| 181 |
RDSO Specification No. M&C/PCN/100/2018 - POLYURETHANE SURFACER (TWOPACK) |
POLYURETHANE SURFACER (TWOPACK) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Drying time
a) Surface dry
b) Hard dry
c) Hard dry at 70°C) |
3600.0 |
|
| 2 (Consistency) |
1200.0 |
|
| 3 (Finish) |
1200.0 |
|
| 4 (Colour) |
1200.0 |
|
| 5 (Dry film thickness) |
1200.0 |
|
| 6 (Volume solids, %) |
2000.0 |
|
| 7 (Scratch hardness (1.5Kg Load)) |
1200.0 |
|
| 9 (Flashpoint
a) Component ‘A’
b) Component ‘B’) |
2400.0 |
|
| 10 (Fineness of Grind) |
1200.0 |
|
| 11 (Pot life (After induction time)
i) 27±2°C
ii) 40±2°C) |
1500.0 |
|
| 12 (Mass in Kg/10 litres) |
1200.0 |
|
| 13 (Keeping properties) |
2000.0 |
|
| 14 (Theoretical spreading rate) |
2000.0 |
|
| 15 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix of two components at 27± 2 °C in Supply condition) |
1200.0 |
|
|
| 182 |
RDSO SPECIFICATION M&C/PCN/100/2018 PUTTY - UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK) |
UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Drying time:
a)Surface dry
b) Hard dry
c)Hard dry time at 70 Deg. C) |
3600.0 |
|
| 2 (Consistency) |
1200.0 |
|
| 3 (Stopping properties) |
2000.0 |
|
| 4 (Rubbing properties) |
2000.0 |
|
| 5 (Hold out Property) |
2000.0 |
|
| 6 (Adhesion & Compatibility of Paint System) |
2000.0 |
|
| 7 (Pot life ,at 27±2 Deg. C) |
1500.0 |
|
| 8 (% solids) |
1200.0 |
|
| 9 (Keeping properties) |
5000.0 |
|
|
| 183 |
IS 15850 (2009) - Nuclear grade boron carbide - Specification |
Nuclear grade boron carbide - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Clauses 4.2.1 and 4.2.2 (Total Boron In Boron Carbide) |
2000.0 |
|
|
| 184 |
RDSO Specification for Rail Pads Sl. No. T-55-2023 - RDSO Specification for Rail Pads Sl. No. T-55-2023 |
RDSO Specification for Rail Pads Sl. No. T-55-2023 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Weight Test) |
1000.0 |
|
| - (Modulus at 100% Elongation) |
2000.0 |
|
| - (Elongation at Break) |
2000.0 |
|
| - (Tensile Strength) |
2000.0 |
|
| - (Shore hardness) |
1000.0 |
|
| - (Tension Set Subject to 50% Stretch) |
2000.0 |
|
| - (Tensile Strength after ageing at 100±1ºC for 72+0/-2 hrs.) |
3000.0 |
|
| - (Tensile Strength(Retension after ageing)) |
1000.0 |
|
| - (Elongation at Break After ageing at 100±1ºC for 72+(0/-2) hrs) |
3000.0 |
|
| - (Elongation at Break (Retention after ageing)) |
1000.0 |
|
| - (Thickness) |
1000.0 |
|
| - (Specific Gravity) |
1000.0 |
|
| - (Ash Contents) |
2000.0 |
|
| - (Electrical resistance before immersion as per appendix "G") |
2000.0 |
|
| - (Electrical resistance after immersion as per appendix "G") |
3000.0 |
|
| - (Adhesion Strength test) |
2000.0 |
|
|
| 185 |
GFN Liners as per RDSO Specification - GFN Liners as per RDSO Specification [-] |
GFN Liners as per RDSO Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Internal Cavity) |
1000.0 |
|
| - (Water absorption) |
2000.0 |
|
| - (Cross Breaking Load) |
2000.0 |
|
| - (Glass Filler) |
2000.0 |
|
| - (Specific Gravity) |
1000.0 |
|
| - (Dielectric Strength) |
5000.0 |
|
| - (Volume Resistivity) |
3000.0 |
|
|
| 186 |
Customized Specification for Printed Papers/Books - Customized Specification for Printed Papers/Books [-] |
Customized Specification for Printed Papers/Books |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (GSM) |
1000.0 |
|
|
| 187 |
28907 (2021) - CUSTOM SPECIFICATION -IR STD. SPEC SR NO T-31-2021 FOR LADLE ANALYSIS [-] |
CUSTOM SPECIFICATION -IR STD. SPEC SR NO T-31-2021 FOR LADLE ANALYSIS |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.3.1 (Carbon) |
1000.0 |
|
| 4.3.1 (Manganese) |
1000.0 |
|
| 4.3.1 (Silicon) |
1000.0 |
|
| 4.3.1 (Sulphur) |
1000.0 |
|
| 4.3.1 (Phosphorus) |
1000.0 |
|
|
| 188 |
Customized Specification for Fleece Laminated Self adhesive SBS Modified membrane - Customized Specification for Fleece Laminated Self adhesive SBS Modified membrane [-] |
Customized Specification for Fleece Laminated Self adhesive SBS Modified membrane |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Thickness) |
1000.0 |
|
| - (Pressure Head Test) |
2000.0 |
|
| - (Tensile Strength(Longitudinal direction)) |
1000.0 |
|
| - (Tensile Strength(Transversal)) |
1000.0 |
|
| - (Elongation at Break(Longitudinal)) |
1000.0 |
|
| - (Elongation at Break(Transversal)) |
1000.0 |
|
| - (Tear Strength(Longitudinal)) |
1000.0 |
|
| - (Tear Strength(Transversal)) |
1000.0 |
|
| - (Low temperature flexibility) |
2000.0 |
|
| - (Heat Resistance) |
1000.0 |
|
| - (Static Puncture Resistance) |
1000.0 |
|
| - (Softening Point of coating compound) |
1500.0 |
|
| - (Water absorption at 24 hours) |
2000.0 |
|
|
| 189 |
Custom - Concrete - Hardened Concrete Physical & Chemical properties. |
Hardened Concrete Physical & Chemical properties. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8 (Test for compressive strength (3) [IS 516 (Part 4)], N/mm^2) |
15000.0 |
|
| - - (Test for Alkali content (3) [IS 4032 or relevant specification], %) |
3000.0 |
|
| - - (Test for Chloride Content (3) [ IS 4032 or relevant specification], %) |
3000.0 |
|
| -- (Test for sulphate content (3) {is 4032 or relevant specification], %) |
3000.0 |
|
| - - (Test for Sulphate Content [IS 4032 or relevant specification], %) |
2000.0 |
|
| - - (Test for Alkali content (2) [IS 4032 or relevant specification)) |
2000.0 |
|
| - - (Test for Chloride Content (2) [IS 4032 or relevant specification], %) |
2000.0 |
|
| 8 (Equivalent Cube Strength [IS 516 (Part 4)], in N/mm^2) |
5000.0 |
|
| - (Test for Alkali content [IS 4032 / IS 2386], %) |
1000.0 |
|
| - - (Test for Chloride Content [ IS 4032 or relevant IS], %) |
1000.0 |
|
| - - (Test for Sulphate content [IS 4032 or relevant specification], %) |
1000.0 |
|
| 3 (Test for Carbonation [IS 516 (Part 5 / section 3)]) |
5000.0 |
|
| 8 (Test for compressive Strength (5) [IS 516 (Part 4)], in N/mm^2) |
25000.0 |
|
| - - (Test for Alkali content (5) [Is 4032 or relevant specification], %) |
5000.0 |
|
| - - (Test for Chloride Content (3) [ IS 4032 or relevant specification], %) |
3000.0 |
|
| - - (Test for Sulphate content (5) [IS 4032 or relevant specification]) |
5000.0 |
|
| - - (Hydrostatic Pressure Test, Depth of penetration on RCC Grade Concrete.) |
10000.0 |
|
| - - (Hydrostatic Pressure Test, Depth of penetration on PQC Grade Concrete.) |
10000.0 |
|
| - - (Preparation of RCC Grade Concrete) |
10000.0 |
|
| - - (Preparation of PQC Grade Concrete) |
10000.0 |
|
|
| 190 |
Customized Specification for Shore D hardness test - Customized Specification for Shore D hardness test [-] |
Customized Specification for Shore D hardness test |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Shore D harness) |
1000.0 |
|
|
| 191 |
1834 (1984) - SPECIFICATION FOR HOT APPLIED SEALING COMPOUNDS FOR
JOINTS IN CONCRETE |
SPECIFICATION FOR HOT APPLIED SEALING COMPOUNDS FOR
JOINTS IN CONCRETE |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Pour Point) |
1500.0 |
|
| - (Flow Test) |
1500.0 |
|
| - (Penetration) |
1500.0 |
|
|
| 192 |
Customized Specification for SHYLA TOTE LARGE AST - Customized Specification for SHYLA TOTE LARGE AST |
Customized Specification for SHYLA TOTE LARGE AST |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Nomenclature) |
500.0 |
|
| - (Outer dimensions(cm.) 37.4x14.7x26.3(+/-5%)) |
500.0 |
|
| - (Weight(Kg.) 0.60(+/-5%)) |
1000.0 |
|
| - (Capacity(ltrs)4.67(+/-5%)) |
1000.0 |
|
| - (Colour(assorted)) |
500.0 |
|
| - (Active Ingredient(Synthetic fabric)) |
2000.0 |
|
| - (Identification Mark/Marking) |
500.0 |
|
| - (Packing type and speciofication) |
500.0 |
|
|
| 193 |
Customized specification for SAIMAA LG HZ TOTE - Customized specification for SAIMAA LCHZ TOTE |
Customized specification for SAIMAA LCHZ TOTE |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Nomenclature of the product) |
500.0 |
|
| - (Specification(cm.)45x15x25(+/-5%)) |
500.0 |
|
| - (Weight(Kg.) 0.7(+/-6%)) |
1000.0 |
|
| - (Colour (assorted)) |
500.0 |
|
| - (Volume(ltrs) 10(+/-10%)) |
1000.0 |
|
| - (Packing type and specification) |
500.0 |
|
| - (Identification Mark/Marking) |
500.0 |
|
|
| 194 |
Customized Specification for LAVIE LADIES HANDBAG CROCO BURSA LG TOTE-NAVY - Customized Specification for LAVIE LADIES HANDBAG CROCO BURSA LG TOTE-NAVY |
Customized Specification for LAVIE LADIES HANDBAG CROCO BURSA LG TOTE-NAVY |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Nomenclature) |
500.0 |
|
| - (Specification(cm.) 42x13x28 (+/-3)) |
500.0 |
|
| - (Weight(Kg.) 0.70(+/-6%)) |
1000.0 |
|
| - (Colour) |
500.0 |
|
| - (Volume(ltrs) 5 (+/-6%)) |
1000.0 |
|
| - (Packing type and specification) |
500.0 |
|
| - (Identification Mark/Marking) |
500.0 |
|
|
| 195 |
Customized Specification for NUWARE MICROWAVE SAFE DINNER SET - Customized Specification for NUWARE MICROWAVE SAFE DINNER SET |
Customized Specification for NUWARE MICROWAVE SAFE DINNER SET |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Nomenclature) |
500.0 |
|
| - (Description) |
500.0 |
|
| - (Colour) |
500.0 |
|
| - (Packing Specification) |
500.0 |
|
| - (Identification Mark/Marking) |
500.0 |
|
| - (Active Ingredient) |
2000.0 |
|
|
| 196 |
RDSO M&C/ PCN/ 100/ 2018 (2018) - Specification for Epoxy Cum Polyurethane Painting System (Two Pack) for the Exterior Painting of Railway Coaches |
Specification for Epoxy Cum Polyurethane Painting System (Two Pack) for the Exterior Painting of Railway Coaches |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Chapter V (Table 1) (Abrasion resistance-1000 cycles) |
3000.0 |
|
| Chapter V (Table 1) (Humidity test.) |
11000.0 |
|
| Chapter V (Table 1) (Durability Tests : Accelerated weathering test) |
110000.0 |
|
| Chapter V (Table 1) (Accelerated Tests Resistance to solvents) |
1500.0 |
|
| Chapter V (Table 1) (Accelerated Tests Resistance to water) |
1500.0 |
|
| Chapter V (Table 1) (Accelerated Tests Resistance to oil) |
1500.0 |
|
| Chapter V (Table 1) (Accelerated Tests Resistance to 20% caustic potash (weight by volume)) |
1500.0 |
|
| Chapter V (Table 1) (Accelerated Tests (a) Resistance to 30% Sulphuric acid (weight by volume)) |
1500.0 |
|
| Chapter V (Table 1) (Gloss at 60 degree angle of incidence) |
1200.0 |
|
| Chapter V (Table 1) (Viscosity (Efflux time by Ford cup No. 4 ) at 27 degree C) |
1200.0 |
|
| Chapter V (Table 1) (Fineness of grind) |
1200.0 |
|
| Chapter V (Table 1) (Theoretical Spreading rate) |
1200.0 |
|
| Chapter V (Table 1) (Pot life(After induction time)ii) 40 ± 2 Deg C) |
2000.0 |
|
| Chapter V (Table 1) (Pot life (After induction time) at i) 27 ± 2 Deg C) |
1500.0 |
|
| Chapter V (Table 1) (Mass in Kg/10 litres) |
1200.0 |
|
| Chapter V (Table 1) (Keeping Properties for both the packs) |
5000.0 |
|
| Chapter V (Table 1) (Flash Point (b) Component B) |
1200.0 |
|
| Chapter V (Table 1) (Flash Point (a) Component A) |
1200.0 |
|
| Chapter V (Table 1) (Flexibility & Adhesion (6.25mm mandrel)) |
1200.0 |
|
| Chapter V (Table 1) (Scratch hardness (1.5 Kg LOAD)) |
1200.0 |
|
| Chapter V (Table 1) (Volume solids) |
1200.0 |
|
| Chapter V (Table 1) (Dry film thickness/Per coat) |
1200.0 |
|
| Chapter V (Table 1) (Colour) |
1200.0 |
|
| Chapter V (Table 1) (Finish) |
1200.0 |
|
| Chapter V (Table 1) (Consistency) |
1200.0 |
|
| Chapter IV / Table I (Drying time c) Hard Dry at 70 Deg C) |
1200.0 |
|
| Chapter V (Table 1) (Drying time b) Hard Dry) |
1200.0 |
|
| Chapter V (Table 1) (Drying time a) Surface Dry) |
1200.0 |
|
| Chapter V (Table 1) (poly isocyanate, in hardener) |
3000.0 |
|
|
| 197 |
BSEN 13348 (2016) - Copper and Copper Alloy - Seamless Round Copper Tube for Medical Gases or vacuum |
Copper and Copper Alloy - Seamless Round Copper Tube for Medical Gases or vacuum |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.3 (Dimension - Outer Diameter mm, in accordanc e with BS EN 13348 (2016) Table 2, 3 and 4) |
1000.0 |
|
| 6.3 (Dimension - Thickness of the Tube in mm in accordance with BS EN 13348(2016) Table 2, 3 and 4) |
1000.0 |
|
| 6.2 (Tensile Strength) |
2000.0 |
|
| 6.2 (Elongation) |
1000.0 |
|
| 6.2 (Hardness) |
2000.0 |
|
| 8.5 (Bending Test) |
1000.0 |
|
| 8.6 (Drift Expansion test) |
2000.0 |
|
| 6.1 (Cu + Ag) |
4000.0 |
|
| 6.1 (Phosphorus (% by mass)) |
1000.0 |
|
| 6.1 (Chemical Composition (% by mass)) |
2000.0 |
|
|
| 198 |
IS 8887 (2004) - Bitumen Emulsion for Roads (Cationic Type) |
Bitumen Emulsion for Roads (Cationic Type) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.2 and 6.2 (Viscosity by say bolt viscometer) |
1000.0 |
|
| 4.2 and 6.2 (Solubility in Trichloroethylene) |
1000.0 |
|
| 4.2 an 6.2 (Residue by Evaporation) |
1500.0 |
|
|
| 199 |
IS 14223 (Part 1):2023 - Polished Building Stones —Specification (Part 1-Granite and Similar Stones) |
Polished Building Stones —Specification (Part 1-Granite and Similar Stones) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5,Table 1-(i) (Specific gravity ( as per IS 1124)) |
1000.0 |
|
| 5,Table-1(ii) (Water absorption (as per IS 1124)) |
1000.0 |
|
| 5,Table-1(iii) (Compressive strength, in N/mm2 (as per IS 1121 (Part 1))) |
3000.0 |
|
| 5,Table-1(vi) (Hardness, in Mohs (as per IS 13630 (Part 13))) |
2000.0 |
|
| 5,Table-1(x) (Resistance to wear- a)Average b)Individual maximum, in mm (as per IS 1706)) |
4000.0 |
|
| custom (Moisture content (%)) |
500.0 |
|
| custom (Dry density) |
1000.0 |
|
| custom (Flexural strength) |
3000.0 |
|
| custom (Porosity) |
1000.0 |
|
|
| 200 |
Custom specification- Bipolar for metro rail (general chemical) - Custom specification- Bipolar for metro rail (general chemical) |
Custom specification- Bipolar for metro rail (general chemical) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Appearance) |
500.0 |
|
| - (Odour) |
500.0 |
|
| - (Skin Irritation) |
500.0 |
|
| - (pH Value) |
1000.0 |
|
| - (Viscosity by Flow cup) |
1000.0 |
|
| - (Accelerated Corrosion test ( For 21 Hours) with raw water) |
1500.0 |
|
| - (Accelerated Corrosion (for 21 hours) with Bipolar) |
1500.0 |
|
| - (Specific Gravity) |
1000.0 |
|
|
| 201 |
IS 8986 (2022) (2022) - Hexagonal Integral Drill Steel and Extension Rods and Hollow Round Drill Steel in Bar Form — Dimensions
(Second Revision) |
Hexagonal Integral Drill Steel and Extension Rods and Hollow Round Drill Steel in Bar Form — Dimensions
(Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 2 (Dimension - Hexagonal Integral Drill Steel and Extension Rods in mm Clause 2.1 and Table 1 of IS 8986 or any other relevant National & International Standard Specified) |
1000.0 |
|
| 2 (Dimension -Hollow Round Drill Steel in Bar Form for Extension Rods, in mm, Clause 2.2, Table 2 of IS 8986 or any other national or International Stanard specified) |
1000.0 |
|
| 2 (Mass per Meter in Kg/M as per Table 1 or 2 of IS 8986 or any other National or International Standard specified.) |
1000.0 |
|
| 0 (Rockwell Hardness Test in HRC) |
2000.0 |
|
| 0 (Mechanical Properties - Tensile Strength, Yield Strength and % of Elongation as per IS 1608 Prt-1 or ASTM E8 or any other relevant National or International specification.) |
4000.0 |
|
| 2 (Sectional Area in mm2 as per IS 8986 Clause 2 Table 1 /Table 2) |
1000.0 |
|
| 0 (Chemical Composition in mass% by OES method or any other National or International product specification specified test method.) |
3500.0 |
|
|
| 202 |
IS 17044 (2018) - Intumescent fire retardant paint (Water Based) - Specification |
Intumescent fire retardant paint (Water Based) - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Intumescent fire retardant paint (Water Based) - Specification (Please refer to the annexure for the test result) |
10000.0 |
|
|
| 203 |
IS 5758 (2020) - Precast Concrete Kerbs, Channels, Edgings, Quadrants and Gutter Aprons |
Precast Concrete Kerbs, Channels, Edgings, Quadrants and Gutter Aprons |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 9.2 (Dimensions, Overall Length, in mm) |
500.0 |
|
| 9.2 (Dimensions, Overall Height, in mm) |
500.0 |
|
| 9.2 (Overall Thickness, in mm) |
500.0 |
|
| 9.3 (Bending Strength, N/mm^2) |
4000.0 |
|
| 9.4 (Water Absorption, in %) |
2000.0 |
|
| 4.2 (Shape and Profile) |
1000.0 |
|
|
| 204 |
IS 15961 (2012) - Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain) |
Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 9 (Triple Spot Coating Mass) |
2000.0 |
|
|
| 205 |
IS 15965 : 2012 (2012) - Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain) |
Pre-painted Aluminium Zinc Alloy Metallic Coated Steel Strip and Sheet (Plain) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.3 (Total Coated Thickness (As received condition), mm) |
1000.0 |
|
| 8 (Tensile Strength (As per IS 15961), MPa) |
1000.0 |
|
| 8 (Yield Strength (As per IS 15961), MPa) |
1000.0 |
|
| 8 (% Elongation (As per IS 15961), %) |
1000.0 |
|
| 7.1 (Mass of Coating (Both sides), g/m²) |
2000.0 |
|
| 5 (Chemical composition (As per IS 513), % by mass) |
2500.0 |
|
| 1 (Composition of AZ Coating Material in %) |
3000.0 |
|
|
| 206 |
Customized Specification for Plastic Bottle with cap - Customized Specification for Plastic Bottle with cap |
Customized Specification for Plastic Bottle with cap |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Identification of Plastic bottle body by FTIR) |
2000.0 |
|
| - (Identification of plastic cap by FTIR) |
2000.0 |
|
|
| 207 |
- (2025) - Customize General chemical specifical NTH (WR) |
Customize General chemical specifical NTH (WR) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Appearance) |
500.0 |
|
| - (Specific gravity) |
1000.0 |
|
| - (Releasing Properties) |
3000.0 |
|
| - (Flash Point by COC) |
1000.0 |
|
| - (Fire Point by COC) |
1000.0 |
|
| - (Aluminium Reactivity at 60 deg. C for 72 hours) |
1000.0 |
|
| - (Effect on Wooden Ply at 60 deg C. for 72 hours) |
1000.0 |
|
| - (Viscosity by Flow Cup) |
1000.0 |
|
|
| 208 |
16720 (2018) - Pulverized Fuel Ash - Cement Bricks |
Pulverized Fuel Ash - Cement Bricks |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 8.1 (General) |
500.0 |
|
| 8.2 (Dimension, Length, in mm) |
500.0 |
|
| 8.2 (Dimensions, Width) |
500.0 |
|
| 8.2 (Dimensions, Thickness, in mm) |
500.0 |
|
| 8.3 (Density, in kg/m^3) |
1000.0 |
|
| 8.4 (Compressive Strength, in N/mm^2) |
2000.0 |
|
| 8.5 (Drying Shrinkage, in %) |
2000.0 |
|
| 8.6 (Water Absorption Test) |
1000.0 |
|
|
| 209 |
IS 18387 (2023) - Gypsum Ceiling Tiles |
Gypsum Ceiling Tiles |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7.1.1 (Dimensions and Tolerances on size, Length in mm) |
500.0 |
|
| 7.1.1 (Dimensions and Tolerances on Size, Width) |
500.0 |
|
| 7.1.2 (Dimensions and Tolerances on Edges Profile) |
500.0 |
|
| 7.2.2 (Tolerances on Squareness of Edges,) |
500.0 |
|
| 7.3 (Density, in kg/m^3) |
1000.0 |
|
| 7.4 (Flexural Breaking Strength (Length wise), in N) |
2000.0 |
|
| 7.4 (Flexural Breaking Strength (Across the length), in N) |
2000.0 |
|
| 7.5 (Water Absorption, in %) |
1000.0 |
|
| 7.8 (Humidified Deflection, in mm) |
5000.0 |
|
|
| 210 |
Customized Specification for Plastic Material - Customized Specification for Plastic Material |
Customized Specification for Plastic Material |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Material Identification by FTIR) |
2000.0 |
|
| - (Hardness) |
1000.0 |
|
|
