NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb@nic.in

Scope List

Reset

1161 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

391

NTHER- Calibration of Furnace - Calibration of Furnace

Calibration of Furnace

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Calibration of parameter Temperature)	6000.0
A2 (Calibration of parameter Temperature)	8000.0

392

NTHER Calibration of Hot air Oven - Calibration of Hot air Oven

Calibration of Hot air Oven

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Calibration of parameter Temperature)	6000.0
A2 (Calibration of parameter Temperature)	8000.0

393

17880 (2022) - GEOSYNTHETICS — SYNTHETIC POLYMER ROPE GABIONS FOR COASTAL AND WATERWAYS PROTECTION — SPECIFICATION

GEOSYNTHETICS — SYNTHETIC POLYMER ROPE GABIONS FOR COASTAL AND WATERWAYS PROTECTION — SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.0 (Breaking Strength of Rope)	5000.0
7.0 (Breaking Strength After Thermal Stability at 45 °C for 3 hours)	7000.0

394

IS 374:2019 (2019) - Electric Ceiling Type Fans - Specification

Electric Ceiling Type Fans - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Starting)	500.0
12 (Interchangeability)	500.0
15.1 (Air Delivery Test)	10000.0
15.1 (Service Value Test)	500.0
14.5 (Power Factor)	500.0
14.4 (Measurement of speed of Fan)	500.0
9 (Cl.24 of IS 302-2-80) (Safety Requirements, Components)	500.0
9 (Cl.29 of IS 302-2-80) (Safety Requirements,Creepage Distance & Clearance distance)	500.0
9 (Cl.11 of IS 302-2-80) (Safety Requirements,Heating)	500.0
9 (Cl.23 of IS 302-2-80) (Safety Requirements,Internal Wiring)	500.0
9 (Cl.16 of IS 302-2-80) (Safety Requirements,Leakage Current and Electric Strength)	1000.0
9 (Cl.21 of IS 302-2-80) (Safety Requirements,Mechanical Strength)	1000.0
9 (Cl.15 of IS 302-2-80) (Safety Requirements,Moisture resistance test)	1000.0
9 (Cl.10 of IS 302-2-80) (Safety Requirements,Power Input and Current)	1000.0
9 (Cl.8 of IS 302-2-80) (Safety Requirements,Protection against access to live parts)	500.0
9 (Cl.27 of IS 302-2-80) (Safety Requirements,Provision for earthing)	500.0
9 (Cl.31 of IS 302-2-80) (Safety Requirements,Resistance to rusting)	500.0
9 (Cl.25 of IS 302-2-80) (Safety Requirements,Supply connection and external flexible cords)	500.0
9 (Cl.14 of IS 302-2-80) (Safety Requirements,Transient overvoltage)	500.0
9 (Cl.13 of IS 302-2-80) (Safety Requirements,Leakage Current and Electric Strength at operating temperature)	1000.0
9 (Cl.28 of IS 302-2-80) (Safety Requirements,Screws and Connection)	500.0
13 (Silent Operation)	500.0
17 (TEST FOR HARMONIC DISTORTION)	5000.0

395

CUSTOM - Distance bush to grade RDSO

Distance bush to grade RDSO

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon, Percent)	1200.0
2 (Manganese, Percent)	1200.0
3 (Silicon, Percent)	1200.0
4 (Sulphur, Percent)	1200.0
5 (Phosphorus, Percent)	1200.0
6 (Chromium Percent)	1200.0
7 (Molybdenum, Percent)	1200.0
8 (Nickel, Percent)	1200.0
9 (Others)	1200.0

396

CUSTOM-BOLT FOR FIAT-EN36A - BOLT FOR FIAT-EN36A

BOLT FOR FIAT-EN36A

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon ,Percent)	1200.0
2 (Silicon, Percent)	1200.0
3 (Manganese, Percent)	1200.0
4 (Nickel, Percent)	1200.0
5 (Chromium, Percent)	1200.0
6 (Molybdenum, Percent)	1200.0
7 (Sulphur, Percent)	1200.0
8 (Phosphorus, Percent)	1200.0

397

4432 - SPECIFICATION FOR CASE HARDENING STEELS

SPECIFICATION FOR CASE HARDENING STEELS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon, Percent by mass)	1200.0
2 (Silicon, Percent)	1200.0
3 (Manganese, Percent)	1200.0
4 (Nickel, Percent)	1200.0
5 (Chromium, Percent)	1200.0
6 (Molybdenum, Percent)	1200.0
7 (Sulphur, Percent)	1200.0
8 (Phosphorus, Percent)	1200.0

398

IS:7098(Part 1)-1988 - Cross linked polyethylene insulated PVC sheathed cables, Part 1: For working voltage upto and including 1 100 V

Cross linked polyethylene insulated PVC sheathed cables, Part 1: For working voltage upto and including 1 100 V

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1 a) iv, b, c, d) i, ii, iii, iv e) i, ii, iii, iv, vi, viii, f, g,h (Discrete tests as per IS:7098(Part-1)-1988)	22000.0

399

JHA BABA Specification (2023) - TEST of Environment

TEST of Environment

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (HV test at 1.5 KV between live parts & neutral of MCB, Duration 1 Minute)	3000.0
2 (IP 5X protection against Dust Test as per Clause 7.5 Table Cl of IS 13947 Part 1 ,1993)	7500.0
3 (HV Test at 1.5 KV between Live & Neutral of MCB, Duration 01 Min)	3000.0
4 (IP X 5 Protection against water Jet Nozzle Dia : 6.3 mm water Pressure 0.3 Bar Distance :3 Meter Duration :03 Minutes)	7500.0
5 (High Voltage test at 1.5KV between live parts and neutral of MCB, Duration 1 Min)	3000.0

400

IS 7608 (1987) - Specification for phosphor bronze wire for general engineering purposes (First Revision)

Specification for phosphor bronze wire for general engineering purposes (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Freedom from defects - Surface Finish)	1000.0
7.1 (Tensile Strength. (wire dia. 0.45 to 6.0 mm))	1500.0
7.1 (Elongation percent of gauge length.)	1500.0
7.2 (Wrapping Test.)	1000.0
8 (Diameter of the wire.)	1000.0
6 (Tin)	500.0
6.1 (Phosphorus)	500.0
6.1 (Lead)	500.0
6.1 (Copper)	500.0
6.1 (Total Impurities)	1000.0

401

Custom-30-ER-LM - Load Test on Solar Road Stud

Load Test on Solar Road Stud

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Load Test on Winch)	4000.0
2 (Load Test on Solar Road Stud)	5000.0

402

IS 516 : Part 5 : Sec 4 (2020) - Hardened Concrete Methods of Test Part 5 Non-Destructive Testing of Concrete Section 4 Rebound Hammer Test ( First Revision )

Hardened Concrete Methods of Test Part 5 Non-Destructive Testing of Concrete Section 4 Rebound Hammer Test ( First Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Rebound hammer test (field test) -per Ten locations)	15000.0
- - (Scientist charges (2 Scientists) for site testing / inspection)	10000.0

403

RDSO TI/SPC/PSI/ISOLTR/0210 - 25KV Motorised/Manual operated and 50KV/66KV/100KV/110KV/132KV/220KV Manual operated single pole,Double pole and Triple Pole Isolators for Railway Electric Traction

25KV Motorised/Manual operated and 50KV/66KV/100KV/110KV/132KV/220KV Manual operated single pole,Double pole and Triple Pole Isolators for Railway Electric Traction

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Visual Examination)	1000.0
7.2 (Dimension)	2000.0
7.10 (Mass of Zinc Coating as per ETI/OHE/13)	2000.0
7.10 (Adherence Test as per ETI/OHE/13)	2000.0
7.10 (Uniformity of coating as per ETI/OHE/13)	1000.0
7.11.1 (Chemical Analysis)	5000.0
7.11.2 (Physical Test on Fasteners as per RDSO specification No. TI/SPC/OHE/FASTENERS/0120)	5000.0
7.11.3 (Physical Test on Copper Strips as per IS 1897)	8000.0

404

EIL SOLVENT FREE GLASS FLAKE REINFORCED EPOXY (Two Pack) (0) - SOLVENT FREE GLASS FLAKE REINFORCED EPOXY (Two Pack)

SOLVENT FREE GLASS FLAKE REINFORCED EPOXY (Two Pack)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (SOLID CONTENT (%))	1000.0
2 (DRY FILM THICKNESS/COAT (Microns) ASTM-D-4400-84)	1000.0
3 (RESISTANCE TO WET TEMPERATURE:14 deg C TO 60 deg C)	10000.0
4 (IMPACT RESISTANCE at 250 microns coating at 23 deg C reverse and direct ASTM G14)	3000.0
5 (ABRASION RESISTANCE at 1000g weight /1000 cycles /CS-17 ASTM D4060 loss in mg)	5000.0
7 (ADHESION TO STEEL (Mpa) ASTM D 4541)	5000.0
8 (HARDENESS: SHORE D ASTM D 3363)	3500.0
9 (WATER ABSORPTION FOR IMMERSION OF 30 DAYS (g/m2) ASTM -D-570)	3000.0
10 (SALT SPRAY TEST FOR 1440 hrs ISO 7253)	35000.0
11 (HOLIDAY TEST at low voltage up to 2 kv at 500 microns DFT ASTM D 5162)	2500.0
12 (MASS DENSITY OF base and hardener (wt. per ltr) (gm/cm3) ASTM D 1475)	1200.0
13 (Drying Time TOUCH DRY at 30 deg C ASTM D 1640)	1200.0
13 (FULL CURING FOR SERVICE EXPOSURE ASTM D 1640)	1200.0
14 (INTER COAT ADHESION ASTM D 3359)	1200.0
15 (EPOXY EQUIVALENT ASTM D 1652)	3500.0
16 (Overcoating Interval time For Second coat ASTM D 1640)	200.0

405

RDSO/SPN/176/2013 ver 3.0 eff date 31.03.2014 (2014) - Specification for Multi Section Digital Axel Counter

Specification for Multi Section Digital Axel Counter

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11.5.5.6 (Salt Mist Test(RDSO/SPN/144/2014) Test Condition:2 hours +22 Hours(Mist + Damp Heat) Temperature:35 (+/-)3 deg C Humidity:93 % (+2% ,-3%))	5000.0

406

NTH PAINT 2023 Water Based PU Waterproofing Compound (2023) - Water Based PU Waterproofing Compound (Cold liquid Elastomeric Waterproofing )

Water Based PU Waterproofing Compound (Cold liquid Elastomeric Waterproofing )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Colour & Apperance)	200.0
2 (Specific gravity at 30Deg C)	1000.0
3 (Solid Content % by mass)	1000.0
4 (Dry Film Thickness ,(DFT) in mm)	1000.0
5 (Elongation @break %)	2000.0
6 (QUV test for 200 hours (Fluorescent UV-Condensation) Exposures ASTM D4587)	8000.0
7 (Tensile Strength N/mm2)	1000.0
8 (Pull off Adhesion Strength (ASTM D 4541) on concrete Substrate)	3500.0
9 (Water Vapor Permeability Test ASTM D1653)	2000.0
10 (Surface Drying Time)	500.0

407

ND Custom 8 (2023) - Load test for steel roller Assembly

Load test for steel roller Assembly

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Compressive Load Test)	10000.0

408

IS 3384 (1986) - bitumen primer for use in waterproofing and damp-proofing

bitumen primer for use in waterproofing and damp-proofing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (i) (Viscocity 25dg,tar viscometer 4mm orifice)	1200.0
ADDITIONAL pARAMETER (Specific gravity)	1200.0

409

IS 1367 : Part 13 (2020) - Technical Supply Conditions for Threaded Steel Fasteners Part 13 Hot Dip Galvanized Coatings on Threaded Fasteners ( Third Revision )

Technical Supply Conditions for Threaded Steel Fasteners Part 13 Hot Dip Galvanized Coatings on Threaded Fasteners ( Third Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3 (Coating Thickness)	2000.0

410

IS 1254 (2007) - Corrugated aluminium sheet (Fourth Revision)

Corrugated aluminium sheet (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Dimension)	1000.0
6 (Aluminium)	500.0
6 (Copper)	600.0
6 (Magnesium)	500.0
6 (Silicon)	500.0
6 (Iron)	600.0
6 (Manganese)	500.0
6 (Zinc)	600.0
6 (Titanium)	600.0
6 (Chromium)	600.0
7.1 (Tensile strength)	1000.0
6 (0.2% Proof Stress)	1000.0
6 (Elongation on 50 mm Gauge Length)	1000.0
6 (Bend Test)	1500.0

411

CUSTOM-12-ER-MCALI - Poldi Hardness Tester

Poldi Hardness Tester

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Hardness)	4000.0

412

CUSTOM-11-ER-MCALI - Dynamic Hardness Tester (HRC, HRB & HBW)

Dynamic Hardness Tester (HRC, HRB & HBW)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Hardness (HRC,HRB & HBW))	12000.0

413

CUSTOM-10-ER-MCALI - Steel Bar

Steel Bar

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension)	1200.0

414

CUSTOM-09-ER-MCALI - Ultrasonic Step Gauge

Ultrasonic Step Gauge

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension)	2000.0

415

IS 101 Part 1 Section 7 (2020) - Methods of Sampling and Test for Paints, Varnishes and Related Products - Part 1 Test on Liquid Paints ( General and Physical ) - Section 7 Mass per 10 litres-Determination of density-Pycnometer method

Methods of Sampling and Test for Paints, Varnishes and Related Products - Part 1 Test on Liquid Paints ( General and Physical ) - Section 7 Mass per 10 litres-Determination of density-Pycnometer method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Volume of Pyknometer)	2000.0

416

CUSTOM-08-ER-MCALI - DIAL GAUGE OF PENETROMETER

DIAL GAUGE OF PENETROMETER

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (DIMENSION)	2000.0

417

IS 9440 (1979) - Laboratory Balances

Laboratory Balances

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Double Pan Balance)	4000.0

418

IS 9537(Part-I)-1980 & (Part-3)-1983 - SPECIFICATION FOR CONDUITS FOR ELECTRICAL INSTALLATIONS

SPECIFICATION FOR CONDUITS FOR ELECTRICAL INSTALLATIONS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (MARKING)	1000.0
7.1 (Outside Dia)	2000.0
9.2 (Bending test)	2500.0
9.3 (Compression test)	2000.0
9.4 (Impact test)	3000.0
10 (Resistance to heat)	5000.0
11 (Resistance to burning)	2000.0
12.1.2 (Insulation Resistance)	5000.0
12.1.1 (Electrical Strength)	5000.0

419

IS 737 - WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES - SPECIFICATION

WROUGHT ALUMINIUM AND ALUMINIUM ALLOY SHEET AND STRIP FOR GENERAL ENGINEERING PURPOSES - SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Dimension)	1000.0
7.2 (Bend Test)	1500.0
7.1 (Tensile strength)	2000.0
7.1 (0.2% Proof Stress)	1000.0
7.1 (Elongation on 50 mm Gauge Length)	1000.0
6 (Aluminium)	500.0
6 (Copper)	1000.0
6 (Magnesium)	500.0
6 (Silicon)	500.0
6 (Iron)	500.0
6 (Manganese)	500.0
6 (Zinc)	500.0
6 (Titanium)	500.0
6 (Chromium)	30.0
0 (Thickness of Anodic Coating)	2000.0

420

IS 9537 (Part 1 & 3) - SPECIFICATION FOR CONDUITS FOR ELECTRICAL INSTALLATIONS

SPECIFICATION FOR CONDUITS FOR ELECTRICAL INSTALLATIONS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found