| 121 |
RDSO SPECIFICATION No. M&C/ PCN/ 100/ 2018 (2018) - FULL GLOSS POLYURETHANE ENAMEL (TWO PACK) |
FULL GLOSS POLYURETHANE ENAMEL (TWO PACK) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Identification of polyisocyanates) |
1200.0 |
|
| 2 (Drying time
a) Surface dry
b) Hard dry
c) Hard dry at 70 Deg. C) |
3600.0 |
|
| 3 (Consistency) |
1200.0 |
|
| 4 (Finish) |
1200.0 |
|
| 5 (Colour) |
1200.0 |
|
| 6 (Dry film thickness) |
1200.0 |
|
| 7 (Volume solids) |
1200.0 |
|
| 8 (Scratch hardness (1.5 Kg Load)) |
1200.0 |
|
| 9 (Flexibility & Adhesion (6.25 mm mandrel)) |
1200.0 |
|
| 10 (Flash point
(a) Component ‘A’
(b) Component ‘B’) |
2400.0 |
|
| 11 (Fineness of Grind) |
1200.0 |
|
| 12 (Pot life (After induction time) at
a) 27±2°C
b)40±2ºC) |
1500.0 |
|
| 13 (Gloss at 60° angle of incidence) |
1200.0 |
|
| 14 (Mass in Kg/10 litres) |
1200.0 |
|
| 15 (Keeping properties) |
5000.0 |
|
| 16 (Theoretical spreading rate) |
2000.0 |
|
| 17 (% poly isocyanate by mass, in hardener) |
3000.0 |
|
| 18 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix. Of two components at 27± 2 °C in Supply condition) |
1200.0 |
|
| 19 (Accelerated Tests
(a) Resistance to 30% Sulphuric acid (weight by volume)
(b) Resistance to 20% caustic potash (weight by volume)
(c) Resistance to oil
(d) Resistance to solvents
(e) Resistance to water) |
7200.0 |
|
| 20 (Durability Tests Accelerated weathering test) |
37500.0 |
|
| RDSO SPECIFICATION No. M&C/ PCN/ 100/ 2018 (Please refer annexure for test result (Table 1. Full Gloss Polyurethane Enamel Two Pack) Except parameter Unreacted monomer) |
21000.0 |
|
| 22 (Abrasion resistance-1000 Cycle) |
5000.0 |
|
|
| 122 |
RDSO Specification No. M&C/PCN/100/2018 - POLYURETHANE SURFACER (TWOPACK) |
POLYURETHANE SURFACER (TWOPACK) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Drying time
a) Surface dry
b) Hard dry
c) Hard dry at 70°C) |
3600.0 |
|
| 2 (Consistency) |
1200.0 |
|
| 3 (Finish) |
1200.0 |
|
| 4 (Colour) |
1200.0 |
|
| 5 (Dry film thickness) |
1200.0 |
|
| 6 (Volume solids, %) |
2000.0 |
|
| 7 (Scratch hardness (1.5Kg Load)) |
1200.0 |
|
| 8 (Flexibility & Adhesion (6.25 mm mandrel)) |
1200.0 |
|
| 9 (Flashpoint
a) Component ‘A’
b) Component ‘B’) |
2400.0 |
|
| 10 (Fineness of Grind) |
1200.0 |
|
| 11 (Pot life (After induction time)
i) 27±2°C
ii) 40±2°C) |
1500.0 |
|
| 12 (Mass in Kg/10 litres) |
1200.0 |
|
| 13 (Keeping properties) |
2000.0 |
|
| 14 (Theoretical spreading rate) |
2000.0 |
|
| 15 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix of two components at 27± 2 °C in Supply condition) |
1200.0 |
|
|
| 123 |
NTH/ER/RPPT/HDPE PIPE INSPECTION-2025 - INSPECTION OF HDPE PIPES |
INSPECTION OF HDPE PIPES |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Firm's request (Inspection Report) |
19800.0 |
|
|
| 124 |
RDSO SPECIFICATION M&C/PCN/100/2018 PUTTY - UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK) |
UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Drying time:
a)Surface dry
b) Hard dry
c)Hard dry time at 70 Deg. C) |
3600.0 |
|
| 2 (Consistency) |
1200.0 |
|
| 3 (Stopping properties) |
2000.0 |
|
| 4 (Rubbing properties) |
2000.0 |
|
| 5 (Hold out Property) |
2000.0 |
|
| 6 (Adhesion & Compatibility of Paint System) |
2000.0 |
|
| 7 (Pot life ,at 27±2 Deg. C) |
1500.0 |
|
| 8 (% solids) |
1200.0 |
|
| 9 (Keeping properties) |
5000.0 |
|
|
| 125 |
Custom Paint finishing Aluminium paint Heat resistance - Custom Paint finishing Aluminium paint Heat resistance |
Custom Paint finishing Aluminium paint Heat resistance |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Preliminary Examination) |
1000.0 |
|
| 2 (Consistency) |
1000.0 |
|
| 3 (Flash Point (Abel)) |
1000.0 |
|
| 4 (Efflux time at 27(+/-)5 Deg.C ( for first 50 ml)) |
1000.0 |
|
| 5 (Application Properties & Finish) |
1000.0 |
|
| 6 (Covering Power) |
1000.0 |
|
| 7 (Drying time (i) Surface dry) |
1000.0 |
|
| 8 (Drying time (ii) Hard dry) |
1000.0 |
|
| 9 (Colour) |
1000.0 |
|
| 10 (Flexibility & Adhesion (Bend Test)) |
1000.0 |
|
| 11 (Scratch Hardness) |
1000.0 |
|
| 12 (Volatile matter) |
1000.0 |
|
| 13 (Resistance to high Temperature (a) At 300 Deg.C For 4 Hours) |
1000.0 |
|
| 14 (Resistance to high Temperature (b) At 400 Deg.C For 1 Hour) |
1000.0 |
|
| 15 (Resistance to high Temperature (c) At 600 Deg.C For 1 Hour) |
1000.0 |
|
|
| 126 |
Custom Paint RFU Finishing various shades - Custom Paint RFU Finishing various shades |
Custom Paint RFU Finishing various shades |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 20 (Durability Test (25 days Outdoor Exposure Then 96 hours salt Spray)) |
5000.0 |
|
| 19 (Accelerated Storage stability) |
3000.0 |
|
| 15 (Resistance to Salt Spary (96 hrs)) |
4800.0 |
|
| 18 (Presence of Rosin Derivative) |
1000.0 |
|
| 17 (Non-volatile Content) |
1000.0 |
|
| 16 (Flash Point (Abel)) |
1000.0 |
|
| 14 (Stripping Test) |
1000.0 |
|
| 13 (Scratch Hardness) |
1000.0 |
|
| 12 (Flexibility & Adhesion (Bend Test)) |
1000.0 |
|
| 11 (Wet Opacity) |
1500.0 |
|
| 10 (Colour) |
1000.0 |
|
| 9 (Gloss) |
1000.0 |
|
| 8 (Fineness of Grind) |
1000.0 |
|
| 7 (Finish) |
1000.0 |
|
| 6 (Drying time (iii) Tack free dry) |
1000.0 |
|
| 5 (Drying time (ii) Hard dry) |
1000.0 |
|
| 4 (Drying time (i) Surface dry) |
1000.0 |
|
| 3 (Relative consistency at 27 deg. C) |
1000.0 |
|
| 2 (Consistency) |
1000.0 |
|
| 1 (Preliminary Examination) |
1000.0 |
|
| 33 (Natural outdoor weathering) |
3000.0 |
|
| 32 (Resistance to warm water (45 ± 3 °C for 4 hours)) |
1200.0 |
|
| 31 (Resistance to heat (after air drying for 48 hours) Except White) |
1200.0 |
|
| 30 (Resistance to petrol -benzol mixture) |
1200.0 |
|
| 29 (Resistance to Alkali) |
1500.0 |
|
| 28 (Resistance to Acid) |
1500.0 |
|
| 27 (Mass in Kg/10 litres) |
1200.0 |
|
| 26 (Accelerated Storage Stability test) |
3000.0 |
|
| 25 (Lead Restriction total lead compound as PbO expressed as % of dry pigment) |
1000.0 |
|
| 24 (Water content, %) |
1200.0 |
|
| 23 (Resistance to Humidity under condition of condensation) |
12000.0 |
|
| 22 (Application) |
1200.0 |
|
| 21 (Efflux time (Ford Cup No. 4) at 30 ±1 Deg. C) |
1200.0 |
|
| 33 (Natural outdoor weathering) |
3000.0 |
|
|
| 127 |
MMDTS 18034 (Rev. 04) (2019) - Technical Specification for PU based Wet -On- Wet Applicable on Exterior Painting System for LHB Types Coaches. |
Technical Specification for PU based Wet -On- Wet Applicable on Exterior Painting System for LHB Types Coaches. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 ((Anti Graffiti test ASTM D-6578)) |
5000.0 |
|
|
| 128 |
CUSTOM PAINT ONSITE TESTING-1 (2024) - CUSTOM PAINT ONSITE TESTING-1 |
CUSTOM PAINT ONSITE TESTING-1 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Distinctness of Image (DOI)) |
10000.0 |
|
|
| 129 |
IRC 105 (2019) - SPECIFICATIONS FOR DENSE BITUMINOUS MACADAM AND BITUMINOUS CONCRETE FOR AIRFIELD PAVEMENTS |
SPECIFICATIONS FOR DENSE BITUMINOUS MACADAM AND BITUMINOUS CONCRETE FOR AIRFIELD PAVEMENTS |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Table 3.5 (Durability [ Soundness (Sodium sulphate )], %) |
2000.0 |
|
| Table 3.5 (Durability [Soundness (Magnesium or Sodium Sulphate )], %) |
2000.0 |
|
| Table 3.5 (Particle Shape (Combined Flakiness and Elongation Index), %) |
3000.0 |
|
| Table 3.5 (Strength [Los Angeles Abrasion Value], %) |
1500.0 |
|
| Table 3.5 (Strength [Aggregate Impact Value], %) |
1500.0 |
|
| 2 (Density of DAC (On lines of ASTM D 2726)) |
2000.0 |
|
| 2 (Density of DBM (On lines of ASTM D 2726)) |
2000.0 |
|
|
| 130 |
ASTM B117 Salt spray - ASTM B 117 Salt spray Test For 96 hrs |
ASTM B 117 Salt spray Test For 96 hrs |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 131 |
Custom/Mech/2022 (2022) - Specification for Customer Test request. |
Specification for Customer Test request. |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 0 (Chemical Composition) |
4000.0 |
|
| 0 (Mass of Zinc Coating) |
4000.0 |
|
| 0 (Test results Chemical as per annexure) |
10000.0 |
|
| 0 (Test results as per annexure) |
61200.0 |
|
| 8 (Dimensions) |
2500.0 |
|
| 0 (0.2% proof stress, MPa) |
1000.0 |
|
| 0 (Percent Elongation) |
5000.0 |
|
| 0 (Bend test) |
1000.0 |
|
| 0 (Proof Load) |
3000.0 |
|
| 0 (Load test of Wedge on the lines of IS 14268) |
3000.0 |
|
| 0 (Salt Spray test, 1440 Hrs.) |
60000.0 |
|
| 0 (Tensile strength test, N/mm2) |
5000.0 |
|
| 0 (Decarburization test) |
3000.0 |
|
| 0 (Load Test) |
5000.0 |
|
| 0 (Dimensions of Bolt Nut and washer) |
2000.0 |
|
| 0 (Chemical Analysis(SS 304/SS 316) of Bolt, Nut and washers) |
8000.0 |
|
| M1 (Shear Strength test, MPa) |
3000.0 |
|
| C2 (Brinell/ Vickers/ Rockwell Hardness) |
2000.0 |
|
| C3 (Tensile Strength (MPa)) |
1000.0 |
|
| 0 (Impact test, J) |
3000.0 |
|
| 0 (Microstructure analysis) |
3000.0 |
|
| 0 (Percent Reduction of Area) |
1000.0 |
|
| 0 (Breaking Load) |
3000.0 |
|
| 0 (Test results) |
10000.0 |
|
| 0 (Compression Test) |
3000.0 |
|
| 0 (Uniformity of Coating) |
2000.0 |
|
| 0 (Coating Thickness) |
2000.0 |
|
| 0 (Adhesion Test) |
1000.0 |
|
| 0 (Flattening Test) |
1000.0 |
|
|
| 132 |
CUSTOM/Aluminium Polymer Composites (APC) /2024 - CUSTOM/Aluminum Polymer Composites (APC) /2024 |
CUSTOM/Aluminum Polymer Composites (APC) /2024 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Density) |
1000.0 |
|
| 2.0 (Water Absorption) |
1000.0 |
|
| 3.0 (Tensile Strength) |
2000.0 |
|
| 4.0 (Tensile Elongation) |
1000.0 |
|
| 5.0 (Flexural Strength) |
2000.0 |
|
| 6.0 (Flexural Modulus) |
2000.0 |
|
| 7.0 (Resistance to wet Heat) |
2000.0 |
|
| 8.0 (Stain Resistance) |
5000.0 |
|
| 9.0 (Wear and Clanability) |
2000.0 |
|
| 10.0 (Light Resistance (Xenon Arc).) |
3000.0 |
|
|
| 133 |
MDTS - 46303 (2016) - Schedule of Technical Requirements For Composite Decorative Glass Fabric Reinforced Plastic (DGFRP) |
Schedule of Technical Requirements For Composite Decorative Glass Fabric Reinforced Plastic (DGFRP) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.2 (Density) |
1000.0 |
|
| 3.2 (Tensile Strength Along the Length) |
1000.0 |
|
| 3.2 (Tensile Strength Along the Width) |
1000.0 |
|
| 3.2 (Breaking Strength along the length) |
1000.0 |
|
| 3.2 (Breaking Strength along the Width) |
1000.0 |
|
| 3.2 (Water Absorption) |
1000.0 |
|
| 3.2 (Drop Impact Test) |
1000.0 |
|
| 3.2 (Resistance to staining rating scale) |
5000.0 |
|
| 3.2 (Resistance to Color Change in Xenon Arch Light) |
3000.0 |
|
| 3.2 (Resistance to Surface Wear) |
5000.0 |
|
| 3.2 (Resistance to Immersion in Boiling Water -Appearance) |
500.0 |
|
| 3.2 (Resistance to Immersion in Boiling Water- Increase in Thickness) |
1000.0 |
|
| 3.2 (Resistance to immersion in boiling Water- De-lamination) |
500.0 |
|
| 3.2 (Resistance To Surface Wear) |
5000.0 |
|
|
| 134 |
CUSTOM/JUTE SAND SNAKE/2024 - CUSTOM/JUTE SAND SNAKE/2024 |
CUSTOM/JUTE SAND SNAKE/2024 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Mass) |
1000.0 |
|
| 2.0 (Thread Used) |
1000.0 |
|
| 3.0 (Construction) |
1000.0 |
|
| 4.0 (Length) |
500.0 |
|
| 5.0 (Width) |
500.0 |
|
|
| 135 |
Custom - Diesel |
Diesel |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Density) |
1200.0 |
|
| 2 (Flash point) |
1200.0 |
|
|
| 136 |
IS 17048 (2018) - Halogen Free Flame Retardant (HFFR) Cables for Working Voltages up to and including 1100 Volts-Specification |
Halogen Free Flame Retardant (HFFR) Cables for Working Voltages up to and including 1100 Volts-Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 15.6 Table 2 (iii) (a) (i) (Conductor Resistance Test) |
1500.0 |
|
| 15.6 Table 2 (iii) (a) (ii) (Annealing Test (For copper)) |
1000.0 |
|
| 15.6 Table 2 (iii) (b) (Test for Overall Dimensions and Thickness of Insulation and Sheath) |
1000.0 |
|
| 15.6 Table 2 (iii) (c) (iii) (Insulation Resistance Test) |
2000.0 |
|
| 15.6 Table 2 (iii) (c) (ii) or (iii) (f) (i) (High Voltage Test) |
1500.0 |
|
| 15.6 Table 2 (ii) (f) (Tensile strength and elongation at break) |
1500.0 |
|
| 15.6 Table 2 (iii) (c) (xiii) & (iii) (f) (v) (Flame Retardant Test) |
3000.0 |
|
| 15.6 Table 2 (iii) (f) (ii) (Flammability test) |
500.0 |
|
| - (Test on 2nd Core) |
2000.0 |
|
| - (Test on 3rd Core) |
2000.0 |
|
| - (Test on 4th Core) |
2000.0 |
|
|
| 137 |
IS 9537 : Part 2 (1981) - Specification for conduits for electrical installations: Part 2 rigid steel conduits |
Specification for conduits for electrical installations: Part 2 rigid steel conduits |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 9.2 (Bending Test (With Seam on the Outside of flank)) |
500.0 |
|
| 9.2 (Bending Test (With Seam on the flank)) |
500.0 |
|
| 13 (External Influence Test (With Seam on the flank)) |
1000.0 |
|
| 13 (External Influence Test (With Seam on the Outside of the Bend)) |
1000.0 |
|
| 9.3 (Compression Test) |
3000.0 |
|
| 7 (Wall thickness) |
500.0 |
|
| 7 (Outside Diameter) |
500.0 |
|
| 7.2 (Checking the Minimum outside diameter.) |
750.0 |
|
| 7.2 (Checking the Maximum outside diameter) |
750.0 |
|
|
| 138 |
CUSTOM/SHARPENER/2024 - Material |
Material |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Material) |
1000.0 |
|
|
| 139 |
CUSTOM/CRAYONS/2024 - CUSTOM/CRAYONS/2024 |
CUSTOM/CRAYONS/2024 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (No. of Shades) |
500.0 |
|
| 2.0 (Material) |
500.0 |
|
| 3.0 (Colour) |
500.0 |
|
| 4.0 (Crayons Shape) |
500.0 |
|
| 5.0 (Crayon length) |
1000.0 |
|
| 6.0 (Crayon Diameter) |
1000.0 |
|
|
| 140 |
CUSTOM/ERASER/2024 - CUSTOM/ERASER/2024 |
CUSTOM/ERASER/2024 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Material) |
1000.0 |
|
| 2.0 (Dimension) |
1000.0 |
|
|
| 141 |
CUSTOM/PENCIL/2024 - CUSTOM/PENCIL/2024 |
CUSTOM/PENCIL/2024 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Material) |
1000.0 |
|
| 2.0 (Length) |
1000.0 |
|
|
| 142 |
CUSTOM/PENCIL BOX/2024 - CUSTOM/PENCIL BOX/2024 |
CUSTOM/PENCIL BOX/2024 |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1.0 (Material) |
1000.0 |
|
| 2.0 (Type) |
1000.0 |
|
| 3.0 (Dimension) |
1000.0 |
|
| 4.0 (Pattern) |
500.0 |
|
| 5.0 (Weight) |
1000.0 |
|
|
| 143 |
ASTM D 1653 - Water Vapor Transmission |
Water Vapor Transmission |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Water Vapor Transmission) |
5000.0 |
|
|
| 144 |
Custom Specification for Electrical Testing Laboratory ,NTH(ER),Salt Lake - Custom Specification for Electrical Testing Laboratory ,NTH(ER),Salt Lake |
Custom Specification for Electrical Testing Laboratory ,NTH(ER),Salt Lake |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| A10 (Custom Specification 10) |
100000.0 |
|
| A1 (Custom Specification 1) |
10000.0 |
|
| A2 (Custom Specification 2) |
20000.0 |
|
| A7 (Custom Specification 7) |
70000.0 |
|
| A5 (Custom Specification-A5) |
50000.0 |
|
|
| 145 |
ND Custom 10 (2024) - Load Bearing Capacity for RCPC Slabs |
Load Bearing Capacity for RCPC Slabs |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Firm's Requirement (Load Bearing Capacity Test) |
3000.0 |
|
|
| 146 |
IS IS 1708 : Part 18 (1986) - Timber |
Timber |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 147 |
IS IS 1708 : Part 17 (1986) - Timber |
Timber |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 148 |
IS IS 1708 : Part 16 (1986) - Timber |
Timber |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 149 |
IS IS 1708 : Part 15 (1986) - Timber |
Timber |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 0 (Nail and screw holding power) |
3000.0 |
|
|
| 150 |
IS IS 1708 : Part 13 (1986) - Timber |
Timber |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 0 (Tensile Strength perpendicular to Grain) |
2000.0 |
|
|
