NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1226 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

301

CUSTOM - Fly Ash

Fly Ash

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Loss on Ignition)	1200.0
2 (CaO)	1200.0
3 (Fe2O3)	1200.0
4 (MgO)	1200.0
5 (Al2O3)	1200.0
6 (SiO2)	1200.0

302

IRS:TC 30-05 (2006) - Underground railway jelly filled telecom quad cables for signalling & telecom installations

Underground railway jelly filled telecom quad cables for signalling & telecom installations

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.5.1 (Physical tests for conductor - Dimensions)	500.0
5.7 (Test for thickness of insulation and sheaths)	1000.0
5.8.2.3 (Physical tests for pe insulation, pe inner sheath, pvc intermediate and outer sheath - Shrinkage Test)	500.0
5.9.3 (Conductor resistance test)	1500.0
3.2.4 (Colour of insulated quad test)	500.0
5.9.1 (High voltage test)	3000.0
5.9.2.1 & 5.9.2.2 (Insulation Resistance Test)	3000.0
5.6.1 (Physical test for armour tapes - Dimensions)	1000.0
5.6.5 (Physical test for armour tapes - Test for closeness of armour)	1000.0
- (Testing on extra core of 24 Quad Cable)	46000.0
- (Testing of each extra core)	2000.0

303

IS 13410 (1992) - Glass reinforced polyester sheet moulding compounds(Smc) - Specification

Glass reinforced polyester sheet moulding compounds(Smc) - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.0 (Glass Content percent by mass)	3000.0
6.0 (Izod Impact Strength)	2000.0
6.0 (Tensile Strength)	2000.0
6.0 (Flexural Strength)	2000.0

304

IS 2095 : Part 1 (2011) - Gypsum Plaster Boards - Part 1 Plain Gypsum Plaster Boards

Gypsum Plaster Boards - Part 1 Plain Gypsum Plaster Boards

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.3, Table3, 8.1 (Transverse Strength-IS: 2542 (Part 2/Sec 4))	4000.0
7.1, Table1 /Table2, 8.1 (Dimensions-IS: 2542 (Part 2/Sec 1))	500.0
7.2, 8.2 (Taper Profile-IS 2095 (1):2011)	2000.0

305

B269-000-02-42-PCS-0001 Rev. 3 (2021) - F-15 Two components Epoxy phenolic coating cured with polyamine adduct hardener EIL SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM

F-15 Two components Epoxy phenolic coating cured with polyamine adduct hardener EIL SPECIFICATION FOR SURFACE PREPARATION AND PROTECTIVE COATING SYSTEM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume solids %)	2000.0
2 (DFT per coat in microns)	500.0
3 (Theoretical covering capacity meter square/coat/litre)	500.0
4 (weight per litre of mix paint Kg/litre)	500.0
5 (Touch dry at 30 Deg C)	500.0
6 (Hard dry at 30Deg C)	500.0
7 (Full cure 30 Deg C(for immersion /high temp service))	500.0
8 (Over-coating interval)	1000.0
9 (Pot life at 30 Deg C(For two components paint))	1000.0
10 (Adhesion (ASTM D 4541) MPa)	3000.0
11 (Temperature Resistance at 150 Deg C Method A ASTM D 2485)	2500.0

306

EN 14399 Part-5 (2015) - High-strength structural bolting assemblies for Preloading –.Part 5: Plain washers

High-strength structural bolting assemblies for Preloading –.Part 5: Plain washers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Dimension)	2000.0
4 & Table-3 (Mechanical Properties Vickers Hardness)	2000.0
0 (Chemical Composition)	2000.0
4.0 (Zinc coating thickness as per ISO 10684)	2000.0

307

EN 14399 : Part 9 (2009) - High-Strength Structural Bolting Assemblies For Preloading - Part 9: System HR Or HV - Direct Tension Indicators For Bolt And Nut Assemblies

High-Strength Structural Bolting Assemblies For Preloading - Part 9: System HR Or HV - Direct Tension Indicators For Bolt And Nut Assemblies

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.1 (Internal Diameter)	500.0
3.1 (Protrusion internal Diameter)	500.0
3.1 (Protrusion tangential Diameter)	500.0
3.1 (Height of Protrusion)	500.0
3.1 (Height over Protrusion)	500.0
3.1 (Material Thickness)	500.0
3.1 (External Diameter)	500.0
3.1 (Dimensions as per EN 14399 - 9.)	2500.0
3.2 (Mechanical Properties Vickers Hardness)	2000.0

308

IS 277 (2018) - Galvanized Steel Sheets (Plain and Corrugated)

Galvanized Steel Sheets (Plain and Corrugated)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Uniformity of Zinc Coating)	2000.0
14 ,15 (Dimensions)	1000.0
5.1 (Carbon, % by mass)	500.0
5.1 (Manganese, % by mass)	500.0
5.1 (Sulphur, % by mass)	500.0
5.1 (Phosphorous, % by mass)	500.0
8.1 (Tensile Strength)	2000.0
8.1 (Yield Stress)	1000.0
8.1 (Elongation Percent)	1000.0
8.2 (Bend Test)	1000.0
12 (Freedom from Defects)	1000.0
5.1 (Titanium)	500.0
7 (Mass of Zinc Coating)	2000.0
3.3 (Thickness of Sheet)	1000.0
3.3 (Thickness of sheet (uncoated), mm)	1000.0

309

IS 1891 : Part 1 (2021) - CONVEYOR AND ELEVATOR TEXTILE BELTING – SPECIFICATION PART 1 GENERAL PURPOSE BELTING (Fifth Revision)

CONVEYOR AND ELEVATOR TEXTILE BELTING – SPECIFICATION PART 1 GENERAL PURPOSE BELTING (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.0 (Construction)	1000.0
7.0 (Tensile Strength of Top Cover)	1000.0
7.0 (Tensile Strength of Bottom Cover)	1000.0
7.0 (Elongation at Break of Top Cover)	500.0
7.0 (Elongation at Break of Bottom Cover)	500.0
7.0 (Abrasion Loss of Top Cover)	1500.0
7.0 (Abrasion loss of Bottom Cover)	1500.0
8.0 (Freedom from Defects)	1000.0
14.0 (Width)	1000.0
14.0 (Cover Thickness)	1000.0
15.0 (Full Thickness Tensile Strength, Longitudinal Direction)	2500.0
15.0 (Full Thickness Tensile Strength, Transverse Direction)	2500.0
15.0 (Full Thickness Elongation at Break, Longitudinal Direction)	500.0
15.0 (Full Thickness Elongation at Break, Transverse Direction)	500.0
15.0 (Elongation at Reference Load, Longitudinal Direction)	1000.0
16.0 (Adhesion Strength Between Plies)	3000.0
16.0 (Adhesion Strength Between Cover and Carcass)	2000.0
Firm's request (Hardness (Shore A))	1000.0
Firm's request (Flammability Characteristics with Cover (ISO 340))	4000.0
Firm's request (Flammability Characteristics without Cover (ISO 340))	4000.0

310

CUSTOM - Grease

Grease

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Consistency of the grease at 25±0.5°C, Unworked penetration)	1200.0
2 (Consistency of the grease at 25±0.5°C: 60 strokes)	1200.0
3 (Free alkalinity, percent by mass)	1200.0

311

CUSTOM - GOLD CONTENT (% by mass)

GOLD CONTENT (% by mass)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Gold % by mass)	2000.0

312

IS 9537 ( Part 3) (1983) - Specification for conduits for electrical installations ( Part 3) rigid plain conduits of insulating materials.

Specification for conduits for electrical installations ( Part 3) rigid plain conduits of insulating materials.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.0 (ELECTRICAL CHARACTERISTICS:- Insulation Resistance)	2000.0
8.0 (Construction)	1000.0
12. (ELECTRICAL CHARACTERISTICS:- Electrical Strength)	2000.0
11.0 (Resistance to Burning)	5000.0
6.2 (Durability of Marking)	1000.0
7.4 (Uniformity of Wall Thickness)	1000.0
-- (--)	-
10. (RESISTANCE TO HEAT)	2000.0

313

IS 14443 (1997) - Polycarbonate sheets - Specification

Polycarbonate sheets - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2.4 Table3 (Weight/Sq.M)	1000.0
3.2.4 Table3 (Light Transmission)	2000.0
3.2.2 (Identification of polymer)	5000.0
3.2.2 (No of layers/Walls)	500.0
3.2.2 (Profile)	500.0
3.2.2 (Surface Texture)	500.0
3.2.3 (Transparency)	500.0
3.2.3 (Colour)	500.0
3.2.4 (Flame Retardancy)	5000.0
Firm's request (Thickness)	1000.0
Firm's request (Density)	1000.0
Firm's request (Water Absorption, %)	1000.0

314

MMDTS19041 REV-02 DATE 01.01.2024 - -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 4 Table 1 Sr No 1 (Drying timeat25±2˚C a. Surface dry, max IS:101-86 (Part3/Sec.1), Reaffirmed 2017 or latest)	250.0
Cl 4 Table 1 Sr No 1 (Drying time at2 5±2˚C b) Curing time IS:101-86 (Part3/Sec.1), Reaffirmed 2017 or latest)	250.0
Cl 4 Table 1 Sr No 2 (Consistency IS:101-89 (Part1/Sec.5), Reaffirmed 2019 or latest)	250.0
Cl 4 Table 1 Sr No 3 (Finish IS:101-87 (Part 3/Sec.4), Reaffirmed 2019 or latest)	250.0
Cl 4 Table 1 Sr No 4 (Colour IS:101-89 (Part 4/Sec.2), Reaffirmed 2021 or latest)	100.0
Cl 4 Table 1 Sr No 5 (Dry film thickness per coat, by Spray /dipping roller/wipes IS:101-89 (Part3/Sec.2 ) Reaffirmed 2019 or latest version ASTM D7091 (latest version)/by DFT gauge)	250.0
Cl 4 Table 1 Sr No 7 (a )Scratch hardness(at1.5 Kg. load) IS:101-88 (Part5/Sec.2), Reaffirmed 2014 or Latest Version b)Pencil Hardness test ASTM D3363 or Latest Version)	3500.0
Cl 4 Table 1 Sr No 8 (Flexibility & Adhesion (6.25 mm mandrel) IS:101-88 (Part5/Sec.2),Reaffirmed 2014 or Latest Version)	250.0
Cl 4 Table 1 Sr No 9 (Flash Point deg C IS: 101-87(Part 1/ Sec.6),Reaffirmed 2019 or latest version)	250.0
Cl 4 Table 1 Sr No 10 (Resistance to salt spray For 3000 hours ASTM B-117/2019 or latest version)	125000.0
Cl 4 Table 1 Sr No 11 (Protection against Corrosion under condition of Condensation for 2500 hours IS:101-88(Part6/Sec.1),Reaffirmed 2015 or latest)	100000.0
Cl 4 Table 1 Sr No 13 (Spreading & Covering surface area Capacity, .@ DFT ≥5microns Appendix-I of RDSO specification no. M&C/ PCN 100/ 2018)	500.0
Cl 4 Table 1 Sr No 14 (Resistance to chemicals For 24 hours 1) 25% caustic soda solution (w/v) 2) 30% (V/V) H2SO4 IS:101-89 (Part7 /Sec.2) RA 2020 or latest)	2000.0
Cl 4 Table 1 Sr No 15 (Mass in kg/ 10litres, IS:101-87 (Part1/Sec.7)Reaffirmed 2020 or latest)	500.0
Cl 4 Table 1 Sr No 16 (Impact resistance test height 31 Inch, load 6.45pound (200 Inch pound load ASTM2794-93 or latest)	2000.0
Cl 4 Table 1 Sr No 17 (Resistance to tap Water or raw water for 3000 hours IS: 101-90 (Part7/Sec.2) Reaffirmed- 2005 or latest)	7500.0
Cl 4 Table 1 Sr No 18 (Abrasion Resistance test 1000 cycle with CS-17 wheel & 1 kg load ASTMD-4060 or latest)	2500.0
Cl 4 Table 1 Sr No 19 (Glossat60 angle of incidence IS:101-88 (Part 4/ Sec.4) Reaffirmed-2020 or latest)	1500.0
Cl 4 Table 1 Sr No20 (Anti-graffiti properties ASTM D-6578/ 13 /(latest version) Marker:Edding 3000)	7500.0
Cl 4 Table 1 Sr No 21 (Durability Test– Accelerated weathering test: QUV 4 hours and 4 hours Condensation alternatively, (750hrs), Temp. 50 O C as per ASTM G154-or latest)	25000.0

315

Meter Box Test as per customer requirement

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Material Identification)	4000.0
10 (Protection Against Electric shock)	2000.0
13 (Protection against ingress of solid object (IP5X))	6000.0
13 (Protection against harmfull ingress of water (IPX5))	6000.0
18 (Glow wire test @ 650 Deg C (Resistance to heat and fire))	5000.0
19 (Resistance to tracking)	5000.0
20 (Resistant to corrosion)	5000.0
8 (Boiling Water)	2000.0
9 (Tensile strength)	2000.0
10 (Flexural strength)	2000.0
11 (Modulus of Elasticity)	2000.0

316

IS 2141 (2000) - Hot dip galvanized stay strand - Specification (Fourth Revision)

Hot dip galvanized stay strand - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Sulphur)	500.0
4 (Phosphorus)	500.0
6.2 (Breaking Force of Single Wire)	2000.0
7 (Freedom from defect)	1000.0
8.1 (Wrapping Test of wire)	1000.0
9.1 (Breaking Force of Strand)	3000.0
9.1 (Elongation of Strand)	1000.0
8.1 (Wire Diameter)	1000.0
9.2 (Mass of Zinc Coating)	2000.0

317

IS 398 Part 2 (2025) - ALUMINIUM CONDUCTORS FOR OVERHEAD TRANSMISSION PURPOSES

ALUMINIUM CONDUCTORS FOR OVERHEAD TRANSMISSION PURPOSES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Direction of Lay)	1000.0
3.3 (Measurement of Diameter of individual Aluminum Wires)	3500.0
13.2 (Measurement of Diameter of Galvanized Steel Wires)	1000.0
13.3 (Breaking Load Test of Wire)	7000.0
13.4 (Ductility Test)	1000.0
13.5 (Wrapping Test for Aluminum Wire)	1000.0
13.6 (Resistance Test)	2000.0
13.7 (Galvanizing Test)	2000.0
13.8 (Lay Ratio)	1000.0
7.1 (Freedom from defect)	1000.0
9.2 (Joints in Aluminium Stranded Wires (Visual Examination))	1000.0
Annexure A-3 & Table 3 (Approximate breaking load of conductors)	2000.0

318

IS 10647 (1983) - Specification for wheel bearing grease

Specification for wheel bearing grease

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.3 (Consistency of the grease at 25+/- 0.5 degree C, 60 strokes)	1200.0
2.3 (Drop Point)	1200.0
2.3 (Copper strip corrosion test at 100 degree C for 24 hours)	1200.0
2.3 (Water Content)	1200.0
2.3 (consistency of grease, 25+/- 0.5 degree, unworked penetration)	1200.0
2.3 (consistency of grease, 25+/- 0.5 degree, 10000 strokes)	1200.0

319

IS 9537 : Part 3 (1983) - Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Resistance to Burning)	5000.0
10 (Resistance to Heat)	2000.0
9.5 (Collapse Test)	2000.0
9.4 (Impact Test)	2000.0
9.3 (Compression Test)	2000.0
9.2 (Bending Test)	2000.0
8 (Construction)	1000.0
7.4 (Uniformity of Wall Thickness)	1000.0
- (-)	-
9.4 (Visual)	1000.0
6.4 (Durability of Marking)	500.0

320

ASME BPVC Section V SE 165 - Standard Practice for Liquid Penetrant Examination for General Industry

Standard Practice for Liquid Penetrant Examination for General Industry

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Flaw detection by Liquid Penetrant Test)	1000.0

321

ASME BPVC Section V SD 7091 - Standard practice for Non-destructive measurement of Dry Film Thickness of Non-magnetic Coating applied to ferrous metals and Non-magnetic, Non-conductive coating applied to Non-ferrous Metals

Standard practice for Non-destructive measurement of Dry Film Thickness of Non-magnetic Coating applied to ferrous metals and Non-magnetic, Non-conductive coating applied to Non-ferrous Metals

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dry Film Thickness)	2000.0

322

IS 13043 (1991) - Covered manual metal arc welding electrodes - Determination of efficiency, metal recovery and deposition co - Efficien

Covered manual metal arc welding electrodes - Determination of efficiency, metal recovery and deposition co - Efficien

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Metal Recovery Test-Effective Electrode Efficiency)	3000.0

323

IS 11802 (1986) - Methods for determination of diffusible hydrogen content of deposited weld metal from covered electrodes in welding mild and low alloy steels

Methods for determination of diffusible hydrogen content of deposited weld metal from covered electrodes in welding mild and low alloy steels

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Volume of diffusible hydrogen)	5000.0

324

IS 1608 (Part1): 2022 - Metallic Materials-Tensile Testing-Method of Test at Room Temperature

Metallic Materials-Tensile Testing-Method of Test at Room Temperature

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Tensile Testing)	5000.0

325

IS 1757 (PART 1): 2020 - Metallic Materials Charpy Pendulum Impact Test Part 1 Test Method

Metallic Materials Charpy Pendulum Impact Test Part 1 Test Method

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Charpy Impact Test)	3000.0
2 (Charpy Impact Test)	5000.0

326

IS 1757 Part 1 (2020) - Metallic Materials — Charpy Pendulum Impact Test Part 1 Test Method ( Fourth Revision )

Metallic Materials — Charpy Pendulum Impact Test Part 1 Test Method ( Fourth Revision )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Impact Test with sample preparation)	5000.0
9 (Impact Test without sample preparation)	4000.0

327

IS 3600 : Part 5 (2018) - Method of testing fusion welded joints and weld metal in steel: Part 5 destructive tests on welds in metallic materials - Bend tests (Third Revision)

Method of testing fusion welded joints and weld metal in steel: Part 5 destructive tests on welds in metallic materials - Bend tests (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (TRANSVERSE ROOT or FACE BEND TEST)	1000.0

328

IS 3848:1981 - Method for end quench test for hardenability of steel (First Revision)

Method for end quench test for hardenability of steel (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Hardenability Test)	8000.0

329

IS 6416:2022 - Methods for Measuring Case Depth of Steel

Methods for Measuring Case Depth of Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Case Depth of Steel by Macrostructure Method)	3000.0
8 (Case Depth of Steel by Microstructure Method)	3000.0

330

ASTM E114-20 - Standard Practice for Ultrasonic Pulse-Echo Straight Beam Contact Testing

Standard Practice for Ultrasonic Pulse-Echo Straight Beam Contact Testing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Ultrasonic Pulse-Echo Straight Beam Contact Testing)	1000.0