NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum[at]nth[dot]gov[dot]in

Scope List

Reset

924 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

661

2933 (Part 1) (2013) - Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications

Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Lead Restriction, (IS 101 (Part 8/Sec 5))	700.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (a) Consistency, (Annex C))	1000.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (b) Viscosity by ford cup No. 4 at (27 +/- 2 deg C), (IS 101 (Part 1/Sec 5)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Mass, kg/10 litre, Min, (IS 101 (Part 1/Sec 7)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Drying time, h, Max : a) Surface dry (IS 101 (Part 3/Sec 1)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Drying time, h, Max : b) Hard dry (IS 101 (Part 3/Sec 1)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Drying time, h, Max : c) Tack free (IS 101 (Part 3/Sec 1)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Wet opacity, Min, (IS 101 (Part 4/Sec 1)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Finish, (IS 101 (Part 3/Sec 4)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Fineness of grind, Max (IS 101 (Part 3/Sec 5)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Colour, (IS 101 (Part 4/Sec 2)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Water content (if water is suspected to be present), Max, (IS 101 (Part 2/Sec 1)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Flexibility and adhesion: a) Scratch hardness, (Load 1000 g), clause 3 of (IS 101 (Part 5/Sec 2)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Flexibility and adhesion: b) Bend test, (with 6.25 mm Dia Mandrel in type 1 apparatus), clause 2 of (IS 101 (Part 5/Sec 2)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Striping test (Annex D))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Flash Point, (IS 101 (Part 1/Sec 6)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Keeping properties , (IS 101 (Part 6/Sec 2)))	5000.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Durability: Accelerated Weathering test (Xenon arc ) (clause no. 6.2 of IS 2933 (Part 1)))	21600.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Durability: Normal Outdoor Exposure test for 12 Months (Annex B-3))	10000.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Total non-volatile matter, (IS 101 (Part 8/Sec 2)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Total pigment content)	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Phthalic anhydride content of the non-volatile vehicle, (IS 101 (Part 8/Sec 4)))	500.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Please refer annexure)	1.0
Enamel, Exterior: (a) Undercoating (b) Finishing - Specification Part 1 for Domestic and Decorative Applications (Gloss (specular 60 deg), (IS 101 (Part 4/Sec 4)))	500.0

662

IS 14333 - High Density Polyethylene Pipe For Sewerage -

High Density Polyethylene Pipe For Sewerage -

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.4 (Melt Flow Rate (IS:14333 & IS:2530))	2000.0
8.2 (Reversion Test (IS:14333 & IS:4984))	1000.0
7.4 (Outside Diameter (IS:14333 & IS:4984))	500.0
7.4 (Wall Thickness (IS:14333 & IS:4984))	500.0
8.5 (Carbon Black Content and Dispersion)	2000.0
8.6 (Density (IS:14333 & IS:7328))	2000.0

663

ASTM D 412 - Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers/Tension

Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers/Tension

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength)	2000.0
- (Elongation (Both directions))	2000.0

664

IS 1848 : Part 2 (2018) - Writing and printing papers - Specification: Part 2 air mail/manifold, cartridge drawing and cartridge white, duplicating absorbent and duplicating semi - Absorbent and poster machine glazed types (Fifth Revision)

Writing and printing papers - Specification: Part 2 air mail/manifold, cartridge drawing and cartridge white, duplicating absorbent and duplicating semi - Absorbent and poster machine glazed types (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Substance (Grammage),)	1000.0

665

IS 1528 (2010) - Refractory materials

Refractory materials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Part 4 (Cold Crushing Strength (as per IS 1528 (Part 4): 2012), in N/mm^2)	2500.0
Part 8 / Part 15 (Apparent Porosity [on the lines of IS 1528 (Part 8)/ IS 1528 (Part 15)], %)	1000.0

666

ASTM D 257 (1999) - Solid insulating materials

Solid insulating materials

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Solid insulating materials)	1000.0

667

ISO / EN / ASTM - Custom Specn Adhesive / Coating NTH(WR)

Custom Specn Adhesive / Coating NTH(WR)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Pull out test of coating, (ISO 4624), N/mm^2)	5000.0
8 (Pull-off Adhesion Strength of Coating on Concrete (on the lines of ASTM D 7234-12), MPa)	5000.0
8 (Average Tensile Strength (on the lines of ASTM D 412), N/mm^2)	2000.0
8 (Average Elongation at Break (on the lines of ASTM D 412), in %)	2000.0
5 (Depth of Permeability of Water under pressure (on lines of BS EN 12390), in mm)	10000.0
5 (Depth of Permeability of Water under pressure-comparison with controlled specimen (on lines of BS EN 12390), in mm)	15000.0

668

MORTH : Part 5 (2013) - SPECIFICATIONS FOR ROAD AND BRIDGE WORKS/ASTM

SPECIFICATIONS FOR ROAD AND BRIDGE WORKS/ASTM

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
505 (Thickness of Dense Bituminous Macadam (DBM), in mm)	1000.0
507 (Thickness of Bituminous Concrete Layer (BC), in mm)	1000.0
505 (Combined Density of Dense Bituminous Macadam (DBM) & BC, in g/cc)	2000.0
505 (Binder Content of DBM, in %)	3000.0
507 (Bitumen Content of BC, in %)	3000.0
507 (Thickness of DBM Layer (BC), in mm)	1000.0
505 (Density DBM (ASTM-D2726))	2000.0
507 (Density of BC (ASTM-D2726))	2000.0
Binder Content of SDAC (Binder content of Semi Dense Asphaltic Concrete)	3000.0
Binder Content DAC (Binder content of Dense Asphaltic Concrete)	3000.0
505 (Binder Content of DBM, in %)	3000.0
Density of SDAC (Density of Semi Dense Asphaltic Concrete)	2000.0
Density DAC (Density of Dense Asphaltic Concrete.)	2000.0
CLAUSE-1,Table-1 (Cutting & Preparation of Core sample-Single Stage)	1000.0

669

Cust Specn Adhesive - Custom Specification for Adhesive NTH(WR)

Custom Specification for Adhesive NTH(WR)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ASTM (Accelerated Weathering Test by Xenon Arc (500 hr))	30000.0
IS 15477 (Modified Adhesion Test before exposure to Accelerated Weathering Test, N)	8000.0
IS 15477 (Modified Adhesion Test after exposure to Accelerated Weathering Test, N)	8000.0
ASTM (Accelerated Weathering Test by Xenon Arc (250 hr))	15000.0
ASTM D 4541 / 7234 (Pull off Adhesion Strength of coating (a) Control sample (b) Coated Sample.)	10000.0

670

RDSO SPECIFICATION No. M&C/PCN/123/2018 (2018) - SPECIFICATION FOR HIGH PERFORM ANTI-CORROSION EPOXY COATING (TWO PACK)

SPECIFICATION FOR HIGH PERFORM ANTI-CORROSION EPOXY COATING (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Weight per epoxy equivalent on non-volatile vehicle content basis (Cl.4 of IS:9162-1979))	3500.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Drying time at (27+/-2 deg C) a) Surface dry (IS: 101 (Pt. 3/Sec.1)-1986)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Drying time at (27+/-2 deg C) b) Recoating time (IS: 101 (Pt. 3/Sec.1)-1986)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Drying time at (27+/-2 deg C) c) Hard dry (IS: 101 (Pt. 3/Sec.1)-1986)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Drying time at 27(+/-2 deg C) d) Curing time (IS: 101 (Pt. 3/Sec.1)-1986)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Consistency (IS: 101 (Pt. 1/Sec. 5)-1989)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Finish (IS: 101 (Pt. 3/Sec. 4)-1987)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Colour (IS: 101 (Pt. 4/Sec. 2)-1989)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Dry film thickness per coat, by brush/air/airless spray (IS: 101 (Pt.3/Sec.2)-1989 By Elecometer Thickness gauge meter)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Volume solids, Appendix-I of RDSO SPECIFICATION No.M&C/PCN/123/2018)	2000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Scratch hardness (at 1.5 Kg load) (IS: 101 Pt.5/Sec.2)-1988)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Flexibility & Adhesion (6.25 mm Mandrel) (IS: 101 Pt.5/Sec.2)-1988)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Flash point for both the packs (IS: 101 (Pt.1/Sec. 6)-1987)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Resistance to salt spray for 3000 hours (ASTM: B-117))	100000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Protection against corrosion under condition of condensation for 3000 hours (IS: 101 (Pt. 6/Sec.1)-1988)	75000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Keeping properties for both the packs (IS : 101 (Pt. 6/Sec.2)-1989)	5000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Covering Capacity, min i) 100 micron DFT (IS: 101 (Pt.4/Sec.1)-1988)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Covering Capacity, min ii) 75 micron DFT (IS: 101 (Pt.4/Sec.1)-1988)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Resistance to chemicals i) 25% caustic soda solution (w/v) for 1800 hrs, Appendix-II of RDSO SPECIFICATION No.M&C/PCN/123/2018)	3000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Resistance to chemicals ii) 30% sulphuric acid solution (v/v) for 1800 hrs, Appendix-II of RDSO SPECIFICATION No.M&C/PCN/123/2018)	3000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Resistance to chemicals iii) 20% hydrochloric acid solution (v/v) for 1800 hrs, Appendix-II of RDSO SPECIFICATION No.M&C/PCN/123/2018)	3000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Resistance to chemicals iv) Resistance to tap Water for 3000 hrs, Appendix-II of RDSO SPECIFICATION No.M&C/PCN/123/2018)	2000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Pot life at 27(+/-2) deg C, min. Appendix-III of RDSO SPECIFICATION No.M&C/PCN/123/2018)	1500.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Mass in kg/10 litres, min, (IS : 101 (Pt. 1/Sec.7)-1987)	1200.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Impact resistance test at height 31 inch and weight 3.226 pound) (100 inch pound load), (ASTM D 2794))	1500.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Cathodic disbondment test, max)	10000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Abrasion Resistance test for 1000 cycles with CS-17 wheels & 1.0 Kg load (ASTM D 4060))	3000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Adhesion test (ASTM D 3359))	1500.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Adhesion & Compatibility test with Acrylic Polyurethane Paint (ASTM D 3359 & Appendix -IV))	2000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Pull of Adhesion test, Min (ASTM D 4541))	2000.0
RDSO SPECIFICATION No.M&C/PCN/123/2018 (Please refer annexure for test result as per RDSO SPECIFICATION No.M&C/PCN/123/2018)	1.0

671

RDSO SPEC M&C/PCN/103/2020 (2020) - SPECIFICATION FOR EPOXY BASED MICACEOUS IRON OXIDE (TWO- PACK)

SPECIFICATION FOR EPOXY BASED MICACEOUS IRON OXIDE (TWO- PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

672

266 (1993 (RA2020)) - Sulphuric Acid

Sulphuric Acid

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 and 4.3 (i) (Total Acidity (as H2SO4))	1000.0
4.2 and 4.3 (ii) (Residue on Ignition)	500.0
4.2 and 4.3 (iii) (Iron (as Fe))	500.0
4.2 and 4.3 (iv) (Chlorides (as Cl))	500.0
4.2 and 4.3 (v) (Lead (as Pb))	1.0
4.2 and 4.3 (vi) (Arsenic (as As))	500.0
4.2 and 4.3 (vii) (Oxidizable Impurities (as SO2))	500.0
4.2 and 4.3 (viii) (Organic Matter)	500.0
4.2 and 4.3 (ix) (Nitrates (as NO2))	500.0
4.2 and 4.3 (x) (Ammonia (as NH3))	500.0
4.2 and 4.3 (xi) (Selenium (as Se))	500.0
4.2 and 4.3 (xii) (Manganese (as Mn))	500.0
4.2 and 4.3 (xiii) (Copper (as Cu))	500.0
4.2 and4.3 (xiv) (Zinc (as Zn))	500.0
4.2 and 4.3 (xv) (Nitrates, Nitrites, and Ammonia (as N))	500.0
4.1.3 (Preliminary Examination)	500.0
Specific Gravity (Specific Gravity)	500.0
TEST RESULTS AS PER ANNEXURE (TEST RESULTS AS PER ANNEXURE)	5000.0

673

Customized specification for Polycarbonate seal - Customized specification for Polycarbonate seal

Customized specification for Polycarbonate seal

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Breaking Strength ( On the lines of ASTM D 638 )-Breaking load between wire and seal in tension)	3000.0
- (Corrosive Resistance Test(On the lines of ASTM D 543-14))	2000.0
- (Heat Resistance Test(On the lines of ASTM D 3045-92))	2000.0

674

IS 10322 : Part 1 (2014) - Luminaires: Part 1 general requirements and tests (First Revision)

Luminaires: Part 1 general requirements and tests (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 ()	-

675

IS 374 (2019) - Specification for electric ceiling type fans and regulators (Third Revision)

Specification for electric ceiling type fans and regulators (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1,e (Input in watts)	10.0
14.5 (Power factor)	500.0
14.4 (Fan speed (RPM), %)	100.0

676

Customer Specification - Electrical product

Electrical product

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Tests)	75000.0
1 (As per Customer request)	20000.0
1 (As per customer requirement)	40000.0
5 (Tests as per Customer request)	45000.0
6 (Tests as per Customer request 2)	30000.0

677

ONGC Specification for protective coating (2005) - ONGC Offshore Design Section: Specification for protective coating

ONGC Offshore Design Section: Specification for protective coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
ONGC Specification for protective coating (Touch Dry at 25 deg C (ASTM D 1640))	1200.0
ONGC Specification for protective coating (Hard Dry at 25 Deg C (ASTM D 1640))	1200.0
ONGC Specification for protective coating (Over Coating Interval (ASTM D 1640))	1200.0
ONGC Specification for protective coating (Pot Life at 25 Deg C)	1500.0
ONGC Specification for protective coating (Dry Film Thickness, per coat)	1200.0
ONGC Specification for protective coating (Volume Solid (ISO 3233))	2000.0
ONGC Specification for protective coating (Theoretical Covering Capacity)	1200.0
ONGC Specification for protective coating (Weight Per liter (ISO 2811))	1200.0
ONGC Specification for protective coating (Temperature Resistance (ASTM D 2485 Method A))	5000.0

678

Civil lab Training - Evaluation of Building Materials through Quality Testing & Standard specification-Training

Evaluation of Building Materials through Quality Testing & Standard specification-Training

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Training)	5000.0

679

IS 2046 (1995) - Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

Decorative Thermosetting Synthetic Resin Bonded Laminated Sheets

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.1 (Colour and pattern)	500.0
5.2.1 (Surface Finish)	500.0
5.3 (Thickness)	1000.0
5.4.1 (Surface Defects)	1000.0
5.5 (Resistance to suface wear)	3000.0
5.5 (Resistance to immersion in Boiling water(mass increase))	1000.0
5.5 (Resistance to immersion in Boiling water(thickness increase))	1000.0
5.5 (Resistance to immersion in boiling water (Appearance))	500.0
5.5.3 (Resistance to Dry Heat at 180 degC.)	2000.0
5.5 (Dimensional Stability at Elevated Temperature (L))	1500.0
5.5 (Dimensional Stability at Elevated Temperature(T))	1500.0
5.5 (Dimensional Stability at 20 degC(L))	1000.0
5.5 (Dimentional Stability at 20 degC(T))	1000.0
5.5 (Resistance to Cracking)	2000.0
5.5 (Resistance to Scratching)	2000.0
5.5 (Resistance to Staining)	5000.0
5.5 (Resistance to colour change in Xenon arc light)	3000.0
5.5 (Resistance to Cigarate Burns)	2000.0
5.5 (Resistance to Steam)	2000.0
- (Density)	1000.0
5.5 (Tensile strength)	2000.0
5.5 (Flexural Strength)	2000.0
5.5 (Resistance to crazing)	1500.0
5.5 (Resistance to surface wear)	5000.0

680

IS 266 (1993) - Sulphuric acid - Specification (Third Revision)

Sulphuric acid - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.2 (Total Acidity (as H2SO4))	1000.0
4.2 (Residue on ignition)	1000.0
4.2 (Iron (as Fe))	1000.0
4.2 (Chlorides (as Cl))	1000.0
4.2 (Lead (as Pb))	1000.0
4.2 (Arsenic (as As))	1000.0
4.2 (Oxidizable impurities (as SO2))	1000.0
4.2 (Organic matter)	1000.0
4.2 (Nitrates (as NO3))	1000.0
4.2 (Ammonia (as NH3))	1000.0
4.2 (Selenium (as Se))	1000.0
4.2 (Manganese (as Mn))	1000.0
4.2 (Copper (as Cu))	1000.0
4.2 (Zinc (as Zn))	1000.0
4.2 (Nitrates, nitrites & ammonia (as N))	1000.0

681

IS 2046-IS 2046 (1995) - Decorative thermosetting synthetic resinbonded laminated sheets specification (Second Revision)

Decorative thermosetting synthetic resinbonded laminated sheets specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

682

NTH(WR)/MECH/CUSTOM/004 (2022) - Customer Specification- Dimension Measurement of Weight Per Litre Cup

Customer Specification- Dimension Measurement of Weight Per Litre Cup

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Dimension Measurement of Weight Per Litre Cup)	2000.0
2 (Dimension Measurement of Weight Per Litre Cup)	4000.0

683

EN / BS/ IS - Method of test of Rock

Method of test of Rock

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 of EN 13383 (Part 2) (Determination of Particle Density (EN 13383-2:2013), Mg/m^3)	1500.0
8 of EN 13383 (Part 2) (Determination of Water Absorption (EN 13383-2:2013), %)	1500.0
8 of EN 1926 :2006 (Compressive strength (EN 1926 : 2006), MPa)	5000.0
8 of EN 1926 :2006 (Compressive strength normal to plane of anisotropy (EN 1926 : 2006), MPa)	5000.0
8 of EN 1926 :2006 (Compressive strength Parallel to plane of anisotropy (EN 1926 : 2006), MPa)	5000.0
5 of BS EN 1097 - 2 : 2010 (Determination of resistance to fragmentation by Los Angeles Test Method (BS EN 1097-2 : 2010), %)	2000.0
9 of BS EN 1367-2 : 2009 (Magnesium Sulphate Test (BS EN 1367 - 2 : 2009), MS Value in %)	4000.0
3 (Average Loose Bulk Density,)	500.0
3 (Average Compacted Bulk Density)	500.0
2 (Water Absorption)	1000.0
2 (Specific Gravity)	1000.0
6 (Soundness [Magnesium Sulphate Solution])	4000.0
5.3 (Aggregate Abrasion Value (Los Angeles Abrasion))	2000.0
4 (Compressive Strength of Rock Core)	5000.0

684

JIS K 6911 and Customer requirements - Sheet Molding Compound

Sheet Molding Compound

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Flexural Strength (JIS K 6911:1995))	4000.0
- (Water absorption test (JIS K 6911:1995))	2000.0
- (Appearance after boiling (JIS K 6911:1995))	2000.0
- (Specific Gravity (IS 8543(Part 1/Sec 2):1979))	1000.0
- (Withstand voltage flatwise (JIS K 6911:1995))	2000.0
- (Insulation resistance test at normal state and after boiling (JIS K 6911:1995))	3000.0

685

IS 1554 : Part 1 (1988) - SPECIFICATION FOR PVC INSULATED ( HEAVY DUTY ) ELECTRIC CABLES

SPECIFICATION FOR PVC INSULATED ( HEAVY DUTY ) ELECTRIC CABLES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
15.1 (Type Tests)	75000.0
15.1 (Type Test)	40000.0
15 (Type tests (Non FRLS))	25000.0

686

IS 2720 / 2386 (1983) - Method of Test of Soils (Blanketing Material / Earth / Fill Material)

Method of Test of Soils (Blanketing Material / Earth / Fill Material)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Part 8, Cl 5 & 6 (Determination of Water Content- Dry Density Relation using Heavy Compaction [IS 2720(Part 8)].)	5000.0
Part 16, Cl. 5.2 (Laboratory Determination of CBR [IS 2720 (Part 16)],)	6000.0
Part 4 (Grain Size Analysis [IS 2720 (Part 4)],)	5000.0
Part 4, cl. No. 5 (Coefficient of Uniformity from Grain size analysis, Cu)	500.0
Part 4, cl. No. 5 (Coefficient of curvature from grain size distribution, Cc)	500.0
Part 5, (Atterberg Limit (Liquid Limit, Plastic Limit and Plasticity index), IS 2720 (Part 5).)	3000.0
IS 2386 (Part 1), (Combined Flakiness Index and Elongation Index, [IS 2386 (Part 1)])	3000.0
IS 2386 (Part 5), (Soundness of aggregate [IS 2386 (Part 5)])	2000.0
- - (Classification of soil)	2000.0
4 (Aggregate Impact Value)	2000.0
2 (Water Absorption)	1000.0
- - (Total Sulphate Content)	1000.0
- - (Total Chloride Content)	1000.0
- - (Organic Matter)	1000.0
- - (Carbonate content)	1000.0

687

IRS-GE-1 (2016) - Specifications for Track ballast (IRS-GE-1)

Specifications for Track ballast (IRS-GE-1)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.2.1 (Aggregate abrasion Value (IS 2386(IV):1963))	2500.0
2.2.2 (Aggregate Impact Value (IS 2386(Part IV):1963))	2500.0
2.2.3 (Water absorption ( IS 2386 (III):1963))	1000.0
2.3 (Size and Gradation (as per annexure IV of IRS-GE-1,June 2016))	2000.0
1 (Flakiness index (as per IS 2386 (Part 1) : 1963), %)	2000.0
1 (Elongation index (as per IS 2386 (Part 1) : 1963), %)	2000.0

688

GE: IRS -2 (Final) (2005) - SPECIFICATION FOR MECHANICALLY PRODUCED BLANKETING MATERIAL FOR RAILWAY FORMATIONS INCLUDING GUIDELINES FOR LAYING

SPECIFICATION FOR MECHANICALLY PRODUCED BLANKETING MATERIAL FOR RAILWAY FORMATIONS INCLUDING GUIDELINES FOR LAYING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (DETERMINATION OF WATER CONTENT-DRY DENSITY RELATION (IS 2720(8):1983) (Proctor test))	5000.0
4.1.C.1 (Test for Non Plastic fines(Particles of size less than 75 micron)(as per GE: IRS -2 (Final)))	1000.0
4.1.C.2 (Test for Plastic fines(GE: IRS -2 (Final)))	1000.0
4.1.d (Test for Particle size distribution(GE: IRS -2 (Final)))	5000.0
4.1.e.1 (Test for Uniformity Co-efficient (Cu) {GE: IRS -2 (Final)})	1500.0
4.1.e.2 (Test for Co-efficient of Curvature(CC) (GE: IRS -2 (Final)))	1500.0
- (Test for Aggregate Abrasion Value (Los Angeles) as per IS 2386 (Part 4): 1963)	1500.0
IS 2720 (Part 16) (California Bearing Ratio (in dry condition))	7000.0
IS 2720 (Part 16) (California Bearing Ratio (in soaked condition))	7000.0

689

IS 1161 (2014) - Steel tubes for structural purposes - Specification (Fifth Revision)

Steel tubes for structural purposes - Specification (Fifth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8 (Coating thickness, micron)	2000.0
5 (Chemical Composition)	2500.0
11.3.2 (Flattening Test above 50 mm NB)	1000.0
11.3.1 (Cold Bend Test up to 50 mm NB)	1000.0
11.2 (Percentage Elongation, %)	1000.0
11.2 (Yield Strength, MPa)	1000.0
11.2 (Tensile Strength, MPa)	1000.0
6 (Dimension)	1000.0
6 (Mass per meter, kg/m)	1000.0
7 (Workmanship)	1000.0
0 (Adhesion Test)	1000.0
0 (Salt Spray Test)	60000.0
0 (Mass of Zinc Coating)	2000.0

690

IS 1269:Part 2 (1997) - Legal metrology - Material Measures of Length, Part 2: Steel Tape Measures

Legal metrology - Material Measures of Length, Part 2: Steel Tape Measures

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found