NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- nthsal-wb@nic.in

Scope List

Reset

1030 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

Specification for LED Based Flasher Light - Specification for LED Based Flasher Light

Specification for LED Based Flasher Light

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Voltage surge test. 1.8 kV as per IEC 61000-4-5)	5000.0
2 (Damp Heat Test as per IEC 60571-2012)	15000.0
3 (Dry heat test as per ELRS/SPEC/LFL/0017 (Rev-I, Sep 2024) Cl no. 6.10.5)	10000.0
4 (Cooling test as per ELRS/SPEC/LFL/0017 (Rev-I, Sep 2024) Cl no. 6.10.7)	10000.0
5 (Water Ingress test, IP 65 of lamp unit as per IS 10322 : Part 1 (2014))	12000.0
6 (Burn in Test as per ELRS/SPEC/LFL/0017 (Rev-I, Sep 2024) Annexure-2)	15000.0

28681 (2024) - Chopped steel Wool Fiber

Chopped steel Wool Fiber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2 (Tap bulk density 50 gms sample /10 min or 250 taps)	1200.0
3 (Specific Gravity)	1200.0
4 (Micro Structure)	3000.0
5 (Chemical Composition (C,Mn,Si, P & S))	2500.0
6 (Appearance)	1200.0
1 (Acetone Extract)	2500.0

IS 2026 : Part 11 (2021) - Power Transformers Part 11 Dry-Type Transformers

Power Transformers Part 11 Dry-Type Transformers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl No 14.2.5 (Applied Voltage Test)	2500.0
14.2.6 (Induced Voltage Withstand Test)	4000.0
14.2.4 (Measurement of No Load Loss & Current)	6000.0
14.2.3 (Measurement of Short Circuit Impedance and Load Loss)	8000.0
14.2.2 (Measurement of Voltage Ratio and Check of phase Displacement)	2000.0
14.2.1 (Measurement of Winding Resistance)	1000.0
14.3.2 (Temperature Rise Test)	40000.0
Cl. 21.2(e) of IS 1180 (Part 1) (Measurement of Insulation resistance)	1500.0

IS 2026 : Part 1 (2011) - Power Transformers: Part 1 General (Second Revision)

Power Transformers: Part 1 General (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1.2(a) (Temp Rise)	7000.0
10.1) c ) (Loss % Impedence)	20000.0
10.1.1(d) (Loss Current)	12800.0
10.1.3(g) (Measurement of Hormonices of the no load current)	10000.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
10.1.1(b) (Measurement of Voltage ratio & voltage vec,tor group test)	3200.0
10.1.1(a) (Measurement of windlng Resistance)	1600.0
10.1.3(d) (Measurement of Zero phase sequence impedance for 3 Phase transformer)	3000.0
10.1.1(e) (Separate source AC voltage withstand test)	4000.0
10.1.3(g) (% Harmonics)	10000.0
10.1.3(j) (Measurement of Insulation Resistance)	2400.0
10.1.1(b) (Voltage ratio & Phase Displacement)	3200.0
10.1.1(a) (Windlng Resistance)	1600.0
10.1.3(d) (Zero Sequence Impedance)	3000.0
10.1.1(e) (AC voltage withstand test)	4000.0
10.1.1(e) (Induced Overvoltage)	6400.0
10.1.1(d) (No Load loss and current)	9600.0
10.1.1 (C) (% impedance and load loss)	12800.0
10.1.2(a) (Temperatur Rise)	20000.0
10.1.3 (f) (Noise Level)	10000.0
17.3.2 (b) of CBIP Pub. No. 317 (Oil Leakage Test (Pressure Test - Type))	10000.0
17.3.1 (a) of CBIP Pub. No. 317 (Pressure Test Routine (Deflection))	8000.0
17.3.2 (a) of CBIP Pub. No. 317 (Vacuum Test - Type (Deflection))	10000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	3000.0
CBIP Publication no. 317 (Polarization Index Test)	2500.0
CBIP Publication no. 317 (Measurement of Unbalance Current)	5000.0

CUSTOM - COPPER ALLOY

COPPER ALLOY

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Copper, percent by mass)	1200.0
2 (Lead, Percent by mass)	1200.0

Portable LED Light Tower with Genset - Portable LED Light Tower with Genset

Portable LED Light Tower with Genset

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A (Dimensions)	5000.0
B (Telescopic Tower Mast Detail (Construction))	5000.0
C (LED Luminaire)	57000.0
D (Driver)	40000.0
E (General Set Up Parameters)	10000.0
F (Photometric Parameters of System)	10000.0
G (Accessories and Packing)	2000.0
H (Genset Details)	35000.0

Custom Mech Gauges dimension - Custom Mechanical Gauges dimension as per drg.

Custom Mechanical Gauges dimension as per drg.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Gauges dimension as per drg.)	3000.0

CUSTOM/COMPOSITE STRAP/2024 - CUSTOM/COMPOSITE STRAP/2024

CUSTOM/COMPOSITE STRAP/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Tensile Strength)	2000.0
2.0 (Elongation)	1000.0
3.0 (System Breaking Strength (Strap + Buckles))	2000.0
4.0 (Width of the Strap)	1000.0
5.0 (Thickness of the Strap)	1000.0
6.0 (Linear Breaking Strength)	2000.0

1264:1997 - Brass Gravity Die Castings

Brass Gravity Die Castings

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Copper)	1200.0
7.1 (Tin)	1200.0
7.1 (Lead)	1200.0
7.1 (Nickel)	1200.0
7.1 (Iron)	1200.0
7.1 (Aluminium)	1200.0
7.1 (Manganese)	1200.0
7.1 (Silicon)	1200.0

IS 17682 (2021) - ALUMINIUM COMPOSITE PANEL

ALUMINIUM COMPOSITE PANEL

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Tensile strength)	1000.0
7.1 (Yield strength)	1000.0
7.1 (% Elongation)	1000.0
7.1 (Density of Core (As per IS 13360 Part-3/Sec 10 or Sec 11))	1000.0
6 (Dimension)	1000.0
7.1 (Coating Thickness on aluminium sheet)	2000.0

IS 17682 (2021) - ALUMINIUM COMPOSITE PANEL SPECIFICATION

ALUMINIUM COMPOSITE PANEL SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

IS 11084 (2023) - Silver Palladium Alloy Wire and Strip for Electrical Contacts

Silver Palladium Alloy Wire and Strip for Electrical Contacts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.4 (Tensile Strength)	2000.0
6.4 (% Elongation)	1000.0
6.4 (Vickers Hardness)	2000.0
6.4 (Reverse Bend Test)	1500.0
6.2 (Freedom from defects)	1000.0

IS 13620 (1993) - Fusion Bonded Epoxy Coated Reinforcing Bars -

Fusion Bonded Epoxy Coated Reinforcing Bars -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A-5 (Pull-out test)	20000.0

Custom - Modified Bitumen

Modified Bitumen

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Softening point)	1200.0
2 (Penetration)	1200.0

15041:2001 (RA 2024) - Textiles – Flat woven webbing slings made of man-made fibres for general services

Textiles – Flat woven webbing slings made of man-made fibres for general services

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.28 (Safe Working Load)	3000.0
3.28 (Safe Working Load)	6000.0
3.28 (Safe Working Load)	8000.0
3.28 (Safe Working Load)	10000.0
5.4 (Proof Load)	3000.0
5.4 (Proof Load)	5000.0
5.4 (Proof Load)	8000.0
5.4 (Proof Load)	10000.0

IS 1838 : Part 3 (2011) - Preformed Fillers for Expansion Joints in Concrete Pavements and Structures(non-extruding and resilient type) Part 3 Polymer Based

Preformed Fillers for Expansion Joints in Concrete Pavements and Structures(non-extruding and resilient type) Part 3 Polymer Based

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.0 (Dimensions)	1000.0
6.0 (Resistance to handling)	1000.0
6.0 (Recovery)	1000.0
6.0 (Compression)	1000.0
6.0 (Extrusion)	1000.0
6.0 (Water Absorption)	1000.0
6.0 (Density)	1000.0
6.0 (Weathering)	5000.0

IS 17875 (2022) - Stainless Steel Seamless Pipes and Tubes for General Services

Stainless Steel Seamless Pipes and Tubes for General Services

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 (Tensile Strength)	1000.0
10.1 (Yield Strength)	1000.0
10.1 (Percent Elongation)	1000.0
23 (Outside Diameter)	500.0
21 (Workmanship, Finish, and Appearance)	1000.0
12 (HARDNESS TEST FOR TUBES)	2000.0
13 (FLARING TEST (FOR TUBES ONLY))	1500.0
23 (Wall Thickness)	500.0
15 (Micro Structure Austenitic Grain Size)	3000.0
17 (Hydraulic Pressure Test)	5000.0
18 (Inter-Granular Corrosion Test)	10000.0
8 (Chemical Composition)	5000.0
8.1 & 8.2 (Carbon) (Carbon (as C))	1000.0
8.1 & 8.2 (Manganese) (Manganese (as Mn))	1000.0
8.1 & 8.2 (Silicon) (Silicon (as Si))	1000.0
8.1 & 8.2 (Nickel) (Nickel (as Ni))	1000.0
8.1 & 8.2 (Chromium) (Chromium (as Cr))	1000.0
8.1 & 8.2 (Molybdenum) (Molybdenum (as Mo))	1000.0
8.1 & 8.2 (Sulphur) (Sulphur (as S))	1000.0
8.1 & 8.2 (Phosphorus) (Phosphorus (as P))	1000.0
8.1 & 8.2 (Copper) (Copper (as Cu))	500.0
8.1 & 8.2 (Nitrogen) (Nitrogen (as N))	500.0
8 (CHEMICAL COMPOSITION, C,Si,Mn,Ni,Cr, Mo, S,P,N,Cu ,Others)	5000.0

IS 17876 (2022) - Stainless Steel Welded Pipes and Tubes for General Services - Specification

Stainless Steel Welded Pipes and Tubes for General Services - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Clauses 8.1 and 8.2 (Carbon (as C))	1000.0
Clauses 8.1 and 8.2 (Silicon (as Si))	1000.0
Clauses 8.1 and 8.2 (Manganese (as Mn))	1000.0
Clauses 8.1 and 8.2 (Nickel (as Ni))	1000.0
Clauses 8.1 and 8.2 (Chromium (as Cr))	1000.0
Clauses 8.1 and 8.2 (Molybdenum (as Mo))	1000.0
Clauses 8.1 and 8.2 (Sulphur (as S))	1000.0
Clauses 8.1 and 8.2 (Phosphorus (as P))	1000.0
10.1 (Tensile Requirement - Tensile Strength as per IS 1608 Part 1 or Test Method specified)	1000.0
10.1 (Tensile Requirement - Yield Strength as per IS 1608 Part 1 or Test Method specified)	1000.0
10.1 (Tensile Requirement - %Percentage of Elongation (on Gauge Length of 50mm) as per IS 1608 Part 1 or Test Method specified)	1000.0
12 (Hardness Test - Rockwell Hardness as per IS 1586 Part 1 / Brinell Hardness as per IS 1500 Part 1 or other Test Method Specified)	2000.0
11 (Transverse Tension Test as per IS 1608 Part 1)	3000.0
13 (Flange Test as per IS 2330 or relevant Test Method Specified)	1500.0
14 (Reverse Flattening Test as per IS 17876 or specified Test Method)	1000.0
16 (Grain Size determined as per IS 4748 or relevant test method specified)	3500.0
18 (Leak Tightness Test by Hydrostatic Test as IS 17876 or relevant test method specified)	2500.0
19 (Corrosion Resistance as per IS 10461 Part 1 or IS 10461 Part2 or relevant test method specified)	10000.0
22 (Workmanship, Finish, and Appearance- Visual Examination as per IS 17876 or relevant Test Method Specified)	1000.0
23 (Repair by Welding or Grinding - Visual Examination as per IS 17876 or relevant Test Method Specified)	1000.0
24 (Dimension Measurement as per IS 17876 or relevant test method Specified)	1000.0
25 (Marking - Visual Examination as per IS 17876)	1000.0
8 (Chemical Composition - Ladle Analysis as per IS 228 and its relevant parts or any other established instrumental/chemical method)	5000.0

Custom/Paint-RPPT/2024 (2024) - Custom/Paint-RPPT/2024

Custom/Paint-RPPT/2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Tensile Strength)	2000.0
2.0 (Elongation)	1000.0
3.0 (Hardness(Shore A))	1000.0
4.0 (Water Absorption)	2000.0
5.0 (Adhesion Test on Concrete)	1200.0
6.0 (Viscosity (Brookfield))	1200.0
7.0 (Dry Film Material Softening Point)	2000.0
8.0 (Specific gravity)	1500.0
9.0 (Solid Content)	1200.0

IS 14252 (2015) - Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Ash Content)	2000.0
4 (Avg. Breaking Strength of fabric after UV exposure)	2000.0
4 (Elongation at break of fabric, Widthwise)	2000.0
4 (Elongation at break of fabric, Lengthwise)	2000.0
4 (Average Breaking Strength of bottom seam)	2000.0
4 (Avg. Breaking Strength of fabric, Widthwise)	2000.0
4 (Avg. Breaking Strength of fabric, Lengthwise)	2000.0
4 (Mass of Sack (without tying cord))	2000.0
4 (Picks/dm)	2000.0
4 (Ends/dm)	2000.0
4 (Dimensions, Outside Width)	2000.0
4 (Dimensions, Outside Length)	2000.0
4 (Mass of Bale)	2000.0
3.4.1 (Mouth of Sack, Channel secured with )	2000.0
3.4.1 (Mouth of Sack, Channel withturn-in)	2000.0
3.3 (Tying cord Material Identification)	2000.0
3.4.1 (Mouth of Sack, Channel width)	2000.0
3.4.1 (Bottom Seam, Number of Stitchs per dm)	2000.0
3.4.1 (Bottom Seam, Double fold seam depth)	2000.0
3.4.1 (Bottom Seam, Outer stitch distance from outer edge)	2000.0
3.4.1 (Bottom Seam, Two row separation distance)	2000.0
4 (UV - Resistance Test (192 hrs.))	9600.0
4 (GSM of Fabrics)	1000.0

IS 3181 (1992) - Conveyor belts - Fire resistant conveyor belting for underground mines and such other hazardous applications - Specification (Second Revision)

Conveyor belts - Fire resistant conveyor belting for underground mines and such other hazardous applications - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.0 (Belt Thickness)	1000.0
7.0 (Carcass Thickness)	1000.0
8.0 (Cover Thickness)	1000.0
11.0 (Full Thickness Breaking Strength)	5000.0
11.0 (Full Thickness Elongation at Break)	1000.0
11.2 (Elongation at Reference Load)	1000.0
12.0 (Tear Strength)	2000.0
13.0 (Adhesion between Cover and Carcass)	2000.0
13.0 (Adhesion between Adjacent Plies)	2000.0

276 - Austentic Manganese Steel Castings specification

Austentic Manganese Steel Castings specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Carbon)	1200.0
8.1 (Silicon)	1200.0
8.1 (Manganese)	1200.0
8.1 (Phosphorus)	1200.0
8.1 (Sulphur)	1200.0
8.1 (Chromium)	1200.0
8.1 (Molybdenum)	1200.0
8.1 (Nickel)	1200.0

Calibration of Cold Chamber - Calibration of Cold Chamber

Calibration of Cold Chamber

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Calibration of cold Chamber -40 deg C to Ambient)	10000.0
A2 (Calibration of cold Chamber -80 deg C to Ambient)	15000.0

Custom - Microsilica

Microsilica

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Silica as SiO2)	1200.0
2 (Soda as Na2O)	1200.0
3 (Moisture)	1200.0
4 (Loss on Ignition)	1200.0

Custom - White Lithium Grease

White Lithium Grease

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drop Point)	1200.0
2 (Specific Gravity)	1200.0

CUSTOM - Aluminium content (% by mass)

Aluminium content (% by mass)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Aluminium Content (% by mass))	2000.0

Training at Electrical Laboratory, NTH(ER), Salt Lake - Training at Electrical Laboratory, NTH(ER), Salt Lake

Training at Electrical Laboratory, NTH(ER), Salt Lake

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
A1 (Training for 5 days)	1500.0
A2 (Training for 10 days)	3000.0
A3 (Training for 15 days)	4500.0

Customized specification China Clay (2024) - Customized specification China Clay

Customized specification China Clay

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Silica(As SiO2),% by mass)	2000.0
2 (Aluminum oxide(as Al2O3),% By mass)	1200.0
3 (Titanium dioxide (TiO2),% by mass)	2500.0
4 (Brightness %)	1200.0

8419 (1977) - Requirement of Filtration Equipment (Part 1) Filtration Media - Sand and Gravels

Requirement of Filtration Equipment (Part 1) Filtration Media - Sand and Gravels

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.1 (Effective Size (Particle diameter corresponding to 10% fines) [IS 2720 Part IV])	3000.0
2.2 (Uniformity Coefficient (The ratio D60/D10 Particle diameter corresponding to 60% and 10% fines) [IS 2720 Part IV])	3000.0
3.1.1 (Specific Gravity [IS 2386 (Part 3)])	1000.0
3.1.1 (Silica Content [IS 2000], %)	3000.0

CUSTOM (2024) - RDSO PAINT 2024

RDSO PAINT 2024

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (AMINE VALUE TEST (as per annexure III of MDTS 48279 Rev 4))	1.0

First
Prev
1
2
3
4
Next
Last