NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1252 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

631

MORTH 5th Revision table 900-4/IRC:111-2009 - Dense bituminous macadam/bituminous concrete-Specification for dense graded bitumen mixes

Dense bituminous macadam/bituminous concrete-Specification for dense graded bitumen mixes

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
505.3.5 (Density(ASTM-D2726))	2000.0
505.3.5 (GMM(ASTM-D2041))	3000.0
505.3.5 (Compaction in %(ASTM-D2041))	5000.0
505.3.5 (Binder content(ASTM-D 2172))	5000.0

632

MORTH/ASTM - Mix Macadam

Mix Macadam

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
406.2.1.1 (Water absorption)	1000.0
406.2.1.1 (Soundness)	2000.0
406.2.1.1 Table 400.12.1 (Los Angeles Abrasion value)	1500.0
406.2.1.1 Table 400.12.1 (Aggregate Impact value)	1500.0
406.2.1.1 Table 400.12.2 (Combined Flakiness and Elongation Indices (Total))	3000.0
406.2.1.2 Table 400.13 (Grading Requirements of Aggregates for Wet Mix Macadam)	5000.0
406.2.1.2 (Plasticity Index (PI))	1000.0
406.2.1.2 (Liquid Limit)	1000.0
406.2.1.2 (Plastic Limit)	1000.0

633

ISKCON Sri Mayapur Chandrodya Mandir TOVP ISKCON (2023) - ISKCON Sri Mayapur Chandrodya Mandir TOVP ISKCON

ISKCON Sri Mayapur Chandrodya Mandir TOVP ISKCON

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Durability Test- Accelerated Weathering Test (QUV 4 hours and 4 hours condensation alternatively, Temp. 50°C, 500 hours))	24000.0
2 (Gloss Value at 60 deg&45 deg angle a)Before Exposure b) after exposure c)Gloss retention %)	1000.0
3 (Resistance to salt spray(5% Nacl Solution) 500 hours ASTM B 117)	25000.0

634

IS 516 (Part 1/Sec 1) : 2021 (3 set CC cubes) - Hardened Concrete —Methods of Test (Part 1 Testing of Strength of Hardened Concrete) (Section 1 Compressive, Flexural and Split Tensile Strength)

Hardened Concrete —Methods of Test (Part 1 Testing of Strength of Hardened Concrete) (Section 1 Compressive, Flexural and Split Tensile Strength)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3 (Compressive strength,MPa)	3600.0

635

2386 (WMM) (1963) - Wet Mix Macadum

Wet Mix Macadum

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

636

MORTH-5th Revision 2013 Sub Base, Bases (Non Bituminous) - Specifications for Road and Bridge Works

Specifications for Road and Bridge Works

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Section 400 of MoRTH GSB/WBM/WMM/Screening/CRM etc. (Table 400-1/9/10/13/14 etc.). (Grading(as per Table 400 section of Morth 5th revision))	5000.0
401.2.2 (Water absorption)	1000.0
Section 400 of MoRTH GSB/WBM/WMM/CRM etc. (Table 400-2/8/1215 etc.). (Aggregate Impact value)	1500.0
Section 400 of MoRTH GSB/CRM etc. (Table 400-2/15 etc.). (Liquid limit)	1000.0
Section 400 of MoRTH GSB/CRM etc. (Table 400-2/15 etc.). (Plasticity Index)	2000.0
401.2.2 Table 400.2 (CBR)	6000.0

637

NTH/ER/CHEM/CUST-02 BS 476 ASTM E 119 (22) - AS PER CUSTOMER REQUIRMENTS FIRE RESISTANCE TEST

AS PER CUSTOMER REQUIRMENTS FIRE RESISTANCE TEST

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Fire Resistance Test: 1.Stability)	2000.0
2 (Fire Resistance Test: 2.Integrity)	2000.0
3 (Fire Resistance Test:3. Insulation)	1000.0
4 (Fire Resistance Test:4 Fire resistance Properties)	2000.0
5 (Fire Resistance Test:5 Self –Extinguished Properties)	2000.0
6 (Fire Resistance Test: 6 Peel Off after 120 /240 min Fire test)	1000.0

638

NTH/NR/CHEM/CUST-02 ASTME 119/BS 476 (As per Pt: 20 and 24) - As per Customer Requirement

As per Customer Requirement

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

639

Custom - Kiln Bricks / Fused Alumina

Kiln Bricks / Fused Alumina

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Fe2O3, Percent by mass)	2000.0
2 (Al2O3, Percent by mass)	2000.0

640

CUSTOM/EAR TAG/2022 (2022) - CUSTOM/EAR TAG/2022

CUSTOM/EAR TAG/2022

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Pull Test Force)	2000.0
2.0 (Material Identification)	5000.0
3.0 (Weight of Male BTM and Female Tag)	2000.0
4.0 (Dimension of Tag(Male & female))	1000.0

641

NTHER-Calibration of Digital DC Power Supply - NTHER-Calibration of Digital DC Power Supply

NTHER-Calibration of Digital DC Power Supply

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Calibration of Digital DC Power Supply upto 100V,150A)	5000.0
A2 (Calibration of Digital DC Power Supply upto 100V,20A)	2500.0
A3 (Calibration of Digital DC Power Supply upto 50V,40A)	3500.0
A4 (Calibration of Digital DC Power Supply upto 40V,25A)	3000.0

642

NTHER-Calibration of Programmable DC Electronics Load - NTHER-Calibration of Programmable DC Electronics Load

NTHER-Calibration of Programmable DC Electronics Load

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (NTHER-Calibration of Programmable DC Electronics Load)	4000.0

643

NTHER-Calibration of Data Acquisition Chart Recorder - NTHER-Calibration of Data Acquisition Chart Recorder

NTHER-Calibration of Data Acquisition Chart Recorder

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (NTHER-Calibration of Data Acquisition Chart Recorder (32 Channel))	5000.0
A2 (NTHER-Calibration of Data Acquisition Chart Recorder (16 Channel))	4000.0
A3 (NTHER-Calibration of Data Acquisition Chart Recorder (8 Channel))	3000.0

644

IRS-T-46-2023 (2023) - INDIAN RAILWAY STANDARD SPECIFICATION FOR SPHEROIDAL GRAPHITE CAST IRON INSERTS

INDIAN RAILWAY STANDARD SPECIFICATION FOR SPHEROIDAL GRAPHITE CAST IRON INSERTS

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.5 (Carbon (C))	500.0
7.5 (Manganese (Mn))	500.0
11.2 (Phosphorus (P))	500.0
7.5 (Sulphur (S))	500.0
7.5 (Silicon (Si))	500.0
11.4 (Tensile Strength)	2000.0
11.4 (% Elongation)	1000.0
11.5 (Brinell Hardness)	2000.0
11.6 (Microstructure)	3000.0
13 (Weight)	1000.0
11.2 (Tin (Sn))	500.0
11.2 (Copper (Cu))	500.0

645

IRS T-46 (1996) - Indian Railway Standard Specification For Spheroidal Graphite Cast Iron Inserts

Indian Railway Standard Specification For Spheroidal Graphite Cast Iron Inserts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
13 (Weight)	1000.0
12 (Dimensions)	1000.0
11.7 (Internal Soundness)	1000.0
11.6 (Micro Structure)	2000.0
11.5 (Brinell Hardness)	2000.0
11.4 (Elongation)	3000.0
11.4 (Tensile Strength)	3000.0
11.2 (Chemical Composition)	2500.0

646

ISO 683-17 (2014) - Heat-treated steels, alloy steels and free-cutting steels —Ball and roller bearing steels

Heat-treated steels, alloy steels and free-cutting steels —Ball and roller bearing steels

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1.2 (Carbon)	500.0
7.1.2 (Silicon)	500.0
7.1.2 (Manganese)	500.0
7.1.2 (Phosphorus)	500.0
7.1.2 (Sulphur)	500.0
7.1.2 (Chromium)	500.0
7.1.2 (Molybdenum)	500.0
7.1.2 (Copper)	500.0
7.1.2 (Aluminium)	500.0
7.1.2 (Nickel)	500.0
7.1.2 (Vanadium)	500.0
7.1.2 (Lead)	500.0
7.1.4 (Hardness)	2000.0
7.5.1 (Visual Inspection)	1000.0

647

RCF Spec. No. EDTS-163,Rev. C - RCF Spec. No. EDTS-163,Rev. C

RCF Spec. No. EDTS-163,Rev. C

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.4.c (IP Protection Test)	15000.0
7.4.f (Vibration and shock test)	70000.0
7.4.f (Impact Test)	15000.0

648

NTHER-Calibration of HV Probe - NTHER-Calibration of HV Probe

NTHER-Calibration of HV Probe

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (NTHER-Calibration of HV Probe upto 40 kV)	4000.0
A2 (NTHER-Calibration of HV Probe upto 80 kV)	7000.0

649

Custom: Bright bar

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Carbon % by mass)	1200.0
2 (Silicon % by mass)	1200.0
3 (Manganese % by mass)	1200.0
4 (Sulphur % by mass)	1200.0
5 (Phosphorus % by mass)	1200.0
6 (Lead % by mass)	1200.0

650

AWWA C210-15 (2015) - Solvent Free Liquid epoxy Coating (Red / Grey) for steel Water pipeline &Fittings Internal

Solvent Free Liquid epoxy Coating (Red / Grey) for steel Water pipeline &Fittings Internal

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 1 Prequalification Requirements a) (Immersion and vapour resistance test for 30 days in: 1. Deionized Water (ANSI/ AWWA C 210-2015 Clause No. 5.2.1.1--ASTM D 6943))	3000.0
Table 1 Prequalification Requirements b) (Immersion and vapour resistance test for 30 days in: 2. Sulphuric Acid,1% by weight ANSI/ AWWA C 210-2015 Clause No. 5.2.1.1-ASTM D 6943)	3000.0
Table 1 Prequalification Requirements c) (Immersion and vapour resistance test for 30 days in: 3.Sodium Hydroxide, 1% by weight ANSI/ AWWA C 210-2015 Clause No. 5.2.1.1-ASTM D 6943)	3000.0
Table 1 2 Prequalification Requirements (Cathodic disbondment test, 28 days, -1.5V AWWA C 210 Clause No. 5.2.1.2 /*ASTM G 8)	5000.0
Table 1 3.Prequalification Requirements (Dielectric Strength AWWA C 210-2015 Clause No. 5.2.1.3/ASTM D 149)	10000.0
Quality Control Requirements Table 2 1 (Appearance AWWA C 210-2015 Clause No. 5.5.1)	100.0
Quality Control Requirements .2 Table 2 (Cure test AWWA C 210-2015 Clause No. 5.5.2/ASTM D 5402)	1000.0
Quality Control Requirements 3 Table 2 (Dry Film Thickness AWWA C 210-2015 Clause No. 5.5.3)	1000.0
Quality Control Requirements 4 Table 2 (Adhesion to steel (Pull Adhesion to steel (Pull Off Adhesion test) ASTM D 4541)	5000.0
Quality Control Requirements 5. Table 2 (Electrical Continuity Inspection / (Pin-hole detector @ 2.5 KV))	5000.0
Quality Control Requirements (Abrasion resistance - 'Abrasion resistance of organic coatings by the Taber Abraser" - 1 kg load / 1000 cycles CS 17 wheel or CS 10 wheel ASTM D4060)	5000.0
Quality Control Requirements (Shore D hardness "ASTM D2240 ")	1200.0
Quality Control Requirements (Compressive Strength "ASTM C109 ")	5000.0
ADD PARAMETER 1 (Potable Water Service test a)PH on the lines of IS 10500)	1000.0
additional parameter (Potable Water Service test b)Turbidity on the lines of IS 10500)	1000.0
additional parameter (Potable Water Service test d)Chloride on the lines of IS 10500)	1000.0
additional parameter (Potable Water Service test c)Total hardness on the lines of IS 10500)	1000.0
additional parameter (Potable Water Service test e)Nitrate on the lines of IS 10500)	1000.0
additional parameter (Potable Water Service test f)Iron on the lines of IS 10500)	1000.0
additional parameter (Potable Water Service test g)Arsenic on the lines of IS 10500)	1000.0
additional parameter (Potable Water Service test h)Fluoride on the lines of IS 10500)	1000.0
1.1 (Specific Gravity (after Mixing Comp A+ Comp B))	1000.0
additional parameter (Abrasion Resistance 1560Cycle/mill as per ASTM D4060)	5000.0
additional parameter (Adhesion to steel)	1200.0

651

AAI BAGDOGRA AIRPORT SPECIFICATION (2023) - AAI BAGDOGRA AIRPORT SPECIFICATION

AAI BAGDOGRA AIRPORT SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A (Thickness of ACP)	1000.0
A (Thickness of Aluminium Coil)	1000.0
B (Tensile Strength)	1000.0
B (Yield Strength)	1000.0
B (Elongation)	1000.0
F (Bend Test)	2000.0
C Paint Performance 1 (Specular gloss 60 degree angle ASTM 523/4214)	1000.0
C PAINT Performance 2 (Thickness of coating in microns)	1000.0
C PAINT Performance 3 (Pencil Hardness test(11 ,11 B) ASTM 3363)	1000.0
C PAINT Performance 4 (Impact Resistance ASTM D 2794)	2000.0
D FIRE RESISTING BEHAVIOUR 3 (Surface Spread of Flame (BS 476 Part VII))	5000.0
E chemical &aging test 1 (chemical & Aging Test 1)Weathering & Conditioning test(ASTM D 2247) for 24 Hours)	2000.0
E chemical &aging test 2 (chemical & Aging Test Salt Spray test for 500 hours(ISO 9227))	20000.0
E chemical &aging test 2 (chemical & Aging Test Salt Spray test for 3000 hours(ISO 9227))	100000.0
E chemical &aging test 3 (Resistance to 5%(V/V)Hydrochloric acid solution for 24 hours)	1000.0
E chemical &aging test 3 (Resistance to 5%(V/V)H2SO4 acid solution for 24 hours)	1000.0

652

Custom moisture-coal tar - Custom moisture-coal tar

Custom moisture-coal tar

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Moisture, percent by mass)	1200.0

653

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA) [1100 kVA to 2 500 kVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) (1100 kVA to 2 500 kVA)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.2(a) (Measurement of Winding Resistance)	1000.0
21.2(b) (Measurement of voltage ratio and,check ofvoltage vector relationship)	2000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	20000.0
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	20000.0
21.3(b) (Temperatur Rise Test)	40000.0
21.2(g) (Separate Source AC voltage withstand test)	2500.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	5000.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	7000.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	1500.0
21.2(c) (Measurement of impedance voltage (principal tapping), shortcurcuit impedance and load loss (At 50% and 100% load))	8000.0
21.2(d) (Measurement of no Load and loss and current)	6000.0
21.2(f) (lnduced Over Voltage withstand test)	4000.0
21.4(a) (Determination of sound levels)	7000.0
21.4( e) (BDV of Oil in the tranformer)	10000.0
21.5.1.121.5.2.121.5.3.1 (Air Pressure (Type test)-Deflection)	20000.0
21.5.2.1 (Permanent Deflection)	20000.0
21.4( e) (Break Down Voltage)	10000.0
21.2(f) (lnduced Over Voltage withstand test)	4000.0
21.2(d) (No Load loss and current)	6000.0
21.2(c) (Load Loss and % Impedance)	8000.0
21.2(e) (Insulation Resistance)	1500.0
21.4( c) (No load current)	2000.0
8.9 (flux density and over fluxing)	20000.0
7.9 (flux density and over fluxing)	10000.0
21.5.3.3 (Oil leakage test)	5000.0
21.2(g) (AC High Voltage Withstand Test)	2500.0
21.3(b) (Temperature Rise of Oil and Windings.)	40000.0
21.5.3.1 (Permanent Deflection)	6000.0
21.4(a) (Determination of sound levels)	7000.0
As per CBIP Pub No. 317 Cl. 3.17 (Magnetic Balance Test)	5000.0
As per CBIP Manual No. 317 Cl. (Harmonics of No-load Current)	15000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	5000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	5000.0
N.A. (Unbalance Current)	5000.0
CBIP Publication no. 317 (Polarization Index)	2500.0

654

IRS:S63-2014 - PVC Insulated Underground, Unscreened Cable for Railway Signalling- Power Cable

PVC Insulated Underground, Unscreened Cable for Railway Signalling- Power Cable

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.6.1 (Physical tests for conductor-Dimension)	1000.0
5.6.2 (Physical tests for conductor-Annealing Test)	2000.0
5.6.3 (Physical tests for conductor-Test for correspondence of cores)	1000.0
5.7 (Conductor Resistance Test)	2000.0
5.8.1 (Test for Armour wires/strips/tapes-Dimension)	1000.0
5.8.2 (Test for Armour wires/strips/tapes- Tensile Strength and Percentage Elongation Test)	2000.0
5.8.3 (Test for Armour wires/strips/tapes-Torsion Test (for Round wires only))	1000.0
5.8.4 (Test for Armour wires/strips/tapes-Winding Test(For Galvanised strips only))	2000.0
5.8.5(i)(a) (Test for Armour wires/strips/tapes-Tests for mass of Zinc Coating)	1000.0
5.8.5(i)(b) (Test for Armour wires/strips/tapes-Tests for uniformity of Zinc Coating)	1000.0
5.8.6 (Test for Armour wires/strips/tapes-Resistivity Test)	2000.0
5.8.7 (Test for Armour wires/strips/tapes-Test for closeness of armour wires/strips)	1000.0
5.9 (Test for thickness of insulation and sheath)	1000.0
5.10.1(i) (Physical tests for insulation,inner & outer sheaths-Tensile strength and elongation at break)	2000.0
5.10.2 (Physical tests for insulation,inner & outer sheaths-Shrinkage Test)	1000.0
5.10.3 (Physical tests for insulation,inner & outer sheaths-Hot deformation test)	1000.0
5.10.4 (Physical tests for insulation,inner & outer sheaths-Loss of mass test)	2000.0
5.10.5 (Physical tests for insulation,inner & outer sheaths-Colour fastness to day-light exposure)	2000.0
5.10.6 (Physical tests for insulation,inner & outer sheaths-Colour fastness to water)	1000.0
5.10.7 (Physical tests for insulation,inner & outer sheaths-Bleeding and blooming Test)	1000.0
5.10.8 (Physical tests for insulation,inner & outer sheaths-Cold bend test)	2000.0
5.10.9 (Physical tests for insulation,inner & outer sheaths-Cold impact test)	2000.0
5.10.10 (Physical tests for insulation,inner & outer sheaths-Heat shock test)	2000.0
5.10.11 (Physical tests for insulation,inner & outer sheaths-Thermal stability test)	2000.0
5.10.12 (Physical tests for insulation,inner & outer sheaths-Specific Gravity test for PVC)	1000.0
5.11 (Flammability Test)	2000.0
5.12 (High Voltage Test)	3000.0
5.13 (Insulation resistance test)	2000.0
5.14.1 (Water immersion-AC Test)	3000.0
5.15 (Visual inspection test-)	1000.0
5.9 (Test for thickness of insulation and sheath)	1000.0

655

IS 2645:2003 (RA 2017) - Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

Integral Waterproofing Compounds for Cement Mortar and Concrete-Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.2.a. (Setting time -Initial)	500.0
3.2.b (Setting time-Final)	500.0
3.3.a (Compressive strength-3 days)	2000.0
3.3.b (Compressive strength-7 days)	2000.0
3.4 (Chloride content)	2000.0
- (Appearance)	1000.0
- (Bulk density)	1000.0
- (pH)	1000.0

656

IS 2645 (2003) - Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.3.b (Compressive Strength-7days)	2000.0
3.3.a (Compressive Strength-3 days)	2000.0
3.2.b (Setting Time (Final Setting Time))	500.0
3.2.a (Setting Time (Initial Setting Time))	500.0
3.4 (Chloride Content, %)	1000.0

657

JIS D 5302-2004 - Lead Acid Batteries for Motorcycles

Lead Acid Batteries for Motorcycles

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.3.2 (Capacity (10 hour rate))	25000.0
8.3.3 (High Rate Discharge test)	15000.0
8.3.4 (Vibration resistance)	20000.0
Reference 1 (Deep Cycle Endurance)	60000.0
Reference 2 (Shallow Cycle Endurance)	60000.0
Reference 3 (Characteristics of Electrolyte Decrease)	30000.0
Reference 4 (Charge Retention test)	20000.0
8.3.1 (Dimensions)	1000.0

658

JISC 8702 : 2009 - Small- sized valve regulated lead-acid batteries

Small- sized valve regulated lead-acid batteries

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 of JISC 8702-2:2009 (Dimensions)	500.0
5.1 of JISC 8702-1:2009 (Capacity at 20 hr rate)	20000.0
5.2 of JISC 8702-1:2009 (High rate discharge characteristics)	20000.0
5.3 of JISC 8702-1:2009 (Cycle service Endurance)	200000.0
5.4 of JISC 8702-1:2009 (Storage characteristic Test)	20000.0
5.5 of JISC 8702-1:2009 (Maximum permissible current Characteristic)	15000.0
5.6 of JISC 8702-1:2009 (Charge Acceptance characteristic after deep discharge.)	15000.0
5.7 of JISC 8702-1:2009 (Endurance in Trickle application)	100000.0
5.8 of JISC 8702-1:2009 (Endurance in trickle application at 40 Deg C)	130000.0
5.9.a of JISC 8702-1:2009 (Gas Emission Intensity I)	15000.0
5.10.a of JISC 8702-1:2009 (Gas recombinating characteristic - operation of vent valve)	15000.0
5.11 of JISC 8702-1:2009 (Vibration Resistance Characteristics)	15000.0
7.12 of JISC 8702-1:2009 (Shock Resistance Characteristics)	15000.0
7.1.b (Actual Capacity at the 1 hour discharge rate)	20000.0
5.10.b of JISC 8702-1:2009 (Gas recombinating characteristic - Liquid leakage resistance characteristics)	15000.0
5.9.b of JISC 8702-1:2009 (Gas emission intensity II)	15000.0

659

CQAL/637 :2006 - SPECIFICATION FOR BATTERY SECONDARY, LEAD ACID, LOW MAINTENANCE FOR MT PURPOSES

SPECIFICATION FOR BATTERY SECONDARY, LEAD ACID, LOW MAINTENANCE FOR MT PURPOSES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1 (Visual Examination)	1000.0
15.2 (Physical Examination)	1000.0
15.3 (Dimensions and Layout)	1000.0
15.4 (Marking)	1000.0
15.5 (Capacity (5-h rate))	5000.0
15.6.1 (High Rate Discharge at -15 degree C)	10000.0
15.6.3 (High Rate Discharge at Normal Temperature)	15000.0
15.7 (Robustness of Handle)	5000.0
15.8 (Charge Acceptance)	15000.0
15.9 (Air Pressure Test)	10000.0
15.10 (Life Cycle test)	100000.0
15.11 (Vibration Resistance)	10000.0
15.12 (Over Charge Endurance)	20000.0
15.13 (Strength of Terminal)	5000.0
15.14 (Robustness to Fastening)	5000.0
15.15 (Test for Dry Charged Battery)	10000.0
15.16 (High Voltage Test)	5000.0
15.17 (Retention of Charge)	15000.0
15.18 (Electrolyte Retention test)	5000.0

660

RDSO SPECIFICATION No. M&C/PCN/123/2018 (2018) - SPECIFICATION FOR HIGH PERFORM ANTI-CORROSION EPOXY COATING (TWO PACK)

SPECIFICATION FOR HIGH PERFORM ANTI-CORROSION EPOXY COATING (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found