NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1274 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

271

Custom Food Grade Epoxy Paint (2024) - Custom Food Grade Epoxy Paint

Custom Food Grade Epoxy Paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Adhesion (Mpa))	2500.0
2 (Specific gravity Comp. A & Comp. B)	2400.0
3 (Pot life)	1200.0
4 (Solid Content)	1200.0
5 (Color)	1200.0
6 (Chemical Resistance (All Test))	7500.0
7 (Drinking Water Performance Test for Heavy metals)	10000.0
8 (Dry film Thickness per coat (microns))	1200.0

272

CUSTOM PAINT IS 2024 NTH 03 (2024) - CUSTOM PAINT IS 2024 NTH 03

CUSTOM PAINT IS 2024 NTH 03

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (colour)	1200.0
2 (Viscosity (in Poise))	1200.0
3 (Flash Point (in Deg.C))	1200.0
4 (Specific Gravity)	1200.0
5 (Drying Time (Touch Dry))	1200.0
6 (Finish)	1200.0
7 (Pigment Content (%))	1200.0
8 (Volatile matter (%))	1200.0
9 (Volume solid (%))	2000.0
10 (Mass Solid (% by Weight))	1200.0
11 (Adhesion (Cross Cut))	3000.0

273

CUSTOM PAINT IS 2024 NTH 02 (2024) - CUSTOM PAINT IS 2024 NTH 02

CUSTOM PAINT IS 2024 NTH 02

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (color)	1200.0
2 (Viscosity)	1200.0
3 (Pot life)	1500.0
4 (Flash Point)	1200.0
5 (Specific gravity (Base))	1200.0
6 (Specific gravity (Hardener))	1200.0
7 (Specific gravity (Mix))	1200.0
8 (Drying time (Surface dry))	1200.0
9 (Drying time (Hard dry))	1200.0
10 (Fineness of Grind)	1200.0
11 (Pigment content(%))	1200.0
12 (Volatile Matter (%))	1200.0
13 (Volume Solids (%))	2000.0
14 (Mass solid (%))	1200.0
15 (TABER ABRASION RESINTANCE- ASTM D4060 - CS 17, 1000 GMS 1000 CYCLE)	5000.0
16 (Adhesion Cross Cut)	3000.0
17 (Resistance to Salt Spray 500 Hours)	25000.0
18 (Flexibility/ Bend Test)	1200.0
19 (Impact Test)	1500.0
20 (Scratch Hardness)	1200.0
21 (Water Immersion 2000hrs)	3500.0
22 (Consistency)	1200.0
23 (Finish)	1200.0

274

CUSTOM PAINT IS 2024 NTH 01 - CUSTOM PAINT IS 2024 NTH 01

CUSTOM PAINT IS 2024 NTH 01

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Total Non Volatile Vehicle Content)	1200.0
2 (Pigment Content (Pigmentation in Mixed Paint))	1200.0
3 (Application Properties)	1200.0
4 (Drying time 1) Surface dry 2) Hard Dry)	2400.0
5 (color)	1200.0
6 (Finish)	1200.0
7 (Finish)	1200.0
8 (Flexibility & Adhesion (Bend Test))	1200.0
9 (Impact Test (1m height))	1500.0
10 (Flash Point Deg.C)	1200.0
11 (Pot Life)	1500.0
12 (Resistance to sea water)	2000.0
13 (Resistance to Kerosene)	1500.0
14 (Taber Abrasion)	5000.0
15 (Resistance to Thermal Shock)	2000.0
16 (Resistance to Accelerated Weathering)	50000.0

275

C-9809(Rev. 4) (2009) - SPECIFICATION FOR NON-ASBESTOS BASED 'K' TYPE HIGH FRICTION COMPOSITE BRAKE BWCKS FOR COACHES WITH BOGIE MOUNTED BRAKE SYSTEM ON INDIAN RAILWAYS

SPECIFICATION FOR NON-ASBESTOS BASED 'K' TYPE HIGH FRICTION COMPOSITE BRAKE BWCKS FOR COACHES WITH BOGIE MOUNTED BRAKE SYSTEM ON INDIAN RAILWAYS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Density)	1000.0
4.2 (Ash Contents)	2000.0
4.2 (Acetone extract)	2000.0
4.2 (Cross breaking strength)	2000.0

276

IS 11149 (1984) - Specification for rubber gaskets

Specification for rubber gaskets

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 1,2,3 & 4 (Hardness)	1000.0
Table 1,2,3 & 4 (Tensile Strength)	2000.0
Table 1,2,3 & 4 (Ultimate elongation)	1000.0
Table 1,2,3 & 4 (Compression set)	2000.0
4.3,5.3,6.3 & 7.3 (Accelerated Ageing)	4000.0
4.4 (Water absorption)	2000.0
6.4 & 7.4 (Ageing in Oil)	4000.0
6.5 (Ageing in Iso-Octane)	4000.0

277

CUSTOM/GEOSTRAP/2024 - CUSTOM/GEOSTRAP/2024

CUSTOM/GEOSTRAP/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Ultimate Tensile Strength)	5000.0
2.0 (Chemical resistance, strength retained after 72 hrs. immersion)	5000.0
3.0 (Width)	1000.0
4.0 (Roll Length)	1000.0

278

IS 1145 -1980 (Reaffirmed 2003) - SPECIFICATION FOR LEAD-ACID STORAGE BATTERIES FOR MOTOR CYCLES, AUTORICKSHAWS AND SIMILAR VEHICLES

SPECIFICATION FOR LEAD-ACID STORAGE BATTERIES FOR MOTOR CYCLES, AUTORICKSHAWS AND SIMILAR VEHICLES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.8 (Dimension)	1000.0
7.6 (Physical Examination)	1000.0
7.9 (Air Pressure Test)	10000.0
7.12 (High Rate Discharge Test)	15000.0
7.15 (Life Test)	20000.0
7.14 (Resistance to Overcharge Test)	5000.0
7.13 (Retention of Charge Test)	5000.0
7.10 (Test for Capacity)	20000.0
7.11 (Vibration Test)	10000.0
7.16 or 7.17 (Storage Test)	15000.0

279

14255 (1995) - Aerial Bunched Cables for working voltages up to and including 1100 Volts-Reaffirmed 2020 specification

Aerial Bunched Cables for working voltages up to and including 1100 Volts-Reaffirmed 2020 specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 sl no 1(a)(i), 10.2 (a) (Tensile Test on phase/ street light conductor)	1000.0
10.1 sl no 1(a)(ii), 10.2 (b) (Wrapping Test on phase/ street light conductor)	500.0
10.1 sl no 1(a)(iii) (Resistance Test on phase/ street light conductor)	2000.0
10.1 sl no 1(b)(i) ,10.2 sl no(c) (Test on messenger conductor Breaking load)	1000.0
10.1 sl no 1(b)(ii), 10.2 (d) (Test on messenger conductor Elongation test)	1500.0
10.1 sl no 1(c)(i),10.2 (g) (Physical test for XLPE insulation Tensile strength and elongation at break)	1500.0
10.1 sl no 1(c)(ii) (Physical test for XLPE insulation Ageing in air oven)	2000.0
10.1 sl no 1(c)(iii),10.2(h) (Physical test for XLPE insulation Hot set test)	2000.0
10.1 sl no 1(c)(iv) (Physical test for XLPE insulation Shrinkage)	1000.0
10.1 sl no 1(c)(v) (Physical test for XLPE insulation Water absorption test)	1000.0
10.1 sl no 1(d)(i) (Physical test for PE insulation Tensile strength and elongation at break)	1500.0
10.1 sl no 1(d)(ii) (Physical test for PE insulation Melt flow index)	1000.0
10.1 sl no 1(d)(iv) (Physical test for PE insulation Vicat softening point)	1000.0
10.1 sl no 1(d)(v) (Physical test for PE insulation Environment stress cracking)	1500.0
10.1 sl no 1(e),10.2(f) (Test for thickness of insulation)	1500.0
10.1 sl no 1(f),10.2(j) (Insulation resistance (Volume Resistivity) test)	1500.0
10.1 sl no 1(g),10.2(k) (High Voltage test)	1500.0
10.2 (e) (Conductor resistance test)	2000.0
Test on 2nd core (Test on 2nd core)	2000.0
Test on 3rd core (Test on 3rd core)	2000.0
Test on 4th core (Test on 4th core)	2000.0
10.1 sl no 1(a)(i), 10.2 (a) (Tensile Test on phase/ street light conductor)	1000.0
10.1 sl no 1(a)(ii), 10.2 (b) (Wrapping Test on phase/ street light conductor)	500.0
10.1 sl no 1(a)(iii) (Resistance Test on phase/ street light conductor)	2000.0
10.1 sl no 1(b)(i) ,10.2 sl no(c) (Test on messenger conductor Breaking load)	1000.0
10.1 sl no 1(b)(ii), 10.2 (d) (Test on messenger conductor Elongation test)	1500.0
10.1 sl no 1(c)(i),10.2 (g) (Physical test for XLPE insulation Tensile strength and elongation at break)	1500.0
10.1 sl no 1(c)(ii) (Physical test for XLPE insulation Ageing in air oven)	2000.0
10.1 sl no 1(c)(iii),10.2(h) (Physical test for XLPE insulation Hot set test)	2000.0
10.1 sl no 1(c)(iv) (Physical test for XLPE insulation Shrinkage)	1000.0
10.1 sl no 1(c)(v) (Physical test for XLPE insulation Water absorption test)	1000.0
10.1 sl no 1(d)(i) (Physical test for PE insulation Tensile strength and elongation at break)	1500.0
10.1 sl no 1(d)(ii) (Physical test for PE insulation Melt flow index)	1000.0
10.1 sl no 1(d)(iv) (Physical test for PE insulation Vicat softening point)	1000.0
10.1 sl no 1(d)(v) (Physical test for PE insulation Environment stress cracking)	1500.0
10.1 sl no 1(e),10.2(f) (Test for thickness of insulation)	1500.0
10.1 sl no 1(f),10.2(j) (Insulation resistance (Volume Resistivity) test)	1500.0
10.1 sl no 1(g),10.2(k) (High Voltage test)	1500.0
10.2 (e) (Conductor resistance test)	2000.0
Test on 2nd core (Test on 2nd core)	2000.0
Test on 3rd core (Test on 3rd core)	2000.0
Test on 4th core (Test on 4th core)	2000.0
10.1 sl no 1(a)(i), 10.2 (a) (Tensile Test on phase/ street light conductor)	1000.0
10.1 sl no 1(a)(ii), 10.2 (b) (Wrapping Test on phase/ street light conductor)	500.0
10.1 sl no 1(a)(iii) (Resistance Test on phase/ street light conductor)	2000.0
10.1 sl no 1(b)(i) ,10.2 sl no(c) (Test on messenger conductor Breaking load)	1000.0
10.1 sl no 1(b)(ii), 10.2 (d) (Test on messenger conductor Elongation test)	1500.0
10.1 sl no 1(c)(i),10.2 (g) (Physical test for XLPE insulation Tensile strength and elongation at break)	1500.0
10.1 sl no 1(c)(ii) (Physical test for XLPE insulation Ageing in air oven)	2000.0
10.1 sl no 1(c)(iii),10.2(h) (Physical test for XLPE insulation Hot set test)	2000.0
10.1 sl no 1(c)(iv) (Physical test for XLPE insulation Shrinkage)	1000.0
10.1 sl no 1(c)(v) (Physical test for XLPE insulation Water absorption test)	1000.0
10.1 sl no 1(d)(i) (Physical test for PE insulation Tensile strength and elongation at break)	1500.0
10.1 sl no 1(d)(ii) (Physical test for PE insulation Melt flow index)	1000.0
10.1 sl no 1(d)(iv) (Physical test for PE insulation Vicat softening point)	1000.0
10.1 sl no 1(d)(v) (Physical test for PE insulation Environment stress cracking)	1500.0
10.1 sl no 1(e),10.2(f) (Test for thickness of insulation)	1500.0
10.1 sl no 1(f),10.2(j) (Insulation resistance (Volume Resistivity) test)	1500.0
10.1 sl no 1(g),10.2(k) (High Voltage test)	1500.0
10.2 (e) (Conductor resistance test)	2000.0
Test on 2nd core (Test on 2nd core)	2000.0
Test on 3rd core (Test on 3rd core)	2000.0
Test on 4th core (Test on 4th core)	2000.0
10.1 sl no 1(b)(iii) (Resistance test on messenger conductor)	1000.0

280

RDSO STR No. C-K105 (Rev. 1) (2014) - Schedule of Technical Requirements for Bolster Suspension Hangers of BG & MG Mainline and EMU/DMU/MEMU Coaches

Schedule of Technical Requirements for Bolster Suspension Hangers of BG & MG Mainline and EMU/DMU/MEMU Coaches

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (S. No. 1) (Visual Inspection)	1000.0
5.1 (S. No. 3) (Hardness)	4000.0
5.1 (S. No. 4) (Proof Load)	6000.0
5.1 (S. No. 7) (Carbon)	500.0
5.1 (S. No. 7) (Silicon)	500.0
5.1 (S. No. 7) (Manganese)	500.0
5.1 (S. No. 7) (Sulphur)	500.0
5.1 (S. No. 7) (Phosphorus)	500.0
5.1 (S. No. 7) (Chemical Composition (as per Cl. 6.3 of IS: 1875-1992))	2500.0

281

Specification for LED Based Flasher Light - Specification for LED Based Flasher Light

Specification for LED Based Flasher Light

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Voltage surge test. 1.8 kV as per IEC 61000-4-5)	5000.0
2 (Damp Heat Test as per IEC 60571-2012)	15000.0
3 (Dry heat test as per ELRS/SPEC/LFL/0017 (Rev-I, Sep 2024) Cl no. 6.10.5)	10000.0
4 (Cooling test as per ELRS/SPEC/LFL/0017 (Rev-I, Sep 2024) Cl no. 6.10.7)	10000.0
5 (Water Ingress test, IP 65 of lamp unit as per IS 10322 : Part 1 (2014))	12000.0
6 (Burn in Test as per ELRS/SPEC/LFL/0017 (Rev-I, Sep 2024) Annexure-2)	15000.0

282

28681 (2024) - Chopped steel Wool Fiber

Chopped steel Wool Fiber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Tap bulk density 50 gms sample /10 min or 250 taps)	1200.0
3 (Specific Gravity)	1200.0
4 (Micro Structure)	3000.0
5 (Chemical Composition (C,Mn,Si, P & S))	2500.0
6 (Appearance)	1200.0
1 (Acetone Extract)	2500.0

283

IS 2026 : Part 11 (2021) - Power Transformers Part 11 Dry-Type Transformers

Power Transformers Part 11 Dry-Type Transformers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl No 14.2.5 (Applied Voltage Test)	2500.0
14.2.6 (Induced Voltage Withstand Test)	4000.0
14.2.4 (Measurement of No Load Loss & Current)	6000.0
14.2.3 (Measurement of Short Circuit Impedance and Load Loss)	8000.0
14.2.2 (Measurement of Voltage Ratio and Check of phase Displacement)	2000.0
14.2.1 (Measurement of Winding Resistance)	1000.0
14.3.2 (Temperature Rise Test)	40000.0
Cl. 21.2(e) of IS 1180 (Part 1) (Measurement of Insulation resistance)	1500.0

284

IS 2026 : Part 1 (2011) - Power Transformers: Part 1 General (Second Revision)

Power Transformers: Part 1 General (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1.2(a) (Temp Rise)	20000.0
10.1) c ) (Loss % Impedence)	20000.0
10.1.1(d) (Loss Current)	12800.0
10.1.3(g) (Measurement of Hormonices of the no load current)	10000.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
10.1.1(b) (Measurement of Voltage ratio & voltage vec,tor group test)	3200.0
10.1.1(a) (Measurement of windlng Resistance)	1600.0
10.1.3(d) (Measurement of Zero phase sequence impedance for 3 Phase transformer)	3000.0
10.1.1(e) (Separate source AC voltage withstand test)	4000.0
10.1.3(g) (% Harmonics)	10000.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
10.1.1(b) (Voltage ratio & Phase Displacement)	3200.0
10.1.1(a) (Windlng Resistance)	1600.0
10.1.3(d) (Zero Sequence Impedance)	3000.0
10.1.1(e) (AC voltage withstand test)	4000.0
10.1.1(e) (Induced Overvoltage)	6400.0
10.1.1(d) (No Load loss and current)	9600.0
10.1.1 (C) (% impedance and load loss)	12800.0
10.1.2(a) (Temperatur Rise)	20000.0
10.1.3 (f) (Noise Level)	10000.0
17.3.2 (b) of CBIP Pub. No. 317 (Oil Leakage Test (Pressure Test - Type))	10000.0
17.3.1 (a) of CBIP Pub. No. 317 (Pressure Test Routine (Deflection))	8000.0
17.3.2 (a) of CBIP Pub. No. 317 (Vacuum Test - Type (Deflection))	10000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	3000.0
CBIP Publication no. 317 (Polarization Index Test)	2500.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0

285

CUSTOM - COPPER ALLOY

COPPER ALLOY

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Copper, percent by mass)	1200.0
2 (Lead, Percent by mass)	1200.0
3 (Zinc)	1200.0

286

Portable LED Light Tower - Portable LED Light Tower

Portable LED Light Tower

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A (Dimensions)	5000.0
B (Telescopic Tower Mast Detail (Construction))	5000.0
C (LED Luminaire)	57000.0
D (Driver)	40000.0
E (General Set Up Parameters)	10000.0
F (Photometric Parameters of System)	10000.0
G (Accessories and Packing)	2000.0
H (Genset Details)	35000.0

287

Custom Mechanical Gauges-Dimension - Custom Mechanical Gauges dimension as per drg.

Custom Mechanical Gauges dimension as per drg.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimensions as per customer request)	2000.0

288

CUSTOM/COMPOSITE STRAP/2024 - CUSTOM/COMPOSITE STRAP/2024

CUSTOM/COMPOSITE STRAP/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Tensile Strength)	2000.0
2.0 (Elongation)	1000.0
3.0 (System Breaking Strength (Strap + Buckles))	2000.0
4.0 (Width of the Strap)	1000.0
5.0 (Thickness of the Strap)	1000.0
6.0 (Linear Breaking Strength)	2000.0
Firm's request (Breaking Strength)	2000.0

289

1264:1997 - Brass Gravity Die Castings

Brass Gravity Die Castings

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Copper)	1200.0
7.1 (Tin)	1200.0
7.1 (Lead)	1200.0
7.1 (Nickel)	1200.0
7.1 (Iron)	1200.0
7.1 (Aluminium)	1200.0
7.1 (Manganese)	1200.0
7.1 (Silicon)	1200.0

290

IS 17682 (2021) - ALUMINIUM COMPOSITE PANEL

ALUMINIUM COMPOSITE PANEL

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Tensile strength)	1000.0
7.1 (Yield strength)	1000.0
7.1 (% Elongation)	1000.0
7.1 (Density of Core (As per IS 13360 Part-3/Sec 10 or Sec 11))	1000.0
6 (Dimension)	1000.0
7.1 (Coating Thickness on aluminium sheet)	2000.0

291

IS 17682 (2021) - ALUMINIUM COMPOSITE PANEL SPECIFICATION

ALUMINIUM COMPOSITE PANEL SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

292

IS 11084 (2023) - Silver Palladium Alloy Wire and Strip for Electrical Contacts

Silver Palladium Alloy Wire and Strip for Electrical Contacts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.4 (Tensile Strength)	2000.0
6.4 (% Elongation)	1000.0
6.4 (Vickers Hardness)	2000.0
6.4 (Reverse Bend Test)	1500.0
6.2 (Freedom from defects)	1000.0

293

IS 13620 (1993) - Fusion Bonded Epoxy Coated Reinforcing Bars -

Fusion Bonded Epoxy Coated Reinforcing Bars -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A-5 (Pull-out test)	20000.0
7.1 (Coating Thickness)	1500.0
7.3 (Adhesion of Coating)	2000.0
A-7 (Impact Test - Resistance of Coating)	1500.0

294

Custom - Modified Bitumen

Modified Bitumen

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Softening point)	1200.0
2 (Penetration)	1200.0

295

15041:2001 (RA 2024) - Textiles – Flat woven webbing slings made of man-made fibres for general services

Textiles – Flat woven webbing slings made of man-made fibres for general services

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.28 (Safe Working Load)	3000.0
3.28 (Safe Working Load)	6000.0
3.28 (Safe Working Load)	8000.0
3.28 (Safe Working Load)	10000.0
5.4 (Proof Load)	3000.0
5.4 (Proof Load)	5000.0
5.4 (Proof Load)	8000.0
5.4 (Proof Load)	10000.0

296

IS 1838 : Part 3 (2011) - Preformed Fillers for Expansion Joints in Concrete Pavements and Structures(non-extruding and resilient type) Part 3 Polymer Based

Preformed Fillers for Expansion Joints in Concrete Pavements and Structures(non-extruding and resilient type) Part 3 Polymer Based

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.0 (Dimensions)	1000.0
6.0 (Resistance to handling)	1000.0
6.0 (Recovery)	1000.0
6.0 (Compression)	1000.0
6.0 (Extrusion)	1000.0
6.0 (Water Absorption)	1000.0
6.0 (Density)	1000.0
6.0 (Weathering)	5000.0

297

IS 17875 (2022) - Stainless Steel Seamless Pipes and Tubes for General Services

Stainless Steel Seamless Pipes and Tubes for General Services

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 (Tensile Strength)	1000.0
10.1 (Yield Strength)	1000.0
10.1 (Percent Elongation)	1000.0
23 (Outside Diameter)	500.0
21 (Workmanship, Finish, and Appearance)	1000.0
12 (HARDNESS TEST FOR TUBES)	2000.0
13 (FLARING TEST (FOR TUBES ONLY))	1500.0
23 (Wall Thickness)	500.0
15 (Micro Structure Austenitic Grain Size)	3000.0
17 (Hydraulic Pressure Test)	5000.0
18 (Inter-Granular Corrosion Test)	10000.0
8 (Chemical Composition)	5000.0
8.1 & 8.2 (Carbon) (Carbon (as C))	1000.0
8.1 & 8.2 (Manganese) (Manganese (as Mn))	1000.0
8.1 & 8.2 (Silicon) (Silicon (as Si))	1000.0
8.1 & 8.2 (Nickel) (Nickel (as Ni))	1000.0
8.1 & 8.2 (Chromium) (Chromium (as Cr))	1000.0
8.1 & 8.2 (Molybdenum) (Molybdenum (as Mo))	1000.0
8.1 & 8.2 (Sulphur) (Sulphur (as S))	1000.0
8.1 & 8.2 (Phosphorus) (Phosphorus (as P))	1000.0
8.1 & 8.2 (Copper) (Copper (as Cu))	500.0
8.1 & 8.2 (Nitrogen) (Nitrogen (as N))	500.0
8 (CHEMICAL COMPOSITION, C,Si,Mn,Ni,Cr, Mo, S,P,N,Cu ,Others)	5000.0

298

Custom/Paint-RPPT/2024 (2024) - Custom/Paint-RPPT/2024

Custom/Paint-RPPT/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Tensile Strength)	2000.0
2.0 (Elongation)	1000.0
3.0 (Hardness(Shore A))	1000.0
4.0 (Water Absorption)	2000.0
5.0 (Adhesion Test on Concrete)	1200.0
6.0 (Viscosity (Brookfield))	1200.0
7.0 (Dry Film Material Softening Point)	2000.0
8.0 (Specific gravity)	1500.0
9.0 (Solid Content)	1200.0
12 (Solid by weight %)	1200.0
11 (Touch drying time)	1200.0
13 (Moisture vapour transmission, g/sq.m/24 hrs)	5000.0
10 (Density, gm/cc)	1200.0
14 (Accelerated Weathering Test QUV, 500 hours.)	25000.0

299

IS 14252 (2015) - Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Ash Content)	2000.0
4 (Avg. Breaking Strength of fabric after UV exposure)	2000.0
4 (Elongation at break of fabric, Widthwise)	500.0
4 (Elongation at break of fabric, Lengthwise)	500.0
4 (Average Breaking Strength of bottom seam)	2000.0
4 (Avg. Breaking Strength of fabric, Widthwise)	1000.0
4 (Avg. Breaking Strength of fabric, Lengthwise)	1000.0
4 (Mass of Sack (without tying cord))	1000.0
4 (Picks/dm)	500.0
4 (Ends/dm)	500.0
4 (Dimensions, Outside Width)	500.0
4 (Dimensions, Outside Length)	500.0
4 (Mass of Bale)	2000.0
3.4.1 (Mouth of Sack, Channel secured with )	2000.0
3.4.1 (Mouth of Sack, Channel withturn-in)	2000.0
3.3 (Tying cord Material Identification)	2000.0
3.4.1 (Mouth of Sack, Channel width)	2000.0
3.4.1 (Bottom Seam, Number of Stitchs per dm)	2000.0
3.4.1 (Bottom Seam, Double fold seam depth)	2000.0
3.4.1 (Bottom Seam, Outer stitch distance from outer edge)	2000.0
3.4.1 (Bottom Seam, Two row separation distance)	2000.0
4 (UV - Resistance Test (192 hrs.))	9600.0
4 (GSM of Fabrics)	1000.0

300

IS 3181 (2025) - Conveyor Belts - Fire Resistant Conveyor Belting for Underground Mines and Such other Hazardous Applications - Specification (IS 3181: 2025 )

Conveyor Belts - Fire Resistant Conveyor Belting for Underground Mines and Such other Hazardous Applications - Specification (IS 3181: 2025 )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.0 (Belt Thickness)	1000.0
7.0 (Carcass Thickness)	1000.0
8.0 (Cover Thickness)	1000.0
12, Table 1 (Full Thickness Tensile Strength, N/mm Width)	5000.0
12.0, Table 1 (Full Thickness Elongation at Break, %)	2000.0
12.2 (Elongation at Reference Load, % (Longitudinal direction))	1000.0
13.0, Table 1 (Tear Strength, kN)	4000.0
14.0, Table-7 (Adhesion between Cover and Carcass, kN/m)	2000.0
14.0, Table-7 (Adhesion between Adjacent Plies, kN/m)	3000.0