	1000.0
12 (Weight of Tar)	1200.0

445

IS 4759 (1996) - Hot - Dip zinc coatings on structural steel and other allied products - Specification (Third Revision)

Hot - Dip zinc coatings on structural steel and other allied products - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 (Mass of Zinc Coating, (g/m2))	2000.0
9.3 (Determination of Uniformity of Galvanizing Coating)	1000.0

446

RDSO/2009/CG-03 (2016) - Schedule of Technical Requirements for Injection Moulded Polyacetal Protective Tube for ICF Type B.G. Main Line & EMU Trailer Coaches (Tentative).

Schedule of Technical Requirements for Injection Moulded Polyacetal Protective Tube for ICF Type B.G. Main Line & EMU Trailer Coaches (Tentative).

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Specific Gravity)	1000.0
5.1 (Tensile Strength)	2000.0
5.1 (Elongation at Break)	1000.0
5.1 (Melt Flow Rate @ 190 deg.C at 2.16 kg load)	2000.0

447

IS 613 (2000) - Copper Rods and Bars for Electrical Purposes

Copper Rods and Bars for Electrical Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.4 (Resistance of a Solid Conductor)	5000.0
6 (Freedom from defects)	1000.0
9.1 (Tensile Strength)	2000.0
9.1 (Elongation)	1000.0
9 (Vickers Hardness)	2000.0
9.2 (Bend Test)	1000.0
10 (Dimensions)	1000.0
11 (Electrical Resistivity Test)	2000.0
8 (Chemical composition as given in for grades ETP, FRHC of IS 191 (Part 5) or IS 191 (Part 6) respectively.)	5000.0

448

CUSTOM - Iron content in Mild Steel

Iron content in Mild Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Iron content)	2000.0

449

ND Custom 9 (2023) - Training on Manual Metal Arc welding/ Gas Metal arc Welding

Training on Manual Metal Arc welding/ Gas Metal arc Welding

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (One Day Training Programme on MMAW/GMAW)	1000.0
2 (Two Days Training Programme on MMAW/GMAW)	1000.0
3 (Three Days Training Programme on MMAW/GMAW)	3000.0
4 (Four Days Training Programme on MMAW/GMAW)	4000.0
5 (Five Days Training Programme on MMAW/GMAW)	5000.0

450

IS 5154-Part 1- 2013 (2013) - LEAD-ACID TRACTION BATTERIES PART 1 GENERAL REQUIREMENTS AND METHODS OF TEST [ Bag plate Lead Acid Secondary Battery)

LEAD-ACID TRACTION BATTERIES PART 1 GENERAL REQUIREMENTS AND METHODS OF TEST [ Bag plate Lead Acid Secondary Battery)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Capacity Test on the lines of IS 5154 - Part 1 Sample shall meets the requirements ,Ca = 0,85 CN at the first cycle; Ca = 1,00 CN at or before the tenth cycle. Charging Current . Specific Gravity and Cut off Voltage as per Manufacturer instruction)	20000.0
6.1 (Energy Density Test)	5000.0