NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1226 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

511

NTH PAINT 2023 Epoxy phenolic coating system (2023) - Epoxy phenolic coating system Finish coat of two-pack aliphatic isocyanate-cured acrylic finish paint

Epoxy phenolic coating system Finish coat of two-pack aliphatic isocyanate-cured acrylic finish paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (QUV exposure ( ASTM D 4587) - 1000 hrs)	50000.0
2 (Gloss value at 60 degree angle (Before QUV Exposure))	1200.0
3 (Gloss value at 60 degree angle (after 1000 hours of QUV Exposure))	1200.0
4 (Solid by volume % by mass)	2000.0
5 (colour change delta E value Before QUV Exposure)	2000.0
6 (colour change delta E value after 1000 hours QUV Exposure)	2000.0

512

LED Flexible Strip ( IOCL) - Test of LED Flexible Strip As per IOCL Technical Requirements

Test of LED Flexible Strip As per IOCL Technical Requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Maximum Power Per RM of LED Strip)	2000.0
3 (LEDs Per Meter)	1000.0
6 (Size of Flexible Strip)	2000.0
7 (Operating Voltage 24 Volt DC)	2000.0
8 (CCT of LED Strip)	5000.0
11 (CRI of LED Strip, >70)	5000.0
15 (IP-6X ( Dust Protected))	6000.0
15(i) (Temporary Water Immersion Test IP-X7)	6000.0
18 (Glow wire Test)	2000.0
10 (Efficacy of LED Strip >95 Lm/W)	5000.0

513

Indian Oil 0.9W LED Module - Technical Specification of Indian Oil 0.9W LED Module

Technical Specification of Indian Oil 0.9W LED Module

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Wattage of 0.9 Watt LED Module (LM 79))	2000.0
4 (Operating Voltage of LED Module)	2000.0
5 (Operation at -30 Deg C)	5000.0
5(i) (Operation at +50 Deg C)	5000.0
6 (CCT of LED Module Supporting Documents(LM 79))	5000.0
8 (Efficacy Of LED Module( supporting Documents LM 79))	5000.0
14 (IP 6X Test for Dust Protected as per IS/IEC 60529)	6000.0
14(i) (IP X7 protection against the effect of Temporary immersion in water)	6000.0
15 (Dimension of LED Module Width - Max 15 mm, Max.Thickness -8.5 mm, Standard Length-66 mm+/-10%)	2000.0
18 (Glow Wire Test)	2000.0
2.1 (Wattage of LED Module 0.9 Watt ( LM 79) (with out Driver rated voltage 12 Volt DC))	2000.0
15.1 (Dimension of LED Module Width, Thickness,Standard Length .)	2000.0

514

10322 Part 5 /Sec 7 : 2017 (2017) - Lighting Chains

Lighting Chains

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
20.6 (Lighting Chain Marking)	500.0
20.7 (Construction test as per Specification)	1200.0
20.8 (Clause 20.8, Creepage Distances & Clearances)	1200.0
20.10 (Terminals)	1200.0
20.11 (External and Internal Wiring)	1200.0
20.12 (Protection against Electric Shock)	1200.0
20.13 (Endurance Tests and thermal test)	5500.0
20.14 (Resistance to dust, solid objects and Moisture)	12000.0
20.15 (Insulation Resistance and Electric Strength)	5000.0
20.16 (Resistance to Heat)	2000.0
20.16 (Resistance to fire)	5000.0
20.16 (Resistance to tracking)	5000.0

515

IS 5986 (2017) - Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2.2 (Bend Test)	1500.0

516

ND Custom 7 (2023) - Sample of B-150 type OHE traction mast (Galvanized fabricated structure)

Sample of B-150 type OHE traction mast (Galvanized fabricated structure)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Mass of Zinc Coating as per IS 6745)	2000.0
2 (Zn Coating Thickness as per IS:3203 (1982))	2000.0

517

RDSO 153 (2011) - RDSO/SPN/153/2011 REVISION 4.1 (FOR LED SIGNAL LIGHTING UNIT)

RDSO/SPN/153/2011 REVISION 4.1 (FOR LED SIGNAL LIGHTING UNIT)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.1.(ii) (Colour Co- Ordinates, Clause 9.1.(ii))	5000.0
Clause 5.2, 7.3 (Operating parameters ,Clause 5.2, 7.3 of RSDO/SPN/153/2011, Rev 4.1)	5000.0
Clause 9.1 (vii) (Climatic Test Change in Temperature , Clause 9.1 (vii))	10000.0
Clause 9.1 (vii) (Climatic Test (Dry Heat Test) as per RDSO/SPN/153/2011, Rev 4.1)	10000.0
,Clause 9.1 (vii) (Climatic ( Cold Test),Clause 9.1 (vii) as per RDSO/SPN/153/2011, REV- 4.1)	10000.0
Clause 9.1 (vii) (Climatic ( Damp Heat Test Cyclic) ,Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	10000.0
Clause 9.1 (vii) (Climatic Test ( Damp Heat Steady State) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	25000.0
Clause 9.1 (vii) (Climatic Test ( Salt Mist) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	10000.0
Clause 9.1 (vii) (Climatic Test ( Dust Test) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	7500.0
Clause 9.1 (vii) (Climatic Test ( Water Immersion Test) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	7500.0
Clause 9.1 (vii) (Climatic Test ( Driving Rain) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	5000.0
Clause 9.1 (vii) (Climatic Test ( Shock Test ) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	10000.0
Clause 9.1 (vii) (Climatic Test ( Vibration Test ) , Clause 9.1 (vii) as per RDSO/SPN/153/2011, Rev 4.1)	15000.0
Clause 9.1 (vii) (Climatic Test (Thermal Cycling)Clause 9.1 (vii) of RDSO/SPN/153/2011 Rev 4.1)	10000.0
Clause 9.1(xii) (Applied High Voltage Test ,Clause 9.1(xii) of RDSO/SPN/153/2011, Rev 4.1)	3000.0
,Clause 9.1(xiii) (Insulation resistance Test ,Clause 9.1(xiii) of RDSO/SPN/153/2011, Rev 4.1)	2000.0
Clause 9.1(xiv) (Minimum Lighting Voltage ,Clause 9.1(xiv) of RDSO/SPN/153/2011, Rev 4.1)	2000.0

518

RDSO Standard STR No. C-8217 (Rev-1) - SCHEDULE Of" REQUIREMENTS FOR ALUMINIUM CHEQUERED SHEETS FOR USE AS FLOORING MATERIAL ON COACHING STOCK" (SUPERSEDES C-8217) .

SCHEDULE Of" REQUIREMENTS FOR ALUMINIUM CHEQUERED SHEETS FOR USE AS FLOORING MATERIAL ON COACHING STOCK" (SUPERSEDES C-8217) .

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Dimension)	1000.0
7.2 (Tensile Strength)	2000.0
7.2 (0.2% Proof stress)	1000.0
7.2 (Elongation)	1000.0
7.2 (Bend Test)	1500.0
4.1.2 (Chemical Composition of the material shall be as per IS 737:1986, Designation 65032)	4500.0

519

CUSTOM/ILPT/2023 - CUSTOM/ILPT/2023

CUSTOM/ILPT/2023

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Full Belt Breaking Force(Warp))	-
2.0 (Full Belt Elongation at Break)	1000.0
3.0 (Full Belt Elongation at Ref. load(10 % FB))	-
4.0 (Full Belt Breaking Force(Weft))	-

520

CUSTOM - LOW SULPHUR HAVVY STOCK OIL

LOW SULPHUR HAVVY STOCK OIL

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (POUR POINT)	1200.0
2 (DENSITY AT 15 Dg C)	1200.0
3 (KINEMATIC VISCOCITY)	1200.0

521

Custom - Purity of Silicon

Purity of Silicon

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Purity of Silicon)	2000.0

522

RDSO/SPN/176/2013 (2014) - MULTI SECTION DIGITAL AXLE COUNTER

MULTI SECTION DIGITAL AXLE COUNTER

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.5.5.1 (Change of Temperature Test)	15000.0
11.5.5.2 (Dry Heat test)	10000.0
11.5.5.3 (Cold test)	10000.0
11.5.5.4 (Damp Heat Test (Cyclic))	35000.0
11.5.5.5 (Damp Heat Test (Steady state))	25000.0
11.5.8 (Vibration Test)	15000.0
11.5.5.6 (Salt Mist Test)	5000.0
11.5.5.7 (Driving Rain Test)	15000.0
11.5.5.8 (Water Immersion Test)	15000.0
11.5.5.9 (Dust Test)	15000.0
11.5.4 (Insulation Resistance Test)	18000.0
11.5.3 (Applied High Voltage Test)	2000.0

523

Custom - Testing of DBM ,BM & BC for Bitumen content

Testing of DBM ,BM & BC for Bitumen content

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Bitumen Content in DBM)	3000.0
2 (Bitumen Content in BC/BM)	3000.0

524

3328:1993 - QUALITYTOLERANCES FOR WATER FOR SWIMMING POOLS

QUALITYTOLERANCES FOR WATER FOR SWIMMING POOLS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (pH value)	1200.0
2 (Total Alkalinity (as CaCO3) mg/l)	1200.0
3 (Aluminium (as Al) mg/l)	1200.0
6 (Total Dissolved Solids, mg/l)	1200.0
7 (Chloride (as Cl))	1200.0
8 (Iron)	1200.0
9 (Heavy metals (as Pb))	1200.0
10 (Colour , Hazen Units)	1200.0
11 (Turbidity, NTU)	1200.0
12 (Odour)	1200.0
13 (Taste)	1200.0
3.3.2 (Coliform Organisms)	1200.0

525

RDSO/SPN/176/2013 Ver 3.0 date Effective 31.03.2014 (2014) - Specification for Multi Section Digital Axle Counter

Specification for Multi Section Digital Axle Counter

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.5.5.1 (Change of temperature test as per , clause 11.5.5.1 of RDSO/SPN/176/2013 Version 3)	12000.0
11.5.5.2 (Dry Heat Test as per IS 9000/Pt-III, Sec-5, clause 11.5.5.2 of RDSO/SPN/176/2013 Version 3)	12000.0
11.5.5.3 (Cold Test as per IS 9000/Pt-II, Sec- 3, clause 11.5.5.3 of RDSO/SPN/176/2013 Version 3)	15000.0
11.5.5.4 (Damp Heat Test (Cyclic) as per IS 9000/Pt-V, , Sec 2 ,Clause 11.5.5.4 of RDSO/SPN/176/2013 Version 3)	20000.0
11.5.5.5 (Damp Heat Test (Steady State) as per IS 9000/Pt-IV, Clause 11.5.5.5 of RDSO/SPN/176/2013 Version 3)	27000.0
11.5.8 (Vibration Test As per IS 9000( Part VIII) Clause 11.5.8 of RDSO/SPN/176/2013 Version 3)	15000.0
11.5.5.6 (Salt Mist Test, Clause 11.5.5.6, Test as per RDSO/SPN/144)	15000.0
11.5.5.7 (Driving Rain Test ( For Axial Detector), Clause 11.5.5.7 of IS 9000 PT XVI Shall Comply the requirements of IP-66)	10000.0
11.5.5.8 (Water Immersion Test ( For Axial Detectors) clause 11.5.5.8 of RDSO/SPN/176/2013 and test as per IS : 9000, PT-XV/Section 7 shall comply the requirements of IP-68 After the test, sample shall be measure insulation resistance shall not be less than 10 Mega Ohms.)	10000.0
11.5.5.9 of RDSO/SPN/176/2013, Version -3.0 (Dust Test as per IS : 9000, Part-XII. and requirement shall comply IP-60)	15000.0
11.5.5.5 (Damp Heat Test(Steady State) as per IS : 9000/PT-IV and Clause 11.5.5.5 of RDSO/SPN/176/2013, Ver -3)	27000.0
11.5.5.4 (Clause 11.5.5.4, of RDSO/SPN/176/2013,version 3, Damp Heat Test ( Cyclic) as per IS-9000/Pt.V, Sec-2)	30000.0
11.5.5.3 (Cold Test , Clause No. 11.5.5.3 of RSDO/SPN/176/2013,version 3, and as per IS 9000/Part II Sec 3 Temp : -10 Deg C +2/-2 Deg C duration 2 Hrs)	6000.0
11.5.5.2 (Dry Heat Test , Clause No. 11.5.5.2 of RSDO/SPN/176/2013,version 3, and as per IS 9000/Part III Sec 5 Temp : +70 Deg C +2/-2 Deg C duration 16 Hrs)	10000.0
11.5.4 (Insulation Resistance Test as per Clause 11.5.4 of IDSO/SPN/176/2013, Ver 3)	6000.0
11.5.3 (Applied High Voltage Test as per Clause 11.5.3 of RDSO/SPN/176/2013, Ve. 3)	5000.0
11.8.8 (Vibration Test as per RSDO/SPN/176/2013, Ver. 3 and IS : 9000, Part -VIII Frequency : 10 Hz to 55 Hz Amp : 0.35 to to peak or 5 g Nos of axis:3 Nos of sweep cycle :20 Duration :1 Hrs 45 Min)	15000.0

526

NTHER-Calibration of Standard Capacitor - Calibration of Standard Capacitor

Calibration of Standard Capacitor

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Calibration of Capacitance)	1500.0

527

IS 14223 : Part 1 (1995) - Polished Building Stones: Part 1 Granite

Polished Building Stones: Part 1 Granite

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Resistance to wear)	4000.0
5 (Hardness)	2000.0
5 (Ultrasonic pulse velocity)	5000.0
5 (Shear strength)	2000.0
5 (Tensile strength)	2000.0
5 (Porosity)	1000.0
5 (Water absorption)	1000.0
5 (Compressive strength)	2000.0
5 (Specific gravity)	1000.0
5 (Dry density )	1000.0
5 (Moisture content)	500.0
4 (Dimensions)	500.0

528

IS 3316 (1974) - Structural Granite

Structural Granite

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Water Absorption)	1000.0
3.2 (Specific Gravity)	1000.0
3.1 (Compressive Strength)	2000.0

529

IS 1125 (1974) - Natural Building Stone

Natural Building Stone

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

530

IEC 61427-1: 2013 (2013) - Secondary cells and batteries for renewable energy storage - General requirements and methods of test- Part 1: Photovoltaic off-grid application

Secondary cells and batteries for renewable energy storage - General requirements and methods of test- Part 1: Photovoltaic off-grid application

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Capacity Test)	60000.0
8.3 (Charge retension test)	25000.0
8.4 (Cycling endurance test in photovoltaic applications(extreme conditions))	70000.0

531

IS 5154(Part 1 & 2): 2013 (2013) - Lead Acid Traction Batteries

Lead Acid Traction Batteries

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 of IS 5154(Part-1)-2013 (5 h Capacity Test)	25000.0
5.5 of IS 5154 (Part-1)-2013 (Cyclic Endurance Test)	90000.0
3 and 5 of IS 5154(Part-2)-2013 (Dimensions of Traction Batteries)	1000.0
5.4 (1 h High rate discharge performance test)	20000.0
5.3 (Charge retention test)	20000.0

532

Custom-32-ER-LM - Load Testing of Mounting Fixtures

Load Testing of Mounting Fixtures

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Load Testing of the Mounting Fixture for 72Hours)	15000.0

533

IEC 61439-1: 2009 & IS/IEC:60529-2001 - IP-65 Class of protection test Drawing Verification Power Frequency Voltage withstand test before and after IP test Dielectric Properties test before and after IP test

IP-65 Class of protection test Drawing Verification Power Frequency Voltage withstand test before and after IP test Dielectric Properties test before and after IP test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (IP-65 Class of Protection test)	15000.0
2 (Drawing verification)	3000.0
3 (Power frequency voltage withstand test)	5000.0
4 (Di-electric properties test)	5000.0

534

IS/IEC:60529-2001 & IEC 61439-1: 2009 - IP-42 Class of protection test Drawing Verification Power Frequency Voltage withstand test after IP test Dielectric Properties test after IP test

IP-42 Class of protection test Drawing Verification Power Frequency Voltage withstand test after IP test Dielectric Properties test after IP test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (IP-42 Class of protection test)	15000.0
2 (Drawing verification)	3000.0
3 (Power Frequency voltage withstand test)	2500.0
4 (Di-electric Properties test)	5000.0

535

JSG 0102:1984 - JOINT SERVICES GUIDE ON ENVIRONMENTAL TESTING ON ARMAMENT STORES

JOINT SERVICES GUIDE ON ENVIRONMENTAL TESTING ON ARMAMENT STORES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
As per specification & customer requirements (Discrete Tests)	65000.0

536

IS 1708(Parts 1-18)1986: RA 2020 - METHODS OF TESTING OF SMALL CLEAR SPECIMENS OF TIMBER

METHODS OF TESTING OF SMALL CLEAR SPECIMENS OF TIMBER

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Moisture content (IS 1708(1):1986))	1000.0
2 (Specific gravity (IS 1708(2):1986))	500.0
3 (Volumetric Shrinkage (IS 1708(3)1986))	1000.0
5 (Static bending strength (IS 1708(5):1986) 1.Fibre stress at limit of proportionality(FS at LP) 2.Equivalent fibre stress at maximum load(MOR) 3.Modulus of Elasticity( M of E) 4.Horizontal shear(HS)stress on neutral plan at LP 5.Horizontal shear stress at maximum load(ML) 6.Wk to LP 7.Wk to ML)	3000.0
15 (Screw holding power(IS 1708(15):1986))	1500.0
8 (Compressive strength-Parallel to grain(IS 1708(8)1986))	1500.0
9 (Compressive strength-Perpendicular to grain(IS 1708(9):1986))	1500.0
12 (Tensile strength -Parallel to grain(IS 1708(12):1986))	2000.0

537

AMS 2630B (1995) - AEROSPACE MATERIAL SPECIFICATION

AEROSPACE MATERIAL SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1.1 (Ultrasonic Testing)	2000.0

538

NTH ER HIGH POLYMER LAB (2022) - GLORIA BLUE Color L*A*B* value testing using D65 light Source

GLORIA BLUE Color L*A*B* value testing using D65 light Source

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (GLORIA BLUE Color LAB* value testing using D65 light Source)	10000.0

539

ND Custom 6 (2023) - Aluminium and Aluminium Alloy Plates

Aluminium and Aluminium Alloy Plates

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Tensile and Bend Test)	4500.0

540

IS 398 : Part 5 (1992) - Aluminium conductor for overhead transmission purposes - Specification: Part 5 aluminium conductors - Galvanized steel - Reinforced for extra high voltage (400 KV And Above) (First Revision)

Aluminium conductor for overhead transmission purposes - Specification: Part 5 aluminium conductors - Galvanized steel - Reinforced for extra high voltage (400 KV And Above) (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13.3 (Measurement of Diameters of Individual Aluminium and Steel Wires)	1000.0
13.4 (Measurement of Lay Ratio)	2000.0
13.5.2 (Breaking Load Test on Individual Wires)	3500.0
13.6 (Ductility Test)	3500.0
13.7 (Wrapping Test)	1000.0
13.8 (Resistance Test)	5000.0
13.9 (Galvanizing Test)	2000.0