NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1274 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

331

IS 3975 (1999) - Low carbon galvanized steel wires, formed wires and tapes for armouring of cables

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2 (Sulphur)	500.0
6.2 (Phosphorus)	500.0
7 (Dimension)	1000.0
8.1 (Tensile Strength)	2000.0
8.2 (Torsion Test for round wire only)	1000.0
8.3 (Wrapping Test)	1000.0
8.4 (Resistance Test for round and formed wire)	2000.0
9.1 (Mass of Zinc Coating)	2000.0
9.2 (Uniformity of Coating)	1000.0
9.3 (Adhesion Test)	1000.0
11 (Freedom from defect)	1000.0
8.1 (% Elongation)	1000.0

332

11087. (1986) - Specification For Paper For Magnetic Ink Character Recognition Cheque Printing.

Specification For Paper For Magnetic Ink Character Recognition Cheque Printing.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Description)	1000.0
3.2 (Absence of Magnetizable Particles.)	1000.0
3.3 (Substance)	1000.0
3.4 (Thickness)	1000.0
3.5 (Sizes)	1000.0
3.6 (Smoothness)	1000.0
3.6 (Porosity)	1000.0
3.6 (Opacity)	2000.0
3.6 (Wax pick)	2000.0
3.6 (Tearing Strength)	2000.0
3.6 (Stiffness)	1000.0
3.9 (Chemical Sensitize Test)	10000.0
Firm's request (UV Sensitization Test (24 hrs))	1200.0

333

CUSTOMER SPECIFICATION PAINT LAB (0) - CUSTOMER SPECIFICATION PAINT LAB

CUSTOMER SPECIFICATION PAINT LAB

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Salt spray test 24 hours, after 48 hours, after 72 hours ,after 96 hours &after 120 hours I)Delta E Value (before Exposure) II)Delta E Value (after Exposure) III)Gloss Value (before Exposure) iv) Gloss Value (after Exposure))	8000.0
2 (Rusting/corrosion test as per ASTM B-117 Test results after 24, 48, 72, 96 and 120 hours exposure of salt spray for rusting/corrosion evaluation)	6000.0
3 (Salt Spray Test 96 hrs.)	4800.0
4 (Dry film thickness)	1200.0
5 (Cross hatch adhesion test)	1500.0
6 (Impact resistance test)	1500.0
7 (Pencil hardness test)	1500.0
8 (Bend Test)	1200.0
9 (Gloss)	1200.0
10 (Salt Spray (ASTM B117) 100 hrs)	5000.0
11 (Wasahbility and cleanibility)	2000.0
12 (Drying Time (a) Surface dry)	1200.0
13 (Drying time (b) Hard dry)	1200.0
14 (Finish)	1200.0
15 (VOC (%by mass))	3000.0
17 (Resistance to alkali)	1500.0
18 (Accelerated storage stability)	3000.0

334

12089 - SPECIFICATION FOR GRANULATED SLAG FOR THE MANUFACTURE OF PORTLAND SLAG CEMENT

SPECIFICATION FOR GRANULATED SLAG FOR THE MANUFACTURE OF PORTLAND SLAG CEMENT

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Manganese oxide)	1200.0
3.2 (Magnesium oxide)	1200.0
3.2 (Sulphide sulphur)	1200.0

335

1654:1992 - Lead Antimony Alloys-Specification

Lead Antimony Alloys-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Antimony)	1200.0
5.1 (Lead)	1200.0
5.1 (Arsenic)	1200.0
5.1 (Tin)	1200.0
5.1 (Copper)	1200.0
5.1 (Bismuth)	1200.0
5.1 (Iron)	1200.0
5.1 (Zinc)	1200.0
5.1 (Silver)	1200.0

336

CUSTOM - Mineral Wool

Mineral Wool

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Shot Content)	2000.0

337

4276 - Soyabean Oil- Specification

Soyabean Oil- Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.7 (Moisture and Insoluble impurities)	1200.0
5.7 (Colour on the Lovibond scale, expressed as (Y + 5R))	1200.0
5.7 (Refractive index at 40ºC)	1200.0
5.7 (Saponification value)	1200.0
5.7 (Iodine value (Wijs))	1200.0
5.7 (Acid value, Max)	1200.0
5.7 (Unsaponifiable matter,)	1200.0

338

IS 16353 (2015) - Portland Cement Clinker - Specification

Portland Cement Clinker - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Insoluble residue)	600.0
5 (Total loss on ignition)	600.0
5 (Alkali content expressed as sodium oxide(Na2O))	1200.0
5 (Magnesia)	600.0
5 (Chloride content)	500.0
5 (Free lime)	600.0
5 (Total Sulphur content calculated as sulphuric anhydride(SO3))	500.0
5 (C3S + C2S)	600.0
5 (C3A)	600.0
5 (C3S)	600.0
5 (Ratio of percentage of alumina to that of iron oxide)	600.0
5 (Ratio of percentage of lime to percentage of silica, alumina and iron oxide)	600.0

339

F-17 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 (0) - F-17 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

F-17 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume of Solids % (ASTMD 2697 Air drying method ))	1500.0
2 (Dry Film Thickness per coat, microns)	1200.0
3 (Theoretical coverage m2/litre/coat)	1500.0
4 (weight per litre in Kg/litre of mix paint)	1200.0
5 (Touch Dry @ 30°C in Hours)	500.0
6 (Hard Dry Time @ 30°C in Hours)	500.0
7 (Full Cure @ 30°C)	1500.0
8 (Overcoating Intervals Hours)	1200.0
9 (Pot Life in Hrs)	1200.0
10 (Adhesion ASTM D 4541 in Mpa)	3500.0
11 (Temperature Resistance (at 150 Deg C ASTM D 2485 (Method A))	1500.0

340

F-20 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 (0) - F-20 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

F-20 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume of Solids % (ASTMD 2697 Air drying method ))	1500.0
2 (Dry Film Thickness per coat, microns)	1200.0
3 (Theoretical coverage m2/litre/coat)	1200.0
4 (weight per litre in Kg/litre)	1500.0
5 (Touch Dry @ 30°C Hours)	500.0
6 (Hard Dry Time @ 30°C ; Hours)	500.0
7 (Full Cure @ 30°C in hours)	1000.0
8 (Overcoating Intervals Hours)	1500.0
9 (Pot Life)	1500.0
10 (Adhesion ASTM D 4541 Mpa)	3500.0
11 (Tensile Strength ( ASTM D638) N/mm2)	5000.0
12 (Temperature Resistance (at 90 Deg C ASTM D 2485 Method A)	2500.0

341

F-9 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 (0) - F-9 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEWCONSTRUCTION

F-9 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEWCONSTRUCTION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume of Solids % (ASTMD 2697 Air drying method ))	1500.0
2 (Dry Film Thickness per coat in microns)	1200.0
3 (Theoretical coverage m2/litre/coat)	1500.0
4 (weight per litre in Kg/litre)	1500.0
5 (Touch Dry @ 30°C)	500.0
6 (Hard Dry Time @ 30°C in; Hours)	500.0
7 (Overcoating Intervals Hours)	1500.0
8 (Pot Life)	1200.0
9 (Adhesion ASTM D 4541)	3500.0
10 (MEK rub test ASTM D4752)	1500.0
11 (% Zinc Content on dry film)	2000.0
12 (Temperature Resistance at 400 Deg C ASTM D 2485 Method B)	1500.0

342

F6B EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 (0) - F6B EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

F6B EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume of Solids % (ASTMD 2697 Air drying method ))	1500.0
2 (Dry Film Thickness per coat, microns)	1200.0
3 (Theoretical coverage m2/litre/coat)	1200.0
4 (weight per litre in Kg/litre)	1200.0
5 (Touch Dry @ 30°C)	500.0
6 (Hard Dry Time @ 30°C)	500.0
7 (Full Cure @ 30°C)	1200.0
8 (Overcoating Intervals Hours)	1500.0
9 (Pot Life in hours)	1500.0
10 (Adhesion ASTM D 4541)	3500.0
11 (Temperature Resistance at 80Deg C Method A ASTM D 2485)	1500.0

343

F6A -EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 (0) - F6A -EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

F6A -EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume of Solids % (ASTMD 2697 Air drying method ))	1500.0
2 (Dry Film Thickness per coat, microns)	1300.0
3 (Theoretical coverage m2/litre/coat)	1000.0
4 (weight per litre in Kg/litre)	1000.0
5 (Touch Dry @ 30°C in Hours)	500.0
6 (Hard Dry Time @ 30°C in Hours)	500.0
7 (Full Cure @ 30°C)	1500.0
8 (Overcoating Intervals Hours)	1500.0
9 (Pot Life in hours)	1000.0
10 (Adhesion ASTM D 4541)	3500.0
11 (Temperature Resistance at 80 Deg C ASTM D 2485 Method A)	2500.0

344

F-2 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 (0) - F-2 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

F-2 EIL SPECIFICATION B269-000-02-42-PCS-0001 Rev. 2 SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM - NEW CONSTRUCTION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume of Solids % (ASTMD 2697 Air drying method ))	1500.0
2 (Dry Film Thickness per coat, microns)	1000.0
3 (Theoretical coverage m2/litre/coat)	1000.0
4 (weight per litre in Kg/litre)	500.0
5 (Touch Dry @ 30°C Hours)	500.0
6 (Hard Dry Time @ 30°C Hours)	500.0
7 (Overcoating Intervals Hours)	1000.0
8 (Pot Life in Hrs for two component paints)	1000.0
9 (Adhesion ASTM D 4541)	3500.0
10 (Abrasion Resistance ASTM D 4060 For 1000 g load/1000 cycles CS-17 wheel)	3500.0
11 (Temperature Resistance (at 80 deg C.) Method A- ASTM D 2485)	2500.0

345

IS 16651 (2017) - High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement

High Strength Deformed Stainless Steel Bars and Wires for Concrete Reinforcement

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3 (Carbon)	500.0
4.3 (Sulphur)	500.0
4.3 (Phosphorus)	500.0
4.3 (Silicon)	500.0
4.3 (Manganese)	500.0
4.3 (Chromium)	500.0
4.3 (Nickel)	500.0
4.3 (Molybdenum)	500.0
4.3 (Copper)	500.0
9.3 (Bend Test)	1000.0
5.2 (Rib Area)	1000.0
7.2 (Nominal Mass per meter Run)	1000.0
9.4 (Rebend Test (Upto 25 mm))	1000.0
8.6 (Charpy Impact Test at Room Temperature)	5000.0
9.2 (0.2 % Proof Stress / Yield Stress)	1000.0
9.2 (Elongation Percent on gauge length of 5.65 Square Root of Cross- Sectional Area)	500.0
9.2 (Total Elongation at Maximum Force on gauge length of 5.65 Square Root of Crosss- Sectional Area,)	500.0
9.2 (Tensile Strength (up to 12 mm),)	500.0
9.2 (Tensile Strength (16 to 25 mm))	1000.0
9.2 (Tensile Strength (32 mm))	1500.0
9.4 (Rebend Test (32 mm))	1500.0
5.7 (Bond Stress of deformed bar at Ultimate Failure (for size up to 12 mm))	1250.0
5.7 (Bond Stress of plain bar at Ultimate Failure (for size up to 12 mm))	1250.0
5.7 (Percentage increase in Bond Stress of Deformed Bar against corresponding Plain Bar at 0.25 mm slip (For size up to 12 mm ))	1250.0
5.7 (Bond Stress of deformed bar at 0.25 mm slip (for size up to 12 mm))	1250.0
5.7 (Bond Stress of Plain bar at 0.25 mm slip (for size up to 12 mm))	1250.0
5.7 (Percentage increase in Bond Stress of Deformed Bar against corresponding Plain Bar at 0.025 mm slip (For size up to 12 mm))	1250.0
5.7 (Bond Stress of Deformed bar at 0.025 mm slip (for size up to 12 mm))	1250.0
5.7 (Bond Stress of Plain bar at 0.025 mm slip (for size up to 12 mm))	1250.0
5.7 (Bond Stress of Plain bar at 0.025 mm slip (for size 16 to 32 mm))	1875.0
5.7 (Bond Stress of deformed bar at 0.025 mm slip (for size 16 to 32mm))	1875.0
5.7 (Percentage increase in Bond Stress of Deformed Bar against corresponding Plain Bar at 0.025 mm slip (for size 16 to 32 mm))	1875.0
5.7 (Bond Stress of Plain bar at 0.25 mm slip (for size 16 to 32 mm))	1875.0
5.7 (Bond Stress of deformed bar at 0.25 mm slip (for size 16 to 32 mm))	1875.0
5.7 (Percentage increase in Bond Stress of Deformed Bar against corresponding Plain Bar at 0.25 mm slip (for size 16 to 32 mm),)	1875.0
5.7 (Bond Stress of plain bar at Ultimate Failure (for size 16 to 32 mm))	1875.0
5.7 (Bond Stress of deformed bar at Ultimate Failure (for size 16 to 40 mm))	1875.0

346

IS 7098 : Part 1 : 1988 (Reaffirmed Year : 2020), Amendments : 5 - Crosslinked polyethylene insulated PVC sheathed cables: Part 1 For working voltage up to and including 1100 V

Crosslinked polyethylene insulated PVC sheathed cables: Part 1 For working voltage up to and including 1100 V

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1.a.i , 15.2.a (Tests on Conductor - Annealing Test (for copper))	1000.0
15.1.a.ii , 15.2.b (Tests on Conductor - Tensile Test (for Aluminium))	1000.0
15.1.a.iii , 15.2.c (Tests on Conductor - Wrapping Test (for Aluminium))	500.0
15.1.a.iv , 15.2.d (Tests on Conductor - Resistance Test)	2000.0
15.1.b.1 (Test for round steel wire/formed steel wire(strip) armour - Dimensions)	500.0
15.1.b.2.i (Test for round steel wire/formed steel wire(strip) armour - Tensile Strength)	1000.0
15.1.b.2.ii (Test for round steel wire/formed steel wire(strip) armour - Elongation at Break)	1000.0
15.1.b.2.iii (Test for round steel wire/formed steel wire(strip) armour - Torsion test for round wires)	1000.0
15.1.b.2.iv (Test for round steel wire/formed steel wire(strip) armour - winding test for formed wires)	1000.0
15.1.b.2.v (Test for round steel wire/formed steel wire(strip) armour - Uniformity of zinc coating)	1000.0
15.1.b.2.vi (Test for round steel wire/formed steel wire(strip) armour - Mass of zinc coating)	2000.0
15.1.b.2.vii (Test for round steel wire/formed steel wire(strip) armour - Resistivity)	2000.0
15.1.c , 15.2.e (Test for thickness of insulation and sheath)	1000.0
15.1.d.i , 15.2.g (Physical test for insulation - Tensile strength and elongation at breakj)	1500.0
15.1.d.ii (Physical test for insulation - Ageing in oven)	2000.0
15.1.d.iii , 15.2.f (Physical test for insulation - Hot set test)	1000.0
15.1.d.iv (Physical test for insulation - Shrinkage test)	1000.0
15.1.d.v (Physical test for insulation - Water absorption test (gravimetric)))	1000.0
15.1.e.i , 15.2.g (Physical tests for outer sheath - Tensile strength and elongation at break)	1000.0
15.1.e.ii (Physical tests for outer sheath - Ageing in air oven)	1000.0
15.1.e.iii (Physical tests for outer sheath - Loss of mass in air oven)	1000.0
15.1.e.iv (Physical tests for outer sheath - Shrinkage test)	500.0
15.1.e.v (Physical tests for outer sheath - Hot deformation test)	500.0
15.1.e.vi (Physical tests for outer sheath - Heat shock test)	500.0
15.1.e.vii (Physical tests for outer sheath - Thermal stability)	1000.0
15.1.f , 15.2.j (Insulation resistance (Volume resistivity test))	2000.0
15.1.g , 15.2.h (High voltage test)	2000.0
15.1.h (Flammability test)	500.0
15.1.1.C1.a , 15.1.1.C2.a , 15.2.1.C1.a , 15.2.1.C2.a (Oxygen Index Test (for Category C1 & C2))	5000.0
15.1.1.C1.b , 15.1.1.C2.b , 15.2.1.C1.b , 15.2.1.C2.b (Flame retardance test on single cable (for category C1 & C2))	5000.0
15.1.1.C1.c , 15.1.1.C2.c , (Flame retardance test on bunched cable)	5000.0
15.1.1.C1.d , 15.1.1.C2.g (Temperature Index)	5000.0
15.1.1.C2.e (Smoke density)	5000.0
15.1.1.C2.f , 15.2.1.C2.d (Test for halogen acid gas evolution)	5000.0
- (Test on 2nd Core)	2000.0
- (Test on 3rd Core)	2000.0
- (Test on 4th Core)	2000.0
- (Test on 5th Core)	2000.0
- (Test on 6th Core)	2000.0
- (Test on 7th core)	2000.0
- (Test on 8th Core)	2000.0

347

IS 7014 (1973) - Specification for Length Bars

Specification for Length Bars

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.4 (Length)	9600.0

348

IS 11103 (1984) - Specification for Cylindrical Measuring Pins (Size Range from 0.1 mm up to and Including 20 mm)

Specification for Cylindrical Measuring Pins (Size Range from 0.1 mm up to and Including 20 mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Diameter)	7500.0

349

Custom - Used cooked oil

Used cooked oil

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Moisture Content % by mass)	1200.0
2 (Density)	1200.0
3 (Free Fatty Acid)	1200.0
4 (Kinematic Viscosity at Room Temp)	1200.0

350

CUSTOM - Fly Ash

Fly Ash

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Loss on Ignition)	1200.0
2 (CaO)	1200.0
3 (Fe2O3)	1200.0
4 (MgO)	1200.0
5 (Al2O3)	1200.0
6 (SiO2)	1200.0

351

IRS:TC 30-05 (2006) - Underground railway jelly filled telecom quad cables for signalling & telecom installations

Underground railway jelly filled telecom quad cables for signalling & telecom installations

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.5.1 (Physical tests for conductor - Dimensions)	500.0
5.7 (Test for thickness of insulation and sheaths)	1000.0
5.8.2.3 (Physical tests for pe insulation, pe inner sheath, pvc intermediate and outer sheath - Shrinkage Test)	500.0
5.9.3 (Conductor resistance test)	1500.0
3.2.4 (Colour of insulated quad test)	500.0
5.9.1 (High voltage test)	3000.0
5.9.2.1 & 5.9.2.2 (Insulation Resistance Test)	3000.0
5.6.1 (Physical test for armour tapes - Dimensions)	1000.0
5.6.5 (Physical test for armour tapes - Test for closeness of armour)	1000.0
- (Testing on extra core of 24 Quad Cable)	46000.0
- (Testing of each extra core)	2000.0

352

IS 13410 (1992) - Glass reinforced polyester sheet moulding compounds(Smc) - Specification

Glass reinforced polyester sheet moulding compounds(Smc) - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.0 (Glass Content percent by mass)	3000.0
6.0 (Izod Impact Strength)	2000.0
6.0 (Tensile Strength)	2000.0
6.0 (Flexural Strength)	2000.0

353

IS 2095 : Part 1 (2011) - Gypsum Plaster Boards - Part 1 Plain Gypsum Plaster Boards

Gypsum Plaster Boards - Part 1 Plain Gypsum Plaster Boards

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3, Table3, 8.1 (Transverse Strength-IS: 2542 (Part 2/Sec 4))	4000.0
7.1, Table1 /Table2, 8.1 (Dimensions-IS: 2542 (Part 2/Sec 1))	500.0
7.2, 8.2 (Taper Profile-IS 2095 (1):2011)	2000.0

354

B269-000-02-42-PCS-0001 Rev. 3 (2021) - F-15 Two components Epoxy phenolic coating cured with polyamine adduct hardener EIL SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM

F-15 Two components Epoxy phenolic coating cured with polyamine adduct hardener EIL SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume solids %)	2000.0
2 (DFT per coat in microns)	500.0
3 (Theoretical covering capacity meter square/coat/litre)	500.0
4 (weight per litre of mix paint Kg/litre)	500.0
5 (Touch dry at 30 Deg C)	500.0
6 (Hard dry at 30Deg C)	500.0
7 (Full cure 30 Deg C(for immersion /high temp service))	500.0
8 (Over-coating interval)	1000.0
9 (Pot life at 30 Deg C(For two components paint))	1000.0
10 (Adhesion (ASTM D 4541) MPa)	3000.0
11 (Temperature Resistance at 150 Deg C Method A ASTM D 2485)	2500.0

355

EN 14399 Part-5 (2015) - High-strength structural bolting assemblies for Preloading –.Part 5: Plain washers

High-strength structural bolting assemblies for Preloading –.Part 5: Plain washers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Dimension)	2000.0
4 & Table-3 (Mechanical Properties Vickers Hardness)	2000.0
0 (Chemical Composition)	2000.0
4.0 (Zinc coating thickness as per ISO 10684)	2000.0

356

EN 14399 : Part 9 (2009) - High-Strength Structural Bolting Assemblies For Preloading - Part 9: System HR Or HV - Direct Tension Indicators For Bolt And Nut Assemblies

High-Strength Structural Bolting Assemblies For Preloading - Part 9: System HR Or HV - Direct Tension Indicators For Bolt And Nut Assemblies

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Internal Diameter)	500.0
3.1 (Protrusion internal Diameter)	500.0
3.1 (Protrusion tangential Diameter)	500.0
3.1 (Height of Protrusion)	500.0
3.1 (Height over Protrusion)	500.0
3.1 (Material Thickness)	500.0
3.1 (External Diameter)	500.0
3.1 (Dimensions as per EN 14399 - 9.)	2500.0
3.2 (Mechanical Properties Vickers Hardness)	2000.0

357

IS 277 (2018) - Galvanized Steel Sheets (Plain and Corrugated)

Galvanized Steel Sheets (Plain and Corrugated)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Uniformity of Zinc Coating)	2000.0
14 ,15 (Dimensions)	1000.0
5.1 (Carbon, % by mass)	500.0
5.1 (Manganese, % by mass)	500.0
5.1 (Sulphur, % by mass)	500.0
5.1 (Phosphorous, % by mass)	500.0
8.1 (Tensile Strength)	2000.0
8.1 (Yield Stress)	1000.0
8.1 (Elongation Percent)	1000.0
8.2 (Bend Test)	1000.0
12 (Freedom from Defects)	1000.0
5.1 (Titanium)	500.0
7 (Mass of Zinc Coating)	2000.0
3.3 (Thickness of Sheet)	1000.0
3.3 (Thickness of sheet (uncoated), mm)	1000.0

358

IS 1891 : Part 1 (2021) - CONVEYOR AND ELEVATOR TEXTILE BELTING – SPECIFICATION PART 1 GENERAL PURPOSE BELTING (Fifth Revision)

CONVEYOR AND ELEVATOR TEXTILE BELTING – SPECIFICATION PART 1 GENERAL PURPOSE BELTING (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.0 (Construction)	1000.0
7.0 (Tensile Strength of Top Cover)	1000.0
7.0 (Tensile Strength of Bottom Cover)	1000.0
7.0 (Elongation at Break of Top Cover)	500.0
7.0 (Elongation at Break of Bottom Cover)	500.0
7.0 (Abrasion Loss of Top Cover)	1500.0
7.0 (Abrasion loss of Bottom Cover)	1500.0
8.0 (Freedom from Defects)	1000.0
14.0 (Width)	1000.0
14.0 (Cover Thickness)	1000.0
15.0 (Full Thickness Tensile Strength, Longitudinal Direction)	2500.0
15.0 (Full Thickness Tensile Strength, Transverse Direction)	2500.0
15.0 (Full Thickness Elongation at Break, Longitudinal Direction)	500.0
15.0 (Full Thickness Elongation at Break, Transverse Direction)	500.0
15.0 (Elongation at Reference Load, Longitudinal Direction)	1000.0
16.0 (Adhesion Strength Between Plies)	3000.0
16.0 (Adhesion Strength Between Cover and Carcass)	2000.0
Firm's request (Hardness (Shore A))	1000.0
Firm's request (Flammability Characteristics with Cover (ISO 340))	4000.0
Firm's request (Flammability Characteristics without Cover (ISO 340))	4000.0

359

CUSTOM - Grease

Grease

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Consistency of the grease at 25±0.5°C, Unworked penetration)	1200.0
2 (Consistency of the grease at 25±0.5°C: 60 strokes)	1200.0
3 (Free alkalinity, percent by mass)	1200.0

360

CUSTOM - GOLD CONTENT (% by mass)

GOLD CONTENT (% by mass)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Gold % by mass)	2000.0