NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb@nic.in

Scope List

Reset

1161 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

EIL system no. 4_Coating system - F16+F16 = DFT 250 microns - EIL B269_000_02_042_PCS_0001 Rev_2 for EIL system no. 4

EIL B269_000_02_042_PCS_0001 Rev_2 for EIL system no. 4

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (100% Humidity test - (ASTM D2247))	20000.0
2 (Dry Heat Resistance Test (ASTM D2485 method B @ 550 deg C ))	5000.0
3 (Thermal Shock Resistance Test: 5 Cycles@30 minutes @120 Deg C and 15 minutes in water after quenching in water for each cycles, ASTM D 2485 method A)	10000.0

IS 7809 : Part 3 : Sec 1, IS 7809 : Part 2 & IS 7809 : Part 1 (1986) - Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 3 requirements or individual materials: Sec 1 plasticized polyvinylchloride tapes with non - Thermosetting adhesive (First Revision) & Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 1 General requirements & Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 2 Test Methods.

Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 3 requirements or individual materials: Sec 1 plasticized polyvinylchloride tapes with non - Thermosetting adhesive (First Revision) & Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 1 General requirements & Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 2 Test Methods.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2 (Width)	500.0
3.3 (Length)	500.0
3.4 (Thickness)	1000.0
4.1 (Tensile Strength)	1500.0
4.2 (Adhesion to Steel)	2000.0
4.3 (Adhesion to Backing)	2000.0
4.6 (Flammability)	5000.0

IEC 60068-2-52 - Environmental testing – Part 2-52: Tests – Test : Salt mist, cyclic (sodium chloride solution)

Environmental testing – Part 2-52: Tests – Test : Salt mist, cyclic (sodium chloride solution)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Environmental testing Test : Salt mist, cyclic (sodium chloride solution))	10000.0

EIL B269_000_02_042_PCS_0001 Rev_2 - F20_Interline 1064 Technical Name: Two components Glass flake filled Vinyl ester lining for under immersion service up to 90 Deg C

F20_Interline 1064 Technical Name: Two components Glass flake filled Vinyl ester lining for under immersion service up to 90 Deg C

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1) Volume solids % (Min) 2)DFT per coat (in Microns) 3)Theoretical Covering Capacity (in Msq /coat/l) 4)Weight /Liter (In kg /L for mixed paint) 5)Touch Dry at 30 deg.C (Max) hr 6)Hard Dry at 30 deg.C (Max) hr 7)Full Cure at 30 deg.C (For Immersion/High temp service) 8)Over coating Interval 9)Potlife 30 deg.C hr (for 2-component Paints) 10)Adhesion (MPA) 11)Temp Resistance (Min Deg.C) 12) weight per litre (Base & Hardener) 13) Ash Content (Base & Hardener) 14) Volatile & Non volatile matter (Base & Hardener))	28000.0

IS 7785 : Part 6 : Sec 1 (1981) - Elevated type aerodrome lighting fittings: Part 6 Taxiway lights, Section 1 Low intensity omni-directional elevated taxiway lighting fittings

Elevated type aerodrome lighting fittings: Part 6 Taxiway lights, Section 1 Low intensity omni-directional elevated taxiway lighting fittings

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0.4 (Mechanical Strength of Lead)	2000.0
0.4 (Mechanical Strength of Breakable Coupling)	3000.0
6.8 (Frangibility Test)	3000.0
6.9 (Wind Pressure Test)	3000.0

IS 7785 : Part 5 : Sec 1 (1981) - Elevated type aerodrome lighting fittings: Part 5 Approach lighting fittings, Section 1 High intensity elevated approach lighting fittings

Elevated type aerodrome lighting fittings: Part 5 Approach lighting fittings, Section 1 High intensity elevated approach lighting fittings

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.10 (Frangibility Test)	3000.0
6.11 (Wind Pressure Test)	3000.0
0.4 (Mechanical Strength of lead)	2000.0
0.4 (Mechanical Strength of Breakable Coupling)	3000.0

IS 7785 : Part 2 (1976 (RA 2018)) - Elevated type aerodrome lighting fittings: Part 2 Fixed focus high intensity bi-directional runway edge lighting fittings

Elevated type aerodrome lighting fittings: Part 2 Fixed focus high intensity bi-directional runway edge lighting fittings

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.9 (Mechanical Strength of lead)	2000.0
6.9 (Mechanical Strength of Breakable Coupling)	3000.0

EIL B269_000_02_042_PCS_0001 Rev_3 - EIL system no. 11_Coating system - F6A+F6A+F6A = DFT 300 microns

EIL system no. 11_Coating system - F6A+F6A+F6A = DFT 300 microns

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1)10 % & 40 % NaOH 2)5 % H2SO4 3)Xylene 4)Acetone 5)Ethanol 6)Kerosene 7)Sea water 8)100 % Humidity)	40000.0

EIL B269_000_02_042_PCS_0001 Rev_3 - EIL system no. 8_Coating system - F20+F20 = DFT 1100 microns

EIL system no. 8_Coating system - F20+F20 = DFT 1100 microns

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1)10 % & 40 % NaOH 2)5 % H2SO4 3)Xylene 4)Acetone 5)Ethanol 6)Kerosene 7)Sea water 8)DI water at 90 Deg 9)100 % Humidity)	45000.0

100

EIL B269_000_02_042_PCS_0001 Rev_3 - EIL system no. 7_Coating system - F7+F7+F7 = DFT 375 microns

EIL system no. 7_Coating system - F7+F7+F7 = DFT 375 microns

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (100% Humidity 1440 Hrs)	25000.0

101

Custom Paint 2024 new - Custom Paint 2024 new

Custom Paint 2024 new

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (VOC)	3000.0
2 (1. Lead Content 2. Cadmium Content 3. Chromium Content 4. Arsenic Content 5. Antimony Content 6. Mercury Content)	7200.0

102

405 (Part 2) - Lead Sheets and Strips - Specification

Lead Sheets and Strips - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Lead)	2000.0
4.1 (Antimony)	1200.0
4.1 (Zinc)	1200.0
4.1 (Total of all impurities)	1200.0

103

ASTM C 240 - Standard test method for testing cellular glass insulation block

Standard test method for testing cellular glass insulation block

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.3 (Water absorption, %)	3000.0
0 (Thermal shock)	24000.0

104

IS 3502 (2009) - Steel chequered plates (Third Revision)

Steel chequered plates (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 (Tensile Strength)	1000.0
8 (Yield Stress)	1000.0
8 (Percentage Elongation)	1000.0
10 (Dimensions)	1000.0
0 (Mass of Zinc Coating)	2000.0
5 (Freedom From Defects)	1000.0
4 (Carbon)	500.0
4 (Manganese)	500.0
4 (Sulphur)	500.0
4 (Phosphorus)	500.0
4 (Silicon)	500.0
4 (Carbon Equivalent)	1500.0

105

NTH/ER/SL/Electrical/Inspection - Inspection

Inspection

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Inspection A1)	28500.0
A2 (Inspection-A2)	17000.0
A3 (Inspection-A3)	50000.0
A4 (Inspection-A4)	30000.0

106

IRC 105:2019 (DBM+BC)/(ASTM D 2041/AASHTO T 166/ASTM D2172/ASTM D 6307) - Specification for Dense Bituminous Macadam and Bituminous content for airfield Pavements

Specification for Dense Bituminous Macadam and Bituminous content for airfield Pavements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Bitumen content/Binder content of DBM core(ASTM D2172/ASTM 6307))	3000.0
2 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of BC core (Aashto T 166/ASTM D 2041))	3000.0
1 (Density/Bulk density/Bulk specific gravity/Theoretical maximum specific gravity of DBM core (Aashto T 166/ASTM D 2041))	3000.0
4 (Bitumen content/Binder content of BC core(ASTM D2172/ASTM 6307/(IRC-SP-20-2002))	3000.0

107

CLW No.4TMS.096.029 Rev.1 (2009) - Specification for Non Adhesive Polyimide Film Tape

Specification for Non Adhesive Polyimide Film Tape

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.0 (Thickness)	1000.0
2.0 (Mass per unit area)	1000.0
2.0 (Tensile Strength at 23 deg.C)	2000.0
2.0 (Elongation at rupture at 23 deg.C)	1000.0

108

IS 10192 (1982) - Specification for synthetic resin bonded glass fibre (SRBGF) for electrical purposes

Specification for synthetic resin bonded glass fibre (SRBGF) for electrical purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (Appearance)	500.0
4.2 (Flatness)	1000.0
4.3 (Length)	500.0
4.3 (Width)	500.0
4.3 (Thickness)	1000.0
4.4 (Water absorption)	1000.0
4.4 (Tensile strength)	2000.0
4.4 (Cross breaking strength)	2000.0
4.4 (Compressive strength)	2000.0
4.4 (Impact strength edgewise)	2000.0
4.4 (Splitting resistance)	2000.0

109

16361:2015 (RA 202O) (2015) - Thermoplastic Polymer based Coatings: (a) Undercoating (b)Finishing

Thermoplastic Polymer based Coatings: (a) Undercoating (b)Finishing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Colour)	1200.0
3 (Viscosity (Brook field))	1500.0
2 (Consistency)	1200.0
4 (Drying Time, Hard Dry)	1200.0
5 (Dry film thickness)	1200.0
6 (Finish)	1200.0
7 (Mass per 10 litre)	1200.0
8 (Volume Solid (non volatile vehicle))	2000.0
9 (Flash point)	1200.0
10 (Resistance to heat)	1500.0
11 (Resistance to humidity)	1.0
12 (Resistance to neutral salt spray)	75000.0
13 (Resistance to water)	1200.0
14 (Resistance to acid)	1500.0
15 (Resistance to alkali)	1500.0
16 (Resistance to low temperature)	1000.0
17 (Moisture vapour permeability test)	5000.0
18 (Flexibility and adhesion test – Bend test)	1200.0
19 (Flexibility and adhesion test – Scratch hardness [Top coat (finishing)])	1200.0
20 (Fire retardant test)	5000.0
21 (a) Tensile test: Tensile strength b) Elongation at Break)	3000.0
23 (Durability test (QUV) [Top coat (finishing)])	25000.0

110

CUSTOM/POLYUTHERANE SPRING POST/2024 - POLYUTHERANE SPRING POST

POLYUTHERANE SPRING POST

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Material Identification)	4000.0
2.0 (Filler Content)	2000.0
3.0 (Density)	1000.0
4.0 (Melting Point)	1000.0
5.0 (Compressive Strength Horizontally)	2000.0
6.0 (Tensile Strength)	2000.0
7.0 (Elongation at Break)	1000.0
8.0 (UV Resistant (24 Hrs.))	1200.0

111

RDSO SPECIFICATION No. M&C/ PCN/ 100/ 2018 (2018) - FULL GLOSS POLYURETHANE ENAMEL (TWO PACK)

FULL GLOSS POLYURETHANE ENAMEL (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Identification of polyisocyanates)	1200.0
2 (Drying time a) Surface dry b) Hard dry c) Hard dry at 70 Deg. C)	3600.0
3 (Consistency)	1200.0
4 (Finish)	1200.0
5 (Colour)	1200.0
6 (Dry film thickness)	1200.0
7 (Volume solids)	1200.0
8 (Scratch hardness (1.5 Kg Load))	1200.0
9 (Flexibility & Adhesion (6.25 mm mandrel))	1200.0
10 (Flash point (a) Component ‘A’ (b) Component ‘B’)	2400.0
11 (Fineness of Grind)	1200.0
12 (Pot life (After induction time) at a) 27±2°C b)40±2ºC)	1500.0
13 (Gloss at 60° angle of incidence)	1200.0
14 (Mass in Kg/10 litres)	1200.0
15 (Keeping properties)	5000.0
16 (Theoretical spreading rate)	2000.0
17 (% poly isocyanate by mass, in hardener)	3000.0
18 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix. Of two components at 27± 2 °C in Supply condition)	1200.0
19 (Accelerated Tests (a) Resistance to 30% Sulphuric acid (weight by volume) (b) Resistance to 20% caustic potash (weight by volume) (c) Resistance to oil (d) Resistance to solvents (e) Resistance to water)	7200.0
20 (Durability Tests Accelerated weathering test)	37500.0
RDSO SPECIFICATION No. M&C/ PCN/ 100/ 2018 (Please refer annexure for test result (Table 1. Full Gloss Polyurethane Enamel Two Pack) Except parameter Unreacted monomer)	21000.0
22 (Abrasion resistance-1000 Cycle)	5000.0

112

RDSO Specification No. M&C/PCN/100/2018 - POLYURETHANE SURFACER (TWOPACK)

POLYURETHANE SURFACER (TWOPACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying time a) Surface dry b) Hard dry c) Hard dry at 70°C)	3600.0
2 (Consistency)	1200.0
3 (Finish)	1200.0
4 (Colour)	1200.0
5 (Dry film thickness)	1200.0
6 (Volume solids, %)	2000.0
7 (Scratch hardness (1.5Kg Load))	1200.0
8 (Flexibility & Adhesion (6.25 mm mandrel))	1200.0
9 (Flashpoint a) Component ‘A’ b) Component ‘B’)	2400.0
10 (Fineness of Grind)	1200.0
11 (Pot life (After induction time) i) 27±2°C ii) 40±2°C)	1500.0
12 (Mass in Kg/10 litres)	1200.0
13 (Keeping properties)	2000.0
14 (Theoretical spreading rate)	2000.0
15 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix of two components at 27± 2 °C in Supply condition)	1200.0

113

NTH/ER/RPPT/HDPE PIPE INSPECTION-2025 - INSPECTION OF HDPE PIPES

INSPECTION OF HDPE PIPES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's request (Inspection Report)	19800.0

114

RDSO SPECIFICATION M&C/PCN/100/2018 PUTTY - UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK)

UNSATURATED POLYESTER BASE KNIFING PUTTY (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying time: a)Surface dry b) Hard dry c)Hard dry time at 70 Deg. C)	3600.0
2 (Consistency)	1200.0
3 (Stopping properties)	2000.0
4 (Rubbing properties)	2000.0
5 (Hold out Property)	2000.0
6 (Adhesion & Compatibility of Paint System)	2000.0
7 (Pot life ,at 27±2 Deg. C)	1500.0
8 (% solids)	1200.0
9 (Keeping properties)	5000.0

115

Custom Paint finishing Aluminium paint Heat resistance - Custom Paint finishing Aluminium paint Heat resistance

Custom Paint finishing Aluminium paint Heat resistance

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Preliminary Examination)	1000.0
2 (Consistency)	1000.0
3 (Flash Point (Abel))	1000.0
4 (Efflux time at 27(+/-)5 Deg.C ( for first 50 ml))	1000.0
5 (Application Properties & Finish)	1000.0
6 (Covering Power)	1000.0
7 (Drying time (i) Surface dry)	1000.0
8 (Drying time (ii) Hard dry)	1000.0
9 (Colour)	1000.0
10 (Flexibility & Adhesion (Bend Test))	1000.0
11 (Scratch Hardness)	1000.0
12 (Volatile matter)	1000.0
13 (Resistance to high Temperature (a) At 300 Deg.C For 4 Hours)	1000.0
14 (Resistance to high Temperature (b) At 400 Deg.C For 1 Hour)	1000.0
15 (Resistance to high Temperature (c) At 600 Deg.C For 1 Hour)	1000.0

116

Custom Paint RFU Finishing various shades - Custom Paint RFU Finishing various shades

Custom Paint RFU Finishing various shades

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
20 (Durability Test (25 days Outdoor Exposure Then 96 hours salt Spray))	5000.0
19 (Accelerated Storage stability)	3000.0
15 (Resistance to Salt Spary (96 hrs))	4800.0
18 (Presence of Rosin Derivative)	1000.0
17 (Non-volatile Content)	1000.0
16 (Flash Point (Abel))	1000.0
14 (Stripping Test)	1000.0
13 (Scratch Hardness)	1000.0
12 (Flexibility & Adhesion (Bend Test))	1000.0
11 (Wet Opacity)	1500.0
10 (Colour)	1000.0
9 (Gloss)	1000.0
8 (Fineness of Grind)	1000.0
7 (Finish)	1000.0
6 (Drying time (iii) Tack free dry)	1000.0
5 (Drying time (ii) Hard dry)	1000.0
4 (Drying time (i) Surface dry)	1000.0
3 (Relative consistency at 27 deg. C)	1000.0
2 (Consistency)	1000.0
1 (Preliminary Examination)	1000.0
33 (Natural outdoor weathering)	3000.0
32 (Resistance to warm water (45 ± 3 °C for 4 hours))	1200.0
31 (Resistance to heat (after air drying for 48 hours) Except White)	1200.0
30 (Resistance to petrol -benzol mixture)	1200.0
29 (Resistance to Alkali)	1500.0
28 (Resistance to Acid)	1500.0
27 (Mass in Kg/10 litres)	1200.0
26 (Accelerated Storage Stability test)	3000.0
25 (Lead Restriction total lead compound as PbO expressed as % of dry pigment)	1000.0
24 (Water content, %)	1200.0
23 (Resistance to Humidity under condition of condensation)	12000.0
22 (Application)	1200.0
21 (Efflux time (Ford Cup No. 4) at 30 ±1 Deg. C)	1200.0
33 (Natural outdoor weathering)	3000.0

117

MMDTS 18034 (Rev. 04) (2019) - Technical Specification for PU based Wet -On- Wet Applicable on Exterior Painting System for LHB Types Coaches.

Technical Specification for PU based Wet -On- Wet Applicable on Exterior Painting System for LHB Types Coaches.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 ((Anti Graffiti test ASTM D-6578))	5000.0

118

CUSTOM PAINT ONSITE TESTING-1 (2024) - CUSTOM PAINT ONSITE TESTING-1

CUSTOM PAINT ONSITE TESTING-1

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Distinctness of Image (DOI))	10000.0

119

IRC 105 (2019) - SPECIFICATIONS FOR DENSE BITUMINOUS MACADAM AND BITUMINOUS CONCRETE FOR AIRFIELD PAVEMENTS

SPECIFICATIONS FOR DENSE BITUMINOUS MACADAM AND BITUMINOUS CONCRETE FOR AIRFIELD PAVEMENTS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 3.5 (Durability [ Soundness (Sodium sulphate )], %)	2000.0
Table 3.5 (Durability [Soundness (Magnesium or Sodium Sulphate )], %)	2000.0
Table 3.5 (Particle Shape (Combined Flakiness and Elongation Index), %)	3000.0
Table 3.5 (Strength [Los Angeles Abrasion Value], %)	1500.0
Table 3.5 (Strength [Aggregate Impact Value], %)	1500.0
2 (Density of DAC (On lines of ASTM D 2726))	2000.0
2 (Density of DBM (On lines of ASTM D 2726))	2000.0

120

ASTM B117 Salt spray - ASTM B 117 Salt spray Test For 96 hrs

ASTM B 117 Salt spray Test For 96 hrs

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

First
Prev
3
4
5
6
Next
Last