NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1274 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

691

IS 1148 (2009) - Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

Steel Rivet Bars (medium And High Tensile)--For Structural Purposes--For Structural Purposes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13 (Shear Test (Medium Tensile Steel))	3000.0
9 (Diameter of Bar (Over 24mm))	500.0
6 (Carbon)	500.0
6 (Sulphur)	500.0
6 (Phosphorus)	500.0

692

CUSTOM-02-ER-MCALI - Calibration of Test Ring (Ketos)

Calibration of Test Ring (Ketos)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension)	4000.0

693

IS 12118(Part 1):1987 - Specification for Two-Part Polysulphide-based Sealants

Specification for Two-Part Polysulphide-based Sealants

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1.1.1 (Rheological Properties-Pouring grade sealants)	1000.0
5.1.1.2 (Rheological Properties-Gun grade sealant)	5000.0
5.1.2 (Plastic deformation)	1500.0
5.1.3 (Adhesion and Tensile modulus)	5000.0
5.1.5 (Adhesion in Peel)	2500.0
5.1.6 (Loss of Mass after heat ageing)	1500.0
5.1.7 (Staining)	600.0
5.1.4 (Application life)	1500.0

694

ASTM A572 (2007) - Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel

Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6 (Yield Point)	2000.0
6 (Tensile Strength)	2000.0
6 (Elongation)	1000.0

695

IS 2590 - SPECIFICATION FOR PRIMARY ALUMINIUM INGOTS FOR REMELTING FOR GENERAL ENGINEERING PURPOSES

SPECIFICATION FOR PRIMARY ALUMINIUM INGOTS FOR REMELTING FOR GENERAL ENGINEERING PURPOSES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.1 i (Aluminium,)	1200.0
6.1 ii (Copper)	1200.0
6.1 iii (Silicon)	1200.0
6.1 iv (Iron)	1200.0
6.1 v (Manganese)	1200.0
vi (Zinc)	1200.0
6.1 vii (Titanium + Vanadium)	2400.0

696

IS 5666 (1970 RA 2019) - Etch Primer

Etch Primer

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3 (Consistency)	1000.0
3.3.2. (Mixed Material)	500.0
3.4 (Viscosity)	1000.0
3.5.1 (Air Drying)	500.0
3.5.2 (Force Drying Force Dry for 15 min at temp 85 to 100 Deg c &allow to cool for 1 hrs at Room Temp)	500.0
3.6 (Finish)	200.0
3.7 (Fineness of Dispersion)	500.0
3.8 (Fitness to Take a Coat of Primer, Cellulose Finish)	500.0
3.9 (Keeping Quality (for Six Months))	4000.0

697

Customized IS:11673-1992 (1992) - Sodium Hypo Chlorite Specification

Sodium Hypo Chlorite Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.3 (Available Chlorine % by mass by Volume)	2000.0

698

IS 14246 (2024) - Continuously Pre-Painted Galvanized Steel Sheets and Strips

Continuously Pre-Painted Galvanized Steel Sheets and Strips

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2 (Bend Test)	1000.0
9 (Mass of Sheet)	1000.0
8 (SALT SPRAY TEST (CORROSION RESISTANCE))	50000.0
4.2 (Mass of Zinc Coating)	2000.0
4.3 (Paint Coating Thickness)	2000.0
6.3 (Pencil Hardness Test)	1000.0
6.4 (Impact Resistance Test)	1000.0
6.5 (Cross Hatch Test)	1000.0
4 (Chemical Analysis as per Is 513 (Part-1):2016)	2500.0
4 (Tensile strength, MPa)	1000.0
4 (Yield Stress, MPa)	1000.0
4 (% Elongation)	1000.0
9 (Base Metal Thickness)	500.0
9 (Total Coated Thickness (as received condition), mm)	500.0

699

EURAMET cg-2 (2011) - CALIBRATION OF GAUGE BLOCK COMPARATORS

CALIBRATION OF GAUGE BLOCK COMPARATORS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5 (Length)	15000.0

700

Custom equaliser valve upper casing - Equaliser valve upper casing

Equaliser valve upper casing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon %)	1000.0
2 (Manganese %)	1000.0
3 (Silicon %)	1000.0
4 (Chromium %)	1000.0
5 (Nickel %)	1000.0
6 (Copper %)	1000.0
7 (Magnesium %)	1000.0

701

FCO 1985 (as amended upto November 2023) - FCO 1985 (as amended upto October 2024)

FCO 1985 (as amended upto October 2024)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Total Nitrogen)	1000.0
2 (Ammoniacal Nitrogen)	1000.0
3 (Nitrate Nitrogen)	1000.0
4 (Urea Nitrogen)	1000.0
5 (Total phosphorous (as P2O5) percent by weight)	1000.0
6 (Water soluble phosphorous (as P2O5) percent by weight)	1000.0
7 (Available phosphorous (as P2O5) percent by weight)	1000.0
8 (Moisture percent by weight)	1000.0
9 (Sulphate Sulphur (as S))	1000.0
10 (Elemental Sulphur (as S) percent by weight)	1000.0
11 (Total elemental sulphur (as S), percent by weight)	1000.0
12 (Free acidity (as H2SO4) percent by weight)	1000.0
12 (Water soluble potassium as K2O, Percent by weight)	1000.0
13 (Particle size -material retained between 1mm and 4mm IS sieve)	1000.0
14 (Total Sulphur , Percent by weight)	1000.0
15 (Calcium Nitrate, Percent by weight)	1000.0
16 (Free phosphoric acid (as P2O5) percent by weight)	1000.0
17 (Magnesium as Mg , percent by weight)	1000.0
18 (Magnesium as MgO , percent by weight)	1000.0
19 (Magnesium as MgCl2, percent by weight)	1000.0
20 (Sodium as NaCl percent by weight)	1000.0
21 (Total Chlorides, as Cl percent by weight)	1000.0
22 (Matter insoluble in water, percent by weight)	1000.0
23 (pH of 5% solution)	1000.0
24 (As as As % by weight)	1000.0
25 (As as As2O3, % by weight)	1000.0
26 (Specific gravity at given temperature)	1000.0
27 (Biuret % by weight)	1000.0
28 (Particle size, percent retained between given IS sieves)	1000.0
29 (Manganese as Mn % by weight)	1000.0
30 (Zinc as Zn % by weight)	1000.0
31 (Zinc as Zn % by weight in the form of Zn EDTA)	1000.0
32 (Zinc as Zn % by weight in the form of Zn HEDP)	1000.0
33 (Iron/Fe as Fe % by weight in the form of FeHEDP)	1000.0
35 (Lead as Pb % by weight)	1000.0
36 (Cadmium as Cd % by weight)	1000.0
37 (Copper as Cu % by weight)	1000.0
38 (Iron as Fe % by weight)	1000.0
39 (Boron as B % by weight)	1000.0
40 (Calcium as Ca % by weight)	1000.0
12.1 (Molybdenum)	1000.0
55 (Fe as Fe-EDTA)	1000.0
56 (Appearance)	1000.0
1 (Total Nitrogen(ammoniacal and Urea)percent by weight)	1000.0
15 (Particle size-Minimum 90% of material shall be retained between 1mm and 4 mm IS sieve)	1000.0
1 (Carbon (% by mass))	1000.0
1 (Carbon : NItrogen ratio (C: N))	1000.0
1 (Bulk density)	1200.0
1 (Total organic carbon)	1200.0
1 (Manganese as Mn (% by mass))	1200.0
1 (Contamination level)	1200.0
1 (Efficiency Character)	1200.0
0 (Available Phosphorus (as P2O5),)	1000.0
0 (Colour)	1000.0
0 (Fluoride)	1000.0

702

IS 1321 : Part 1 (2003) - Sisal ropes – Specification Part 1 Untarred varieties (fourth revision)

Sisal ropes – Specification Part 1 Untarred varieties (fourth revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Identification of Fiber)	2000.0
5.2 (Count of the Yarn)	1000.0
5.3 (No of Yarns per Strand)	500.0
5.3 (Lay of Strand)	500.0
5.4 (No. of Strands in the Rope)	500.0
5.4 (Lay of Rope)	500.0
5.4.1 (Angle of Lay)	1000.0
5.5 (Percentage of Lubricant)	2000.0
5.6 (Zinc Content)	1000.0
5.6 (Copper Content.)	1000.0
6.1 (Mass of the Coil)	1000.0
6.2 (Pitch)	1000.0
6.3 (Length of the Coil)	1000.0
6.4 (Linear Density of Rope)	1000.0
6.4 (Breaking Strength Of Rope)	5000.0
6.5 (Diameter of Rope)	500.0

703

Custom-24-ER-LM - Pull out Test for Assembly

Pull out Test for Assembly

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Pull out Test for Assembly)	5000.0

704

Custom- Driers Pb,Mn,Cu,Co - Custom- Driers Pb,Mn,Cu,Co

Custom- Driers Pb,Mn,Cu,Co

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Lead ,percent by mass)	1200.0
2 (Cobalt, percent by mass)	1200.0
3 (Manganese percent by mass)	1200.0
4 (Copper percent by mass)	1200.0

705

IS 2372:2021 - Timber for Cooling Towers-Specification

Timber for Cooling Towers-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.T1.3 (Species of Timber)	5000.0
4.T1.4 (Permissible stress-Bending and Tension Along Grain, Extreme Fibre stress)	3000.0
5.1 (Grading of Timber & defects in timber)	5000.0
6 (Dimension and Tolerances)	1000.0
7 (Treatment (IS 401:2001))	4000.0
7.1 (Depth of Penetration of Preservative)	1000.0

706

1540 part-2 - QUICKLIME AND HYDRATED LIME FOR CHEMICAL INDUSTRIES SPECIFICATION

QUICKLIME AND HYDRATED LIME FOR CHEMICAL INDUSTRIES SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (ii) (Available lime [ as Ca (OH)2, percent by mass,)	2000.0

707

MDTS-207(REV.-5.2) (2022) - Technical Specification for Fire Retardant Fibre Glass Wool with Single Side Heat Resistant Aluminium Foil.

Technical Specification for Fire Retardant Fibre Glass Wool with Single Side Heat Resistant Aluminium Foil.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2.5 (Basis Weight)	1000.0
5.2.5 (Water Vapour Transmission Rate)	5000.0
5.2.5 (Bursting Strength)	2000.0
5.2.5 (Tensile Strength(Along Length))	2000.0
5.2.5 (Tensile Strength(Across the length))	2000.0
5.2.5 (Caliper Thickness)	1000.0
5.2.5 (Water immersion)	1000.0
5.2.5 (Mold Resistance)	3000.0
5.2.5 (Temperature resistant)	2000.0
5.2.5 (Dimension Stability)	2000.0

708

IS 5352 : Part 1 (1999) - Textile – Glass and glass-polyester fibre woven tapes Part 1 Specification (third revision)

Textile – Glass and glass-polyester fibre woven tapes Part 1 Specification (third revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Alkali percent as Sodium Oxide)	2000.0
5.1 (Identification of Yarn)	2000.0
5.2 (Weave)	500.0
5.3 (Locking Thread)	500.0
5.4 (Centre Marking)	500.0
5.5 (Identification of Types of Tapes)	500.0
6.1 (Thickness)	1000.0
6.2 (Width)	500.0
6.3 (Length)	500.0
6.4 (Tensile Strength)	2000.0
6.5 (Effect of heating in air)	3000.0
6.5 (Glass Content)	2000.0

709

DOLOMITE - Custom-DOlOMITE

Custom-DOlOMITE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Calcium, Percent by mass)	2000.0
2 (Magnesium, percent by mass)	2000.0

710

SCHEDULE OF REQUIREMENTS(SOR)/SCHOOL BAG/2024 (2024) - SCHEDULE OF REQUIREMENTS(SOR)/SCHOOL BAG/2024

SCHEDULE OF REQUIREMENTS(SOR)/SCHOOL BAG/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.1 (Colour of the Bag)	100.0
1.2 (Colour of the Front Pocket)	100.0
1.3 (Colour of the Shoulder Strip)	100.0
1.4 (Colour of the Adjustable Belt)	100.0
1.5 (Colour of the Beadings)	100.0
1.6 (Colour of the Shoulder Adjustable Buckle)	100.0
1.7 (Colour of the Water Bottle Pocket)	100.0
1.8 (Colour of the Zip)	100.0
1.9 (Colour of the Runner)	100.0
1.10 (Colour of the Top Handle)	100.0
2.1 (Length of Main Compartment)	100.0
2.1 (Breadth of Main Compartment)	100.0
2.1 (Depth of Main Compartment)	100.0
2.2 (Length of Front Pocket)	100.0
2.2 (Breadth of Front Pocket)	100.0
2.2 (Depth of Front Pocket)	100.0
2.3 (Length Of Shoulder Strap)	100.0
2.3 (Breadth Of Shoulder Strap)	100.0
2.3 (Material Specification of Shoulder Strap)	500.0
2.4 (Length of Water Bottle Pocket)	100.0
2.4 (Breadth of Water Bottle Pocket)	100.0
2.4 (Material Specification of Water Bottle Pocket)	500.0
3.1 (Length of Zip(Main Compartment))	100.0
3.2 (Zip No.(Front Pocket))	100.0
4.0 (Length of Runner Handle)	100.0
4.0 (Width of Runner Handle)	100.0
5.0 (Length of Top Handle)	100.0
5.0 (Width of Top Handle)	100.0
6.0 (Length Of Adjustable Belt)	100.0
6.0 (Breadth Of Adjustable Belt)	100.0
6.0 (Thickness Of Adjustable Belt)	100.0
8.1 (Identifiction of Outer Layer)	500.0
8.1 (GSM of Outer Layer)	500.0
8.2 (Identification of Cushion Foam)	500.0
8.2 (Thickness of Cushion Foam)	100.0
8.3 (Identification of Zip)	500.0
8.4 (Identification of NET)	500.0
8.5 (Identification of Adjustable Belt)	500.0
8.5 (Weight of Adjustable Belt)	1000.0
8.6 (Identification of Shoulder Adjustable Buckle)	500.0
8.6 (Breaking Load of Shoulder Adjustable Buckle)	500.0
8.7 (Identification of Thread)	500.0
8.8 (Breaking Strength of Main Fabric Body(Warp))	1000.0
8.8 (Breaking Strength of Main Fabric Body(Weft))	1000.0
8.8 (Tear Strength of Main Fabric Body(Warp))	1000.0
8.8 (Tear Strength of Main Fabric Body(Weft))	1000.0
8.10 (Drop Test)	1000.0
8.11 (No. of Stitches per 25 mm)	100.0
8.12 (Lining Material)	500.0
8.13 (Snatch Test)	1000.0

711

Custom/Steel Cord Conveyor Belt/2026 (2026) - Steel Cord Conveyor Belt For Hoisting and Conveying

Steel Cord Conveyor Belt For Hoisting and Conveying

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Firm's request. (Pull-Out Force of the Cord)	3000.0
Firm's request. (Strip Resistance Between Cover Rubber & Core Rubber)	4000.0
Firm's request. (Tensile Strength of Cover Rubber)	2000.0
Firm's request. (Elongation of Cover Rubber)	1000.0
Firm's request. (Change in Tensile Strength of Cover After Ageing (at 70 deg.C for 168 hrs.))	3000.0
Firm's request. (Change in Elongation of Cover After Ageing (at 70 deg.C for 168 hrs.))	2000.0
Firm's request (Abrasion Loss)	3000.0
Firm's request (Hardness (Shore A))	1000.0
Firm's request (Tear Strength of Cover Rubber)	4000.0
Firm's request (Flame Test)	4000.0
Firm's request (Electrical Resistivity)	5000.0
Firm's request. (Cord-Pull Out Force After Thermic Treatment)	3000.0
Firm's request (Change in Tensile Strength of Cover After Ageing (at 70 deg.C for 72 hrs.))	3000.0
Firm's request (Change in Elongation of Cover After Ageing (at 70 deg.C for 72 hrs.))	2000.0

712

IS 12744 (2013 RA 2018) - Ready Mixed Paint, Air Drying, Red Oxide - Zinc Phosphate, Priming - Specification ( For Domestic and Decorative Applications)

Ready Mixed Paint, Air Drying, Red Oxide - Zinc Phosphate, Priming - Specification ( For Domestic and Decorative Applications)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Lead Restriction(Lead as Metallic Lead))	2000.0
5.3 Table 1(i) (Drying Time ,Hard Dry in hours)	500.0
5.3 Table 1(ii) (Consistency)	100.0
5.3 Table 1(iii) (Finish)	200.0
5.3 Table 1(iv) (colour in Natural Daylight)	1200.0
5.3 Table 1(v) (Wet opacity meter square per liter)	1200.0
5.3 Table 1(vi) (Pigment content, percent by mass)	2100.0
5.3 Table 1(vii) (Zinc phosphate ,percent by mass on pigment (annex C))	3500.0
5.3 Table 1(viii) (Red Oxide (as Fe2O3),percent by mass on pigment)	2500.0
5.3 Table 1(ix)a (Flexibility and adhesion a) Scratch hardness (Load 800 g))	2000.0
5.3 Table 1(ix) b (Flexibility and adhesion b) Bend test (with 6.25 mm dia mandrel in type 1 apparatus))	1200.0
5.3 Table 1(x) a (Resistance to humidity under conditions of condensation: a) Resistance to humidity (for 7 days))	2500.0
5.3 Table 1(x)b (Resistance to humidity under conditions of condensation: b) Resistance to salt spray to (for96 hours))	2500.0
5.3 Table 1(ix) (Flash point, Deg C)	2000.0
5.3 Table 1(xii) (Mass in kg/10 ltrs)	1500.0
5.3 Table 1(xiii) (Keeping properties (for 12 months ))	10000.0

713

NTH ER PAINT EXTERIOR PERFORMANCE (2022) - NTH ER PAINT EXTERIOR PERFORMANCE

NTH ER PAINT EXTERIOR PERFORMANCE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Water Vapor Permeability Test- ASTM D1653)	4500.0
2 (QUV test for 300 hours Fluorescent UV-Condensation Exposures of Paint ASTM D4587)	15000.0
3 (QUV test for 200 hours Fluorescent UV-Condensation Exposures of Paint ASTM D4587)	10000.0
4 (Tensile Strength- ASTM D638)	2000.0
5 (Elongation @ Break- ASTM D638)	1000.0
6 (Pull off Adhesion test (ASTM D 4541) on concrete Substrate)	2000.0
7 (QUV test for 500 hours Fluorescent UV-Condensation Exposures of Paint ASTM D4587)	25000.0

714

IS 17545: 2021 (2021) - WHITE CEMENT BASED POLYMERIC PUTTY

WHITE CEMENT BASED POLYMERIC PUTTY

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.1 (FORM &CONDITION)	100.0
4.2 (Composition)	100.0
4.3 (Consistency)	100.0
4.4 (Lead Restriction ( as metallic lead))	1000.0
4.5 Table 1(i) (Tensile adhesion strength (avg. of min 3 readings) @14 days, N/mm2,)	2500.0
4.5 Table 1(ii) (Water retentivity, percent)	1000.0
4.5 Table 1(iii) (Initial Setting time-Annex D in minutes)	200.0
4.5 Table 1(iii) (Final Setting time-Annex D in minutes)	200.0
4.5 Table 1(iv) (Polymer content (based on loss on ignition), percent by mass)	1000.0
4.5 Table 1(vi) (Cement content, percent Annex B of IS 5410)	1200.0
4.6 Optional requirement (Compressive strength, 28 days in N/mm2 (IS 4031 (Part 6)))	3000.0
4.5 Table 1(v) (Degree of whiteness, percent)	1200.0

715

IS 3589 (2001) - Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
11 (Dimension (Diameter))	1000.0
9.1 (Tensile Strength)	1000.0
9.1 (Yield Strength)	1000.0
9.1 (Elongation)	1000.0
12.5 (Straightness)	1000.0
9.2 (Flattening test)	1000.0
11 (Weight)	1000.0
8.1 (Carbon)	500.0
8.1 (Sulphur)	500.0
8.1 (Phosphorus)	500.0
8.1 (Manganese)	1000.0
14 (Visual Inspection, Apperance and Workman ship)	1000.0
8.1 (Carbon Equivalent)	2000.0

716

8183 - Bonded Mineral wool-Specification

Bonded Mineral wool-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.10.1 (Resistance to microorganisms)	3000.0

717

IS 3448 (2014) - Rice bran oil - Specification (Third Revision)

Rice bran oil - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.7 i (Moisture and insoluble impurities, percent by mass)	1000.0
5.7 ii (Colour in a 1 inch cell on the Lovibond scale, expressed as (Y + 5R))	1000.0
5.7 iii (Refractive index at 40ºC)	1000.0
5.7 iv (Specific gravity at 30º/30ºC)	1000.0
5.7 v (Saponification value)	1000.0
5.7 vi (Iodine value (Wijs))	1000.0
5.7 vii (Acid value,)	1000.0
5.7 viii (Unsaponifiable matter, percent by mass)	1000.0
5.1 (Description)	1000.0
5.2.1 (Clarity)	1000.0
5.3 (Test for presence of Argemone oil)	1000.0
5.3 (Test for presence of Castor oil)	1000.0
5.3 (Test for presence of Hydrocyanic acid)	1000.0
5.3 (Test for presence of MIneral oil)	1000.0
5.3 (Test for presence of Karanja oil)	1000.0
5.3 (Test for presence of kusum oil and other oils containing cyanogenic compounds)	1000.0
5.3 (Test for presence of neem oil)	1000.0

718

IS 12866 (2021) - Plastic Translucent Sheets made from Thermo-Setting Polyester Resin Glassfibre Reinforced - Specification

Plastic Translucent Sheets made from Thermo-Setting Polyester Resin Glassfibre Reinforced - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.8 (Light Transmission, percent)	2000.0
6.6 (Load Deflection Test.)	8000.0
6.5 (Bolt Shear Test.)	2000.0
6.3 (Water Absorption, percent)	1000.0
6.2 (Glass Content, percent)	3000.0
6.1 (Mass per unit area)	1000.0
4.6 (Pitch of Corrugation, mm)	1000.0
4.5 (Depth of Corrugation, mm)	1000.0
4.2 (Minimum Thickness, mm)	1000.0
4.1 (Overall Width, mm)	1000.0
Firm's Request (Exposure to UV Light(24-hrs))	1200.0
Firm's request. (Density)	1000.0

719

Customer Specification- High Voltage Test - Customer Specification- High Voltage Test

Customer Specification- High Voltage Test

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
AC High Voltage test (AC High Voltage test)	5000.0

720

IEC 60571 (2012) - Railway applications – Electronic equipment used on rolling stock

Railway applications – Electronic equipment used on rolling stock

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.2.6 (Damp heat test, cyclic (Up to 48 Hrs))	20000.0
12.2.6 (Damp Heat Cyclic Test (Up to 24 Hrs))	10000.0
12.2.5 (Dry Heat Test ( Upto 24 Hrs))	10000.0
12.2.5 (Dry Heat Test ( Upto 48 Hrs))	20000.0
12.2.4 (Cold Start Test (Up to 24 Hrs))	10000.0
12.2.4 (Cold Start Test (Up to 48 Hrs))	20000.0