NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum[at]nth[dot]gov[dot]in

Scope List

Reset

805 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

481

IS 2720 - Methods of Tests for Soils

Methods of Tests for Soils

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Grain size analysis- (IS 2720(Part 4):1985)	5000.0
2 (Determination of Liquid limit-(IS 2720(Part 5):1985))	1000.0
3 (Determination of Plastic Limit(IS 2720(Part 5):1985))	1000.0
4 (Determination of Plasticity Index-(IS 2720(Part 5):1985))	500.0
5 (Determination of Water Content-Dry density relation using light compaction (IS 2720(Part 7):1980))	5000.0
6 (Determination of Water Content-Dry density relation using heavy compaction (IS 2720(Part 8):1983))	5000.0
7 (Laboratory determination of CBR (IS 2720(Part 16):1987))	4000.0
10 (Determination of Shrinkage limit (IS 2720(6)1972))	1000.0
- (Type of Soil-Classification & Identification of Soil (IS 1498:1970))	2000.0
- (Moisture content (IS:2720(Part 2):1973))	1000.0
- (Organic matter- (IS 2720(22):1972))	1200.0
- (pH)	1000.0
- (Total Soluble sulphates)	2000.0
- (Free swell index (Methods of test for soils: IS 2720 (Part 40) : 1977 Reviewed In : 2021))	1000.0
8 (Determination of Uniformity coefficient(Cu): (IS 1498:1970))	1500.0
9 (Determination of Coefficient of Curvature(Cc): (IS 1498:1970))	1500.0

482

15337 (2003) - Coal tar based anticorrosion tape for protection of underground mild steel pipelines - Specification

Coal tar based anticorrosion tape for protection of underground mild steel pipelines - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 4 (clause 4.5) (Solubility of Coal tar based tape in petrol (Annexure C of IS 15337 : 2003))	2000.0

483

Customized test on the lines of IS 636:2018 - Non percolating flexible fire fighting delivery hose

Non percolating flexible fire fighting delivery hose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Heat resistance test as per clause 6.14(Annexure E) (Requirement: None of the test samples shall burst at less than 20s of the application of the hot cube for Type 3 hose))	5000.0

484

IS 2967 (1983 RA 2019) - Specification for external micrometer (First Revision)

Specification for external micrometer (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Deviations and Tolerances)	1200.0
4 (Error of Measurement)	1200.0
4 (Deviations and Tolerances (For 0-100mm))	1500.0
4 (Deviations and Tolerances (above 300mm))	2500.0
4 (Error of Measurement (For 0-100mm))	1200.0
4 (Error of Measurement (For 200-300mm))	2000.0
4 (Error of Measurement)	1200.0

485

NSS-WR-Zinc in Dry Coating - Custom-Percent of Zinc Coating in Dry Coating

Custom-Percent of Zinc Coating in Dry Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Percent of Zinc Content in Dry Film)	2000.0

486

DKD-R 6-1 (2014) - Calibration of Pressure Gauges

Calibration of Pressure Gauges

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Pressure)	3000.0

487

Customized Specification for 3D printed specimen - Customized Specification for 3D printed specimen

Customized Specification for 3D printed specimen

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength (As per ASTM D 638))	4000.0
- (Flexural Strength (As per ASTM D 790))	4000.0
- (Izod Impact resistance(As per ASTM D 256))	4000.0
- (Shore Hardness/Durometer hardness (As per ASTM D 2240))	1000.0

488

Manufacture/Customer Specification - Test as per Manufacturer/Customer Specification

Test as per Manufacturer/Customer Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test as per Manufacture / Customer Specification)	25000.0
17 (LSZH Property)	20000.0

489

RDSO SPECIFICATION No. M&C/PCN/129/2018 (2018) - SPECIFICATION FOR EPOXY BASED ZINC RICH PRIMER (TWO PACK)

SPECIFICATION FOR EPOXY BASED ZINC RICH PRIMER (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Weight per epoxy equivalent on non-volatile vehicle content basis, (CL. 4 of IS 9162-79))	3000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, h, Max : a) Surface dry (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, Max b) Hard dry (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, Max C) Hard dry at 70 Deg C (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Consistency (IS 101 (Part 1/Sec 5)-89)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Finish (IS 101 (Part 3/Sec 4)))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Colour (IS 101 (Part 4/Sec 2)))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Dry Film Thickness per coat, min. a) By Brush (IS 101 (Part 3/Sec 2)-89 By Elecometer)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Volume Solid % min (Appendix-I))	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Scratch hardness, (Load 1000 g), clause 3 of (IS 101 (Part 5/Sec 2))-88)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flexibility and adhesion (6.25mm mandrel), (IS 101 (Part 5/Sec 2))-88)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flash Point (a) Component A (IS 101 (Part 1/Sec 6)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flash Point, (b) Component B (IS 101 (Part 1/Sec 6)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Resistance to salt spray, for 1000 hrs (IS 101 (Part 6/Sec 1)-88)	40000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Protection against corrosion under condition of condensation, for 1000 hrs (IS 101 (Part 6/Sec 1)-88)	30000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Keeping Properties for Pack A, 18 Months (IS 101 (Part 6/Sec 2)-89)	7000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Keeping Properties for Pack B, 18 Months (IS 101 (Part 6/Sec 2)-89)	7000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Mass in kg/10 liters, minimum (IS 101 (Part 1/Sec. 7)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Pot life a) at 27 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Pot life b) at 40 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Theoretical Spreading Capacity, min (with 10% Thinner), Appendix-I)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Fineness of grind, min (IS 101 (Part 3/Sec. 5)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Viscosity (Efflux time by ford cup No. 4 of paint i.e. mixture of two components at 27(+/-2 deg C) (with 10% Thinner))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Please Refer Annexure)	1.0
- (Resistance to Pull of adhesion test, (ASTM D 4541))	2000.0
- (Abrasion resistance test, 1.0 Kg Load, CS-17 Wheel, 1000 cycle (ASTM D 4060))	3000.0

490

RDSO SPECIFICATION No. M&C/PCN/129/2018 (2018) - SPECIFICATION FOR FULL GLOSS POLYSILOXANE BASED ENAMEL (TWO PACK)

SPECIFICATION FOR FULL GLOSS POLYSILOXANE BASED ENAMEL (TWO PACK)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, h, Max : a) Surface dry (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, Max b) Hard dry (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Drying time, Max C) Hard dry at 70 Deg C (IS 101 (Part 3/Sec 1))-86)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Consistency (IS 101 (Part 1/Sec 5))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Colour (IS 101 (Part 4/Sec 2)))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Dry Film Thickness per coat, minimum (IS 101 (Part 3/Sec 2)-89 By Elcometer)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Volume Solid % min (Appendix-I))	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Scratch hardness, (Load 1.5 kg), clause 3 of (IS 101 (Part 5/Sec 2))-88)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flexibility and Adhesion (6.25 mm mandrel), (IS 101 (Part 5/Sec 2))-88)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flash Point a) Component A (IS 101 (Part 1/Sec 6)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Flash Point Component B (IS 101 (Part 1/Sec 6)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Fineness of grind, Max (IS 101 (Part 3/Sec. 5)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Pot life a) at 27 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Pot life a) at 40 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Gloss value at 60 Deg angle of incidence, Minimum (IS 101 (Part 4/Sec 4)-88))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Mass in kg/10 liters, minimum (IS 101 (Part 1/Sec. 7)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Keeping Properties, 18 Months (Appendix-III))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Theoretical Spreading rate, min, Appendix-I)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Viscosity (Efflux time by Ford cup No.4) of paint i.e. mix. Of two components at 27 (+/-2 Deg.C.) in supply condition (IS 101 (Part 1/Sec.5)))	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests a) Resistance to 30% Sulphuric acid (wt by vol) for 24 hours (Appendix-V))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests b) Resistance to 20% caustic potash (wt by vol) for 24 hours (Appendix-V))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests c) Resistance to oil for 2 hours (Appendix-V))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests d) Resistance to Solvent for 3 hours (Appendix-V))	1500.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Accelerated Tests e) Resistance to Water for 240 hours (Appendix-V))	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Durability Tests Accelerated Weathering test, for 1000 hours (Weather-o-meter, Xenon Arc Lamp) (Appendix-VI))	60000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Humidity Tests (on full system) for 4000 hrs (IS 101 (Part 6/Sec 1))	120000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (% Silicone on non-volatile binder basis, (min) (ASTM D 297 & Appendix-VIII)	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Abrasion resistance test with 1.0 kg load & CS-17 Wheels, 1000 cycles, (ASTM D 4060))	3000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Adhesion & Compatibility test on full system (ASTM D 3359 & Appendix-VII))	2000.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Please refer annexure)	1.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Finish (IS 101 (Part 3/Sec 4) -1987))	1200.0
Appendix-VI Durability test (Durability tests Accelerated weathering test, 750 hrs (ASTM G 53, 4 hrs UV and 4 hrs condensation))	45000.0

491

RDSO SPECIFICATION No. M&C/PCN/129/2018 (2018) - Specification for Epoxy Based Micaceous Iron Oxide (Two-Pack) (Chapter-IV)

Specification for Epoxy Based Micaceous Iron Oxide (Two-Pack) (Chapter-IV)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.4 (Weight per Epoxy Equivalent on Non-volatile vehicle content basis (IS 9162-79))	3500.0
3.5a (Pigment content (3.5a) (IS 101 (Part 8/Sec. 2)-90)	2000.0
Table No. II (Drying time, h, Max : a) Surface dry (IS 101 (Part 3/Sec 1))-86)	1200.0
Table No. II (Drying time, Max b) Hard dry (IS 101 (Part 3/Sec 1))-86)	1200.0
Table No. II (Drying time, Max c) Hard dry at 70 Deg C (IS 101 (Part 3/Sec 1))-86)	1500.0
Table No. II (Consistency (IS 101 (Part 1/Sec 5)-89)	1200.0
Table No. II (Colour (IS 101 (Part 4/Sec 2)))	1200.0
Table No. II (Dry Film Thickness per coat, min. a) By Brush (IS 101 (Part 3/Sec 2)-89)	1200.0
Table No. II (Dry Film Thickness per coat, min. a) By airless spray (IS 101 (Part 3/Sec 2)-89)	1200.0
Table No. II (Volume Solid % min (Appendix-I))	2000.0
Table No. II (Scratch hardness, (Load 1.5 kg), (IS 101 (Part 5/Sec 2))-88)	1200.0
Table No. II (Flexibility and adhesion (IS 101 (Part 5/Sec 2))-88)	1200.0
Table No.II (Flash Point for both packs (IS 101 (Part 1/Sec 6)-87)	1200.0
Table No. II (Resistance to salt spray for 1000 hrs (IS 101 (Part 6/Sec 1)-88)	40000.0
Table No. II (Protection against corrosion under condition of condensation for 1000 hrs (IS 101 (Part 6/Sec 1)-88)	30000.0
Table No. II (Keeping Properties for Pack A, 18 Months (IS 101 (Part 6/Sec 2)-89)	7000.0
Table No. II (Keeping Properties for Pack B, 18 Months (IS 101 (Part 6/Sec 2)-89)	7000.0
Table No. II (Pot life a) at 27 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
Table No. II (Pot life a) at 40 (+/- 2 Deg. C), Minimum (Appendix-II))	1500.0
Table No. II (Mass in kg/10 liters, minimum (IS 101 (Part 1/Sec. 7)-87)	1200.0
Table No. II (Theoretical Coverage, Minimum (Appendix-I))	1200.0
Table No. II (Adhesion and compatibility with primer and finish coat (ASTM D 3359-97 & Appendix-II))	2000.0
Table No. II (Fineness of grind, minimum (IS 101 (Part 1/Sec. 7)-87)	1200.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Please refer Annexure)	1.0
RDSO SPECIFICATION No.M&C/PCN/129/2018 (Finish (IS 101 (Part 3/Sec 4)-1987))	1200.0
3.5b (Pigment content: (3.5b))	2000.0

492

Customized specification for Hypertron Hybrid - Customized specification for Hypertron Hybrid

Customized specification for Hypertron Hybrid

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Acid-Alkali resistance (Immersed membranesTensile strength and Elongation test)-As per test method ASTM D 412)	6000.0
- (Hardness(Shore D) - As per test method ASTM D 2240)	1000.0
- (Hardness(Shore A) - As per test method ASTM D 2240)	1000.0
- (Elongation (As per test method ASTM D 412))	2000.0
- (Tensile strength (As per test method ASTM D 412))	2000.0
- (Tear Resistance (As per test method ASTM D 624))	4000.0
- (Taber abrasion(As per test method ASTM D 4060))	3000.0
- (Water permeability of coating(As per test method ASTM E 96))	5000.0
- (Salt spray test-100 hours (As per test method ASTM B 117))	4000.0
- (Impact test (As per test method ASTM D 2794))	1500.0

493

IS 14768 : Part 2 (2003) - Conduit fittings for electrical installations - Specification: Part 1 general requirements

Conduit fittings for electrical installations - Specification: Part 1 general requirements

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9 (Construction of Conduit Fitting for Electrical Installations)	2000.0
10.3 (Impact Test as per IS 14768 Part1 Cl.10.3)	2000.0
10 (Suspended Load Test as per IS 14768 Part 1, Cl. 10.2)	2000.0
8 (Dimension of Conduit Fittings for Electrical Installations as per IS 14768 Part 1 Cl.8)	2000.0

494

Customized specification for News print paper - Customized specification for News print paper

Customized specification for News print paper

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Grammage (as per IS 1060 (Part 5/Sec 5)))	1000.0
- (Brightness (as per IS 1060 (Part 4/Sec 13) ))	2000.0
- (Smoothness(as per IS 1060 (Part 5/Sec 20))	2000.0

495

IS 9537 : Part 2 (1981) - Specification for conduits for electrical installations: Part 2 rigid steel conduits

Specification for conduits for electrical installations: Part 2 rigid steel conduits

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
9.2 (Bend Test)	1000.0
9.3 (Compression Test)	3000.0
7 (Wall thickness)	500.0
7 (Outside Diameter)	500.0
13 (External InfulanceTest)	2000.0

496

NTH(WR)/MECH/CUSTOM/006 (2023) - Hot rolled and Cold reduced Steel Sheets and Strips - Galvanized/ Galvannealed/ Electrogalvanized

Hot rolled and Cold reduced Steel Sheets and Strips - Galvanized/ Galvannealed/ Electrogalvanized

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Chemical Compositions as per IS 513 Part 1/IS 513 Part 2 / IS 1079 /IS 5986/ IS 277 /IS 17404/ ASTM A653 or any other relevant Standard Spec.)	7000.0
2.0 (Mass of Coating/ Triple Spot Coating Test as per IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec.)	2000.0
3 (Freedom From Defects - Visual Examination as per IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec.)	1000.0
4 (Dimension Measurements as per IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec.)	1000.0
5.1 (Tensile Test as per IS 1079/IS 513 Part-1/IS 513 Part-2/ IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec. and Test Method IS 1608 /ASTM E8)	1000.0
5.2 (Yield /0.2% Proof Stress as per IS 1079/IS 513 Part-1/IS 513 Part-2/ IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec. and Test Method IS 1608 /ASTM E8)	1000.0
5.3 (% of Elongation as per IS 1079/IS 513 Part-1/IS 513 Part-2/ IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec. and Test Method IS 1608 /ASTM E8)	1000.0
6 (Bend Test as per IS 1079/IS 513 Part-1/IS 513 Part-2/ IS 277/ IS 17404/ ASTM A653 or relevant Standard Spec. and referred test method)	1000.0
7 (Cupping Test as per IS 10175)	2000.0
8 (Hardness - Rockwell/Brinell/ Vickers as per IS 1586 Part-1/ IS1500 Part-1/ IS 1501 Part-1)	2000.0
2.1 (Nature of Coating /% of Coating Elements by AAS Method as per ISO 17925 or any other relevant method.)	2400.0

497

IS 1899 (1977) - Specification for blow lamps (Second Revision)

Specification for blow lamps (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3,6,7,8 and 11 (Blow Lamp Type and Size, Design and Dimension, Construction, Finish, Marking and Tests as per the clauses 3,6,7,8 and 11)	14000.0

498

Customized Specification for Weights and Measures(Wajan and Parimane) - Customized Specification for Weights and Measures(Wajan and Parimane)

Customized Specification for Weights and Measures(Wajan and Parimane)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Availability of Standard Weights (1g to 100g ))	3000.0

499

Customized Specification for glass items-Plain Miorror, Plain Slide, Watch glass - Customized Specification for glass items-Plain Mirror, Plain Slide, Watch glass

Customized Specification for glass items-Plain Mirror, Plain Slide, Watch glass

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Size Of Plain Mirror (3" x 2')±10%)	500.0
- (Diameter of Watch glass (3" ± 10%))	500.0
- (Visual Inspection)	1000.0

500

Customized Specification for Lens(Concave and Convex) - Customized Specification for Lens(Concave and Convex)

Customized Specification for Lens(Concave and Convex)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Visual inspection (Concave and convex lens without handle))	1000.0
- (Diameter of Concave and Convex Lens( 50 mm. ± 10%))	1000.0

501

Customized Specification for Geometric Box - Customized Specification for Geometric Box

Customized Specification for Geometric Box

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Visual inspection (12 no. of items))	1000.0

502

Customized Specification for Notes and Coins - Customized Specification for Notes and Coins

Customized Specification for Notes and Coins

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Visual inspection (Plastic or Paper Notes and Coins))	1000.0

503

Customized Specification for Measurement and Litre(Mape waznachi and Literchi) - Customized Specification for Measurement and Litre (Mape waznachi and Literchi)

Customized Specification for Measurement and Litre (Mape waznachi and Literchi)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Visual inspection)	1000.0

504

Customized Specification for Cycle Pump - Customized Specification for Cycle Pump

Customized Specification for Cycle Pump

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Length of Cycle Pump (20" ± 10%))	1000.0

505

Customized Specification for Transparent Mirror (wood and glass) - Customized Specification for Transparent Mirror (wood and glass)

Customized Specification for Transparent Mirror (wood and glass)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Transparent Mirror -Visual inspection (wood and glass))	1000.0

506

Customized Specification for Caleidoscope - Customized Specification for Caleidoscope

Customized Specification for Caleidoscope

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Identification of Material(Plastic body) by FTIR Method.)	2000.0

507

Customized Specification for Rubber ring - Customized Specification for Rubber ring

Customized Specification for Rubber ring

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Rubber ring size (1' to 1.5") ± 10%)	1000.0

508

Customized Specification for Pendulum (Dolangati Prayog Sahitya) - Customized Specification for Pendulum (Dolangati Prayog Sahitya)

Customized Specification for Pendulum (Dolangati Prayog Sahitya)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Diameter of Pendulum (18 mm. ± 10%))	1000.0

509

Customized Specification for Prizm - Customized Specification for Prizm

Customized Specification for Prizm

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Size of Glass Prizm (38 x 38 mm) ± 10%)	1000.0

510

Customized Specification for Centrifugal Machine(Upkendri Prayog Sahitya) - Customized Specification for Centrifugal Machine(Upkendri Prayog Sahitya)

Customized Specification for Centrifugal Machine(Upkendri Prayog Sahitya)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Visual inspection (Centrifugal Machine))	1000.0